summaryrefslogtreecommitdiffstats
path: root/drivers/remoteproc/qcom_q6v5_mss.c
Commit message (Collapse)AuthorAgeFilesLines
* remoteproc: qcom: q6v5-mss: Add support for SDM630/636/660Alexey Minnekhanov2023-07-151-2/+49
| | | | | | | | | | | | | | | | | | | | | | | Snapdragon 630/660 modem subsystem is similar to one in MSM8998 and can almost reuse it's reset sequence. Downstream sources call this q6v5 version "qdsp6v62-1-5" and its code path has additional checks for QDSP6v55_BHS_EN_REST_ACK status [2]. Inspiration is taken from Konrad Dybcio's work in [1], but reworked to use common code path with MSM8996/8998, instead of completely separate "if" block for SDM660. [1] https://github.com/SoMainline/linux/commit/7dd6dd9b936dc8d6c1f1abe299e5b065c33741e8 [2] https://github.com/MiCode/Xiaomi_Kernel_OpenSource/blob/lavender-q-oss/drivers/soc/qcom/pil-q6v5.c#L393 Co-developed-by: Konrad Dybcio <konradybcio@gmail.com> Signed-off-by: Konrad Dybcio <konradybcio@gmail.com> Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20230621175046.61521-2-alexeymin@postmarketos.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
* remoteproc: qcom: Use of_reserved_mem_lookup()Stephan Gerhold2023-07-151-13/+20
| | | | | | | | | | | | | | | | | | | | | | | | Reserved memory can be either looked up using the generic function of_address_to_resource() or using the special of_reserved_mem_lookup(). The latter has the advantage that it ensures that the referenced memory region was really reserved and is not e.g. status = "disabled". of_reserved_mem also supports allocating reserved memory dynamically at boot time. This works only when using of_reserved_mem_lookup() since there won't be a fixed address in the device tree. Switch the code to use of_reserved_mem_lookup(), similar to qcom_q6v5_wcss.c which is using it already. There is no functional difference for static reserved memory allocations. While at it this also adds two missing of_node_put() calls in qcom_q6v5_pas.c. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Tested-by: Caleb Connolly <caleb.connolly@linaro.org> # SDM845 Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org> Link: https://lore.kernel.org/r/20230710-rproc-of-rmem-v3-1-eea7f0a33590@gerhold.net Signed-off-by: Bjorn Andersson <andersson@kernel.org>
* remoteproc: Explicitly include correct DT includesRob Herring2023-07-151-1/+2
| | | | | | | | | | | | | | | The DT of_device.h and of_platform.h date back to the separate of_platform_bus_type before it as merged into the regular platform bus. As part of that merge prepping Arm DT support 13 years ago, they "temporarily" include each other. They also include platform_device.h and of.h. As a result, there's a pretty much random mix of those include files used throughout the tree. In order to detangle these headers and replace the implicit includes with struct declarations, users need to explicitly include the correct includes. Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20230714174935.4063513-1-robh@kernel.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
* remoteproc: qcom_q6v5_mss: Convert to platform remove callback returning voidUwe Kleine-König2023-05-091-4/+2
| | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is (mostly) ignored and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org> Link: https://lore.kernel.org/r/20230504194453.1150368-11-u.kleine-koenig@pengutronix.de Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
* Merge tag 'rproc-v6.4' of ↵Linus Torvalds2023-04-251-4/+4
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux Pull remoteproc updates from Bjorn Andersson: - Unnecessary type casts from the 'void *' rproc->priv pointer are dropped throughout the subsystem. - A kernel-doc error is corrected in the Mediatek SCPI IPI implementation - The firmware loading onto the IMX DSP remote processors is reworked to avoid non-32bit memory operations. A module parameter is introduced to assist development of firmware without communication abilities in place. Error paths in imx_dsp_rproc_mbox_alloc() is cleaned up - The cluster configuration handling in the TI K3 R5 driver is corrected and support for the single-R5 core found in the TI AM62x SoC family is introduced - The TI PRU driver device- to virtual-address translation is updated to avoid compiler warning about the unsigned device-address always being larger than 0 - The ST remoteproc driver is transitioned to use of_property_present() - Issues with kicks arriving after the STM32 remote processor has been shut down are mitigated by checking the processor's state before handling them. - Support for mailbox channels for communication with the remote processors are added to the Xilinx R5 remoteproc driver. The naming of carveouts are corrected and their parsing is reworked. For this a couple of fixes targeting the mailbox subsystem are picked up here as well. - Reference counting of of_nodes are corrected in the ST, STM32, RCAR and IMX remoteproc drivers * tag 'rproc-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (24 commits) remoteproc: st: Use of_property_present() for testing DT property presence dt-bindings: remoteproc: Drop unneeded quotes remoteproc: imx_dsp_rproc: Fix kernel test robot sparse warning remoteproc: imx_dsp_rproc: Improve exception handling in imx_dsp_rproc_mbox_alloc() remoteproc: pru: Remove always true check positive unsigned value dt-bindings: remoteproc: stm32-rproc: Typo fix remoteproc: stm32_rproc: Add mutex protection for workqueue remoteproc: Remove unnecessary (void*) conversions remoteproc: imx_dsp_rproc: Call of_node_put() on iteration error remoteproc: imx_rproc: Call of_node_put() on iteration error remoteproc: rcar_rproc: Call of_node_put() on iteration error remoteproc: st: Call of_node_put() on iteration error remoteproc: stm32: Call of_node_put() on iteration error remoteproc: k3-r5: Use separate compatible string for TI AM62x SoC family dt-bindings: remoteproc: ti: Add new compatible for AM62 SoC family remoteproc: k3-r5: Simplify cluster mode setting usage remoteproc/mtk_scpi_ipi: Fix one kernel-doc comment remoteproc: xilinx: Add mailbox channels for rpmsg drivers: remoteproc: xilinx: Fix carveout names mailbox: zynqmp: Fix typo in IPI documentation ...
