summaryrefslogtreecommitdiffstats
path: root/drivers/net
Commit message (Collapse)AuthorAgeFilesLines
* ixgbe: fix unexpected VLAN Rx in promisc mode on VFOlivier Matz2022-06-141-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 7bb0fb7c63df95d6027dc50d6af3bc3bbbc25483 upstream. When the promiscuous mode is enabled on a VF, the IXGBE_VMOLR_VPE bit (VLAN Promiscuous Enable) is set. This means that the VF will receive packets whose VLAN is not the same than the VLAN of the VF. For instance, in this situation: ┌────────┐ ┌────────┐ ┌────────┐ │ │ │ │ │ │ │ │ │ │ │ │ │ VF0├────┤VF1 VF2├────┤VF3 │ │ │ │ │ │ │ └────────┘ └────────┘ └────────┘ VM1 VM2 VM3 vf 0: vlan 1000 vf 1: vlan 1000 vf 2: vlan 1001 vf 3: vlan 1001 If we tcpdump on VF3, we see all the packets, even those transmitted on vlan 1000. This behavior prevents to bridge VF1 and VF2 in VM2, because it will create a loop: packets transmitted on VF1 will be received by VF2 and vice-versa, and bridged again through the software bridge. This patch remove the activation of VLAN Promiscuous when a VF enables the promiscuous mode. However, the IXGBE_VMOLR_UPE bit (Unicast Promiscuous) is kept, so that a VF receives all packets that has the same VLAN, whatever the destination MAC address. Fixes: 8443c1a4b192 ("ixgbe, ixgbevf: Add new mbox API xcast mode") Cc: stable@vger.kernel.org Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Olivier Matz <olivier.matz@6wind.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ixgbe: fix bcast packets Rx on VF after promisc removalOlivier Matz2022-06-141-2/+2
| | | | | | | | | | | | | | | | | | | | | commit 803e9895ea2b0fe80bc85980ae2d7a7e44037914 upstream. After a VF requested to remove the promiscuous flag on an interface, the broadcast packets are not received anymore. This breaks some protocols like ARP. In ixgbe_update_vf_xcast_mode(), we should keep the IXGBE_VMOLR_BAM bit (Broadcast Accept) on promiscuous removal. This flag is already set by default in ixgbe_set_vmolr() on VF reset. Fixes: 8443c1a4b192 ("ixgbe, ixgbevf: Add new mbox API xcast mode") Cc: stable@vger.kernel.org Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Olivier Matz <olivier.matz@6wind.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: altera: Fix refcount leak in altera_tse_mdio_createMiaoqian Lin2022-06-141-1/+5
| | | | | | | | | | | | | | | | | [ Upstream commit 11ec18b1d8d92b9df307d31950dcba0b3dd7283c ] Every iteration of for_each_child_of_node() decrements the reference count of the previous node. When break from a for_each_child_of_node() loop, we need to explicitly call of_node_put() on the child node when not need anymore. Add missing of_node_put() to avoid refcount leak. Fixes: bbd2190ce96d ("Altera TSE: Add main and header file for Altera Ethernet Driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220607041144.7553-1-linmq006@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net/mlx5: fs, fail conflicting actionsMark Bloch2022-06-141-3/+32
| | | | | | | | | | | | | | | | | | | [ Upstream commit 8fa5e7b20e01042b14f8cd684d2da9b638460c74 ] When combining two steering rules into one check not only do they share the same actions but those actions are also the same. This resolves an issue where when creating two different rules with the same match the actions are overwritten and one of the rules is deleted a FW syndrome can be seen in dmesg. mlx5_core 0000:03:00.0: mlx5_cmd_check:819:(pid 2105): DEALLOC_MODIFY_HEADER_CONTEXT(0x941) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x1ab444) Fixes: 0d235c3fabb7 ("net/mlx5: Add hash table to search FTEs in a flow-group") Signed-off-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net/mlx5: Rearm the FW tracer after each tracer eventFeras Daoud2022-06-141-2/+5
| | | | | | | | | | | | | | | | [ Upstream commit 8bf94e6414c9481bfa28269022688ab445d0081d ] The current design does not arm the tracer if traces are available before the tracer string database is fully loaded, leading to an unfunctional tracer. This fix will rearm the tracer every time the FW triggers tracer event regardless of the tracer strings database status. Fixes: c71ad41ccb0c ("net/mlx5: FW tracer, events handling") Signed-off-by: Feras Daoud <ferasda@nvidia.com> Signed-off-by: Roy Novich <royno@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: mdio: unexport __init-annotated mdio_bus_init()Masahiro Yamada2022-06-141-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 35b42dce619701f1300fb8498dae82c9bb1f0263 ] EXPORT_SYMBOL and __init is a bad combination because the .init.text section is freed up after the initialization. Hence, modules cannot use symbols annotated __init. The access to a freed symbol may end up with kernel panic. modpost used to detect it, but it has been broken for a decade. Recently, I fixed modpost so it started to warn it again, then this showed up in linux-next builds. There are two ways to fix it: - Remove __init - Remove EXPORT_SYMBOL I chose the latter for this case because the only in-tree call-site, drivers/net/phy/phy_device.c is never compiled as modular. (CONFIG_PHYLIB is boolean) Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net/mlx4_en: Fix wrong return value on ioctl EEPROM query failureGal Pressman2022-06-141-1/+1
| | | | | | | | | | | | | | [ Upstream commit f5826c8c9d57210a17031af5527056eefdc2b7eb ] The ioctl EEPROM query wrongly returns success on read failures, fix that by returning the appropriate error code. Fixes: 7202da8b7f71 ("ethtool, net/mlx4_en: Cable info, get_module_info/eeprom ethtool support") Signed-off-by: Gal Pressman <gal@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/20220606115718.14233-1-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: dsa: lantiq_gswip: Fix refcount leak in gswip_gphy_fw_listMiaoqian Lin2022-06-141-1/+3
