| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
| |
Some trivial spelling mistakes which caught my eye during the
review of the code.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Link: https://lore.kernel.org/r/20210409074223.32480-1-salil.mehta@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The ethernet frame length is calculated incorrectly. Depending on
the value of RX_HEAD_PADDING, this may result in ethernet frames
that are too short (cut off at the end), or too long (garbage added
to the end).
Fix by calculating the ethernet frame length correctly. For added
clarity, use the ETH_FCS_LEN constant in the calculation.
Many thanks to Heiner Kallweit for suggesting this solution.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 3e21a10fdea3 ("lan743x: trim all 4 bytes of the FCS; not just 2")
Link: https://lore.kernel.org/lkml/20210408172353.21143-1-TheSven73@gmail.com/
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Link: https://lore.kernel.org/r/20210409003904.8957-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Fixes: 3e6fdeb28f4c33 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
Cc: stable@vger.kernel.org
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-04-08
This series contains updates to i40e and ice drivers.
Grzegorz fixes the ordering of parameters to i40e_aq_get_phy_register()
which is causing incorrect information to be reported.
Arkadiusz fixes various sparse issues reported on the i40e driver.
Yongxin Liu fixes a memory leak with aRFS following resume from suspend
for ice driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In ice_suspend(), ice_clear_interrupt_scheme() is called, and then
irq_free_descs() will be eventually called to free irq and its descriptor.
In ice_resume(), ice_init_interrupt_scheme() is called to allocate new
irqs. However, in ice_rebuild_arfs(), struct irq_glue and struct cpu_rmap
maybe cannot be freed, if the irqs that released in ice_suspend() were
reassigned to other devices, which makes irq descriptor's affinity_notify
lost.
So call ice_free_cpu_rx_rmap() before ice_clear_interrupt_scheme(), which
can make sure all irq_glue and cpu_rmap can be correctly released before
corresponding irq and descriptor are released.
Fix the following memory leak.
unreferenced object 0xffff95bd951afc00 (size 512):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
18 00 00 00 18 00 18 00 70 fc 1a 95 bd 95 ff ff ........p.......
00 00 ff ff 01 00 ff ff 02 00 ff ff 03 00 ff ff ................
backtrace:
[<0000000072e4b914>] __kmalloc+0x336/0x540
[<0000000054642a87>] alloc_cpu_rmap+0x3b/0xb0
[<00000000f220deec>] ice_set_cpu_rx_rmap+0x6a/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
unreferenced object 0xffff95bd81b0a2a0 (size 96):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
38 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 8...............
b0 a2 b0 81 bd 95 ff ff b0 a2 b0 81 bd 95 ff ff ................
backtrace:
[<00000000582dd5c5>] kmem_cache_alloc_trace+0x31f/0x4c0
[<000000002659850d>] irq_cpu_rmap_add+0x25/0xe0
[<00000000495a3055>] ice_set_cpu_rx_rmap+0xb4/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
Fixes: 769c500dcc1e ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Set proper return values inside error checking if-statements.
Previously following warning was produced when compiling against sparse.
i40e_main.c:15162 i40e_init_recovery_mode() warn: missing error code 'err'
Fixes: 4ff0ee1af0169 ("i40e: Introduce recovery mode support")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Remove vsi->netdev->name from the trace.
This is redundant information. With the devinfo trace, the adapter
is already identifiable.
Previously following error was produced when compiling against sparse.
i40e_main.c:2571 i40e_sync_vsi_filters() error:
we previously assumed 'vsi->netdev' could be null (see line 2323)
Fixes: b603f9dc20af ("i40e: Log info when PF is entering and leaving Allmulti mode.")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Init pointer with NULL in default switch case statement.
Previously the error was produced when compiling against sparse.
i40e_debugfs.c:582 i40e_dbg_dump_desc() error: uninitialized symbol 'ring'.
Fixes: 44ea803e2fa7 ("i40e: introduce new dump desc XDP command")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Remove error handling through pointers. Instead use plain int
to return value from i40e_run_xdp(...).
Previously:
- sparse errors were produced during compilation:
i40e_txrx.c:2338 i40e_run_xdp() error: (-2147483647) too low for ERR_PTR
i40e_txrx.c:2558 i40e_clean_rx_irq() error: 'skb' dereferencing possible ERR_PTR()
- sk_buff* was used to return value, but it has never had valid
pointer to sk_buff. Returned value was always int handled as
a pointer.
