| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored and
this typically results in resource leaks. To improve here there is a quest
to make the remove callback return void. In the first step of this quest
all drivers are converted to .remove_new() which already returns void.
hisi_sas_remove() returned zero unconditionally so this was changed to
return void. Then it has the right prototype to be used directly as remove
callback for the two hisi_sas drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230518202043.261739-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch fixes the following warning:
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:2168:43: sparse: sparse: restricted __le32 degrades to integer
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304161254.NztCVZIO-lkp@intel.com/
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1684118481-95908-4-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
DMA setup lock timeout protection is added when DMA setup frames are
received. It's a function outside the protocol and used to prevent SATA
disk I/Os from being delivered for a long time. The default value is 100ms,
it's too strict and easily triggered timeout when the disk is overloaded or
faulty. Based on the average I/O latency of 300 disks, we adjust the value
to 2.5s.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1684118481-95908-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
For SAS HBAs of 920 and previous version, we use init_reg_v3_hw() to set
some registers which are related to HW boards. For SAS HBAs of 920B and
later version, those HW registers are set through firmware. And different
HBA models are distinguished through pci_dev->revision.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1684118481-95908-2-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The suspend/resume functions in this driver seem to have multiple problems,
the latest one just got introduced by a bugfix:
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c: In function '_suspend_v3_hw':
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:5142:39: error: 'struct dev_pm_info' has no member named 'usage_count'
5142 | if (atomic_read(&device->power.usage_count)) {
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c: In function '_suspend_v3_hw':
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:5142:39: error: 'struct dev_pm_info' has no member named 'usage_count'
5142 | if (atomic_read(&device->power.usage_count)) {
As far as I can tell, the 'usage_count' is not meant to be accessed by
device drivers at all, though I don't know what the driver is supposed to
do instead.
Another problem is the use of the deprecated UNIVERSAL_DEV_PM_OPS(), and
marking functions as __maybe_unused to avoid warnings about unused
functions. This should probably be changed to using
DEFINE_RUNTIME_DEV_PM_OPS().
Both changes require actually understanding what the driver needs to do,
and being able to test this, so instead here is the simplest patch to make
it pass the randconfig builds instead.
Fixes: e368d38cb952 ("scsi: hisi_sas: Exit suspend state when usage count is greater than 0")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230405083611.3376739-1-arnd@kernel.org
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
chenxiang <chenxiang66@hisilicon.com> says:
This series contain some fixes including:
- Grab sas_dev lock when traversing sas_dev list to avoid NULL
pointer
- Handle NCQ error when IPTT is valid
- Ensure all enabled PHYs up during controller reset
- Exit suspend state when usage count of runtime PM is greater than 0
https://lore.kernel.org/r/1679283265-115066-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When the current status of the host controller is suspended, enabling a
local PHY just after disabling all local PHYs in expander environment, a
hang as follows occurs:
[ 486.854655] INFO: task kworker/u256:1:899 blocked for more than 120 seconds.
[ 486.862207] Not tainted 6.1.0-rc4+ #1
[ 486.870545] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 486.878893] task:kworker/u256:1 state:D stack:0 pid:899 ppid:2 flags:0x00000008
[ 486.887745] Workqueue: 0000:74:02.0_disco_q sas_discover_domain [libsas]
[ 486.894704] Call trace:
[ 486.897400] __switch_to+0xf0/0x170
[ 486.901146] __schedule+0x3e4/0x1160
[ 486.904970] schedule+0x64/0x104
[ 486.908442] rpm_resume+0x158/0x6a0
[ 486.912163] __pm_runtime_resume+0x5c/0x84
[ 486.916489] smp_execute_task_sg+0x1f8/0x264 [libsas]
[ 486.921773] sas_discover_expander.part.0+0xbc/0x720 [libsas]
[ 486.927750] sas_discover_root_expander+0x90/0x154 [libsas]
[ 486.933552] sas_discover_domain+0x444/0x6d0 [libsas]
[ 486.938826] process_one_work+0x1e0/0x450
[ 486.943057] worker_thread+0x150/0x44c
[ 486.947015] kthread+0x114/0x120
[ 486.950447] ret_from_fork+0x10/0x20
[ 486.954292] INFO: task kworker/u256:2:1780 blocked for more than 120 seconds.