| | | | | | | | | | | | | | | | [ Upstream commit 0737e018a05e2aa352828c52bdeed3b02cff2930 ] Every iteration of for_each_available_child_of_node() decrements the reference count of the previous node. when breaking early from a for_each_available_child_of_node() loop, we need to explicitly call of_node_put() on the gphy_fw_np. Add missing of_node_put() to avoid refcount leak. Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220605072335.11257-1-linmq006@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net/mlx5e: Update netdev features after changing XDP stateMaxim Mikityanskiy2022-06-141-0/+5
| | | | | | | | | | | | | | | | | [ Upstream commit f6279f113ad593971999c877eb69dc3d36a75894 ] Some features (LRO, HW GRO) conflict with XDP. If there is an attempt to enable such features while XDP is active, they will be set to `off [requested on]`. In order to activate these features after XDP is turned off, the driver needs to call netdev_update_features(). This commit adds this missing call after XDP state changes. Fixes: cf6e34c8c22f ("net/mlx5e: Properly block LRO when XDP is enabled") Fixes: b0617e7b3500 ("net/mlx5e: Properly block HW GRO when XDP is enabled") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net/mlx5: Don't use already freed action pointerLeon Romanovsky2022-06-141-5/+4
| | | | | | | | | | | | | | | | | | | [ Upstream commit 80b2bd737d0e833e6a2b77e482e5a714a79c86a4 ] The call to mlx5dr_action_destroy() releases "action" memory. That pointer is set to miss_action later and generates the following smatch error: drivers/net/ethernet/mellanox/mlx5/core/steering/fs_dr.c:53 set_miss_action() warn: 'action' was already freed. Make sure that the pointer is always valid by setting NULL after destroy. Fixes: 6a48faeeca10 ("net/mlx5: Add direct rule fs_cmd implementation") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* nfp: only report pause frame configuration for physical deviceYu Xiao2022-06-141-2/+2
| | | | | | | | | | | | | [ Upstream commit 0649e4d63420ebc8cbebef3e9d39e12ffc5eb9fa ] Only report pause frame configuration for physical device. Logical port of both PCI PF and PCI VF do not support it. Fixes: 9fdc5d85a8fe ("nfp: update ethtool reporting of pauseframe control") Signed-off-by: Yu Xiao <yu.xiao@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: dsa: mv88e6xxx: Fix refcount leak in mv88e6xxx_mdios_registerMiaoqian Lin2022-06-141-0/+1
| | | | | | | | | | | | | | | | | | [ Upstream commit 02ded5a173619b11728b8bf75a3fd995a2c1ff28 ] of_get_child_by_name() returns a node pointer with refcount incremented, we should use of_node_put() on it when done. mv88e6xxx_mdio_register() pass the device node to of_mdiobus_register(). We don't need the device node after it. Add missing of_node_put() to avoid refcount leak. Fixes: a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO busses") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Marek Behún <kabel@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: ethernet: mtk_eth_soc: out of bounds read in mtk_hwlro_get_fdir_entry()Dan Carpenter2022-06-141-0/+3
| | | | | | | | | | | | [ Upstream commit e7e7104e2d5ddf3806a28695670f21bef471f1e1 ] The "fsp->location" variable comes from user via ethtool_get_rxnfc(). Check that it is valid to prevent an out of bounds read. Fixes: 7aab747e5563 ("net: ethernet: mediatek: add ethtool functions to configure RX flows of HW LRO") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* carl9170: tx: fix an incorrect use of list iteratorXiaomeng Tong2022-06-141-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | commit 54a6f29522da3c914da30e50721dedf51046449a upstream. If the previous list_for_each_entry_continue_rcu() don't exit early (no goto hit inside the loop), the iterator 'cvif' after the loop will be a bogus pointer to an invalid structure object containing the HEAD (&ar->vif_list). As a result, the use of 'cvif' after that will lead to a invalid memory access (i.e., 'cvif->id': the invalid pointer dereference when return back to/after the callsite in the carl9170_update_beacon()). The original intention should have been to return the valid 'cvif' when found in list, NULL otherwise. So just return NULL when no entry found, to fix this bug. Cc: stable@vger.kernel.org Fixes: 1f1d9654e183c ("carl9170: refactor carl9170_update_beacon") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220328122820.1004-1-xiam0nd.tong@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* rtl818x: Prevent using not initialized queuesAlexander Wetzel2022-06-141-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 746285cf81dc19502ab238249d75f5990bd2d231 upstream. Using not existing queues can panic the kernel with rtl8180/rtl8185 cards. Ignore the skb priority for those cards, they only have one tx queue. Pierre Asselin (pa@panix.com) reported the kernel crash in the Gentoo forum: https://forums.gentoo.org/viewtopic-t-1147832-postdays-0-postorder-asc-start-25.html He also confirmed that this patch fixes the issue. In summary this happened: After updating wpa_supplicant from 2.9 to 2.10 the kernel crashed with a "divide error: 0000" when connecting to an AP. Control port tx now tries to use IEEE80211_AC_VO for the priority, which wpa_supplicants starts to use in 2.10. Since only the rtl8187se part of the driver supports QoS, the priority of the skb is set to IEEE80211_AC_BE (2) by mac80211 for rtl8180/rtl8185 cards. rtl8180 is then unconditionally reading out the priority and finally crashes on drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c line 544 without this patch: idx = (ring->idx + skb_queue_len(&ring->queue)) % ring->entries "ring->entries" is zero for rtl8180/rtl8185 cards, tx_ring[2] never got initialized. Cc: stable@vger.kernel.org Reported-by: pa@panix.com Tested-by: pa@panix.com Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220422145228.7567-1-alexander@wetzel-home.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* iwlwifi: mvm: fix assert 1F04 upon reconfigEmmanuel Grumbach2022-06-141-0/+3