| * remoteproc: Remove unnecessary (void*) conversionsYu Zhe2023-04-031-4/+4
| | | | | | | | | | | | | | | | | | Pointer variables of void * type do not require type cast. Signed-off-by: Yu Zhe <yuzhe@nfschina.com> Link: https://lore.kernel.org/r/20230328024907.29791-1-yuzhe@nfschina.com [Fixed merge conflict in xlnx_r5_remoteproc.c] Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
* | firmware: qcom_scm: Use fixed width src vm bitmapElliot Berman2023-03-151-4/+4
|/ | | | | | | | | | | | | The maximum VMID for assign_mem is 63. Use a u64 to represent this bitmap instead of architecture-dependent "unsigned int" which varies in size on 32-bit and 64-bit platforms. Acked-by: Kalle Valo <kvalo@kernel.org> (ath10k) Tested-by: Gokul krishna Krishnakumar <quic_gokukris@quicinc.com> Signed-off-by: Elliot Berman <quic_eberman@quicinc.com> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230213181832.3489174-1-quic_eberman@quicinc.com
* Merge tag 'soc-drivers-6.3' of ↵Linus Torvalds2023-02-271-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC driver updates from Arnd Bergmann: "As usual, there are lots of minor driver changes across SoC platforms from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung. These usually add support for additional chip variations in existing drivers, but also add features or bugfixes. The SCMI firmware subsystem gains a unified raw userspace interface through debugfs, which can be used for validation purposes. Newly added drivers include: - New power management drivers for StarFive JH7110, Allwinner D1 and Renesas RZ/V2M - A driver for Qualcomm battery and power supply status - A SoC device driver for identifying Nuvoton WPCM450 chips - A regulator coupler driver for Mediatek MT81xxv" * tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits) power: supply: Introduce Qualcomm PMIC GLINK power supply soc: apple: rtkit: Do not copy the reg state structure to the stack soc: sunxi: SUN20I_PPU should depend on PM memory: renesas-rpc-if: Remove redundant division of dummy soc: qcom: socinfo: Add IDs for IPQ5332 and its variant dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1 firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/ MAINTAINERS: Update qcom CPR maintainer entry dt-bindings: firmware: document Qualcomm SM8550 SCM dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants soc: qcom: socinfo: Add support for new field in revision 17 soc: qcom: smd-rpm: Add IPQ9574 compatible soc: qcom: pmic_glink: remove redundant calculation of svid soc: qcom: stats: Populate all subsystem debugfs files dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies soc: qcom: pmic_glink: Introduce altmode support ...
| * firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/Elliot Berman2023-02-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Move include/linux/qcom_scm.h to include/linux/firmware/qcom/qcom_scm.h. This removes 1 of a few remaining Qualcomm-specific headers into a more approciate subdirectory under include/. Suggested-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Elliot Berman <quic_eberman@quicinc.com> Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com> Acked-by: Mukesh Ojha <quic_mojha@quicinc.com> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230203210956.3580811-1-quic_eberman@quicinc.com
* | remoteproc: qcom_q6v5_mss: Use a carveout to authenticate modem headersSibi Sankar2023-01-181-6/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Any access to the dynamically allocated metadata region by the application processor after assigning it to the remote Q6 will result in a XPU violation. Fix this by replacing the dynamically allocated memory region with a no-map carveout and unmap the modem metadata memory region before passing control to the remote Q6. Reported-and-tested-by: Amit Pundir <amit.pundir@linaro.org> Fixes: 6c5a9dc2481b ("remoteproc: qcom: Make secure world call for mem ownership switch") Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230117085840.32356-7-quic_sibis@quicinc.com
* | Revert "remoteproc: qcom_q6v5_mss: map/unmap metadata region before/after use"Christoph Hellwig2023-01-181-32/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit fc156629b23a21181e473e60341e3a78af25a1d4. This commit manages to do three API violations at once: - dereference the return value of dma_alloc_attrs with the DMA_ATTR_NO_KERNEL_MAPPING mapping, which is clearly forbidden and will do the wrong thing on various dma mapping implementations. The fact that dma-direct uses a struct page as a cookie is an undocumented implementation detail - include dma-map-ops.h and use pgprot_dmacoherent despite a clear comment documenting that this is not acceptable - use of the VM_DMA_COHERENT for something that is not the dma-mapping code - use of VM_FLUSH_RESET_PERMS for vmap, while it is only supported for vmalloc Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230117085840.32356-6-quic_sibis@quicinc.com
* | remoteproc: qcom: q6v5-mss: Add modem support on MSM8953Sireesh Kodali2022-12-271-2/+53
| | | | | | | | | | | | | | | | | | | | | | The modem on the MSM8953 platform is similar to the modem on the MSM8996 platform in terms of set up. It differs primarily in that TZ needs to be informed of the modem start address and pas_id. Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com> Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20220908182433.466908-8-stephan.gerhold@kernkonzept.com
* | remoteproc: qcom: q6v5-mss: Add support for MSM8909Stephan Gerhold2022-12-271-33/+90
|/ | | | | | | | | | | | | | | | | Port the initialization sequence necessary for booting the modem remote processor on the MSM8909 SoC from Qualcomm's msm-3.10 release [1]. The sequence is actually similar to the existing one for MSM8996 and MSM8998 except that there is no separate QDSP6SS_MEM_PWR_CTL register and most of the "memories" are enabled at once instead of sequentially. To reuse the existing code just insert some if statements where needed and add a configuration similar to the one from MSM8916. [1]: https://git.codelinaro.org/clo/la/kernel/msm-3.10/-/commit/56dcedc8dac8abff6b007f76a29430b2d0a44704 Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20220908182433.466908-6-stephan.gerhold@kernkonzept.com
* remoteproc: qcom: q6v5-mss: add powerdomains to MSM8996 configDmitry Baryshkov2022-07-181-0/+5
| | | | | | | | | | MSM8996 follows the rest of MSS devices and requires a vote on MX and CX power domains. Add corresponding entry to the device data. Fixes: 4760a896be88 ("remoteproc: q6v5-mss: Vote for rpmh power domains") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220704162202.819051-1-dmitry.baryshkov@linaro.org
* remoteproc: qcom_q6v5: Introduce panic handler for MSSSibi Sankar2022-07-181-0/+8
| | | | | | | | | | Make the MSS q6v5 remoteproc drivers implement the panic handler that will invoke a stop to prepare the remoteprocs for post mortem debugging. Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/1653396335-6295-3-git-send-email-quic_sibis@quicinc.com
* remoteproc: qcom_q6v5_mss: Update MBA log infoSibi Sankar2022-07-181-0/+3
| | | | | | | | | | Update MBA text logs location/size in IMEM to aid tools extract them after ramdump collection. The size of the MBA text logs is pre-determined and limited to 4K. Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/1653396335-6295-2-git-send-email-quic_sibis@quicinc.com
* remoteproc: qcom_q6v5_mss: map/unmap metadata region before/after useSibi Sankar2022-07-181-6/+32
| | | | | | | | | | | | | | The application processor accessing the dynamically assigned metadata region after assigning it to the remote Q6 would lead to an XPU violation. Fix this by un-mapping the metadata region post firmware header copy. The metadata region is freed only after the modem Q6 is done with fw header authentication. Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/1652248625-990-1-git-send-email-quic_sibis@quicinc.com