[ 486.961637] Not tainted 6.1.0-rc4+ #1
[ 486.966087] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 486.974356] task:kworker/u256:2 state:D stack:0 pid:1780 ppid:2 flags:0x00000208
[ 486.983141] Workqueue: 0000:74:02.0_event_q sas_port_event_worker [libsas]
[ 486.990252] Call trace:
[ 486.992930] __switch_to+0xf0/0x170
[ 486.996645] __schedule+0x3e4/0x1160
[ 487.000439] schedule+0x64/0x104
[ 487.003886] schedule_timeout+0x17c/0x1c0
[ 487.008102] wait_for_completion+0x7c/0x160
[ 487.012488] __flush_workqueue+0x104/0x3e0
[ 487.016782] sas_porte_bytes_dmaed+0x414/0x454 [libsas]
[ 487.022203] sas_port_event_worker+0x38/0x60 [libsas]
[ 487.027449] process_one_work+0x1e0/0x450
[ 487.031645] worker_thread+0x150/0x44c
[ 487.035594] kthread+0x114/0x120
[ 487.039017] ret_from_fork+0x10/0x20
[ 487.042828] INFO: task bash:11488 blocked for more than 121 seconds.
[ 487.049366] Not tainted 6.1.0-rc4+ #1
[ 487.053746] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 487.061953] task:bash state:D stack:0 pid:11488 ppid:10977 flags:0x00000204
[ 487.070698] Call trace:
[ 487.073355] __switch_to+0xf0/0x170
[ 487.077050] __schedule+0x3e4/0x1160
[ 487.080833] schedule+0x64/0x104
[ 487.084270] schedule_timeout+0x17c/0x1c0
[ 487.088474] wait_for_completion+0x7c/0x160
[ 487.092851] __flush_workqueue+0x104/0x3e0
[ 487.097137] drain_workqueue+0xb8/0x160
[ 487.101159] __sas_drain_work+0x50/0x90 [libsas]
[ 487.105963] sas_suspend_ha+0x64/0xd4 [libsas]
[ 487.110590] suspend_v3_hw+0x198/0x1e8 [hisi_sas_v3_hw]
[ 487.115989] pci_pm_runtime_suspend+0x5c/0x1d0
[ 487.120606] __rpm_callback+0x50/0x150
[ 487.124535] rpm_callback+0x74/0x80
[ 487.128204] rpm_suspend+0x110/0x640
[ 487.131955] rpm_idle+0x1f4/0x2d0
[ 487.135447] __pm_runtime_idle+0x58/0x94
[ 487.139538] queue_phy_enable+0xcc/0xf0 [libsas]
[ 487.144330] store_sas_phy_enable+0x74/0x100
[ 487.148770] dev_attr_store+0x20/0x34
[ 487.152606] sysfs_kf_write+0x4c/0x5c
[ 487.156437] kernfs_fop_write_iter+0x120/0x1b0
[ 487.161049] vfs_write+0x2d0/0x36c
[ 487.164625] ksys_write+0x70/0x100
[ 487.168194] __arm64_sys_write+0x24/0x30
[ 487.172280] invoke_syscall+0x50/0x120
[ 487.176186] el0_svc_common.constprop.0+0x168/0x190
[ 487.181214] do_el0_svc+0x34/0xc0
[ 487.184680] el0_svc+0x2c/0xb4
[ 487.187879] el0t_64_sync_handler+0xb8/0xbc
[ 487.192205] el0t_64_sync+0x19c/0x1a0
We find that when all local PHYs are disabled, all the devices will be
removed, the ->runtime_suspend() callback suspend_v3_hw() directly execute
since the controller usage count drop to 0. On the other side, the first
local PHY is enabled through the sysfs interface, and ensures that function
phy_up_v3_hw() is completed due to suspend_v3_hw()->
interrupt_disable_v3_hw(). In the expander scenario,
sas_discover_root_expander() is executed in event work
DISCE_DISCOVER_DOMAIN, which will increases the controller usage count and
carry out a resume and sends SMPIO, it cannot be completed because the
runtime PM status of the controller is RPM_SUSPENDING. At the same time,
the ->runtime_suspend() callback suspend_v3_hw() also cannot complete the
process because of drain libsas event queue in sas_suspend_ha(), so hung
occurs.
(thread 1) | (thread 2)
... |
rpm_idle() |
... |
__update_runtime_status(RPM_SUSPENDING)|
... | ...
suspend_v3_hw() | smp_execute_task_sg()
... | ...
interrupt_disable_v3_hw() | pm_runtime_get_sync()
| ...