| | | | | | | | | | | | | | | | commit 9d096e3d3061dbf4ee10e2b59fc2c06e05bdb997 upstream. When we reconfig we must not send the MAC_POWER command that relates to a MAC that was not yet added to the firmware. Ignore those in the iterator. Cc: stable@vger.kernel.org Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Link: https://lore.kernel.org/r/20220517120044.ed2ffc8ce732.If786e19512d0da4334a6382ea6148703422c7d7b@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* can: xilinx_can: mark bit timing constants as constMarc Kleine-Budde2022-06-141-2/+2
| | | | | | | | | | | | | [ Upstream commit ae38fda02996d43d9fb09f16e81e0008704dd524 ] This patch marks the bit timing constants as const. Fixes: c223da689324 ("can: xilinx_can: Add support for CANFD FD frames") Link: https://lore.kernel.org/all/20220317203119.792552-1-mkl@pengutronix.de Cc: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com> Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
* ath9k_htc: fix potential out of bounds access with invalid rxstatus->rs_keyixDan Carpenter2022-06-141-0/+8
| | | | | | | | | | | | | | | | | [ Upstream commit 2dc509305cf956381532792cb8dceef2b1504765 ] The "rxstatus->rs_keyix" eventually gets passed to test_bit() so we need to ensure that it is within the bitmap. drivers/net/wireless/ath/ath9k/common.c:46 ath9k_cmn_rx_accept() error: passing untrusted data 'rx_stats->rs_keyix' to 'test_bit()' Fixes: 4ed1a8d4a257 ("ath9k_htc: use ath9k_cmn_rx_accept") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220409061225.GA5447@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
* ath9k: fix ar9003_get_eepmiscWenli Looi2022-06-141-1/+1
| | | | | | | | | | | | | [ Upstream commit 9aaff3864b603408c02c629957ae8d8ff5d5a4f2 ] The current implementation is reading the wrong eeprom type. Fixes: d8ec2e2a63e8 ("ath9k: Add an eeprom_ops callback for retrieving the eepmisc value") Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220320233010.123106-5-wlooi@ucalgary.ca Signed-off-by: Sasha Levin <sashal@kernel.org>
* eth: tg3: silence the GCC 12 array-bounds warningJakub Kicinski2022-06-141-0/+5
| | | | | | | | | | | | | | | | | | | | [ Upstream commit 9dec850fd7c210a04b4707df8e6c95bfafdd6a4b ] GCC 12 currently generates a rather inconsistent warning: drivers/net/ethernet/broadcom/tg3.c:17795:51: warning: array subscript 5 is above array bounds of ‘struct tg3_napi[5]’ [-Warray-bounds] 17795 | struct tg3_napi *tnapi = &tp->napi[i]; | ~~~~~~~~^~~ i is guaranteed < tp->irq_max which in turn is either 1 or 5. There are more loops like this one in the driver, but strangely GCC 12 dislikes only this single one. Silence this silliness for now. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: phy: micrel: Allow probing without .driver_dataFabio Estevam2022-06-141-5/+6
| | | | | | | | | | | | | | | | [ Upstream commit f2ef6f7539c68c6bd6c32323d8845ee102b7c450 ] Currently, if the .probe element is present in the phy_driver structure and the .driver_data is not, a NULL pointer dereference happens. Allow passing .probe without .driver_data by inserting NULL checks for priv->type. Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220513114613.762810-1-festevam@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* rtlwifi: Use pr_warn instead of WARN_ONCEDongliang Mu2022-06-141-1/+1
| | | | | | | | | | | | | | | [ Upstream commit ad732da434a2936128769216eddaece3b1af4588 ] This memory allocation failure can be triggered by fault injection or high pressure testing, resulting a WARN. Fix this by replacing WARN with pr_warn. Reported-by: syzkaller <syzkaller@googlegroups.com> Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220511014453.1621366-1-dzm91@hust.edu.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
* mlxsw: spectrum_dcb: Do not warn about priority changesPetr Machata2022-06-141-13/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit b6b584562cbe7dc357083459d6dd5b171e12cadb ] The idea behind the warnings is that the user would get warned in case when more than one priority is configured for a given DSCP value on a netdevice. The warning is currently wrong, because dcb_ieee_getapp_mask() returns the first matching entry, not all of them, and the warning will then claim that some priority is "current", when in fact it is not. But more importantly, the warning is misleading in general. Consider the following commands: # dcb app flush dev swp19 dscp-prio # dcb app add dev swp19 dscp-prio 24:3 # dcb app replace dev swp19 dscp-prio 24:2 The last command will issue the following warning: mlxsw_spectrum3 0000:07:00.0 swp19: Ignoring new priority 2 for DSCP 24 in favor of current value of 3 The reason is that the "replace" command works by first adding the new value, and then removing all old values. This is the only way to make the replacement without causing the traffic to be prioritized to whatever the chip defaults to. The warning is issued in response to adding the new priority, and then no warning is shown when the old priority is removed. The upshot is that the canonical way to change traffic prioritization always produces a warning about ignoring the new priority, but what gets configured is in fact what the user intended. An option to just emit warning every time that the prioritization changes just to make it clear that it happened is obviously unsatisfactory. Therefore, in this patch, remove the warnings. Reported-by: Maksym Yaremchuk <maksymy@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net/mlx5: fs, delete the FTE when there are no rules attached to itMark Bloch2022-06-141-5/+5