Fixes: 0c8493d90b6b ("i40e: add XDP support for pass and drop actions")
Fixes: 2e6893123830 ("i40e: split XDP_TX tail and XDP_REDIRECT map flushing")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Change parameters order in aq_get_phy_register() due to wrong
statistics in PHY reported by ethtool. Previously all PHY statistics were
exactly the same for all interfaces
Now statistics are reported correctly - different for different interfaces
Fixes: 0514db37dd78 ("i40e: Extend PHY access with page change flag")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|/
|
|
|
|
|
|
|
|
| |
cfg80211_inform_bss expects to receive a TSF value, but is given the
time since boot in nanoseconds. TSF values are expected to be at
microsecond scale rather than nanosecond scale.
Signed-off-by: A. Cody Schuffelen <schuffelen@google.com>
Link: https://lore.kernel.org/r/20210318200419.1421034-1-schuffelen@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Multiple ttys try to claim the same the minor number causing a double
unregistration of the same device. The first unregistration succeeds
but the next one results in a null-ptr-deref.
The get_free_serial_index() function returns an available minor number
but doesn't assign it immediately. The assignment is done by the caller
later. But before this assignment, calls to get_free_serial_index()
would return the same minor number.
Fix this by modifying get_free_serial_index to assign the minor number
immediately after one is found to be and rename it to obtain_minor()
to better reflect what it does. Similary, rename set_serial_by_index()
to release_minor() and modify it to free up the minor number of the
given hso_serial. Every obtain_minor() should have corresponding
release_minor() call.
Fixes: 72dc1c096c705 ("HSO: add option hso driver")
Reported-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Tested-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.12
Third, and last, set of fixes for v5.12. Small fixes, iwlwifi having
most of them. brcmfmac regression caused by cfg80211 changes is the
most important here.
iwlwifi
* fix a lockdep warning
* fix regulatory feature detection in certain firmware versions
* new hardware support
* fix lockdep warning
* mvm: fix beacon protection checks
mt76
* mt7921: fix airtime reporting
brcmfmac
* fix a deadlock regression
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Unfortunately, since beacon protection isn't fully available
yet, we didn't notice that there are problems with it and
that the replay detection isn't working correctly. We were
relying only on mac80211, since iwl_mvm_rx_crypto() exits
when !ieee80211_has_protected(), which is of course true for
protected (but not encrypted) management frames.
Fix this to properly detect protected (but not encrypted)
management frames and handle them - we continue to only care
about beacons since for others everything can and will be
checked in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: b1fdc2505abc ("iwlwifi: mvm: advertise BIGTK client support if available")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.23c990843369.I09c262a8f6f9852cc8f513cdcb31a7f8f87dd8af@changeid
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The mutex is already locked in iwl_mvm_mac_start.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Fixes: 21254908cbe9 ("iwlwifi: mvm: add RFI-M support")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.703288ea058d.I82a0312389032d07c3b478bef3e938e06bfa7df6@changeid
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We have a new type of device that has a different MAC ID, but is
otherwise identical to So devices. Add rules to match this new ID
accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.4feea3560def.I2b6ef794c2073a18779dd40fb53f8c942d1ab42d@changeid
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Since we now call iwl_notification_wait_notify() from the
NAPI poll in soft-IRQ, we get a (valid) lockdep complaint
that we could get a deadlock by taking the spinlock from
sleeping context and then getting the soft-IRQ that also
tries to take it (in NAPI polling).
Fix this by disabling soft-IRQs for this lock.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 25edc8f259c7 ("iwlwifi: pcie: properly implement NAPI")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.c3b2e3d6b58b.Ic56f351d04674df70567bab0269cba91bdbc853c@changeid
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add this specific Samsung AX201 sku to driver so it can be
detected and initialized successfully.
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.30b622037714.Id9fd709cf1c8261c097bbfd7453f6476077dcafc@changeid
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
As the context info gen3 code is only called for >=AX210 devices
(from iwl_trans_pcie_gen2_start_fw()) the code there to set LTR
on 22000 devices cannot actually do anything (22000 < AX210).
Fix this by moving the LTR code to iwl_trans_pcie_gen2_start_fw()
where it can handle both devices. This then requires that we kick
the firmware only after that rather than doing it from the context
info code.