* Merge tag 'rproc-v5.18' of ↵Linus Torvalds2022-03-301-4/+15
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux Pull remoteproc updates from Bjorn Andersson: "In the remoteproc core, it's now possible to mark the sysfs attributes read only on a per-instance basis, which is then used by the TI wkup M3 driver. Also, the rproc_shutdown() interface propagates errors to the caller and an array underflow is fixed in the debugfs interface. The rproc_da_to_va() API is moved to the public API to allow e.g. child rpmsg devices to acquire pointers to memory shared with the remote processor. The TI K3 R5F and DSP drivers gains support for attaching to instances already started by the bootloader, aka IPC-only mode. The Mediatek remoteproc driver gains support for the MT8186 SCP. The driver's probe function is reordered and moved to use the devres version of rproc_alloc() to save a few gotos. The driver's probe function is also transitioned to use dev_err_probe() to provide better debug support. Support for the Qualcomm SC7280 Wireless Subsystem (WPSS) is introduced. The Hexagon based remoteproc drivers gains support for voting for interconnect bandwidth during launch of the remote processor. The modem subsystem (MSS) driver gains support for probing the BAM-DMUX driver, which provides the network interface towards the modem on a set of older Qualcomm platforms. In addition a number a bug fixes are introduces in the Qualcomm drivers. Lastly Qualcomm ADSP DeviceTree binding is converted to YAML format, to allow validation of DeviceTree source files" * tag 'rproc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (22 commits) remoteproc: qcom_q6v5_mss: Create platform device for BAM-DMUX remoteproc: qcom: q6v5_wpss: Add support for sc7280 WPSS dt-bindings: remoteproc: qcom: Add SC7280 WPSS support dt-bindings: remoteproc: qcom: adsp: Convert binding to YAML remoteproc: k3-dsp: Add support for IPC-only mode for all K3 DSPs remoteproc: k3-dsp: Refactor mbox request code in start remoteproc: k3-r5: Add support for IPC-only mode for all R5Fs remoteproc: k3-r5: Refactor mbox request code in start remoteproc: Change rproc_shutdown() to return a status remoteproc: qcom: q6v5: Add interconnect path proxy vote remoteproc: mediatek: Support mt8186 scp dt-bindings: remoteproc: mediatek: Add binding for mt8186 scp remoteproc: qcom_q6v5_mss: Fix some leaks in q6v5_alloc_memory_region remoteproc: qcom_wcnss: Add missing of_node_put() in wcnss_alloc_memory_region remoteproc: qcom: Fix missing of_node_put in adsp_alloc_memory_region remoteproc: move rproc_da_to_va declaration to remoteproc.h remoteproc: wkup_m3: Set sysfs_read_only flag remoteproc: Introduce sysfs_read_only flag remoteproc: Fix count check in rproc_coredump_write() remoteproc: mtk_scp: Use dev_err_probe() where possible ...
| * remoteproc: qcom_q6v5_mss: Create platform device for BAM-DMUXStephan Gerhold2022-03-111-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The modem remoteproc on older Qualcomm SoCs (e.g. MSM8916 and MSM8974) implements the BAM-DMUX protocol to allow access to the network data channels of the modem. The hardware/firmware resources required to implement the BAM-DMUX driver are described in an extra node in the device tree (with the compatible "qcom,bam-dmux"). This node logically belongs below the modem remoteproc, so that both control interfaces (rpmsg_wwan_ctrl) and network interfaces (bam_dmux) have a common parent. Unlike other child devices of the modem remoteproc, the bam-dmux device currently does not follow the state of the remoteproc (i.e. it is not added/removed when the remoteproc is started/stopped). However, this is an implementation detail of the bam_dmux driver in Linux that might change in the future. To be flexible for future changes, create a standard platform device specifically only for "qcom,bam-dmux", rather than populating all child nodes. This is also more consistent with the way the other child nodes are handled in the driver. Note: of_platform_device_create() and of_node_put() have NULL-checks internally, so there is no need to check if the "qcom,bam-dmux" node actually exists in the device tree. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220228225400.146555-2-stephan@gerhold.net
| * remoteproc: qcom_q6v5_mss: Fix some leaks in q6v5_alloc_memory_regionMiaoqian Lin2022-03-111-4/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The device_node pointer is returned by of_parse_phandle() or of_get_child_by_name() with refcount incremented. We should use of_node_put() on it when done. This function only call of_node_put(node) when of_address_to_resource succeeds, missing error cases. Fixes: 278d744c46fd ("remoteproc: qcom: Fix potential device node leaks") Fixes: 051fb70fd4ea ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220308064522.13804-1-linmq006@gmail.com
* | soc: qcom: mdt_loader: Allow hash segment to be split outBjorn Andersson2022-02-031-3/+4
