| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This fixes tx and bi-directional dma transfers on rk3399-gru-kevin.
It seems the SPI fifo must have room for 2 bursts when the dma_tx_req
signal is generated or it might skip some words. This in turn makes
the rx dma channel never complete for bi-directional transfers.
Fix it by setting tx burst length to fifo_len / 4 and the dma
watermark to fifo_len / 2.
However the rk3399 TRM says (sic):
"DMAC support incrementing-address burst and fixed-address burst. But in
the case of access SPI and UART at byte or halfword size, DMAC only
support fixed-address burst and the address must be aligned to word."
So this relies on fifo_len being a multiple of 16 such that the
burst length (= fifo_len / 4) is a multiple of 4 and the addresses
will be word-aligned.
Fixes: dcfc861d24ec ("spi: rockchip: adjust dma watermark and burstlen")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
| |
Add missing support for lsb-first mode.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
| |
The hardware supports 4, 8 and 16bit spi words,
so add the missing support for 4bit words.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
| |
Register an interrupt handler to fill/empty the
tx and rx fifos rather than busy-looping.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
| |
Now that we no longer potentially change spi clock
at runtime we can precompute the rx sample delay
at probe time rather than for each transfer.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The driver previously checked each transfer if the
requested speed was higher than possible with the
current spi clock rate and raised the clock rate
accordingly.
However, there is no check to see if the spi clock
was actually set that high and no way to dynamically
lower the spi clock rate again.
So it seems any potiential users of this functionality
are better off just setting the spi clock rate at init
using the assigned-clock-rates devicetree property.
Removing this dynamic spi clock rate raising allows
us let the spi framework handle min/max speeds
for us.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
| |
We only need to know if we're using dma when setting
up the transfer, so just use a local variable for
that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In almost all cases we already have a pointer to the
spi master structure where we have the driver data.
The only exceptions are the dma callbacks which are
easily fixed by passing them the master and using
spi_master_get_devdata to retrieve the driver data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
| |
The spi master (aka spi controller) structure already
has two fields for storing the rx and tx dma channels.
Just use them rather than duplicating them in driver data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
| |
Just read transfer info directly from the spi device
and transfer structures rather than storing it in
driver data first.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Successful transfers leave the spi disabled, so if
we just make sure to disable the spi on error
there should be no need to disable the spi from
master->unprepare_message.
This also flushes the tx and rx fifos,
so no need to do that manually.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
The state field is currently only used to make sure
only the last of the tx and rx dma callbacks issue
an spi_finalize_current_transfer.
Rather than using a spinlock we can get away
with just turning the state field into an atomic_t.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
| |
The hardware supports 3 different variants of SPI
and there were some code around it, but nothing
to actually set it to anything but "Motorola SPI".
Just drop that code and always use that mode.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
| |
Use C99 designated initializers for dma slave config
structures. This also makes sure uninitialized fields
are zeroed so we don't need an explicit memset.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
| |
The spi_enable_chip function takes a boolean
argument. Change the type to reflect that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Let the dma/non-dma code paths handle the spi enable
flag themselves. This removes some logic to determine
if the flag should be turned on before or after dma
and also don't leave the spi enabled if the dma path
fails.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The dma direction for the tx and rx dma channels never
change, so just use the constants directly rather
than storing them in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The driver data has a u32 field use_dma which is
only ever used as a boolean, so change its type
to reflect that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We no longer need the dma_caps since the dma driver
already clamps the burst length to the hardware limit,
so don't request and store dma_caps in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Signal tx dma when spi fifo is less than half full,
and limit tx bursts to half the fifo length.
Clamp rx burst length to 1 to avoid alignment issues.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|/
|
|
|
|
|
|
|
|
| |
The rxconf and txconf structs are allocated on the
stack, so make sure we zero them before filling out
the relevant fields.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
| |
CTRLR1 is number of data frames, when rx only.
When data frame is 8 bit, CTRLR1 is len-1.
When data frame is 16 bit, CTRLR1 is (len/2)-1.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
| |
The spi on rv1108 is the same as other rockchip based
socs, add compatible string for it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
The runtime suspend callback might be called by pm domain framework at
suspend_noirq stage. It would try to disable the clocks which already
been disabled by rockchip_spi_suspend.
Call pm_runtime_force_suspend/pm_runtime_force_resume when
suspend/resume to avoid that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
| |
We are assuming clocks enabled when calling rockchip_spi_remove, which
is not always true. Those clocks might already been disabled by the
runtime PM at that time.
Call pm_runtime_get_sync before trying to disable clocks to avoid that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
| |
Slightly rework return value handling, no functional changes.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The rockchip spi would stop driving pins when runtime suspended, which
might break slave's xfer(for example cros_ec).
Since we have pullups on those pins, we only need to care about this
when the CS asserted.
So let's keep the spi alive when chip select is asserted.
Also use pm_runtime_put instead of pm_runtime_put_sync.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
| |
The rockchip spi still requires slave selection when using GPIO CS.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
| |
After failed to request dma tx chain, we need to disable pm_runtime.
Also cleanup error labels for better readability.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
|
|
|
|
| |
In the pattern of many other devices, support a system-sleep pin
configuration.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|\ \
| | |
| | |
| | | |
'spi/topic/s3c64xx', 'spi/topic/sh' and 'spi/topic/sh-msiof' into spi-next
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In gerenal, the "rockchip,rockchip-spi" string will match the dts
that's great in spi driver. After all the most of rockchip SoCs ar
same spi controller.