| | | | | | | | | | | | | | | [ Upstream commit 7b0c6338597613f465d131bd939a51844a00455a ] When an FTE has no children is means all the rules where removed and the FTE can be deleted regardless of the dests_size value. While dests_size should be 0 when there are no children be extra careful not to leak memory or get firmware syndrome if the proper bookkeeping of dests_size wasn't done. Signed-off-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* ath9k: fix QCA9561 PA bias levelThibaut VARÈNE2022-06-141-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit e999a5da28a0e0f7de242d841ef7d5e48f4646ae ] This patch fixes an invalid TX PA DC bias level on QCA9561, which results in a very low output power and very low throughput as devices are further away from the AP (compared to other 2.4GHz APs). This patch was suggested by Felix Fietkau, who noted[1]: "The value written to that register is wrong, because while the mask definition AR_CH0_TOP2_XPABIASLVL uses a different value for 9561, the shift definition AR_CH0_TOP2_XPABIASLVL_S is hardcoded to 12, which is wrong for 9561." In real life testing, without this patch the 2.4GHz throughput on Yuncore XD3200 is around 10Mbps sitting next to the AP, and closer to practical maximum with the patch applied. [1] https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name Signed-off-by: Thibaut VARÈNE <hacks+kernel@slashdirt.org> Acked-by: Felix Fietkau <nbd@nbd.name> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220417145145.1847-1-hacks+kernel@slashdirt.org Signed-off-by: Sasha Levin <sashal@kernel.org>
* ipw2x00: Fix potential NULL dereference in libipw_xmit()Haowen Bai2022-06-141-1/+1
| | | | | | | | | | | | [ Upstream commit e8366bbabe1d207cf7c5b11ae50e223ae6fc278b ] crypt and crypt->ops could be null, so we need to checking null before dereference Signed-off-by: Haowen Bai <baihaowen@meizu.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/1648797055-25730-1-git-send-email-baihaowen@meizu.com Signed-off-by: Sasha Levin <sashal@kernel.org>
* b43: Fix assigning negative value to unsigned variableHaowen Bai2022-06-141-1/+1
| | | | | | | | | | | | | [ Upstream commit 11800d893b38e0e12d636c170c1abc19c43c730c ] fix warning reported by smatch: drivers/net/wireless/broadcom/b43/phy_n.c:585 b43_nphy_adjust_lna_gain_table() warn: assigning (-2) to unsigned variable '*(lna_gain[0])' Signed-off-by: Haowen Bai <baihaowen@meizu.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/1648203315-28093-1-git-send-email-baihaowen@meizu.com Signed-off-by: Sasha Levin <sashal@kernel.org>
* b43legacy: Fix assigning negative value to unsigned variableHaowen Bai2022-06-141-1/+1
| | | | | | | | | | | | | [ Upstream commit 3f6b867559b3d43a7ce1b4799b755e812fc0d503 ] fix warning reported by smatch: drivers/net/wireless/broadcom/b43legacy/phy.c:1181 b43legacy_phy_lo_b_measure() warn: assigning (-772) to unsigned variable 'fval' Signed-off-by: Haowen Bai <baihaowen@meizu.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/1648203433-8736-1-git-send-email-baihaowen@meizu.com Signed-off-by: Sasha Levin <sashal@kernel.org>
* mwifiex: add mutex lock for call in mwifiex_dfs_chan_sw_work_queueNiels Dossche2022-06-141-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 3e12968f6d12a34b540c39cbd696a760cc4616f0 ] cfg80211_ch_switch_notify uses ASSERT_WDEV_LOCK to assert that net_device->ieee80211_ptr->mtx (which is the same as priv->wdev.mtx) is held during the function's execution. mwifiex_dfs_chan_sw_work_queue is one of its callers, which does not hold that lock, therefore violating the assertion. Add a lock around the call. Disclaimer: I am currently working on a static analyser to detect missing locks. This was a reported case. I manually verified the report by looking at the code, so that I do not send wrong information or patches. After concluding that this seems to be a true positive, I created this patch. However, as I do not in fact have this particular hardware, I was unable to test it. Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220321225515.32113-1-dossche.niels@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: ftgmac100: Disable hardware checksum on AST2600Joel Stanley2022-06-061-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 6fd45e79e8b93b8d22fb8fe22c32fbad7e9190bd ] The AST2600 when using the i210 NIC over NC-SI has been observed to produce incorrect checksum results with specific MTU values. This was first observed when sending data across a long distance set of networks. On a local network, the following test was performed using a 1MB file of random data. On the receiver run this script: #!/bin/bash while [ 1 ]; do # Zero the stats nstat -r > /dev/null nc -l 9899 > test-file # Check for checksum errors TcpInCsumErrors=$(nstat | grep TcpInCsumErrors) if [ -z "$TcpInCsumErrors" ]; then echo No TcpInCsumErrors else echo TcpInCsumErrors = $TcpInCsumErrors fi done On an AST2600 system: # nc <IP of receiver host> 9899 < test-file The test was repeated with various MTU values: # ip link set mtu 1410 dev eth0 The observed results: 1500 - good 1434 - bad 1400 - good 1410 - bad 1420 - good The test was repeated after disabling tx checksumming: # ethtool -K eth0 tx-checksumming off And all MTU values tested resulted in transfers without error. An issue with the driver cannot be ruled out, however there has been no bug discovered so far. David has done the work to take the original bug report of slow data transfer between long distance connections and triaged it down to this test case. The vendor suspects this this is a hardware issue when using NC-SI. The fixes line refers to the patch that introduced AST2600 support. Reported-by: David Wilder <wilder@us.ibm.com> Reviewed-by: Dylan Hung <dylan_hung@aspeedtech.