... | rpm_resume() //RPM_SUSPENDING
|
__sas_drain_work() |
To fix this, check if the current runtime PM status of the controller
allows to be suspended continue after interrupt_disable_v3_hw(), return
immediately if not.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hislicon.com>
Link: https://lore.kernel.org/r/1679283265-115066-5-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
For the controller reset operation, hisi_sas_phy_enable() is executed for
each enabled local PHY, and refresh the port id of each device based on the
latest hisi_sas_phy->port_id after 1 second sleep, hisi_sas_phy->port_id is
configured in the interrupt processing function phy_up_v3_hw(). However, in
directly attached scenario, for some SATA disks the amount of time for
phyup more than 1s sometimes. In this case, incorrect port id may be
configured in hisi_sas_refresh_port_id(). As a result, all the internal
IOs fail and disk lost, such as follows:
[10717.666565] hisi_sas_v3_hw 0000:74:02.0: phyup: phy1 link_rate=10(sata)
[10718.826813] hisi_sas_v3_hw 0000:74:02.0: erroneous completion iptt=63
task=00000000c1ab1c2b dev id=200 addr=5000000000000501 CQ hdr: 0x8000007 0xc8003f 0x0
0x0 Error info: 0x0 0x0 0x0 0x0
[10718.843428] sas: TMF task open reject failed 5000000000000501
[10718.849242] hisi_sas_v3_hw 0000:74:02.0: erroneous completion iptt=64
task=00000000c1ab1c2b dev id=200 addr=5000000000000501 CQ hdr: 0x8000007 0xc80040 0x0
0x0 Error info: 0x0 0x0 0x0 0x0
[10718.865856] sas: TMF task open reject failed 5000000000000501
[10718.871670] hisi_sas_v3_hw 0000:74:02.0: erroneous completion iptt=65
task=00000000c1ab1c2b dev id=200 addr=5000000000000501 CQ hdr: 0x8000007 0xc80041 0x0
0x0 Error info: 0x0 0x0 0x0 0x0
[10718.888284] sas: TMF task open reject failed 5000000000000501
[10718.894093] sas: executing TMF for 5000000000000501 failed after 3 attempts!
[10718.901114] hisi_sas_v3_hw 0000:74:02.0: ata disk 5000000000000501 reset failed
[10718.908410] hisi_sas_v3_hw 0000:74:02.0: controller reset complete
.....
[10773.298633] ata216.00: revalidation failed (errno=-19)
[10773.303753] ata216.00: disable device
So the time of waitting for PHYs up is 1s which may be not enough. To solve
the issue, running hisi_sas_phy_enable() in parallel through async
operations and use wait_for_completion_timeout() to wait for PHYs come up
instead of directly sleep for 1 second.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1679283265-115066-4-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
If an NCQ error occurs when the IPTT is valid and slot->abort flag is set
in completion path, sas_task_abort() will be called to abort only one NCQ
command now, and the host would be set to SHOST_RECOVERY state. But this
may not kick-off EH Immediately until other outstanding QCs timeouts. As a
result, the host may remain in the SHOST_RECOVERY state for up to 30
seconds, such as follows:
[7972317.645234] hisi_sas_v3_hw 0000:74:04.0: erroneous completion iptt=3264 task=00000000466116b8 dev id=2 sas_addr=0x5000000000000502 CQ hdr: 0x1883 0x20cc0 0x40000 0x20420000 Error info: 0x0 0x0 0x200000 0x0
[7972341.508264] sas: Enter sas_scsi_recover_host busy: 32 failed: 32
[7972341.984731] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 32 tries: 1
All NCQ commands that are in the queue should be aborted when an NCQ error
occurs in this scenario.
