summaryrefslogtreecommitdiffstats
path: root/drivers/target
Commit message (Collapse)AuthorAgeFilesLines
* target: Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASKNicholas Bellinger2018-01-172-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 1c21a48055a67ceb693e9c2587824a8de60a217c upstream. This patch fixes bug where early se_cmd exceptions that occur before backend execution can result in use-after-free if/when a subsequent ABORT_TASK occurs for the same tag. Since an early se_cmd exception will have had se_cmd added to se_session->sess_cmd_list via target_get_sess_cmd(), it will not have CMD_T_COMPLETE set by the usual target_complete_cmd() backend completion path. This causes a subsequent ABORT_TASK + __target_check_io_state() to signal ABORT_TASK should proceed. As core_tmr_abort_task() executes, it will bring the outstanding se_cmd->cmd_kref count down to zero releasing se_cmd, after se_cmd has already been queued with error status into fabric driver response path code. To address this bug, introduce a CMD_T_PRE_EXECUTE bit that is set at target_get_sess_cmd() time, and cleared immediately before backend driver dispatch in target_execute_cmd() once CMD_T_ACTIVE is set. Then, check CMD_T_PRE_EXECUTE within __target_check_io_state() to determine when an early exception has occured, and avoid aborting this se_cmd since it will have already been queued into fabric driver response path code. Reported-by: Donald White <dew@datera.io> Cc: Donald White <dew@datera.io> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* iscsi-target: Make TASK_REASSIGN use proper se_cmd->cmd_krefNicholas Bellinger2018-01-171-14/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit ae072726f6109bb1c94841d6fb3a82dde298ea85 upstream. Since commit 59b6986dbf fixed a potential NULL pointer dereference by allocating a se_tmr_req for ISCSI_TM_FUNC_TASK_REASSIGN, the se_tmr_req is currently leaked by iscsit_free_cmd() because no iscsi_cmd->se_cmd.se_tfo was associated. To address this, treat ISCSI_TM_FUNC_TASK_REASSIGN like any other TMR and call transport_init_se_cmd() + target_get_sess_cmd() to setup iscsi_cmd->se_cmd.se_tfo with se_cmd->cmd_kref of 2. This will ensure normal release operation once se_cmd->cmd_kref reaches zero and target_release_cmd_kref() is invoked, se_tmr_req will be released via existing target_free_cmd_mem() and core_tmr_release_req() code. Reported-by: Donald White <dew@datera.io> Cc: Donald White <dew@datera.io> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target/file: Do not return error for UNMAP if length is zeroJiang Yi2017-12-201-0/+4
| | | | | | | | | | | | | | | | | [ Upstream commit 594e25e73440863981032d76c9b1e33409ceff6e ] The function fd_execute_unmap() in target_core_file.c calles ret = file->f_op->fallocate(file, mode, pos, len); Some filesystems implement fallocate() to return error if length is zero (e.g. btrfs) but according to SCSI Block Commands spec UNMAP should return success for zero length. Signed-off-by: Jiang Yi <jiangyilism@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target:fix condition return in core_pr_dump_initiator_port()tangwenji2017-12-201-1/+3
| | | | | | | | | | | | | | | | | | | [ Upstream commit 24528f089d0a444070aa4f715ace537e8d6bf168 ] When is pr_reg->isid_present_at_reg is false,this function should return. This fixes a regression originally introduced by: commit d2843c173ee53cf4c12e7dfedc069a5bc76f0ac5 Author: Andy Grover <agrover@redhat.com> Date: Thu May 16 10:40:55 2013 -0700 target: Alter core_pr_dump_initiator_port for ease of use Signed-off-by: tangwenji <tang.wenji@zte.com.cn> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* iscsi-target: fix memory leak in lio_target_tiqn_addtpg()tangwenji2017-12-201-1/+2
| | | | | | | | | | | [ Upstream commit 12d5a43b2dffb6cd28062b4e19024f7982393288 ] tpg must free when call core_tpg_register() return fail Signed-off-by: tangwenji <tang.wenji@zte.com.cn> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target/iscsi: Fix a race condition in iscsit_add_reject_from_cmd()Bart Van Assche2017-12-201-1/+2
| | | | | | | | | | | | | | | [ Upstream commit cfe2b621bb18d86e93271febf8c6e37622da2d14 ] Avoid that cmd->se_cmd.se_tfo is read after a command has already been freed. Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Mike Christie <mchristi@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target: Use system workqueue for ALUA transitionsMike Christie2017-12-201-5/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 207ee84133c00a8a2a5bdec94df4a5b37d78881c ] If tcmu-runner is processing a STPG and needs to change the kernel's ALUA state then we cannot use the same work queue for task management requests and ALUA transitions, because we could deadlock. The problem occurs when a STPG times out before tcmu-runner is able to call into target_tg_pt_gp_alua_access_state_store-> core_alua_do_port_transition -> core_alua_do_transition_tg_pt -> queue_work. In this case, the tmr is on the work queue waiting for the STPG to complete, but the STPG transition is now queued behind the waiting tmr. Note: This bug will also be fixed by this patch: http://www.spinics.net/lists/target-devel/msg14560.html which switches the tmr code to use the system workqueues. For both, I am not sure if we need a dedicated workqueue since it is not a performance path and I do not think we need WQ_MEM_RECLAIM to make forward progress to free up memory like the block layer does. Signed-off-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* iscsi-target: Fix non-immediate TMR reference leakNicholas Bellinger2017-11-301-3/+5