Note that this again had a dead branch in gen3 code, which I've
removed here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: ed0022da8bd9 ("iwlwifi: pcie: set LTR on more devices")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.675486178ed1.Ib61463aba6920645059e366dcdca4c4c77f0ff58@changeid
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When version 2 of the regulatory capability flags API was implemented,
the flag to disable 11ax was defined as bit 13, but this was later
changed and the bit remained as bit 10, like in version 1. This was
never changed in the driver, so we were checking for the wrong bit in
newer devices. Fix it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: e27c506a985c ("iwlwifi: regulatory: regulatory capabilities api change")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.6d28516b59cd.Id0248d5e4662695254f49ce37b0268834ed52918@changeid
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit a05829a7222e ("cfg80211: avoid holding the RTNL when calling the
driver") replaced the rtnl_lock parameter passed to various brcmf
functions with just lock, because since that commit it is not just
about the rtnl_lock but also about the wiphy_lock .
During this search/replace the "if (!rtnl_locked)" check in brcmfmac/p2p.c
was accidentally replaced with "if (locked)", dropping the inversion of
the check. This causes the code to now call rtnl_lock() while already
holding the lock, causing a deadlock.
Add back the "!" to the if-condition to fix this.
Cc: Johannes Berg <johannes.berg@intel.com>
Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210313143635.109154-1-hdegoede@redhat.com
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fix {tx,rx}_airtime reporting for mt7921 driver. Wrong register definitions
trigger a tx hangs before resetting airtime stats.
Fixes: 163f4d22c118d ("mt76: mt7921: add MAC support")
Tested-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/c05333be0e3e85a50a71bb2de81034fe425e3701.1615284335.git.lorenzo@kernel.org
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
It's possible for iwl_pcie_enqueue_hcmd() to be called with hard IRQs
disabled (e.g. from LED core). We can't enable BHs in such a situation.
Turn the unconditional BH-enable/BH-disable code into
hardirq-disable/conditional-enable.
This fixes the warning below.
WARNING: CPU: 1 PID: 1139 at kernel/softirq.c:178 __local_bh_enable_ip+0xa5/0xf0
CPU: 1 PID: 1139 Comm: NetworkManager Not tainted 5.12.0-rc1-00004-gb4ded168af79 #7
Hardware name: LENOVO 20K5S22R00/20K5S22R00, BIOS R0IET38W (1.16 ) 05/31/2017
RIP: 0010:__local_bh_enable_ip+0xa5/0xf0
Code: f7 69 e8 ee 23 14 00 fb 66 0f 1f 44 00 00 65 8b 05 f0 f4 f7 69 85 c0 74 3f 48 83 c4 08 5b c3 65 8b 05 9b fe f7 69 85 c0 75 8e <0f> 0b eb 8a 48 89 3c 24 e8 4e 20 14 00 48 8b 3c 24 eb 91 e8 13 4e
RSP: 0018:ffffafd580b13298 EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000201 RCX: 0000000000000000
RDX: 0000000000000003 RSI: 0000000000000201 RDI: ffffffffc1272389
RBP: ffff96517ae4c018 R08: 0000000000000001 R09: 0000000000000000
R10: ffffafd580b13178 R11: 0000000000000001 R12: ffff96517b060000
R13: 0000000000000000 R14: ffffffff80000000 R15: 0000000000000001
FS: 00007fc604ebefc0(0000) GS:ffff965267480000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055fb3fef13b2 CR3: 0000000109112004 CR4: 00000000003706e0
Call Trace:
? _raw_spin_unlock_bh+0x1f/0x30
iwl_pcie_enqueue_hcmd+0x5d9/0xa00 [iwlwifi]
iwl_trans_txq_send_hcmd+0x6c/0x430 [iwlwifi]
iwl_trans_send_cmd+0x88/0x170 [iwlwifi]
? lock_acquire+0x277/0x3d0
iwl_mvm_send_cmd+0x32/0x80 [iwlmvm]
iwl_mvm_led_set+0xc2/0xe0 [iwlmvm]
? led_trigger_event+0x46/0x70
led_trigger_event+0x46/0x70