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: stmmac: disable Split Header (SPH) for Intel platformsTan Tee Min2022-05-252-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit 47f753c1108e287edb3e27fad8a7511a9d55578e upstream. Based on DesignWare Ethernet QoS datasheet, we are seeing the limitation of Split Header (SPH) feature is not supported for Ipv4 fragmented packet. This SPH limitation will cause ping failure when the packets size exceed the MTU size. For example, the issue happens once the basic ping packet size is larger than the configured MTU size and the data is lost inside the fragmented packet, replaced by zeros/corrupted values, and leads to ping fail. So, disable the Split Header for Intel platforms. v2: Add fixes tag in commit message. Fixes: 67afd6d1cfdf("net: stmmac: Add Split Header support and enable it in XGMAC cores") Cc: <stable@vger.kernel.org> # 5.10.x Suggested-by: Ong, Boon Leong <boon.leong.ong@intel.com> Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com> Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: atlantic: verify hw_head_ lies within TX buffer ringGrant Grundler2022-05-251-0/+7
| | | | | | | | | | | | | | [ Upstream commit 2120b7f4d128433ad8c5f503a9584deba0684901 ] Bounds check hw_head index provided by NIC to verify it lies within the TX buffer ring. Reported-by: Aashay Shringarpure <aashay@google.com> Reported-by: Yi Chou <yich@google.com> Reported-by: Shervin Oloumi <enlightened@google.com> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: stmmac: fix missing pci_disable_device() on error in stmmac_pci_probe()Yang Yingliang2022-05-251-3/+1
| | | | | | | | | | | | [ Upstream commit 0807ce0b010418a191e0e4009803b2d74c3245d5 ] Switch to using pcim_enable_device() to avoid missing pci_disable_device(). Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20220510031316.1780409-1-yangyingliang@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* ethernet: tulip: fix missing pci_disable_device() on error in tulip_init_one()Yang Yingliang2022-05-251-1/+4
| | | | | | | | | | | | | [ Upstream commit 51ca86b4c9c7c75f5630fa0dbe5f8f0bd98e3c3e ] Fix the missing pci_disable_device() before return from tulip_init_one() in the error handling case. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20220506094250.3630615-1-yangyingliang@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* igb: skip phy status check where unavailableKevin Mitchell2022-05-251-1/+2
| | | | | | | | | | | | | | | | | | | | | [ Upstream commit 942d2ad5d2e0df758a645ddfadffde2795322728 ] igb_read_phy_reg() will silently return, leaving phy_data untouched, if hw->ops.read_reg isn't set. Depending on the uninitialized value of phy_data, this led to the phy status check either succeeding immediately or looping continuously for 2 seconds before emitting a noisy err-level timeout. This message went out to the console even though there was no actual problem. Instead, first check if there is read_reg function pointer. If not, proceed without trying to check the phy status register. Fixes: b72f3f72005d ("igb: When GbE link up, wait for Remote receiver status condition") Signed-off-by: Kevin Mitchell <kevmitch@arista.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net/mlx5e: Properly block LRO when XDP is enabledMaxim Mikityanskiy2022-05-251-0/+7
| | | | | | | | | | | | | | | | | | [ Upstream commit cf6e34c8c22fba66bd21244b95ea47e235f68974 ] LRO is incompatible and mutually exclusive with XDP. However, the needed checks are only made when enabling XDP. If LRO is enabled when XDP is already active, the command will succeed, and XDP will be skipped in the data path, although still enabled. This commit fixes the bug by checking the XDP status in mlx5e_fix_features and disabling LRO if XDP is enabled. Fixes: 86994156c736 ("net/mlx5e: XDP fast RX drop bpf programs support") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net/qla3xxx: Fix a test in ql_reset_work()Christophe JAILLET2022-05-251-1/+2
| | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 5361448e45fac6fb96738df748229432a62d78b6 ] test_bit() tests if one bit is set or not. Here the logic seems to check of bit QL_RESET_PER_SCSI (i.e. 4) OR bit QL_RESET_START (i.e. 3) is set. In fact, it checks if bit 7 (4 | 3 = 7) is set, that is to say QL_ADAPTER_UP. This looks harmless, because this bit is likely be set, and when the ql_reset_work() delayed work is scheduled in ql3xxx_isr() (the only place that schedule this work), QL_RESET_START or QL_RESET_PER_SCSI is set. This has been spotted by smatch. Fixes: 5a4faa873782 ("[PATCH] qla3xxx NIC driver") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/80e73e33f390001d9c0140ffa9baddf6466a41a2.1652637337.git.christophe.jaillet@wanadoo.fr Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* ice: fix possible under reporting of ethtool Tx and Rx statisticsPaul Greenwalt2022-05-251-3/+4
| | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 31b6298fd8e29effe9ed6b77351ac5969be56ce0 ] The hardware statistics counters are not cleared during resets so the drivers first access is to initialize the baseline and then subsequent reads are for reporting the counters. The statistics counters are read during the watchdog subtask when the interface is up. If the baseline is not initialized before the interface is up, then there can be a brief window in which some traffic can be transmitted/received before the initial baseline reading takes place. Directly initialize ethtool statistics in driver open so the baseline will be initialized when the interface is up, and any dropped packets incremented before the interface is up won't be reported. Fixes: 28dc1b86f8ea9 ("ice: ignore dropped packets during init") Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: vmxnet3: fix possible NULL pointer dereference in vmxnet3_rq_cleanup()Zixuan Fu2022-05-251-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit edf410cb74dc612fd47ef5be319c5a0bcd6e6ccd ] In vmxnet3_rq_create(), when dma_alloc_coherent() fails, vmxnet3_rq_destroy() is called. It sets rq->rx_ring[i].base to NULL. Then vmxnet3_rq_create() returns an error to its callers mxnet3_rq_create_all() -> vmxnet3_change_mtu(). Then vmxnet3_change_mtu() calls vmxnet3_force_close() -> dev_close() in error handling code. And the driver calls vmxnet3_close() -> vmxnet3_quiesce_dev() -> vmxnet3_rq_cleanup_all() -> vmxnet3_rq_cleanup(). In vmxnet3_rq_cleanup(), rq->rx_ring[ring_idx].base is accessed, but this variable is NULL, causing a NULL pointer dereference. To fix this possible bug, an if statement is added to check whether rq->rx_ring[0].base is NULL in vmxnet3_rq_cleanup() and exit early if so. The error log in our fault-injection testing is shown as follows: [ 65.220135] BUG: kernel NULL pointer dereference, address: 0000000000000008 ... [ 65.222633] RIP: 0010:vmxnet3_rq_cleanup_all+0x396/0x4e0 [vmxnet3] ... [ 65.227977] Call Trace: ... [ 65.228262] vmxnet3_quiesce_dev+0x80f/0x8a0 [vmxnet3] [ 65.228580] vmxnet3_close+0x2c4/0x3f0 [vmxnet3] [ 65.228866] __dev_close_many+0x288/0x350 [ 65.229607] dev_close_many+0xa4/0x480 [ 65.231124] dev_close+0x138/0x230 [ 65.231933] vmxnet3_force_close+0x1f0/0x240 [vmxnet3] [ 65.232248] vmxnet3_change_mtu+0x75d/0x920 [vmxnet3] ... Fixes: d1a890fa37f27 ("net: VMware virtual Ethernet NIC driver: vmxnet3") Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Zixuan Fu <r33s3n6@gmail.com> Link: https://lore.kernel.org/r/20220514050711.2636709-1-r33s3n6@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: vmxnet3: fix possible use-after-free bugs in vmxnet3_rq_alloc_rx_buf()Zixuan Fu2022-05-251-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 9e7fef9521e73ca8afd7da9e58c14654b02dfad8 ] In vmxnet3_rq_alloc_rx_buf(), when dma_map_single() fails, rbi->skb is freed immediately. Similarly, in another branch, when dma_map_page() fails, rbi->page is also freed. In the two cases, vmxnet3_rq_alloc_rx_buf() returns an error to its callers vmxnet3_rq_init() -> vmxnet3_rq_init_all() -> vmxnet3_activate_dev(). Then vmxnet3_activate_dev() calls vmxnet3_rq_cleanup_all() in error handling code, and rbi->skb or rbi->page are freed again in vmxnet3_rq_cleanup_all(), causing use-after-free bugs. To fix these possible bugs, rbi->skb and rbi->page should be cleared after they are freed. The error log in our fault-injection testing is shown as follows: [ 14.319016] BUG: KASAN: use-after-free in consume_skb+0x2f/0x150 ... [ 14.321586] Call Trace: ... [ 14.325357] consume_skb+0x2f/0x150 [ 14.325671] vmxnet3_rq_cleanup_all+0x33a/0x4e0 [vmxnet3] [ 14.326150] vmxnet3_activate_dev+0xb9d/0x2ca0 [vmxnet3] [ 14.326616] vmxnet3_open+0x387/0x470 [vmxnet3] ... [ 14.361675] Allocated by task 351: ... [ 14.362688] __netdev_alloc_skb+0x1b3/0x6f0 [ 14.362960] vmxnet3_rq_alloc_rx_buf+0x1b0/0x8d0 [vmxnet3] [ 14.363317] vmxnet3_activate_dev+0x3e3/0x2ca0 [vmxnet3] [ 14.363661] vmxnet3_open+0x387/0x470 [vmxnet3] ... [ 14.367309] [ 14.367412] Freed by task 351: ... [ 14.368932] __dev_kfree_skb_any+0xd2/0xe0 [ 14.369193] vmxnet3_rq_alloc_rx_buf+0x71e/0x8d0 [vmxnet3] [ 14.369544] vmxnet3_activate_dev+0x3e3/0x2ca0 [vmxnet3] [ 14.369883] vmxnet3_open+0x387/0x470 [vmxnet3] [ 14.370174] __dev_open+0x28a/0x420 [ 14.370399] __dev_change_flags+0x192/0x590 [ 14.370667] dev_change_flags+0x7a/0x180 [ 14.370919] do_setlink+0xb28/0x3570 [ 14.371150] rtnl_newlink+0x1160/0x1740 [ 14.371399] rtnetlink_rcv_msg+0x5bf/0xa50 [ 14.371661] netlink_rcv_skb+0x1cd/0x3e0 [ 14.371913] netlink_unicast+0x5dc/0x840 [ 14.372169] netlink_sendmsg+0x856/0xc40 [ 14.372420] ____sys_sendmsg+0x8a7/0x8d0 [ 14.372673] __sys_sendmsg+0x1c2/0x270 [ 14.372914] do_syscall_64+0x41/0x90 [ 14.373145] entry_SYSCALL_64_after_hwframe+0x44/0xae ... Fixes: 5738a09d58d5a ("vmxnet3: fix checks for dma mapping errors") Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Zixuan Fu <r33s3n6@gmail.com> Link: https://lore.kernel.org/r/20220514050656.2636588-1-r33s3n6@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: macb: Increment rx bd head after allocating skb and bufferHarini Katakam2022-05-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 9500acc631dbb8b73166e25700e656b11f6007b6 ] In gem_rx_refill rx_prepared_head is incremented at the beginning of the while loop preparing the skb and data buffers. If the skb or data buffer allocation fails, this BD will be unusable BDs until the head loops back to the same BD (and obviously buffer allocation succeeds). In the unlikely event that there's a string of allocation failures, there will be an equal number of unusable BDs and an inconsistent RX BD chain. Hence increment the head at the end of the while loop to be clean. Fixes: 4df95131ea80 ("net/macb: change RX path for GEM") Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20220512171900.32593-1-harini.katakam@xilinx.