| | | | | | | | | | | | | | | | | | | commit 3fc9fb13a4b2576aeab86c62fd64eb29ab68659c upstream. This patch fixes a se_cmd->cmd_kref reference leak that can occur when a non immediate TMR is proceeded our of command sequence number order, and CMDSN_LOWER_THAN_EXP is returned by iscsit_sequence_cmd(). To address this bug, call target_put_sess_cmd() during this special case following what iscsit_process_scsi_cmd() does upon CMDSN_LOWER_THAN_EXP. Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* iscsi-target: Fix iscsi_np reset hung task during parallel deleteNicholas Bellinger2017-11-213-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 978d13d60c34818a41fc35962602bdfa5c03f214 upstream. This patch fixes a bug associated with iscsit_reset_np_thread() that can occur during parallel configfs rmdir of a single iscsi_np used across multiple iscsi-target instances, that would result in hung task(s) similar to below where configfs rmdir process context was blocked indefinately waiting for iscsi_np->np_restart_comp to finish: [ 6726.112076] INFO: task dcp_proxy_node_:15550 blocked for more than 120 seconds. [ 6726.119440] Tainted: G W O 4.1.26-3321 #2 [ 6726.125045] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 6726.132927] dcp_proxy_node_ D ffff8803f202bc88 0 15550 1 0x00000000 [ 6726.140058] ffff8803f202bc88 ffff88085c64d960 ffff88083b3b1ad0 ffff88087fffeb08 [ 6726.147593] ffff8803f202c000 7fffffffffffffff ffff88083f459c28 ffff88083b3b1ad0 [ 6726.155132] ffff88035373c100 ffff8803f202bca8 ffffffff8168ced2 ffff8803f202bcb8 [ 6726.162667] Call Trace: [ 6726.165150] [<ffffffff8168ced2>] schedule+0x32/0x80 [ 6726.170156] [<ffffffff8168f5b4>] schedule_timeout+0x214/0x290 [ 6726.176030] [<ffffffff810caef2>] ? __send_signal+0x52/0x4a0 [ 6726.181728] [<ffffffff8168d7d6>] wait_for_completion+0x96/0x100 [ 6726.187774] [<ffffffff810e7c80>] ? wake_up_state+0x10/0x10 [ 6726.193395] [<ffffffffa035d6e2>] iscsit_reset_np_thread+0x62/0xe0 [iscsi_target_mod] [ 6726.201278] [<ffffffffa0355d86>] iscsit_tpg_disable_portal_group+0x96/0x190 [iscsi_target_mod] [ 6726.210033] [<ffffffffa0363f7f>] lio_target_tpg_store_enable+0x4f/0xc0 [iscsi_target_mod] [ 6726.218351] [<ffffffff81260c5a>] configfs_write_file+0xaa/0x110 [ 6726.224392] [<ffffffff811ea364>] vfs_write+0xa4/0x1b0 [ 6726.229576] [<ffffffff811eb111>] SyS_write+0x41/0xb0 [ 6726.234659] [<ffffffff8169042e>] system_call_fastpath+0x12/0x71 It would happen because each iscsit_reset_np_thread() sets state to ISCSI_NP_THREAD_RESET, sends SIGINT, and then blocks waiting for completion on iscsi_np->np_restart_comp. However, if iscsi_np was active processing a login request and more than a single iscsit_reset_np_thread() caller to the same iscsi_np was blocked on iscsi_np->np_restart_comp, iscsi_np kthread process context in __iscsi_target_login_thread() would flush pending signals and only perform a single completion of np->np_restart_comp before going back to sleep within transport specific iscsit_transport->iscsi_accept_np code. To address this bug, add a iscsi_np->np_reset_count and update __iscsi_target_login_thread() to keep completing np->np_restart_comp until ->np_reset_count has reached zero. Reported-by: Gary Guo <ghg@datera.io> Tested-by: Gary Guo <ghg@datera.io> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target/iscsi: Fix iSCSI task reassignment handlingBart Van Assche2017-11-181-12/+7
| | | | | | | | | | | | | | | | | | | commit 59b6986dbfcdab96a971f9663221849de79a7556 upstream. Allocate a task management request structure for all task management requests, including task reassignment. This change avoids that the se_tmr->response assignment dereferences an uninitialized se_tmr pointer. Reported-by: Moshe David <mdavid@infinidat.com> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Moshe David <mdavid@infinidat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target/iscsi: Fix unsolicited data seq_end_offset calculationVarun Prakash2017-10-211-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 4d65491c269729a1e3b375c45e73213f49103d33 ] In case of unsolicited data for the first sequence seq_end_offset must be set to minimum of total data length and FirstBurstLength, so do not add cmd->write_data_done to the min of total data length and FirstBurstLength. This patch avoids that with ImmediateData=Yes, InitialR2T=No, MaxXmitDataSegmentLength < FirstBurstLength that a WRITE command with IO size above FirstBurstLength triggers sequence error messages, for example Set following parameters on target (linux-4.8.12) ImmediateData = Yes InitialR2T = No MaxXmitDataSegmentLength = 8k FirstBurstLength = 64k Log in from Open iSCSI initiator and execute dd if=/dev/zero of=/dev/sdb bs=128k count=1 oflag=direct Error messages on target Command ITT: 0x00000035 with Offset: 65536, Length: 8192 outside of Sequence 73728:131072 while DataSequenceInOrder=Yes. Command ITT: 0x00000035, received DataSN: 0x00000001 higher than expected 0x00000000. Unable to perform within-command recovery while ERL=0. Signed-off-by: Varun Prakash <varun@chelsio.com> [ bvanassche: Use min() instead of open-coding it / edited patch description ] Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* iscsi-target: Fix delayed logout processing greater than SECONDS_FOR_LOGOUT_COMPNicholas Bellinger2017-08-111-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 105fa2f44e504c830697b0c794822112d79808dc upstream. This patch fixes a BUG() in iscsit_close_session() that could be triggered when iscsit_logout_post_handler() execution from within tx thread context was not run for more than SECONDS_FOR_LOGOUT_COMP (15 seconds), and the TCP connection didn't already close before then forcing tx thread context to automatically exit. This would manifest itself during explicit logout as: [33206.974254] 1 connection(s) still exist for iSCSI session to iqn.1993-08.org.debian:01:3f5523242179 [33206.980184] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 2100.772 msecs [33209.078643] ------------[ cut here ]------------ [33209.078646] kernel BUG at drivers/target/iscsi/iscsi_target.c:4346! Normally when explicit logout attempt fails, the tx thread context exits and iscsit_close_connection() from rx thread context does the extra cleanup once it detects conn->conn_logout_remove has not been cleared by the logout type specific post handlers. To address this special case, if the logout post handler in tx thread context detects conn->tx_thread_active has already been cleared, simply return and exit in order for existing iscsit_close_connection() logic from rx thread context do failed logout cleanup. Reported-by: Bart Van Assche <bart.vanassche@sandisk.com> Tested-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Sagi Grimberg <sagig@mellanox.com> Tested-by: Gary Guo <ghg@datera.io> Tested-by: Chu Yuan Lin <cyl@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* iscsi-target: Fix initial login PDU asynchronous socket close OOPsNicholas Bellinger2017-08-112-67/+138