|/ | | | | | | | | | | | | | | It's been observed that some firmware found in a Qualcomm SM8450 device has the hash table in a separate .bNN file. Use the newly extracted helper function to load this segment from the separate file, if it's determined that the hashes are not part of the already loaded firmware. In order to do this, the function needs access to the firmware basename and to provide more useful error messages a struct device to associate the errors with. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20220128025513.97188-4-bjorn.andersson@linaro.org
* remoteproc: qcom_q6v5_mss: Use devm_platform_ioremap_resource_byname() to ↵zhaoxiao2021-10-151-5/+2
| | | | | | | | | | | simplify code In this function, devm_platform_ioremap_resource_byname() should be suitable to simplify code. Signed-off-by: zhaoxiao <long870912@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210906071147.9095-1-long870912@gmail.com
* remoteproc: mss: q6v5-mss: Add modem support on SC7280Sibi Sankar2021-09-271-4/+249
| | | | | | | | | | | | Add out of reset sequence support for modem sub-system on SC7280 SoCs. It requires access to an additional set of qaccept registers, external power/clk control registers and halt vq6 register to put the modem back into reset. Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/1631886935-14691-6-git-send-email-sibis@codeaurora.org
* remoteproc: qcom: q6v5: Use qmp_send to update co-processor load stateSibi Sankar2021-09-271-36/+8
| | | | | | | | | | | | | | | | | | | | The power domains exposed by the AOSS QMP driver control the load state resources linked to modem, adsp, cdsp remoteprocs. These are used to notify the Always on Subsystem (AOSS) that a particular co-processor is up/down. AOSS uses this information to wait for the co-processors to suspend before starting its sleep sequence. These co-processors enter low-power modes independent to that of the application processor and the load state resources linked to them are expected to remain unaltered across system suspend/resume cycles. To achieve this behavior lets stop using the power-domains exposed by the AOSS QMP node and replace them with generic qmp_send interface instead. Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> [bjorn: Fixed up build error in q6v5_wcss_remove()] Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/1631800770-371-5-git-send-email-sibis@codeaurora.org
* remoteproc: qcom_q6v5_mss: Validate p_filesz in ELF loaderBjorn Andersson2021-03-181-0/+18
| | | | | | | | | | | | Analog to the issue in the common mdt_loader code the MSS ELF loader does not validate that p_filesz bytes will fit in the memory region and that the loaded segments are not truncated. Fix this in the same way as proposed for the mdt_loader. Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Fixes: 135b9e8d1cd8 ("remoteproc: qcom_q6v5_mss: Validate modem blob firmware size before load") Link: https://lore.kernel.org/r/20210312232002.3466791-1-bjorn.andersson@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
* remoteproc: qcom_q6v5_mss: Provide errors for firmware-name parsingBjorn Andersson2021-03-181-2/+6
| | | | | | | | | Failing to read the "firmware-name" DT property without informing the developer is annoying, add some helpful debug prints. Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Link: https://lore.kernel.org/r/20210312002605.3273255-1-bjorn.andersson@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
* remoteproc: q6v5-mss: fix error handling in q6v5_pds_enableZhang Qilong2020-12-101-1/+4
| | | | | | | | | | | | | | | | | | | If the pm_runtime_get_sync failed in q6v5_pds_enable when loop (i), The unroll_pd_votes will start from (i - 1), and it will resulted in following problems: 1) pm_runtime_get_sync will increment pm usage counter even it failed. Forgetting to pm_runtime_put_noidle will result in reference leak. 2) Have not reset pds[i] performance state. Then we fix it. Fixes: 4760a896be88e ("remoteproc: q6v5-mss: Vote for rpmh power domains") Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Link: https://lore.kernel.org/r/20201102143433.143996-1-zhangqilong3@huawei.com Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
* remoteproc: qcom: q6v5: Query sysmon before graceful shutdownBjorn Andersson2020-11-251-1/+1
| | | | | | | | | | | | | Requesting a graceful shutdown through the shared memory state signals will not be acked in the event that sysmon has already successfully shut down the remote firmware. So extend the stop request API to optionally take the remoteproc's sysmon instance and query if there's already been a successful shutdown attempt, before doing the signal dance. Tested-by: Steev Klimaszewski <steev@kali.org> Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org> Link: https://lore.kernel.org/r/20201122054135.802935-4-bjorn.andersson@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
* remoteproc: qcom_q6v5_mss: map/unmap MBA region before/after useSibi Sankar2020-11-241-15/+22