ieee80211_do_open+0x5c5/0xa20 [mac80211]
ieee80211_open+0x67/0x90 [mac80211]
__dev_open+0xd4/0x150
__dev_change_flags+0x19e/0x1f0
dev_change_flags+0x23/0x60
do_setlink+0x30d/0x1230
? lock_is_held_type+0xb4/0x120
? __nla_validate_parse.part.7+0x57/0xcb0
? __lock_acquire+0x2e1/0x1a50
__rtnl_newlink+0x560/0x910
? __lock_acquire+0x2e1/0x1a50
? __lock_acquire+0x2e1/0x1a50
? lock_acquire+0x277/0x3d0
? sock_def_readable+0x5/0x290
? lock_is_held_type+0xb4/0x120
? find_held_lock+0x2d/0x90
? sock_def_readable+0xb3/0x290
? lock_release+0x166/0x2a0
? lock_is_held_type+0x90/0x120
rtnl_newlink+0x47/0x70
rtnetlink_rcv_msg+0x25c/0x470
? netlink_deliver_tap+0x97/0x3e0
? validate_linkmsg+0x350/0x350
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x1b2/0x280
netlink_sendmsg+0x336/0x450
sock_sendmsg+0x5b/0x60
____sys_sendmsg+0x1ed/0x250
? copy_msghdr_from_user+0x5c/0x90
___sys_sendmsg+0x88/0xd0
? lock_is_held_type+0xb4/0x120
? find_held_lock+0x2d/0x90
? lock_release+0x166/0x2a0
? __fget_files+0xfe/0x1d0
? __sys_sendmsg+0x5e/0xa0
__sys_sendmsg+0x5e/0xa0
? lockdep_hardirqs_on_prepare+0xd9/0x170
do_syscall_64+0x33/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fc605c9572d
Code: 28 89 54 24 1c 48 89 74 24 10 89 7c 24 08 e8 da ee ff ff 8b 54 24 1c 48 8b 74 24 10 41 89 c0 8b 7c 24 08 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 33 44 89 c7 48 89 44 24 08 e8 2e ef ff ff 48
RSP: 002b:00007fffc83789f0 EFLAGS: 00000293 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 000055ef468570c0 RCX: 00007fc605c9572d
RDX: 0000000000000000 RSI: 00007fffc8378a30 RDI: 000000000000000c
RBP: 0000000000000010 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000293 R12: 0000000000000000
R13: 00007fffc8378b80 R14: 00007fffc8378b7c R15: 0000000000000000
irq event stamp: 170785
hardirqs last enabled at (170783): [<ffffffff9609a8c2>] __local_bh_enable_ip+0x82/0xf0
hardirqs last disabled at (170784): [<ffffffff96a8613d>] _raw_read_lock_irqsave+0x8d/0x90
softirqs last enabled at (170782): [<ffffffffc1272389>] iwl_pcie_enqueue_hcmd+0x5d9/0xa00 [iwlwifi]
softirqs last disabled at (170785): [<ffffffffc1271ec6>] iwl_pcie_enqueue_hcmd+0x116/0xa00 [iwlwifi]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # LLVM/Clang v12.0.0-rc3
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2103021125430.12405@cbobk.fhfr.pm
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Some drivers clear the 'ethtool_link_ksettings' struct in their
get_link_ksettings() callback, before populating it with actual values.
Such drivers will set the new 'link_mode' field to zero, resulting in
user space receiving wrong link mode information given that zero is a
valid value for the field.
Another problem is that some drivers (notably tun) can report random
values in the 'link_mode' field. This can result in a general protection
fault when the field is used as an index to the 'link_mode_params' array
[1].
This happens because such drivers implement their set_link_ksettings()
callback by simply overwriting their private copy of
'ethtool_link_ksettings' struct with the one they get from the stack,
which is not always properly initialized.
Fix these problems by removing 'link_mode' from 'ethtool_link_ksettings'
and instead have drivers call ethtool_params_from_link_mode() with the
current link mode. The function will derive the link parameters (e.g.,
speed) from the link mode and fill them in the 'ethtool_link_ksettings'
struct.
v3:
* Remove link_mode parameter and derive the link parameters in
the driver instead of passing link_mode parameter to ethtool
and derive it there.
v2:
* Introduce 'cap_link_mode_supported' instead of adding a
validity field to 'ethtool_link_ksettings' struct.