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 25cdda95fda78d22d44157da15aa7ea34be3c804 upstream. This patch fixes a OOPs originally introduced by: commit bb048357dad6d604520c91586334c9c230366a14 Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Sep 5 14:54:04 2013 -0700 iscsi-target: Add sk->sk_state_change to cleanup after TCP failure which would trigger a NULL pointer dereference when a TCP connection was closed asynchronously via iscsi_target_sk_state_change(), but only when the initial PDU processing in iscsi_target_do_login() from iscsi_np process context was blocked waiting for backend I/O to complete. To address this issue, this patch makes the following changes. First, it introduces some common helper functions used for checking socket closing state, checking login_flags, and atomically checking socket closing state + setting login_flags. Second, it introduces a LOGIN_FLAGS_INITIAL_PDU bit to know when a TCP connection has dropped via iscsi_target_sk_state_change(), but the initial PDU processing within iscsi_target_do_login() in iscsi_np context is still running. For this case, it sets LOGIN_FLAGS_CLOSED, but doesn't invoke schedule_delayed_work(). The original NULL pointer dereference case reported by MNC is now handled by iscsi_target_do_login() doing a iscsi_target_sk_check_close() before transitioning to FFP to determine when the socket has already closed, or iscsi_target_start_negotiation() if the login needs to exchange more PDUs (eg: iscsi_target_do_login returned 0) but the socket has closed. For both of these cases, the cleanup up of remaining connection resources will occur in iscsi_target_start_negotiation() from iscsi_np process context once the failure is detected. Finally, to handle to case where iscsi_target_sk_state_change() is called after the initial PDU procesing is complete, it now invokes conn->login_work -> iscsi_target_do_login_rx() to perform cleanup once existing iscsi_target_sk_check_close() checks detect connection failure. For this case, the cleanup of remaining connection resources will occur in iscsi_target_do_login_rx() from delayed workqueue process context once the failure is detected. Reported-by: Mike Christie <mchristi@redhat.com> Reviewed-by: Mike Christie <mchristi@redhat.com> Tested-by: Mike Christie <mchristi@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Reported-by: Hannes Reinecke <hare@suse.com> Cc: Hannes Reinecke <hare@suse.com> Cc: Sagi Grimberg <sagi@grimberg.me> Cc: Varun Prakash <varun@chelsio.com> Cc: <stable@vger.kernel.org> # v3.12+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* iscsi-target: Fix early sk_data_ready LOGIN_FLAGS_READY raceNicholas Bellinger2017-08-111-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 8f0dfb3d8b1120c61f6e2cc3729290db10772b2d upstream. There is a iscsi-target/tcp login race in LOGIN_FLAGS_READY state assignment that can result in frequent errors during iscsi discovery: "iSCSI Login negotiation failed." To address this bug, move the initial LOGIN_FLAGS_READY assignment ahead of iscsi_target_do_login() when handling the initial iscsi_target_start_negotiation() request PDU during connection login. As iscsi_target_do_login_rx() work_struct callback is clearing LOGIN_FLAGS_READ_ACTIVE after subsequent calls to iscsi_target_do_login(), the early sk_data_ready ahead of the first iscsi_target_do_login() expects LOGIN_FLAGS_READY to also be set for the initial login request PDU. As reported by Maged, this was first obsered using an MSFT initiator running across multiple VMWare host virtual machines with iscsi-target/tcp. Reported-by: Maged Mokhtar <mmokhtar@binarykinetics.com> Tested-by: Maged Mokhtar <mmokhtar@binarykinetics.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* iscsi-target: Always wait for kthread_should_stop() before kthread exitJiang Yi2017-08-114-8/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 5e0cf5e6c43b9e19fc0284f69e5cd2b4a47523b0 upstream. There are three timing problems in the kthread usages of iscsi_target_mod: - np_thread of struct iscsi_np - rx_thread and tx_thread of struct iscsi_conn In iscsit_close_connection(), it calls send_sig(SIGINT, conn->tx_thread, 1); kthread_stop(conn->tx_thread); In conn->tx_thread, which is iscsi_target_tx_thread(), when it receive SIGINT the kthread will exit without checking the return value of kthread_should_stop(). So if iscsi_target_tx_thread() exit right between send_sig(SIGINT...) and kthread_stop(...), the kthread_stop() will try to stop an already stopped kthread. This is invalid according to the documentation of kthread_stop(). (Fix -ECONNRESET logout handling in iscsi_target_tx_thread and early iscsi_target_rx_thread failure case - nab) Signed-off-by: Jiang Yi <jiangyilism@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target: Avoid mappedlun symlink creation during lun shutdownNicholas Bellinger2017-08-112-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 49cb77e297dc611a1b795cfeb79452b3002bd331 upstream. This patch closes a race between se_lun deletion during configfs unlink in target_fabric_port_unlink() -> core_dev_del_lun() -> core_tpg_remove_lun(), when transport_clear_lun_ref() blocks waiting for percpu_ref RCU grace period to finish, but a new NodeACL mappedlun is added before the RCU grace period has completed. This can happen in target_fabric_mappedlun_link() because it only checks for se_lun->lun_se_dev, which is not cleared until after transport_clear_lun_ref() percpu_ref RCU grace period finishes. This bug originally manifested as NULL pointer dereference OOPsen in target_stat_scsi_att_intr_port_show_attr_dev() on v4.1.y code, because it dereferences lun->lun_se_dev without a explicit NULL pointer check. In post v4.1 code with target-core RCU