Fixes: 05d91b557af9 ("scsi: hisi_sas: Directly trigger SCSI error handling for completion errors")
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1679283265-115066-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When freeing slots in function slot_complete_v3_hw(), it is possible that
sas_dev.list is being traversed elsewhere, and it may trigger a NULL
pointer exception, such as follows:
==>cq thread ==>scsi_eh_6
==>scsi_error_handler()
==>sas_eh_handle_sas_errors()
==>sas_scsi_find_task()
==>lldd_abort_task()
==>slot_complete_v3_hw() ==>hisi_sas_abort_task()
==>hisi_sas_slot_task_free() ==>dereg_device_v3_hw()
==>list_del_init() ==>list_for_each_entry_safe()
[ 7165.434918] sas: Enter sas_scsi_recover_host busy: 32 failed: 32
[ 7165.434926] sas: trying to find task 0x00000000769b5ba5
[ 7165.434927] sas: sas_scsi_find_task: aborting task 0x00000000769b5ba5
[ 7165.434940] hisi_sas_v3_hw 0000:b4:02.0: slot complete: task(00000000769b5ba5) aborted
[ 7165.434964] hisi_sas_v3_hw 0000:b4:02.0: slot complete: task(00000000c9f7aa07) ignored
[ 7165.434965] hisi_sas_v3_hw 0000:b4:02.0: slot complete: task(00000000e2a1cf01) ignored
[ 7165.434968] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[ 7165.434972] hisi_sas_v3_hw 0000:b4:02.0: slot complete: task(0000000022d52d93) ignored
[ 7165.434975] hisi_sas_v3_hw 0000:b4:02.0: slot complete: task(0000000066a7516c) ignored
[ 7165.434976] Mem abort info:
[ 7165.434982] ESR = 0x96000004
[ 7165.434991] Exception class = DABT (current EL), IL = 32 bits
[ 7165.434992] SET = 0, FnV = 0
[ 7165.434993] EA = 0, S1PTW = 0
[ 7165.434994] Data abort info:
[ 7165.434994] ISV = 0, ISS = 0x00000004
[ 7165.434995] CM = 0, WnR = 0
[ 7165.434997] user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000f29543f2
[ 7165.434998] [0000000000000000] pgd=0000000000000000
[ 7165.435003] Internal error: Oops: 96000004 [#1] SMP
[ 7165.439863] Process scsi_eh_6 (pid: 4109, stack limit = 0x00000000c43818d5)
[ 7165.468862] pstate: 00c00009 (nzcv daif +PAN +UAO)
[ 7165.473637] pc : dereg_device_v3_hw+0x68/0xa8 [hisi_sas_v3_hw]
[ 7165.479443] lr : dereg_device_v3_hw+0x2c/0xa8 [hisi_sas_v3_hw]
[ 7165.485247] sp : ffff00001d623bc0
[ 7165.488546] x29: ffff00001d623bc0 x28: ffffa027d03b9508
[ 7165.493835] x27: ffff80278ed50af0 x26: ffffa027dd31e0a8
[ 7165.499123] x25: ffffa027d9b27f88 x24: ffffa027d9b209f8
[ 7165.504411] x23: ffffa027c45b0d60 x22: ffff80278ec07c00
[ 7165.509700] x21: 0000000000000008 x20: ffffa027d9b209f8
[ 7165.514988] x19: ffffa027d9b27f88 x18: ffffffffffffffff
[ 7165.520276] x17: 0000000000000000 x16: 0000000000000000
[ 7165.525564] x15: ffff0000091d9708 x14: ffff0000093b7dc8
[ 7165.530852] x13: ffff0000093b7a23 x12: 6e7265746e692067
[ 7165.536140] x11: 0000000000000000 x10: 0000000000000bb0
[ 7165.541429] x9 : ffff00001d6238f0 x8 : ffffa027d877af00
[ 7165.546718] x7 : ffffa027d6329600 x6 : ffff7e809f58ca00
[ 7165.552006] x5 : 0000000000001f8a x4 : 000000000000088e
[ 7165.557295] x3 : ffffa027d9b27fa8 x2 : 0000000000000000
[ 7165.562583] x1 : 0000000000000000 x0 : 000000003000188e
[ 7165.567872] Call trace:
[ 7165.570309] dereg_device_v3_hw+0x68/0xa8 [hisi_sas_v3_hw]
[ 7165.575775] hisi_sas_abort_task+0x248/0x358 [hisi_sas_main]
[ 7165.581415] sas_eh_handle_sas_errors+0x258/0x8e0 [libsas]
[ 7165.586876] sas_scsi_recover_host+0x134/0x458 [libsas]
[ 7165.592082] scsi_error_handler+0xb4/0x488
[ 7165.596163] kthread+0x134/0x138
[ 7165.599380] ret_from_fork+0x10/0x18
[ 7165.602940] Code: d5033e9f b9000040 aa0103e2 eb03003f (f9400021)
[ 7165.609004] kernel fault(0x1) notification starting on CPU 75
[ 7165.700728] ---[ end trace fc042cbbea224efc ]---
[ 7165.705326] Kernel panic - not syncing: Fatal exception
To fix the issue, grab sas_dev lock when traversing the members of
sas_dev.list in dereg_device_v3_hw() and hisi_sas_release_tasks() to avoid
concurrency of adding and deleting member. When function
hisi_sas_release_tasks() calls hisi_sas_do_release_task() to free slot, the
lock cannot be grabbed again in hisi_sas_slot_task_free(), then a bool
parameter need_lock is added.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1679283265-115066-2-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | | |
Pull in the fixes branch to resolve an mpi3mr conflict reported by
sfr.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In case devm_add_action() fails, check it in the caller of
interrupt_preinit_v3_hw().
Link: https://lore.kernel.org/r/20230227031030.893324-1-void0red@gmail.com
Signed-off-by: Kang Chen <void0red@gmail.com>
Acked-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|\ \ \
| |_|/
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Bart Van Assche <bvanassche@acm.org> says:
It helps humans and the compiler if it is made explicit that SCSI host
templates are not modified. Hence this patch series that constifies most
SCSI host templates. Please consider this patch series for the next merge
window.