[1]
general protection fault, probably for non-canonical address 0xdffffc00f14cc32c: 0000 [#1] PREEMPT SMP KASAN
KASAN: probably user-memory-access in range [0x000000078a661960-0x000000078a661967]
CPU: 0 PID: 8452 Comm: syz-executor360 Not tainted 5.11.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__ethtool_get_link_ksettings+0x1a3/0x3a0 net/ethtool/ioctl.c:446
Code: b7 3e fa 83 fd ff 0f 84 30 01 00 00 e8 16 b0 3e fa 48 8d 3c ed 60 d5 69 8a 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 03
+38 d0 7c 08 84 d2 0f 85 b9
RSP: 0018:ffffc900019df7a0 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff888026136008 RCX: 0000000000000000
RDX: 00000000f14cc32c RSI: ffffffff873439ca RDI: 000000078a661960
RBP: 00000000ffff8880 R08: 00000000ffffffff R09: ffff88802613606f
R10: ffffffff873439bc R11: 0000000000000000 R12: 0000000000000000
R13: ffff88802613606c R14: ffff888011d0c210 R15: ffff888011d0c210
FS: 0000000000749300(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004b60f0 CR3: 00000000185c2000 CR4: 00000000001506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
linkinfo_prepare_data+0xfd/0x280 net/ethtool/linkinfo.c:37
ethnl_default_notify+0x1dc/0x630 net/ethtool/netlink.c:586
ethtool_notify+0xbd/0x1f0 net/ethtool/netlink.c:656
ethtool_set_link_ksettings+0x277/0x330 net/ethtool/ioctl.c:620
dev_ethtool+0x2b35/0x45d0 net/ethtool/ioctl.c:2842
dev_ioctl+0x463/0xb70 net/core/dev_ioctl.c:440
sock_do_ioctl+0x148/0x2d0 net/socket.c:1060
sock_ioctl+0x477/0x6a0 net/socket.c:1177
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:739
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: c8907043c6ac9 ("ethtool: Get link mode in use instead of speed and duplex parameters")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Memory allocated by kvzalloc() should be freed by kvfree().
Fixes: 34ca65352ddf2 ("net/mlx5: E-Switch, Indirect table infrastructur")
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Make sure to modify uplink port to follow only if the uplink_follow
capability is set as required by the HW spec. Failure to do so causes
traffic to the uplink representor net device to cease after switching to
switchdev mode.
Fixes: 7d0314b11cdd ("net/mlx5e: Modify uplink state on interface up/down")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When changing type with TUNSETLINK ioctl command, set tun->dev->addr_len
to match the appropriate type, using new tun_get_addr_len utility function
which returns appropriate address length for given type. Fixes a
KMSAN-found uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=0766d38c656abeace60621896d705743aeefed51
Reported-by: syzbot+001516d86dbe88862cec@syzkaller.appspotmail.com
Diagnosed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently, the VF down state bit is cleared after VF sending
link status request command. There is problem that when VF gets
link status replied from PF, the down state bit may still set
as 1. In this case, the link status replied from PF will be
ignored and always set VF link status to down.
To fix this problem, clear VF down state bit before VF requests
link status.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2021-04-06
this is a pull request of 1 patch for net/master.
The patch is by me and fixes the SPI half duplex support in the
mcp251x CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Some SPI host controllers do not support full-duplex SPI transfers.
The function mcp251x_spi_trans() does a full duplex transfer. It is
used in several places in the driver, where a TX half duplex transfer
is sufficient.
To fix support for half duplex SPI host controllers, this patch
introduces a new function mcp251x_spi_write() and changes all callers
that do a TX half duplex transfer to use mcp251x_spi_write().
Fixes: e0e25001d088 ("can: mcp251x: add support for half duplex controllers")
Link: https://lore.kernel.org/r/20210330100246.1074375-1-mkl@pengutronix.de
Cc: Tim Harvey <tharvey@gateworks.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Reported-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
pci_resource_start() is not a good indicator to determine if a PCI
resource exists or not, since the resource may start at address 0.
This is seen when trying to instantiate the driver in qemu for riscv32
or riscv64.
pci 0000:00:01.0: reg 0x10: [io 0x0000-0x001f]
pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000001f]
...
pcnet32: card has no PCI IO resources, aborting
Use pci_resouce_len() instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Xuan Zhuo reported that commit 3226b158e67c ("net: avoid 32 x truesize
under-estimation for tiny skbs") brought a ~10% performance drop.
The reason for the performance drop was that GRO was forced
to chain sk_buff (using skb_shinfo(skb)->frag_list), which
uses more memory but also cause packet consumers to go over
a lot of overhead handling all the tiny skbs.
It turns out that virtio_net page_to_skb() has a wrong strategy :
It allocates skbs with GOOD_COPY_LEN (128) bytes in skb->head, then
copies 128 bytes from the page, before feeding the packet to GRO stack.