conversion, the code in target_stat_scsi_att_intr_port_show_attr_dev() no longer uses se_lun->lun_se_dev, but the same race still exists. To address the bug, go ahead and set se_lun>lun_shutdown as early as possible in core_tpg_remove_lun(), and ensure new NodeACL mappedlun creation in target_fabric_mappedlun_link() fails during se_lun shutdown. Reported-by: James Shen <jcs@datera.io> Cc: James Shen <jcs@datera.io> Tested-by: James Shen <jcs@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target: Fix COMPARE_AND_WRITE caw_sem leak during se_cmd quiesceJiang Yi2017-07-271-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | commit 1d6ef276594a781686058802996e09c8550fd767 upstream. This patch addresses a COMPARE_AND_WRITE se_device->caw_sem leak, that would be triggered during normal se_cmd shutdown or abort via __transport_wait_for_tasks(). This would occur because target_complete_cmd() would catch this early and do complete_all(&cmd->t_transport_stop_comp), but since target_complete_ok_work() or target_complete_failure_work() are never called to invoke se_cmd->transport_complete_callback(), the COMPARE_AND_WRITE specific callbacks never release caw_sem. To address this special case, go ahead and release caw_sem directly from target_complete_cmd(). (Remove '&& success' from check, to release caw_sem regardless of scsi_status - nab) Signed-off-by: Jiang Yi <jiangyilism@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target: Fix kref->refcount underflow in transport_cmd_finish_abortNicholas Bellinger2017-06-293-12/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 73d4e580ccc5c3e05cea002f18111f66c9c07034 upstream. This patch fixes a se_cmd->cmd_kref underflow during CMD_T_ABORTED when a fabric driver drops it's second reference from below the target_core_tmr.c based callers of transport_cmd_finish_abort(). Recently with the conversion of kref to refcount_t, this bug was manifesting itself as: [705519.601034] refcount_t: underflow; use-after-free. [705519.604034] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 20116.512 msecs [705539.719111] ------------[ cut here ]------------ [705539.719117] WARNING: CPU: 3 PID: 26510 at lib/refcount.c:184 refcount_sub_and_test+0x33/0x51 Since the original kref atomic_t based kref_put() didn't check for underflow and only invoked the final callback when zero was reached, this bug did not manifest in practice since all se_cmd memory is using preallocated tags. To address this, go ahead and propigate the existing return from transport_put_cmd() up via transport_cmd_finish_abort(), and change transport_cmd_finish_abort() + core_tmr_handle_tas_abort() callers to only do their local target_put_sess_cmd() if necessary. Reported-by: Bart Van Assche <bart.vanassche@sandisk.com> Tested-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Tested-by: Gary Guo <ghg@datera.io> Tested-by: Chu Yuan Lin <cyl@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target/fileio: Fix zero-length READ and WRITE handlingBart Van Assche2017-05-201-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 59ac9c078141b8fd0186c0b18660a1b2c24e724e upstream. This patch fixes zero-length READ and WRITE handling in target/FILEIO, which was broken a long time back by: Since: commit d81cb44726f050d7cf1be4afd9cb45d153b52066 Author: Paolo Bonzini <pbonzini@redhat.com> Date: Mon Sep 17 16:36:11 2012 -0700 target: go through normal processing for all zero-length commands which moved zero-length READ and WRITE completion out of target-core, to doing submission into backend driver code. To address this, go ahead and invoke target_complete_cmd() for any non negative return value in fd_do_rw(). Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Andy Grover <agrover@redhat.com> Cc: David Disseldorp <ddiss@suse.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target: Fix VERIFY_16 handling in sbc_parse_cdbMax Lohrmann2017-04-221-2/+8
| | | | | | | | | | | | | | | | | | commit 13603685c1f12c67a7a2427f00b63f39a2b6f7c9 upstream. As reported by Max, the Windows 2008 R2 chkdsk utility expects VERIFY_16 to be supported, and does not handle the returned CHECK_CONDITION properly, resulting in an infinite loop. The kernel will log huge amounts of this error: kernel: TARGET_CORE[iSCSI]: Unsupported SCSI Opcode 0x8f, sending CHECK_CONDITION. Signed-off-by: Max Lohrmann <post@wickenrode.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target/pscsi: Fix TYPE_TAPE + TYPE_MEDIMUM_CHANGER exportNicholas Bellinger2017-04-221-35/+12
| | | | | | | | | | | | | | | | | | | | | | | commit a04e54f2c35823ca32d56afcd5cea5b783e2f51a upstream. The following fixes a divide by zero OOPs with TYPE_TAPE due to pscsi_tape_read_blocksize() failing causing a zero sd->sector_size being propigated up via dev_attrib.hw_block_size. It also fixes another long-standing bug where TYPE_TAPE and TYPE_MEDIMUM_CHANGER where using pscsi_create_type_other(), which does not call scsi_device_get() to take the device reference. Instead, rename pscsi_create_type_rom() to pscsi_create_type_nondisk() and use it for all cases. Finally, also drop a dump_stack() in pscsi_get_blocks() for non TYPE_DISK, which in modern target-core can get invoked via target_sense_desc_format() during CHECK_CONDITION. Reported-by: Malcolm Haak <insanemal@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* iscsi-target: Drop work-around for legacy GlobalSAN initiatorNicholas Bellinger2017-04-221-16/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 1c99de981f30b3e7868b8d20ce5479fa1c0fea46 upstream. Once upon a time back in 2009, a work-around was added to support the GlobalSAN iSCSI initiator v3.3 for MacOSX, which during login did not propose nor respond to MaxBurstLength, FirstBurstLength, DefaultTime2Wait and DefaultTime2Retain keys. The work-around in iscsi_check_proposer_for_optional_reply() allowed the missing keys to be proposed, but did not require waiting for a response before moving to full feature phase operation. This allowed GlobalSAN v3.3 to work out-of-the box, and for many years we didn't run into login interopt issues with any other initiators.. Until