Link: https://lore.kernel.org/r/20230322195515.1267197-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |/
| |
| |
| |
| |
| |
| |
| |
| | |
Make it explicit that the SCSI host template is not modified.
Acked-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230322195515.1267197-42-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add device attribute experimental_iopoll_q_cnt to indicate how many iopoll
queues are used for v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1678169355-76215-5-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently we sync irq to avoid freeing task before using task in I/O
completion. After adding io_uring support, we need to do something similar
for poll queues. As the process of CQ entries on poll queue are protected
by spinlock cq->lock, we can use spin_lock() + spin_unlock() on cq->lock to
make sure that CQ entries are processed to completion and then the complete
queue is synced.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1678169355-76215-4-git-send-email-chenxiang66@hisilicon.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add a module parameter to set how many queues are used for iopoll. Also
fill the interface mq_poll. For internal I/Os from libsas and libata we use
non-iopoll queue (queue 0) to deliver and complete them. But for internal
abort I/Os, just don't send them for poll queues.
There is still a risk associated as this sends internal abort commands to
non-iopoll queues which actually requires sending an internal abort command
to every queue. As a result, make the module parameter as "experimental"
for now.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1678169355-76215-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|/
|
|
|
|
|
|
|
|
|
|
| |
Put the work of processing cq slots in a separate function,
complete_v3_hw(), which can then be used by cq_thread_v3_hw() and other
functions when adding poll support.
Co-developed-by: John Garry <john.garry@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1678169355-76215-2-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
when refreshing port id
Currently the driver sets the port invalid if one phy in the port is not
enabled, which may cause issues in expander situation. In directly attached
situation, if phy up doesn't occur in time when refreshing port id, the
port is incorrectly set to invalid which will also cause disk lost.
Therefore set a port invalid only if there are no devices attached to the
port.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1672805000-141102-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently clear task set is used to abort all commands remaining in the
disk when the SAS disk is discovered, and if the disk is discovered by two
initiators, other I_T nexuses are also affected. So use abort task set
instead and take effect only on the specified I_T nexus.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1672805000-141102-2-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The reserved tags were put in the lower region of the tagset in commit
f7d190a94e35 ("scsi: hisi_sas: Put reserved tags in lower region of
tagset"). However, only the allocate function was changed, freeing was not
handled. This resulted in a failure to boot:
[ 33.467345] hisi_sas_v3_hw 0000:b4:02.0: task exec: failed[-132]!
[ 33.473413] sas: Executing internal abort failed 5000000000000603 (-132)
[ 33.480088] hisi_sas_v3_hw 0000:b4:02.0: I_T nexus reset: internal abort (-132)
[ 33.657336] hisi_sas_v3_hw 0000:b4:02.0: task exec: failed[-132]!
[ 33.663403] ata7.00: failed to IDENTIFY (I/O error, err_mask=0x40)
[ 35.787344] hisi_sas_v3_hw 0000:b4:04.0: task exec: failed[-132]!
[ 35.793411] sas: Executing internal abort failed 5000000000000703 (-132)
[ 35.800084] hisi_sas_v3_hw 0000:b4:04.0: I_T nexus reset: internal abort (-132)
[ 35.977335] hisi_sas_v3_hw 0000:b4:04.0: task exec: failed[-132]!
[ 35.983403] ata10.00: failed to IDENTIFY (I/O error, err_mask=0x40)
[ 35.989643] ata10.00: revalidation failed (errno=-5)
Fixes: f7d190a94e35 ("scsi: hisi_sas: Put reserved tags in lower region of tagset")
Cc: John Garry <john.g.garry@oracle.com>
Cc: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Acked-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
SATA devices on an expander may be removed and not be found again when I_T
nexus reset and revalidation are processed simultaneously.
The issue comes from:
- Revalidation can remove SATA devices in link reset, e.g. in
hisi_sas_clear_nexus_ha().
- However, hisi_sas_debug_I_T_nexus_reset() polls the state of a SATA
device on an expander after sending link_reset, where it calls:
hisi_sas_debug_I_T_nexus_reset
sas_ata_wait_after_reset
ata_wait_after_reset
ata_wait_ready
smp_ata_check_ready
sas_ex_phy_discover
sas_ex_phy_discover_helper
sas_set_ex_phy
The ex_phy's change count is updated in sas_set_ex_phy(), so SATA
devices after a link reset may not be found later through revalidation.