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: phy: Fix race condition on link status changeFrancesco Dolcini2022-05-181-5/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 91a7cda1f4b8bdf770000a3b60640576dafe0cec upstream. This fixes the following error caused by a race condition between phydev->adjust_link() and a MDIO transaction in the phy interrupt handler. The issue was reproduced with the ethernet FEC driver and a micrel KSZ9031 phy. [ 146.195696] fec 2188000.ethernet eth0: MDIO read timeout [ 146.201779] ------------[ cut here ]------------ [ 146.206671] WARNING: CPU: 0 PID: 571 at drivers/net/phy/phy.c:942 phy_error+0x24/0x6c [ 146.214744] Modules linked in: bnep imx_vdoa imx_sdma evbug [ 146.220640] CPU: 0 PID: 571 Comm: irq/128-2188000 Not tainted 5.18.0-rc3-00080-gd569e86915b7 #9 [ 146.229563] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [ 146.236257] unwind_backtrace from show_stack+0x10/0x14 [ 146.241640] show_stack from dump_stack_lvl+0x58/0x70 [ 146.246841] dump_stack_lvl from __warn+0xb4/0x24c [ 146.251772] __warn from warn_slowpath_fmt+0x5c/0xd4 [ 146.256873] warn_slowpath_fmt from phy_error+0x24/0x6c [ 146.262249] phy_error from kszphy_handle_interrupt+0x40/0x48 [ 146.268159] kszphy_handle_interrupt from irq_thread_fn+0x1c/0x78 [ 146.274417] irq_thread_fn from irq_thread+0xf0/0x1dc [ 146.279605] irq_thread from kthread+0xe4/0x104 [ 146.284267] kthread from ret_from_fork+0x14/0x28 [ 146.289164] Exception stack(0xe6fa1fb0 to 0xe6fa1ff8) [ 146.294448] 1fa0: 00000000 00000000 00000000 00000000 [ 146.302842] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 146.311281] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 146.318262] irq event stamp: 12325 [ 146.321780] hardirqs last enabled at (12333): [<c01984c4>] __up_console_sem+0x50/0x60 [ 146.330013] hardirqs last disabled at (12342): [<c01984b0>] __up_console_sem+0x3c/0x60 [ 146.338259] softirqs last enabled at (12324): [<c01017f0>] __do_softirq+0x2c0/0x624 [ 146.346311] softirqs last disabled at (12319): [<c01300ac>] __irq_exit_rcu+0x138/0x178 [ 146.354447] ---[ end trace 0000000000000000 ]--- With the FEC driver phydev->adjust_link() calls fec_enet_adjust_link() calls fec_stop()/fec_restart() and both these function reset and temporary disable the FEC disrupting any MII transaction that could be happening at the same time. fec_enet_adjust_link() and phy_read() can be running at the same time when we have one additional interrupt before the phy_state_machine() is able to terminate. Thread 1 (phylib WQ) | Thread 2 (phy interrupt) | | phy_interrupt() <-- PHY IRQ | handle_interrupt() | phy_read() | phy_trigger_machine() | --> schedule phylib WQ | | phy_state_machine() | phy_check_link_status() | phy_link_change() | phydev->adjust_link() | fec_enet_adjust_link() | --> FEC reset | phy_interrupt() <-- PHY IRQ | phy_read() | Fix this by acquiring the phydev lock in phy_interrupt(). Link: https://lore.kernel.org/all/20220422152612.GA510015@francesco-nb.int.toradex.com/ Fixes: c974bdbc3e77 ("net: phy: Use threaded IRQ, to allow IRQ from sleeping devices") cc: <stable@vger.kernel.org> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220506060815.327382-1-francesco.dolcini@toradex.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> [fd: backport: adapt locking before did_interrupt()/ack_interrupt() callbacks removal ] Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* i40e: i40e_main: fix a missing check on list iteratorXiaomeng Tong2022-05-181-13/+14
| | | | | | | | | | | | | | | | | | | | | | | | | commit 3f95a7472d14abef284d8968734fe2ae7ff4845f upstream. The bug is here: ret = i40e_add_macvlan_filter(hw, ch->seid, vdev->dev_addr, &aq_err); The list iterator 'ch' will point to a bogus position containing HEAD if the list is empty or no element is found. This case must be checked before any use of the iterator, otherwise it will lead to a invalid memory access. To fix this bug, use a new variable 'iter' as the list iterator, while use the origin variable 'ch' as a dedicated pointer to point to the found element. Cc: stable@vger.kernel.org Fixes: 1d8d80b4e4ff6 ("i40e: Add macvlan support on i40e") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20220510204846.2166999-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: emaclite: Don't advertise 1000BASE-T and do auto negotiationShravya Kumbham2022-05-181-15/+0
| | | | | | | | | | | | | | | | | | [ Upstream commit b800528b97d0adc3a5ba42d78a8b0d3f07a31f44 ] In xemaclite_open() function we are setting the max speed of emaclite to 100Mb using phy_set_max_speed() function so, there is no need to write the advertising registers to stop giga-bit speed and the phy_start() function starts the auto-negotiation so, there is no need to handle it separately using advertising registers. Remove the phy_read and phy_write of advertising registers in xemaclite_open() function. Signed-off-by: Shravya Kumbham <shravya.kumbham@xilinx.com> Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* net: sfc: ef10: fix memory leak in efx_ef10_mtd_probe()Taehee Yoo2022-05-181-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 1fa89ffbc04545b7582518e57f4b63e2a062870f ] In the NIC ->probe() callback, ->mtd_probe() callback is called. If NIC has 2 ports, ->probe() is called twice and ->mtd_probe() too. In the ->mtd_probe(), which is efx_ef10_mtd_probe() it allocates and initializes mtd partiion. But mtd partition for sfc is shared data. So that allocated mtd partition data from last called efx_ef10_mtd_probe() will not be used. Therefore it must be freed. But it doesn't free a not used mtd partition data in efx_ef10_mtd_probe(). kmemleak