Then, we should keep the old style to match the dts various.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | |
| \ | |
|\ \ \
| | |/
| |/|
| | | |
spi-linus
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The Rockchip SPI controller's length register only supports 16-bits,
yielding a maximum length of 64KiB (the CTRLR1 register holds "length -
1"). Trying to transfer more than that (e.g., with a large SPI flash
read) will cause the driver to hang.
Now, it seems that while theoretically we should be able to program
CTRLR1 with 0xffff, and get a 64KiB transfer, but that also seems to
cause the core to choke, so stick with a maximum of 64K - 1 bytes --
i.e., 0xffff.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When using DMA, the transfer_one callback should return 1 because the
transfer hasn't finished yet.
A previous commit changed the function to return 0 when the DMA channels
were correctly prepared.
This manifested in Veyron boards with this message:
[ 1.983605] cros-ec-spi spi0.0: EC failed to respond in time
Fixes: ea9849113343 ("spi: rockchip: check return value of dmaengine_prep_slave_sg")
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
|
|
|
|
|
|
|
|
|
|
| |
We were calling dma_release_channel(rs->dma_tx.ch) when "rs->dma_tx.ch"
is potentially NULL. There is actually a call to that in the unwind
code at the bottom of the function so we can just re-arrange this a bit
and remove the call. Also there is no need to set rs->dma_tx.ch to
NULL on this error path.
Fixes: e4c0e06f949b ('spi: rockchip: fix probe deferral handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|\ \
| | |
| | |
| | | |
spi-linus
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Use dma_request_chan instead of dma_request_slave_channel,
in this case we can check EPROBE_DEFER without static
warning.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |/
| |
| |
| |
| | |
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|\ \
| |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull dmaengine updates from Vinod Koul:
"This is smallish update with minor changes to core and new driver and
usual updates. Nothing super exciting here..
- We have made slave address as physical to enable driver to do the
mapping.
- We now expose the maxburst for slave dma as new capability so
clients can know this and program accordingly
- addition of device synchronize callbacks on omap and edma.
- pl330 updates to support DMAFLUSHP for Rockchip platforms.
- Updates and improved sg handling in Xilinx VDMA driver.
- New hidma qualcomm dma driver, though some bits are still in
progress"
* tag 'dmaengine-4.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (40 commits)
dmaengine: IOATDMA: revise channel reset workaround on CB3.3 platforms
dmaengine: add Qualcomm Technologies HIDMA channel driver
dmaengine: add Qualcomm Technologies HIDMA management driver
dmaengine: hidma: Add Device Tree binding
dmaengine: qcom_bam_dma: move to qcom directory
dmaengine: tegra: Move of_device_id table near to its user
dmaengine: xilinx_vdma: Remove unnecessary variable initializations
dmaengine: sirf: use __maybe_unused to hide pm functions
dmaengine: rcar-dmac: clear pertinence number of channels
dmaengine: sh: shdmac: don't open code of_device_get_match_data()
dmaengine: tegra: don't open code of_device_get_match_data()
dmaengine: qcom_bam_dma: Make driver work for BE
dmaengine: sun4i: support module autoloading
dma/mic_x100_dma: IS_ERR() vs PTR_ERR() typo
dmaengine: xilinx_vdma: Use readl_poll_timeout instead of do while loop's
dmaengine: xilinx_vdma: Simplify spin lock handling
dmaengine: xilinx_vdma: Fix issues with non-parking mode
dmaengine: xilinx_vdma: Improve SG engine handling
dmaengine: pl330: fix to support the burst mode
dmaengine: make slave address physical
...
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Generic dma controller on Rockchips' platform cannot support
DMAFLUSHP instruction which make dma to flush the req of non-aligned
or non-multiple of what we need. That will cause an unrecoverable
dma bus error. The saftest way is to set dma max burst to 1.
Signed-off-by: Addy ke <addy.ke@rock-chips.com>
Fixes: 64e36824b32b06 ("spi/rockchip: add driver for Rockchip...")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
cc: Heiko Stuebner <heiko@sntech.de>
cc: Olof Johansson <olof@lixom.net>
cc: Doug Anderson <dianders@chromium.org>
cc: Sonny Rao <sonnyrao@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
| | | |
| \ | |
|\ \ \
| | |/
| |/|
| | | |
'spi/topic/sh', 'spi/topic/ti-qspi' and 'spi/topic/xilinx' into spi-next
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
rsd_nsecs is defined as u8 memeber of struct rockchip_spi,
but using of_property_read_u32. That means we take risk of
truncation by type conversion if we pass on big value from
dt.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Remove some of unused header files and reoder
it into alphabetical order.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Let's defer probing the driver if the return value of
dma_request_slave_channel is ERR_PTR(-EPROBE_DEFER) instead
of disabling dma capability directly.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
dmaengine_terminate_all is deprecated, let's use
dmaengine_terminate_async for interrupt handling.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
We should check return value of dmaengine_prep_slave_sg, otherwise
we take risk of null pointer.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
16-bit transfers must be in big endian mode on wire.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Rockchip_spi_set_cs could be called by spi_setup, but
spi_setup may be called by device driver after runtime suspend.
Then the spi clock is closed, rockchip_spi_set_cs may access the
spi registers, which causes cpu block in some socs.
Fixes: 64e36824b32 ("spi/rockchip: add driver for Rockchip RK3xxx")
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|