A similar issue was reported in:
commit 0f3fce5cc77e ("[SCSI] libsas: fix ata_eh clobbering ex_phys via
smp_ata_check_ready")
commit 87c8331fcf72 ("[SCSI] libsas: prevent domain rediscovery competing
with ata error handling").
To address this issue, in hisi_sas_debug_I_T_nexus_reset(), we now call
smp_ata_check_ready_type() that only polls the device type while not
updating the ex_phy's data of libsas.
Fixes: 71453bd9d1bf ("scsi: hisi_sas: Use sas_ata_wait_after_reset() in IT nexus reset")
Signed-off-by: Jie Zhan <zhanjie9@hisilicon.com>
Link: https://lore.kernel.org/r/20221118083714.4034612-5-zhanjie9@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
HA reset"
This reverts commit f5f2a2716055ad8c0c4ff83e51d667646c6c5d8a.
This is now unnecessary to solve the SATA devices missing issue in
hisi_sas_clear_nexus_ha(). Hence, we should not ignore bcast events during
sas_eh_handle_sas_errors() in case of missing bcast events, unless a
justified need is found and a mechanism to defer (but not ignore) bcast
events in sas_eh_handle_sas_errors() is provided.
Also, in hisi_sas_clear_nexus_ha(), there is nothing further to handle in
"out: " other than return, so that part can be reverted.
Signed-off-by: Jie Zhan <zhanjie9@hisilicon.com>
Link: https://lore.kernel.org/r/20221118083714.4034612-3-zhanjie9@hisilicon.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This reverts commit 11ff0c98fca35df16c84d4eee52008faecaf10a6.
Draining or flushing events in hisi_sas_rescan_topology() can hang the
driver, typically with phy up or phy down events being processed,
i.e. sas_porte_bytes_dmaed() or sas_phye_loss_of_signal().
Signed-off-by: Jie Zhan <zhanjie9@hisilicon.com>
Link: https://lore.kernel.org/r/20221118083714.4034612-2-zhanjie9@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
| |
To be consistent with blk-mq, put the reserved tags in the lower region of
the tagset. Eventually we hope to get rid of all this reserved tag
management.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1666091763-11023-4-git-send-email-john.garry@huawei.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
| |
Use sas_task_find_rq() to lookup the request per task for its driver tag.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1666091763-11023-3-git-send-email-john.garry@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The attached phy finding is open coded. Replace it with
sas_find_attached_phy_id(). To keep things consistent, the return value of
hisi_sas_dev_found() is also changed to -ENODEV after calling
sas_find_attathed_phy_id() failed.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20220928070130.3657183-6-yanaijie@huawei.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When an NCQ error occurs, the controller will abnormally complete the I/Os
that are newly delivered to disk, and bit8 in CQ dw3 will be set which
indicates that the SATA disk is in error state. The current processing flow
is to set ts->stat to SAS_OPEN_REJECT and then sas_ata_task_done() will set
FIS stat to ATA_ERR. After analyzing the I/O by ata_eh_analyze_tf(),
err_mask will set to AC_ERR_HSM. If media error occurs for four times
within 10 minutes and the chip rejects new I/Os for four times, NCQ will be
disabled due to excessive errors, which is undesirable.
Therefore, use sas_task_abort() to handle abnormally completed I/Os when
SATA disk is in error state, as these abnormally completed I/Os are already
processed by sas_ata_device_link_abort() and qc->flag are set to
ATA_QCFLAG_FAILED. If sas_task_abort() is used, qc->err_mask will not be
modified in EH. Unlike the current process flow, it will not increase the
count of ECAT_TOUT_HSM and not turn off NCQ. Like other I/Os on the disk
that do not have an error but do not return after the NCQ error, they are
retried after the EH.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1665998435-199946-5-git-send-email-john.garry@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When CQ header dw3 SATA_DISK_ERR is set it means this SATA disk is in error
state and the current IPTT is invalid. An invalid IPTT does not correspond
to any slot.
In this scenario, new I/Os that delivered to disk will be rejected by the
controller and all I/Os remaining in the disk should be aborted, which we
add here with the sas_ata_device_link_abort() call.
In hisi_sas_abort_task() we don't want to issue a soft reset as it may
cause info to be lost in the target disk for the ATA EH autopsy. In this
case, just release resources - the disk won't return other I/Os normally
after NCQ Error, so this is safe.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1665998435-199946-4-git-send-email-john.garry@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
| |
Each branch currently defines a slot variable independently, and it is
neater to move it to the function head.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1665998435-199946-3-git-send-email-john.garry@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (qla2xxx, lpfc, ufs, hisi_sas, mpi3mr,
mpt3sas, target). The biggest change (from my biased viewpoint) being
that the mpi3mr now attached to the SAS transport class, making it the
first fusion type device to do so.