reports: unreferenced object 0xffff88811ddb0000 (size 63168): comm "systemd-udevd", pid 265, jiffies 4294681048 (age 348.586s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffffa3767749>] kmalloc_order_trace+0x19/0x120 [<ffffffffa3873f0e>] __kmalloc+0x20e/0x250 [<ffffffffc041389f>] efx_ef10_mtd_probe+0x11f/0x270 [sfc] [<ffffffffc0484c8a>] efx_pci_probe.cold.17+0x3df/0x53d [sfc] [<ffffffffa414192c>] local_pci_probe+0xdc/0x170 [<ffffffffa4145df5>] pci_device_probe+0x235/0x680 [<ffffffffa443dd52>] really_probe+0x1c2/0x8f0 [<ffffffffa443e72b>] __driver_probe_device+0x2ab/0x460 [<ffffffffa443e92a>] driver_probe_device+0x4a/0x120 [<ffffffffa443f2ae>] __driver_attach+0x16e/0x320 [<ffffffffa4437a90>] bus_for_each_dev+0x110/0x190 [<ffffffffa443b75e>] bus_add_driver+0x39e/0x560 [<ffffffffa4440b1e>] driver_register+0x18e/0x310 [<ffffffffc02e2055>] 0xffffffffc02e2055 [<ffffffffa3001af3>] do_one_initcall+0xc3/0x450 [<ffffffffa33ca574>] do_init_module+0x1b4/0x700 Acked-by: Martin Habets <habetsm.xilinx@gmail.com> Fixes: 8127d661e77f ("sfc: Add support for Solarflare SFC9100 family") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Link: https://lore.kernel.org/r/20220512054709.12513-1-ap420073@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* mac80211_hwsim: call ieee80211_tx_prepare_skb under RCU protectionJohannes Berg2022-05-181-0/+3
| | | | | | | | | | | | | | | [ Upstream commit 9e2db50f1ef2238fc2f71c5de1c0418b7a5b0ea2 ] This is needed since it might use (and pass out) pointers to e.g. keys protected by RCU. Can't really happen here as the frames aren't encrypted, but we need to still adhere to the rules. Fixes: cacfddf82baf ("mac80211_hwsim: initialize ieee80211_tx_info at hw_scan_work") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Link: https://lore.kernel.org/r/20220505230421.5f139f9de173.I77ae111a28f7c0e9fd1ebcee7f39dbec5c606770@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
* can: grcan: only use the NAPI poll budget for RXAndreas Larsson2022-05-151-15/+7
| | | | | | | | | | | | | | | | | commit 2873d4d52f7c52d60b316ba6c47bd7122b5a9861 upstream. The previous split budget between TX and RX made it return not using the entire budget but at the same time not having calling called napi_complete. This sometimes led to the poll to not be called, and at the same time having TX and RX interrupts disabled resulting in the driver getting stuck. Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores") Link: https://lore.kernel.org/all/20220429084656.29788-4-andreas@gaisler.com Cc: stable@vger.kernel.org Signed-off-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* can: grcan: grcan_probe(): fix broken system id check for errata workaround ↵Andreas Larsson2022-05-151-5/+11
| | | | | | | | | | | | | | | | needs commit 1e93ed26acf03fe6c97c6d573a10178596aadd43 upstream. The systemid property was checked for in the wrong place of the device tree and compared to the wrong value. Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores") Link: https://lore.kernel.org/all/20220429084656.29788-3-andreas@gaisler.com Cc: stable@vger.kernel.org Signed-off-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* nfp: bpf: silence bitwise vs. logical OR warningNathan Chancellor2022-05-151-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 8a64ef042eab8a6cec04a6c79d44d1af79b628ca upstream. A new warning in clang points out two places in this driver where boolean expressions are being used with a bitwise OR instead of a logical one: drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical] reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ || drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: note: cast one or both operands to int to silence this warning drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical] reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ || drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: note: cast one or both operands to int to silence this warning 2 errors generated. The motivation for the warning is that logical operations short circuit while bitwise operations do not. In this case, it does not seem like short circuiting is harmful so implement the suggested fix of changing to a logical operation to fix the warning. Link: https://github.com/ClangBuiltLinux/linux/issues/1479 Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20211018193101.2340261-1-nathan@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* smsc911x: allow using IRQ0Sergey Shtylyov2022-05-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | commit 5ef9b803a4af0f5e42012176889b40bb2a978b18 upstream. The AlphaProject AP-SH4A-3A/AP-SH4AD-0A SH boards use IRQ0 for their SMSC LAN911x Ethernet chip, so the networking on them must have been broken by commit 965b2aa78fbc ("net/smsc911x: fix irq resource allocation failure") which filtered out 0 as well as the negative error codes -- it was kinda correct at the time, as platform_get_irq() could return 0 on of_irq_get() failure and on the actual 0 in an IRQ resource. This issue was fixed by me (back in 2016!), so we should be able to fix this driver to allow IRQ0 usage again... When merging this to the stable kernels, make sure you also merge commit e330b9a6bb35 ("platform: don't return 0 from platform_get_irq[_byname]() on error") -- that's my fix to platform_get_irq() for the DT platforms... Fixes: 965b2aa78fbc ("net/smsc911x: fix irq resource allocation failure") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Link: https://lore.kernel.org/r/656036e4-6387-38df-b8a7-6ba683b16e63@omp.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.46.0) at 2025-04-24 19:50:34 +0000