This was suboptimal before commit 3226b158e67c ("net: avoid 32 x truesize
under-estimation for tiny skbs") because GRO was using 2 frags per MSS,
meaning we were not packing MSS with 100% efficiency.
Fix is to pull only the ethernet header in page_to_skb()
Then, we change virtio_net_hdr_to_skb() to pull the missing
headers, instead of assuming they were already pulled by callers.
This fixes the performance regression, but could also allow virtio_net
to accept packets with more than 128bytes of headers.
Many thanks to Xuan Zhuo for his report, and his tests/help.
Fixes: 3226b158e67c ("net: avoid 32 x truesize under-estimation for tiny skbs")
Reported-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://www.spinics.net/lists/netdev/msg731397.html
Co-Developed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/ /
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In bcm4908_enet_dma_alloc, if callee bcm4908_dma_alloc_buf_descs() failed,
it will free the ring->cpu_addr by dma_free_coherent() and return error.
Then bcm4908_enet_dma_free() will be called, and free the same cpu_addr
by dma_free_coherent() again.
My patch set ring->cpu_addr to NULL after it is freed in
bcm4908_dma_alloc_buf_descs() to avoid the double free.
Fixes: 4feffeadbcb2e ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Code to defer the reset(which caps the frequency of the reset) schedules the
timer and returns. Hence, following 'else-if' looks un-necessary.
Fixes: 9de0b86f6444 ("net: hns3: Prevent to request reset frequently")
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This removes the left over check and assignment which is no longer used
anywhere in the function and should have been removed as part of the
below mentioned patch.
Fixes: 012fcb52f67c ("net: hns3: activate reset timer when calling reset_event")
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Restore CMP screener registers on resume path.
Fixes: c1e85c6ce57ef ("net: macb: save/restore the remaining registers and features")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-04-01
This series contains updates to i40e driver only.
Arkadiusz fixes warnings for inconsistent indentation.
Magnus fixes an issue on xsk receive where single packets over time
are batched rather than received immediately.
Eryk corrects warnings and reporting of veb-stats.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
If veb-stats was enabled, the ethtool stats triggered a warning
due to invalid size: 'unexpected stat size for veb.tc_%u_tx_packets'.
This was due to an incorrect structure definition for the statistics.
Structures and functions have been improved in line with requirements
for the presentation of statistics, in particular for the functions:
'i40e_add_ethtool_stats' and 'i40e_add_stat_strings'.
Fixes: 1510ae0be2a4 ("i40e: convert VEB TC stats to use an i40e_stats array")
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fix so that single packets are received immediately instead of in
batches of 8. If you sent 1 pps to a system, you received 8 packets
every 8 seconds instead of 1 packet every second. The problem behind
this was that the work_done reporting from the Tx part of the driver
was broken. The work_done reporting in i40e controls not only the
reporting back to the napi logic but also the setting of the interrupt
throttling logic. When Tx or Rx reports that it has more to do,
interrupts are throttled or coalesced and when they both report that
they are done, interrupts are armed right away. If the wrong work_done
value is returned, the logic will start to throttle interrupts in a
situation where it should have just enabled them. This leads to the
undesired batching behavior seen in user-space.
Fix this by returning the correct boolean value from the Tx xsk
zero-copy path. Return true if there is nothing to do or if we got
fewer packets to process than we asked for. Return false if we got as
many packets as the budget since there might be more packets we can
process.
Fixes: 3106c580fb7c ("i40e: Use batched xsk Tx interfaces to increase performance")
Reported-by: Sreedevi Joshi <sreedevi.joshi@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fixed new static analysis findings:
"warn: inconsistent indenting" - introduced lately,
reported with lkp and smatch build.
Fixes: 4b208eaa8078 ("i40e: Add init and default config of software based DCB")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
syzbot reported memory leak in peak_usb.
The problem was in case of failure after calling
->dev_init()[2] in peak_usb_create_dev()[1]. The data
allocated int dev_init() wasn't freed, so simple
->dev_free() call fix this problem.
backtrace:
[<0000000079d6542a>] kmalloc include/linux/slab.h:552 [inline]
[<0000000079d6542a>] kzalloc include/linux/slab.h:682 [inline]
[<0000000079d6542a>] pcan_usb_fd_init+0x156/0x210 drivers/net/can/usb/peak_usb/pcan_usb_fd.c:868 [2]
[<00000000c09f9057>] peak_usb_create_dev drivers/net/can/usb/peak_usb/pcan_usb_core.c:851 [inline] [1]
[<00000000c09f9057>] peak_usb_probe+0x389/0x490 drivers/net/can/usb/peak_usb/pcan_usb_core.c:949
Reported-by: syzbot+91adee8d9ebb9193d22d@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/ /
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
syzbot reported memory leak in atusb_probe()[1].