Beyond the usual bug fixing and security class reworks, there aren't a
huge number of core changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()
scsi: mpi3mr: Remove unnecessary cast
scsi: stex: Properly zero out the passthrough command structure
scsi: mpi3mr: Update driver version to 8.2.0.3.0
scsi: mpi3mr: Fix scheduling while atomic type bug
scsi: mpi3mr: Scan the devices during resume time
scsi: mpi3mr: Free enclosure objects during driver unload
scsi: mpi3mr: Handle 0xF003 Fault Code
scsi: mpi3mr: Graceful handling of surprise removal of PCIe HBA
scsi: mpi3mr: Schedule IRQ kthreads only on non-RT kernels
scsi: mpi3mr: Support new power management framework
scsi: mpi3mr: Update mpi3 header files
scsi: mpt3sas: Revert "scsi: mpt3sas: Fix ioc->base_readl() use"
scsi: mpt3sas: Revert "scsi: mpt3sas: Fix writel() use"
scsi: wd33c93: Remove dead code related to the long-gone config WD33C93_PIO
scsi: core: Add I/O timeout count for SCSI device
scsi: qedf: Populate sysfs attributes for vport
scsi: pm8001: Replace one-element array with flexible-array member
scsi: 3w-xxxx: Replace one-element array with flexible-array member
scsi: hptiop: Replace one-element array with flexible-array member in struct hpt_iop_request_ioctl_command()
...
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Remote devices may go missing from the per-device nexus reset part of the
HA nexus, i.e after the controller reset. This is because libsas may find
the devices to be gone as the phy may be temporarily down when processing
the bcast event generated from the nexus reset. Filter out bcast events
during this time to stop the devices being lost.
Link: https://lore.kernel.org/r/1662378529-101489-6-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Add a helper for bcast processing to reduce duplication.
Link: https://lore.kernel.org/r/1662378529-101489-5-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In resetting the controller, SATA devices may be lost.
The issue is that when we insert the bcast events to rescan the topology in
hisi_sas_rescan_topology(), when we subsequently nexus reset the SATA
devices in hisi_sas_async_I_T_nexus_reset(), there is a small timing window
in which the remote phy is down and we process the bcast event (meaning
that libsas judges that the disk is lost).
Ensure that all bcast events are processed prior to the nexus reset to
close this window.
Link: https://lore.kernel.org/r/1662378529-101489-4-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Once the controller HW has been reset then we can unset flag
HISI_SAS_HW_FAULT_BIT. In clearing this flag earlier we can now
successfully execute commands in hisi_sas_controller_reset_done(), like
bcast processing.
Link: https://lore.kernel.org/r/1662378529-101489-3-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Now that libsas and the SCSI core code limits the default sectors from
commit 4cbfca5f7750 ("scsi: scsi_transport_sas: cap shost opt_sectors
according to DMA optimal limit") and commit 608128d391fa ("scsi: sd: allow
max_sectors be capped at DMA optimal size limit"), there is no need for
the hack to limit the max HW sectors.
Link: https://lore.kernel.org/r/1662378529-101489-2-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since blk_mq_map_queues() and the .map_queues() callbacks always return 0,
change their return type into void. Most callers ignore the returned value
anyway.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Acked-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://lore.kernel.org/r/20220815170043.19489-3-bvanassche@acm.org
[axboe: fold in fix from Bart]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
|
|
|
|
|
|
|
|
|
|
| |
If the I/O completion response frame returned by the target device has been
written to the host memory and the err bit in the status field of the
received fis is 1, ts->stat should set to SAS_PROTO_RESPONSE, and this will
let EH analyze and further determine cause of failure.
Link: https://lore.kernel.org/r/1657823002-139010-5-git-send-email-john.garry@huawei.com
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
| |
Currently SMP tasks are DMA unmapped only when cq of SMP I/O is returned
normally. If the cq of SMP I/O is returned with exception actually SMP TAS
is never unmapped. Relocate DMA unmap of SMP task to fix the issue.
Link: https://lore.kernel.org/r/1657823002-139010-4-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
| |
Use slot->n_elem to store the return value of dma_map_sg() for SSP and SMP
IOs, and remove unnecessary variable n_elem_req.
Link: https://lore.kernel.org/r/1657823002-139010-3-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
| |
There is duplicated code between slave_configure_v3_hw() and
hisi_sas_slave_configure(), so call common function
hisi_sas_slave_configure() from slave_configure_v3_hw().