| | | | | | | | | | | The application processor accessing the MBA region after assigning it to the remote Q6 would lead to an XPU violation. Fix this by un-mapping the MBA region post firmware copy and MBA text log dumps. Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/1604473422-29639-2-git-send-email-sibis@codeaurora.org [bjorn: Renamed "ptr" to "mba_region"] Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
* remoteproc: qcom_q6v5_mss: Replace ioremap with memremapSibi Sankar2020-11-241-6/+6
| | | | | | | | | | | Fix the sparse warnings reported by the kernel test bot by replacing ioremap calls with memremap. Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/1604473422-29639-1-git-send-email-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
* remoteproc: qcom_q6v5_mss: Allow replacing regulators with power domainsStephan Gerhold2020-10-261-12/+56
| | | | | | | | | | | | | | | | | | | | | | Newer platforms vote for necessary power domains through the power domain subsystem. For historical reasons older platforms like MSM8916 or MSM8974 still control these as regulators. Managing them as power domains is preferred since that allows us to vote for corners instead of raw voltages. Make it possible for MSM8916 and MSM8974 to manage these as power domains. For compatibility with old device trees we still need to support falling back to the regulators when necessary. The way this is implemented here is that the deprecated regulators are defined as "fallback_proxy_supply". Only if attaching the power domains fails because they are not specified (-ENODATA) we request and manage the fallback regulators instead. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Link: https://lore.kernel.org/r/20200916104135.25085-7-stephan@gerhold.net Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
* remoteproc: qcom_q6v5: Assign mpss region to Q6 before MBA bootSibi Sankar2020-09-251-3/+13
| | | | | | | | | | | On secure devices which support warm reset, the MBA firmware requires access to the modem region to clear them out. Hence provide Q6 access to this region before MBA boot. This will be a nop during a modem SSR. Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200917175840.18708-1-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
* Merge tag 'rproc-v5.9' of ↵Linus Torvalds2020-08-111-67/+90
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc Pull remoteproc updates from Bjorn Andersson: "This introduces a new "detached" state for remote processors that are deemed to be running at the time Linux boots and the infrastructure for "attaching" to these. It then introduces the support for performing this operation for the STM32 platform. The coredump functionality is moved out from the core file and gains support for an optional mode where the recovery phase awaits the notification from devcoredump that the dump should be released. This allows userspace to grab the coredump in scenarios where vmalloc space is too low for creating a complete copy of the coredump before handing this to devcoredump. A new character device based interface is introduced to allow tying the stoppage of a remote processor to the termination of a user space process. This is useful in situations when such process provides crucial resources/operations for the firmware running on the remote processor. The Texas Instrument K3 driver gains support for the C66x and C71x DSPs. Qualcomm remoteprocs gains support for stashing relocation information in IMEM, to aid post mortem debugging and the crash notification mechanism is generalized to be reusable in cases where loosely coupled drivers needs to know about the status of a remote processor. One such example is the IPA hardware block, which is jointly owned with the modem and migrated to this improved interface. It also introduces a number of bug fixes and debug improvements for the Qualcomm modem remoteproc driver. And it cleans up the inconsistent interface for remoteproc drivers to implement power management" * tag 'rproc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (56 commits) remoteproc: core: Register the character device interface remoteproc: Add remoteproc character device interface remoteproc: kill IPA notify code net: ipa: new notification infrastructure remoteproc: k3-dsp: Add support for C71x DSPs dt-bindings: remoteproc: k3-dsp: Update bindings for C71x DSPs remoteproc: k3-dsp: Add support for L2RAM loading on C66x DSPs remoteproc: k3-dsp: Add a remoteproc driver of K3 C66x DSPs dt-bindings: remoteproc: Add bindings for C66x DSPs on TI K3 SoCs remoteproc: k3: Add TI-SCI processor control helper functions remoteproc: Introduce rproc_of_parse_firmware() helper dt-bindings: arm: keystone: Add common TI SCI bindings remoteproc: qcom_q6v5_mss: Remove redundant running state remoteproc: qcom: q6v5: Update running state before requesting stop remoteproc: qcom_q6v5_mss: Add modem debug policy support remoteproc: qcom_q6v5_mss: Validate modem blob firmware size before load remoteproc: qcom_q6v5_mss: Validate MBA firmware size before load rpmsg: update documentation remoteproc: qcom_q6v5_mss: Add MBA log extraction support remoteproc: Add coredump debugfs entry ...