The problem was in atusb_alloc_urbs().
Since urb is anchored, we need to release the reference
to correctly free the urb
backtrace:
[<ffffffff82ba0466>] kmalloc include/linux/slab.h:559 [inline]
[<ffffffff82ba0466>] usb_alloc_urb+0x66/0xe0 drivers/usb/core/urb.c:74
[<ffffffff82ad3888>] atusb_alloc_urbs drivers/net/ieee802154/atusb.c:362 [inline][2]
[<ffffffff82ad3888>] atusb_probe+0x158/0x820 drivers/net/ieee802154/atusb.c:1038 [1]
Reported-by: syzbot+28a246747e0a465127f3@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
XSK wakeup flow triggers an IRQ by posting a NOP WQE and hitting
the doorbell on the async ICOSQ.
It maintains its state so that it doesn't issue another NOP WQE
if it has an outstanding one already.
For this flow to work properly, the NOP post must not fail.
Make sure to reserve room for the NOP WQE in all WQE posts to the
async ICOSQ.
Fixes: 8d94b590f1e4 ("net/mlx5e: Turn XSK ICOSQ into a general asynchronous one")
Fixes: 1182f3659357 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Fixes: 0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Current algorithm for encap keys is legacy from initial vxlan
implementation and doesn't take into account all possible fields of a
tunnel. For example, for a Geneve tunnel, which may have additional TLV
options, they are ignored when comparing encap keys and a rule can be
attached to an incorrect encap entry.
Fix that by introducing encap_info_equal() operation in
struct mlx5e_tc_tunnel. Geneve tunnel type uses custom implementation,
which extends generic algorithm and considers options if they are set.
Fixes: 7f1a546e3222 ("net/mlx5e: Consider tunnel type for encap contexts")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Calculating the number of compeltion EQs based on the number of
available IRQ vectors doesn't work now that all async EQs share one IRQ.
Thus the max number of EQs can be exceeded on systems with more than
approximately 256 CPUs. Take this into account when calculating the
number of available completion EQs.
Fixes: 81bfa206032a ("net/mlx5: Use a single IRQ for all async EQs")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Some TLS RX counters increment per socket/connection, and are not
protected against parallel modifications from several cores.
Switch them to atomic counters by taking them out of the RQ stats into
the global atomic TLS stats.
In this patch, we touch 'rx_tls_ctx/del' that count the number of
device-offloaded RX TLS connections added/deleted.
These counters are updated in the add/del callbacks, out of the fast
data-path.
This change is not needed for counters that increment only in NAPI
context, as they are protected by the NAPI mechanism.
Keep them as tls_* counters under 'struct mlx5e_rq_stats'.
Fixes: 76c1e1ac2aae ("net/mlx5e: kTLS, Add kTLS RX stats")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Some TLS TX counters increment per socket/connection, and are not
protected against parallel modifications from several cores.
Switch them to atomic counters by taking them out of the SQ stats into
the global atomic TLS stats.
In this patch, we touch a single counter 'tx_tls_ctx' that counts the
number of device-offloaded TX TLS connections added.
Now that this counter can be increased without the for having the SQ
context in hand, move it to the mlx5e_ktls_add_tx() callback where it
really belongs, out of the fast data-path.
This change is not needed for counters that increment only in NAPI
context or under the TX lock, as they are already protected.
Keep them as tls_* counters under 'struct mlx5e_sq_stats'.
Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Create send to vport miss group was added in order to support traffic
recirculation to root table with metadata source rewrite.
This group is created also in case source rewrite isn't supported.
Fixed by creating send to vport miss group only if source rewrite is
supported by FW.
Fixes: 8e404fefa58b ("net/mlx5e: Match recirculated packet miss in slow table using reg_c1")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Use connector_type read from PTYS register when it's valid, based on
corresponding capability bit.
Fixes: 5b4793f81745 ("net/mlx5e: Add support for reading connector type from PTYS")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|