recently, when Martin tried a QLogic 57840S iSCSI Offload HBA on Windows 2016 which completed login, but subsequently failed with: Got unknown iSCSI OpCode: 0x43 The issue was QLogic MSFT side did not propose DefaultTime2Wait + DefaultTime2Retain, so LIO proposes them itself, and immediately transitions to full feature phase because of the GlobalSAN hack. However, the QLogic MSFT side still attempts to respond to DefaultTime2Retain + DefaultTime2Wait, even though LIO has set ISCSI_FLAG_LOGIN_NEXT_STAGE3 + ISCSI_FLAG_LOGIN_TRANSIT in last login response. So while the QLogic MSFT side should have been proposing these two keys to start, it was doing the correct thing per RFC-3720 attempting to respond to proposed keys before transitioning to full feature phase. All that said, recent versions of GlobalSAN iSCSI (v5.3.0.541) does correctly propose the four keys during login, making the original work-around moot. So in order to allow QLogic MSFT to run unmodified as-is, go ahead and drop this long standing work-around. Reported-by: Martin Svec <martin.svec@zoner.cz> Cc: Martin Svec <martin.svec@zoner.cz> Cc: Himanshu Madhani <Himanshu.Madhani@cavium.com> Cc: Arun Easi <arun.easi@cavium.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* iscsi-target: Fix TMR reference leak during session shutdownNicholas Bellinger2017-04-221-5/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit efb2ea770bb3b0f40007530bc8b0c22f36e1c5eb upstream. This patch fixes a iscsi-target specific TMR reference leak during session shutdown, that could occur when a TMR was quiesced before the hand-off back to iscsi-target code via transport_cmd_check_stop_to_fabric(). The reference leak happens because iscsit_free_cmd() was incorrectly skipping the final target_put_sess_cmd() for TMRs when transport_generic_free_cmd() returned zero because the se_cmd->cmd_kref did not reach zero, due to the missing se_cmd assignment in original code. The result was iscsi_cmd and it's associated se_cmd memory would be freed once se_sess->sess_cmd_map where released, but the associated se_tmr_req was leaked and remained part of se_device->dev_tmr_list. This bug would manfiest itself as kernel paging request OOPsen in core_tmr_lun_reset(), when a left-over se_tmr_req attempted to dereference it's se_cmd pointer that had already been released during normal session shutdown. To address this bug, go ahead and treat ISCSI_OP_SCSI_CMD and ISCSI_OP_SCSI_TMFUNC the same when there is an extra se_cmd->cmd_kref to drop in iscsit_free_cmd(), and use op_scsi to signal __iscsit_free_cmd() when the former needs to clear any further iscsi related I/O state. Reported-by: Rob Millner <rlm@daterainc.com> Cc: Rob Millner <rlm@daterainc.com> Reported-by: Chu Yuan Lin <cyl@datera.io> Cc: Chu Yuan Lin <cyl@datera.io> Tested-by: Chu Yuan Lin <cyl@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* target/user: Fix use-after-free of tcmu_cmds if they are expiredAndy Grover2017-01-151-2/+0
| | | | | | | | | | | | | | | | | | [ Upstream commit d0905ca757bc40bd1ebc261a448a521b064777d7 ] Don't free the cmd in tcmu_check_expired_cmd, it's still referenced by an entry in our cmd_id->cmd idr. If userspace ever resumes processing, tcmu_handle_completions() will use the now-invalid cmd pointer. Instead, don't free cmd. It will be freed by tcmu_handle_completion() if userspace ever recovers, or tcmu_free_device if not. Cc: stable@vger.kernel.org Reported-by: Bryant G Ly <bgly@us.ibm.com> Tested-by: Bryant G Ly <bgly@us.ibm.com> Signed-off-by: Andy Grover <agrover@redhat.com> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
* target: Don't override EXTENDED_COPY xcopy_pt_cmd SCSI status codeDinesh Israni2016-11-231-3/+12
| | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 926317de33998c112c5510301868ea9aa34097e2 ] This patch addresses a bug where a local EXTENDED_COPY WRITE or READ backend I/O request would always return SAM_STAT_CHECK_CONDITION, even if underlying xcopy_pt_cmd->se_cmd generated a different SCSI status code. ESX host environments expect to hit SAM_STAT_RESERVATION_CONFLICT for certain scenarios, and SAM_STAT_CHECK_CONDITION results in non-retriable status for these cases. Tested on v4.1.y with ESX v5.5u2+ with local IBLOCK backend copy. Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com> Cc: Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by: Dinesh Israni <ddi@datera.io> Signed-off-by: Dinesh Israni <ddi@datera.io> Cc: Dinesh Israni <ddi@datera.io> Cc: stable@vger.kernel.org # 3.14+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
* iscsi-target: Fix panic when adding second TCP connection to iSCSI sessionFeng Li2016-08-221-2/+3
| | | | | | | | | | | | | | | | | [ Upstream commit 8abc718de6e9e52d8a6bfdb735060554aeae25e4 ] In MC/S scenario, the conn->sess has been set NULL in iscsi_login_non_zero_tsih_s1 when the second connection comes here, then kernel panic. The conn->sess will be assigned in iscsi_login_non_zero_tsih_s2. So we should check whether it's NULL before calling. Signed-off-by: Feng Li <lifeng1519@gmail.com> Tested-by: Sumit Rai <sumit.rai@calsoftinc.com> Cc: stable@vger.kernel.org # 3.14+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
* target: Fix race between iscsi-target connection shutdown + ABORT_TASKNicholas Bellinger2016-08-222-7/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 064cdd2d91c2805d788876082f31cc63506f22c3 ] This patch fixes a race in iscsit_release_commands_from_conn() -> iscsit_free_cmd() -> transport_generic_free_cmd() + wait_for_tasks=1, where CMD_T_FABRIC_STOP could end up being set after the final kref_put() is called from core_tmr_abort_task() context. This results in transport_generic_free_cmd() blocking indefinately on se_cmd->cmd_wait_comp, because the target_release_cmd_kref() check for CMD_T_FABRIC_STOP returns false. To address this bug, make iscsit_release_commands_from_conn() do list_splice and set CMD_T_FABRIC_STOP early while holding iscsi_conn->cmd_lock. Also make iscsit_aborted_task() only remove iscsi_cmd_t if CMD_T_FABRIC_STOP has not already been set. Finally in target_release_cmd_kref(), only honor fabric_stop if CMD_T_ABORTED has been set. Cc: Mike Christie <mchristi@redhat.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: stable@vger.kernel.org # 3.14+ Tested-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