Link: https://lore.kernel.org/r/1657823002-139010-2-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|\
| |
| |
| |
| |
| | |
Bring in fixes to resolve a merge conflict in the lpfc driver update.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
If the controller is behind an IOMMU then the IOMMU IOVA caching range can
affect performance, as discussed in [0].
Limit the max HW sectors to not exceed this limit. We need to hardcode the
value until a proper DMA mapping API is available.
[0] https://lore.kernel.org/linux-iommu/20210129092120.1482-1-thunder.leizhen@huawei.com/
Link: https://lore.kernel.org/r/1655988119-223714-1-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|/
|
|
|
|
|
|
| |
Properly align comment lines in slot_index_alloc_quirk_v2_hw().
Link: https://lore.kernel.org/r/20220621072405.34394-1-jiangjian@cdjrlc.com
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The memories for the slot should be observed to be written prior to
observing the slot as ready.
Prior to commit 26fc0ea74fcb ("scsi: libsas: Drop SAS_TASK_AT_INITIATOR"),
we had a spin_lock() + spin_unlock() immediately before marking the slot as
ready. The spin_unlock() - with release semantics - caused the slot memory
to be observed to be written.
Now that the spin_lock() + spin_unlock() is gone, use a smp_wmb().
Link: https://lore.kernel.org/r/1652774661-12935-1-git-send-email-john.garry@huawei.com
Fixes: 26fc0ea74fcb ("scsi: libsas: Drop SAS_TASK_AT_INITIATOR")
Reported-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Removing an ATA device via sysfs means that the device may not be found
through re-scanning:
root@ubuntu:/home/john# lsscsi
[0:0:0:0] disk SanDisk LT0200MO P404 /dev/sda
[0:0:1:0] disk ATA HGST HUS724040AL A8B0 /dev/sdb
[0:0:8:0] enclosu 12G SAS Expander RevB -
root@ubuntu:/home/john# echo 1 > /sys/block/sdb/device/delete
root@ubuntu:/home/john# echo "- - -" > /sys/class/scsi_host/host0/scan
root@ubuntu:/home/john# lsscsi
[0:0:0:0] disk SanDisk LT0200MO P404 /dev/sda
[0:0:8:0] enclosu 12G SAS Expander RevB -
root@ubuntu:/home/john#
The problem is that the rescan of the device may conflict with the device
in being re-initialized, as follows:
- In the rescan we call hisi_sas_slave_alloc() in store_scan() ->
sas_user_scan() -> [__]scsi_scan_target() -> scsi_probe_and_add_lunc()
-> scsi_alloc_sdev() -> hisi_sas_slave_alloc() -> hisi_sas_init_device()
In hisi_sas_init_device() we issue an IT nexus reset for ATA devices
- That IT nexus causes the remote PHY to go down and this triggers a bcast
event
- In parallel libsas processes the bcast event, finds that the phy is down
and marks the device as gone
The hard reset issued in hisi_sas_init_device() is unncessary - as
described in the code comment - so remove it. Also set dev status as
HISI_SAS_DEV_NORMAL as the hisi_sas_init_device() call.
Link: https://lore.kernel.org/r/1652354134-171343-4-git-send-email-john.garry@huawei.com
Fixes: 36c6b7613ef1 ("scsi: hisi_sas: Initialise devices in .slave_alloc callback")
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We have seen errors like this when a SATA device is probed:
[524.566298] hisi_sas_v3_hw 0000L74:02.0: erroneous completion iptt=4096 ...
[524.582827] sas: TMF task open reject failed 500e004aaaaaaaa00
Since commit 21c7e972475e ("scsi: hisi_sas: Disable SATA disk phy for
severe I_T nexus reset failure"), we issue an ATA softreset to disks after
a phy reset to ensure that they are in sound working order. If the
softreset is issued before the remote phy has come back up then the
softreset will fail (errors as above). Remedy this by waiting for the phy
to come back up after the reset.
Link: https://lore.kernel.org/r/1652354134-171343-3-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
If we fail to notify the phy up event then undo the RPM resume, as the phy
up notify event handling pairs with that RPM resume.
Link: https://lore.kernel.org/r/1651839939-101188-1-git-send-email-john.garry@huawei.com
Reported-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
| |
This case statement doesn't fall through any more so remove the fallthrough
annotation.
Link: https://lore.kernel.org/r/20220317075214.GC25237@kili
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Use the common libsas internal abort functionality.
In addition, this driver has special handling for internal abort timeouts -
specifically whether to reset the controller in that instance, so extend
the API for that.
Timeout is now increased to 20 * Hz from 6 * Hz.
We also retry for failure now, but this should not make a difference.
Link: https://lore.kernel.org/r/1647001432-239276-5-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|