| * remoteproc: kill IPA notify codeAlex Elder2020-07-281-38/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The IPA code now uses the generic remoteproc SSR notification mechanism. This makes the original IPA notification code unused and unnecessary, so get rid of it. This is effectively a revert of commit d7f5f3c89c1a ("remoteproc: add IPA notification to q6v5 driver"). Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Alex Elder <elder@linaro.org> Link: https://lore.kernel.org/r/20200724181142.13581-3-elder@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: qcom_q6v5_mss: Remove redundant running stateSibi Sankar2020-07-271-5/+0
| | | | | | | | | | | | | | | | | | | | | | Remove the redundant running state, as an equivalent is maintained in the common q6v5 resource handling helpers. Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Evan Green <evgreen@chromium.org> Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200602163257.26978-2-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: qcom_q6v5_mss: Add modem debug policy supportSibi Sankar2020-07-271-1/+24
| | | | | | | | | | | | | | | | | | | | Add modem debug policy support which will enable coredumps and live debug support when the msadp firmware is present on secure devices. Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200722201047.12975-4-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: qcom_q6v5_mss: Validate modem blob firmware size before loadSibi Sankar2020-07-271-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following mem abort is observed when one of the modem blob firmware size exceeds the allocated mpss region. Fix this by restricting the copy size to segment size using request_firmware_into_buf before load. Err Logs: Unable to handle kernel paging request at virtual address Mem abort info: ... Call trace: __memcpy+0x110/0x180 rproc_start+0xd0/0x190 rproc_boot+0x404/0x550 state_store+0x54/0xf8 dev_attr_store+0x44/0x60 sysfs_kf_write+0x58/0x80 kernfs_fop_write+0x140/0x230 vfs_write+0xc4/0x208 ksys_write+0x74/0xf8 ... Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Fixes: 051fb70fd4ea4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5") Cc: stable@vger.kernel.org Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200722201047.12975-3-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: qcom_q6v5_mss: Validate MBA firmware size before loadSibi Sankar2020-07-271-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following mem abort is observed when the mba firmware size exceeds the allocated mba region. MBA firmware size is restricted to a maximum size of 1M and remaining memory region is used by modem debug policy firmware when available. Hence verify whether the MBA firmware size lies within the allocated memory region and is not greater than 1M before loading. Err Logs: Unable to handle kernel paging request at virtual address Mem abort info: ... Call trace: __memcpy+0x110/0x180 rproc_start+0x40/0x218 rproc_boot+0x5b4/0x608 state_store+0x54/0xf8 dev_attr_store+0x44/0x60 sysfs_kf_write+0x58/0x80 kernfs_fop_write+0x140/0x230 vfs_write+0xc4/0x208 ksys_write+0x74/0xf8 __arm64_sys_write+0x24/0x30 ... Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Fixes: 051fb70fd4ea4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5") Cc: stable@vger.kernel.org Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200722201047.12975-2-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: qcom_q6v5_mss: Add MBA log extraction supportSibi Sankar2020-07-211-1/+37
| | | | | | | | | | | | | | | | | | | | | | On SC7180 the MBA firmware stores the bootup text logs in a 4K segment at the beginning of the MBA region. Add support to extract the logs which will be useful to debug mba boot/authentication issues. Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200721112935.25716-3-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: Pass size and offset as arguments to segment dump functionRishabh Bhatnagar2020-07-211-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change the segment dump API signature to include size and offset arguments. Refactor the qcom_q6v5_mss driver to use these arguments while copying the segment. Doing this lays the ground work for "inline" coredump functionality being added in the next patch. Tested-by: Sibi Sankar <sibis@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Sibi Sankar <sibis@codeaurora.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org> Link: https://lore.kernel.org/r/1594938035-7327-4-git-send-email-rishabhb@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: qcom_q6v5_mss: Replace mask based tracking with sizeSibi Sankar2020-07-211-9/+8
| | | | | | | | | | | | | | | | | | | | | | | | In order to land inline coredump support for mss, the dump_segment function would need to support granularities less than the segment size. This is achieved by replacing mask based tracking with size. Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org> Link: https://lore.kernel.org/r/1594938035-7327-3-git-send-email-rishabhb@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: qcom_q6v5_mss: Monitor MSS_STATUS for boot completionSibi Sankar2020-07-161-6/+6
| | | | | | | | | | | | | | | | | | | | | | On secure devices there exists a race condition which could lock the MSS CONFIG AHB bus thus preventing access to BOOT_STATUS register during SSR. Switch to polling the MSS_STATUS register with an additional 10 us delay to reliably track boot completion. Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200716120514.21588-1-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: qcom: Update PIL relocation info on loadBjorn Andersson2020-07-011-0/+3
| | | | | | | | | | | | | | | | | | | | | | Update the PIL relocation information in IMEM with information about where the firmware for various remoteprocs are loaded. Reviewed-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20200622191942.255460-4-bjorn.andersson@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