* target: Fix missing complete during ABORT_TASK + CMD_T_FABRIC_STOPNicholas Bellinger2016-08-221-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 5e2c956b8aa24d4f33ff7afef92d409eed164746 ] During transport_generic_free_cmd() with a concurrent TMR ABORT_TASK and shutdown CMD_T_FABRIC_STOP bit set, the caller will be blocked on se_cmd->cmd_wait_stop completion until the final kref_put() -> target_release_cmd_kref() has been invoked to call complete(). However, when ABORT_TASK is completed with FUNCTION_COMPLETE in core_tmr_abort_task(), the aborted se_cmd will have already been removed from se_sess->sess_cmd_list via list_del_init(). This results in target_release_cmd_kref() hitting the legacy list_empty() == true check, invoking ->release_cmd() but skipping complete() to wakeup se_cmd->cmd_wait_stop blocked earlier in transport_generic_free_cmd() code. To address this bug, it's safe to go ahead and drop the original list_empty() check so that fabric_stop invokes the complete() as expected, since list_del_init() can safely be used on a empty list. Cc: Mike Christie <mchristi@redhat.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: stable@vger.kernel.org # 3.14+ Tested-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
* target: Fix target_release_cmd_kref shutdown comp leakHimanshu Madhani2016-04-181-2/+0
| | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 5e47f1985d7107331c3f64fb3ec83d66fd73577e ] This patch fixes an active I/O shutdown bug for fabric drivers using target_wait_for_sess_cmds(), where se_cmd descriptor shutdown would result in hung tasks waiting indefinitely for se_cmd->cmd_wait_comp to complete(). To address this bug, drop the incorrect list_del_init() usage in target_wait_for_sess_cmds() and always complete() during se_cmd target_release_cmd_kref() put, in order to let caller invoke the final fabric release callback into se_cmd->se_tfo->release_cmd() code. Reported-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Tested-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: stable@vger.kernel.org Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target: Drop incorrect ABORT_TASK put for completed commandsNicholas Bellinger2016-03-221-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 7f54ab5ff52fb0b91569bc69c4a6bc5cac1b768d ] This patch fixes a recent ABORT_TASK regression associated with commit febe562c, where a left-over target_put_sess_cmd() would still be called when __target_check_io_state() detected a command has already been completed, and explicit ABORT must be avoided. Note commit febe562c dropped the local kref_get_unless_zero() check in core_tmr_abort_task(), but did not drop this extra corresponding target_put_sess_cmd() in the failure path. So go ahead and drop this now bogus target_put_sess_cmd(), and avoid this potential use-after-free. Reported-by: Dan Lane <dracodan@gmail.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Cc: stable@vger.kernel.org # 3.14+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target: Fix race with SCF_SEND_DELAYED_TAS handlingNicholas Bellinger2016-03-051-11/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 310d3d314be7f0a84011ebdc4bdccbcae9755a87 upstream. This patch fixes a race between setting of SCF_SEND_DELAYED_TAS in transport_send_task_abort(), and check of the same bit in transport_check_aborted_status(). It adds a __transport_check_aborted_status() version that is used by target_execute_cmd() when se_cmd->t_state_lock is held, and a transport_check_aborted_status() wrapper for all other existing callers. Also, it handles the case where the check happens before transport_send_task_abort() gets called. For this, go ahead and set SCF_SEND_DELAYED_TAS early when necessary, and have transport_send_task_abort() send the abort. Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target: Fix remote-port TMR ABORT + se_cmd fabric stopNicholas Bellinger2016-03-052-47/+145
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 0f4a943168f31d29a1701908931acaba518b131a upstream. To address the bug where fabric driver level shutdown of se_cmd occurs at the same time when TMR CMD_T_ABORTED is happening resulting in a -1 ->cmd_kref, this patch adds a CMD_T_FABRIC_STOP bit that is used to determine when TMR + driver I_T nexus shutdown is happening concurrently. It changes target_sess_cmd_list_set_waiting() to obtain se_cmd->cmd_kref + set CMD_T_FABRIC_STOP, and drop local reference in target_wait_for_sess_cmds() and invoke extra target_put_sess_cmd() during Task Aborted Status (TAS) when necessary. Also, it adds a new target_wait_free_cmd() wrapper around transport_wait_for_tasks() for the special case within transport_generic_free_cmd() to set CMD_T_FABRIC_STOP, and is now aware of CMD_T_ABORTED + CMD_T_TAS status bits to know when an extra transport_put_cmd() during TAS is required. Note transport_generic_free_cmd() is expected to block on cmd->cmd_wait_comp in order to follow what iscsi-target expects during iscsi_conn context se_cmd shutdown. Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@daterainc.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target: Fix TAS handling for multi-session se_node_aclsNicholas Bellinger2016-03-051-7/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit ebde1ca5a908b10312db4ecd7553e3ba039319ab upstream. This patch fixes a bug in TMR task aborted status (TAS) handling when multiple sessions are connected to the same target WWPN endpoint and se_node_acl descriptor, resulting in TASK_ABORTED status to not be generated for aborted se_cmds on the remote port. This is due to core_tmr_handle_tas_abort() incorrectly comparing se_node_acl instead of se_session, for which the multi-session case is expected to be sharing the same se_node_acl. Instead, go ahead and update core_tmr_handle_tas_abort() to compare tmr_sess + cmd->se_sess in order to determine if the LUN_RESET was received on a different I_T nexus, and TASK_ABORTED status response needs to be generated. Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target: Fix LUN_RESET active I/O handling for ACK_KREFNicholas Bellinger2016-03-052-55/+76
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit febe562c20dfa8f33bee7d419c6b517986a5aa33 upstream. This patch fixes a NULL pointer se_cmd->cmd_kref < 0 refcount bug during TMR LUN_RESET with active se_cmd I/O, that can be triggered during se_cmd descriptor shutdown + release via core_tmr_drain_state_list() code. To address this bug, add common __target_check_io_state() helper for ABORT_TASK + LUN_RESET w/ CMD_T_COMPLETE checking, and set CMD_T_ABORTED + obtain ->cmd_kref for both cases ahead of last target_put_sess_cmd() after TFO->aborted_task() -> transport_cmd_finish_abort() callback has completed. It also introduces SCF_ACK_KREF to determine when transport_cmd_finish_abort() needs to drop the second extra reference, ahead of calling target_put_sess_cmd() for the final kref_put(&se_cmd->cmd_kref). It also updates transport_cmd_check_stop() to avoid holding se_cmd->t_state_lock while dropping se_cmd device state via target_remove_from_state_list(), now that core_tmr_drain_state_list() is holding the se_device lock while checking se_cmd state from within TMR logic. Finally, move transport_put_cmd() release of SGL + TMR + extended CDB memory into target_free_cmd_mem() in order to avoid potential resource leaks in TMR ABORT_TASK + LUN_RESET code-paths. Also update target_release_cmd_kref() accordingly. Reviewed-by: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target: fix COMPARE_AND_WRITE non zero SGL offset data corruptionJan Engelhardt2016-03-051-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit d94e5a61357a04938ce14d6033b4d33a3c5fd780 ] target_core_sbc's compare_and_write functionality suffers from taking data at the wrong memory location when writing a CAW request to disk when a SGL offset is non-zero. This can happen with loopback and vhost-scsi fabric drivers when SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers. Given the following sample LIO subtopology, % targetcli ls /loopback/ o- loopback ................................. [1 Target] o- naa.6001405ebb8df14a ....... [naa.60014059143ed2b3] o- luns ................................... [2 LUNs] o- lun0 ................ [iblock/ram0 (/dev/ram0)] o- lun1 ................ [iblock/ram1 (/dev/ram1)] % lsscsi -g [3:0:1:0] disk LIO-ORG IBLOCK 4.0 /dev/sdc /dev/sg3 [3:0:1:1] disk LIO-ORG IBLOCK 4.0 /dev/sdd /dev/sg4 the following bug can be observed in Linux 4.3 and 4.4~rc1: % perl -e 'print chr$_ for 0..255,reverse 0..255' >rand % perl -e 'print "\0" x 512' >zero % cat rand >/dev/sdd % sg_compare_and_write -i rand -D zero --lba 0 /dev/sdd % sg_compare_and_write -i zero -D rand --lba 0 /dev/sdd Miscompare reported % hexdump -Cn 512 /dev/sdd 00000000 0f 0e 0d 0c 0b 0a 09 08 07 06 05 04 03 02 01 00 00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 * 00000200 Rather than writing all-zeroes as instructed with the -D file, it corrupts the data in the sector by splicing some of the original bytes in. The page of the first entry of cmd->t_data_sg includes the CDB, and sg->offset is set to a position past the CDB. I presume that sg->offset is also the right choice to use for subsequent sglist members. Signed-off-by: Jan Engelhardt <jengelh@netitwork.de> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target: Fix race for SCF_COMPARE_AND_WRITE_POST checkingNicholas Bellinger2016-03-052-10/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 057085e522f8bf94c2e691a5b76880f68060f8ba ] This patch addresses a race + use after free where the first stage of COMPARE_AND_WRITE in compare_and_write_callback() is rescheduled after the backend sends the secondary WRITE, resulting in second stage compare_and_write_post() callback completing in target_complete_ok_work() before the first can return. Because current code depends on checking se_cmd->se_cmd_flags after return from se_cmd->transport_complete_callback(), this results in first stage having SCF_COMPARE_AND_WRITE_POST set, which incorrectly falls through into second stage CAW processing code, eventually triggering a NULL pointer dereference due to use after free. To address this bug, pass in a new *post_ret parameter into se_cmd->transport_complete_callback(), and depend upon this value instead of ->se_cmd_flags to determine when to return or fall through into ->queue_status() code for CAW. Cc: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* iscsi-target: Fix rx_login_comp hang after login failureNicholas Bellinger2016-03-052-1/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit ca82c2bded29b38d36140bfa1e76a7bbfcade390 ] This patch addresses a case where iscsi_target_do_tx_login_io() fails sending the last login response PDU, after the RX/TX threads have already been started. The case centers around iscsi_target_rx_thread() not invoking allow_signal(SIGINT) before the send_sig(SIGINT, ...) occurs from the failure path, resulting in RX thread hanging indefinately on iscsi_conn->rx_login_comp. Note this bug is a regression introduced by: commit e54198657b65625085834847ab6271087323ffea Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Wed Jul 22 23:14:19 2015 -0700 iscsi-target: Fix iscsit_start_kthreads failure OOPs To address this bug, complete ->rx_login_complete for good measure in the failure path, and immediately return from RX thread context if connection state did not actually reach full feature phase (TARG_CONN_STATE_LOGGED_IN). Cc: Sagi Grimberg <sagig@mellanox.com> Cc: <stable@vger.kernel.org> # v3.10+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target: Fix LUN_RESET active TMR descriptor handlingNicholas Bellinger2016-03-022-1/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit a6d9bb1c9605cd4f44e2d8290dc4d0e88f20292d ] This patch fixes a NULL pointer se_cmd->cmd_kref < 0 refcount bug during TMR LUN_RESET with active TMRs, triggered during se_cmd + se_tmr_req descriptor shutdown + release via core_tmr_drain_tmr_list(). To address this bug, go ahead and obtain a local kref_get_unless_zero(&se_cmd->cmd_kref) for active I/O to set CMD_T_ABORTED, and transport_wait_for_tasks() followed by the final target_put_sess_cmd() to drop the local ->cmd_kref. Also add two new checks within target_tmr_work() to avoid CMD_T_ABORTED -> TFO->queue_tm_rsp() callbacks ahead of invoking the backend -> fabric put in transport_cmd_check_stop_to_fabric(). For good measure, also change core_tmr_release_req() to use list_del_init() ahead of se_tmr_req memory free. Reviewed-by: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Cc: stable@vger.kernel.org # 3.10+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target: Remove first argument of target_{get,put}_sess_cmd()Bart Van Assche2016-03-025-22/+21