* | iov_iter: Move unnecessary inclusion of crypto/hash.hHerbert Xu2020-06-301-0/+1
|/ | | | | | | | | | | | | | | | | | | | | | | The header file linux/uio.h includes crypto/hash.h which pulls in most of the Crypto API. Since linux/uio.h is used throughout the kernel this means that every tiny bit of change to the Crypto API causes the entire kernel to get rebuilt. This patch fixes this by moving it into lib/iov_iter.c instead where it is actually used. This patch also fixes the ifdef to use CRYPTO_HASH instead of just CRYPTO which does not guarantee the existence of ahash. Unfortunately a number of drivers were relying on linux/uio.h to provide access to linux/slab.h. This patch adds inclusions of linux/slab.h as detected by build failures. Also skbuff.h was relying on this to provide a declaration for ahash_request. This patch adds a forward declaration instead. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* Merge tag 'rproc-v5.8' of ↵Linus Torvalds2020-06-081-113/+60
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc Pull remoteproc updates from Bjorn Andersson: "This introduces device managed versions of functions used to register remoteproc devices, add support for remoteproc driver specific resource control, enables remoteproc drivers to specify ELF class and machine for coredumps. It integrates pm_runtime in the core for keeping resources active while the remote is booted and holds a wake source while recoverying a remote processor after a firmware crash. It refactors the remoteproc device's allocation path to simplify the logic, fix a few cleanup bugs and to not clone const strings onto the heap. Debugfs code is simplifies using the DEFINE_SHOW_ATTRIBUTE and a zero-length array is replaced with flexible-array. A new remoteproc driver for the JZ47xx VPU is introduced, the Qualcomm SM8250 gains support for audio, compute and sensor remoteprocs and the Qualcomm SC7180 modem support is cleaned up and improved. The Qualcomm glink subsystem-restart driver is merged into the main glink driver, the Qualcomm sysmon driver is extended to properly notify remote processors about all other remote processors' state transitions" * tag 'rproc-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (43 commits) remoteproc: Fix an error code in devm_rproc_alloc() MAINTAINERS: Add myself as reviewer for Ingenic rproc driver remoteproc: ingenic: Added remoteproc driver remoteproc: Add support for runtime PM dt-bindings: Document JZ47xx VPU auxiliary processor remoteproc: wcss: Fix arguments passed to qcom_add_glink_subdev() remoteproc: Fix and restore the parenting hierarchy for vdev remoteproc: Fall back to using parent memory pool if no dedicated available remoteproc: Replace zero-length array with flexible-array remoteproc: wcss: add support for rpmsg communication remoteproc: core: Prevent system suspend during remoteproc recovery remoteproc: qcom_q6v5_mss: Remove unused q6v5_da_to_va function remoteproc: qcom_q6v5_mss: map/unmap mpss segments before/after use remoteproc: qcom_q6v5_mss: Drop accesses to MPSS PERPH register space dt-bindings: remoteproc: qcom: Replace halt-nav with spare-regs remoteproc: qcom: pas: Add SM8250 PAS remoteprocs dt-bindings: remoteproc: qcom: pas: Add SM8250 remoteprocs remoteproc: qcom_q6v5_mss: Extract mba/mpss from memory-region dt-bindings: remoteproc: qcom: Use memory-region to reference memory remoteproc: qcom: pas: Add SC7180 Modem support ...
| * remoteproc: qcom_q6v5_mss: Remove unused q6v5_da_to_va functionSibi Sankar2020-05-121-14/+0
| | | | | | | | | | | | | | | | | | | | Remove unsed q6v5_da_to_va function as the mss driver uses a per segment dump function. Tested-by: Evan Green <evgreen@chromium.org> Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200415071619.6052-2-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: qcom_q6v5_mss: map/unmap mpss segments before/after useSibi Sankar2020-05-121-11/+20
| | | | | | | | | | | | | | | | | | | | | | The application processor accessing the mpss region when the Q6 modem is running will lead to an XPU violation. Fix this by un-mapping the mpss segments post copy during mpss authentication and coredumps. Tested-by: Evan Green <evgreen@chromium.org> Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200415071619.6052-1-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: qcom_q6v5_mss: Drop accesses to MPSS PERPH register spaceSibi Sankar2020-05-121-84/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 7C retail devices using MSA based boot will result in a fuse combination which will prevent accesses to MSS PERPH register space where the mpss clocks and halt-nav reside. So drop all accesses to the MPSS PERPH register space. Issuing HALT NAV request and turning on the mss clocks as part of SSR will no longer be required since the modem firmware will have the necessary fixes to ensure that there are no pending NAV DMA transactions. Tested-by: Evan Green <evgreen@chromium.org> Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200415145110.20624-3-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: qcom_q6v5_mss: Extract mba/mpss from memory-regionSibi Sankar2020-05-111-3/+18
| | | | | | | | | | | | | | | | | | | | In the absence of mba and mpss sub-child extract the mba/mpss regions from the memory-region property. Tested-by: Evan Green <evgreen@chromium.org> Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200421143228.8981-5-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
| * remoteproc: qcom: Pass ssr_name to glink subdeviceBjorn Andersson2020-05-071-1/+1
| | | | | | | | | | | | | | | | | | | | | | Pass ssr_name to glink subdevice in preparation for tying glink_ssr to the glink subdevice, rather than having its own "ssr subdevice". Acked-by: Chris Lew <clew@codeaurora.org> Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org> Acked-by: Rishabh Bhatnagar <rishabhb@codeaurora.org> Link: https://lore.kernel.org/r/20200423003736.2027371-2-bjorn.andersson@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-01 19:48:13 +0000