| | | | | | | | | | | | | | | | | [ Upstream commit afc16604c06414223478df3e42301ab630b9960a ] The first argument of these two functions is always identical to se_cmd->se_sess. Hence remove the first argument. Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Andy Grover <agrover@redhat.com> Cc: <qla2xxx-upstream@qlogic.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* iscsi-target: Fix potential dead-lock during node acl deleteNicholas Bellinger2016-02-091-1/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 26a99c19f810b2593410899a5b304b21b47428a6 ] This patch is a iscsi-target specific bug-fix for a dead-lock that can occur during explicit struct se_node_acl->acl_group se_session deletion via configfs rmdir(2), when iscsi-target time2retain timer is still active. It changes iscsi-target to obtain se_portal_group->session_lock internally using spin_in_locked() to check for the specific se_node_acl configfs shutdown rmdir(2) case. Note this patch is intended for stable, and the subsequent v4.5-rc patch converts target_core_tpg.c to use proper se_sess->sess_kref reference counting for both se_node_acl deletion + se_node_acl->queue_depth se_session restart. Reported-by:: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <michaelc@cs.wisc.edu> Cc: stable@vger.kernel.org # 3.10+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target/iscsi: Fix np_ip bracket issue by removing np_ipAndy Grover2015-10-276-33/+36
| | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 76c28f1fcfeb42b47f798fe498351ee1d60086ae ] Revert commit 1997e6259, which causes double brackets on ipv6 inaddr_any addresses. Since we have np_sockaddr, if we need a textual representation we can use "%pISc". Change iscsit_add_network_portal() and iscsit_add_np() signatures to remove *ip_str parameter. Fix and extend some comments earlier in the function. Tested to work for :: and ::1 via iscsiadm, previously :: failed, see https://bugzilla.redhat.com/show_bug.cgi?id=1249107 . CC: stable@vger.kernel.org Signed-off-by: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* iscsi-target: Fix iscsit_start_kthreads failure OOPsNicholas Bellinger2015-08-275-32/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit e54198657b65625085834847ab6271087323ffea ] This patch fixes a regression introduced with the following commit in v4.0-rc1 code, where a iscsit_start_kthreads() failure triggers a NULL pointer dereference OOPs: commit 88dcd2dab5c23b1c9cfc396246d8f476c872f0ca Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Feb 26 22:19:15 2015 -0800 iscsi-target: Convert iscsi_thread_set usage to kthread.h To address this bug, move iscsit_start_kthreads() immediately preceeding the transmit of last login response, before signaling a successful transition into full-feature-phase within existing iscsi_target_do_tx_login_io() logic. This ensures that no target-side resource allocation failures can occur after the final login response has been successfully sent. Also, it adds a iscsi_conn->rx_login_comp to allow the RX thread to sleep to prevent other socket related failures until the final iscsi_post_login_handler() call is able to complete. Cc: Sagi Grimberg <sagig@mellanox.com> Cc: <stable@vger.kernel.org> # v3.10+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* iscsi-target: Fix iser explicit logout TX kthread leakNicholas Bellinger2015-08-271-2/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 007d038bdf95ccfe2491d0078be54040d110fd06 ] This patch fixes a regression introduced with the following commit in v4.0-rc1 code, where an explicit iser-target logout would result in ->tx_thread_active being incorrectly cleared by the logout post handler, and subsequent TX kthread leak: commit 88dcd2dab5c23b1c9cfc396246d8f476c872f0ca Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Feb 26 22:19:15 2015 -0800 iscsi-target: Convert iscsi_thread_set usage to kthread.h To address this bug, change iscsit_logout_post_handler_closesession() and iscsit_logout_post_handler_samecid() to only cmpxchg() on ->tx_thread_active for traditional iscsi/tcp connections. This is required because iscsi/tcp connections are invoking logout post handler logic directly from TX kthread context, while iser connections are invoking logout post handler logic from a seperate workqueue context. Cc: Sagi Grimberg <sagig@mellanox.com> Cc: <stable@vger.kernel.org> # v3.10+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* iscsi-target: Fix use-after-free during TPG session shutdownNicholas Bellinger2015-08-271-4/+8
| | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 417c20a9bdd1e876384127cf096d8ae8b559066c ] This patch fixes a use-after-free bug in iscsit_release_sessions_for_tpg() where se_portal_group->session_lock was incorrectly released/re-acquired while walking the active se_portal_group->tpg_sess_list. The can result in a NULL pointer dereference when iscsit_close_session() shutdown happens in the normal path asynchronously to this code, causing a bogus dereference of an already freed list entry to occur. To address this bug, walk the session list checking for the same state as before, but move entries to a local list to avoid dropping the lock while walking the active list. As before, signal using iscsi_session->session_restatement=1 for those list entries to be released locally by iscsit_free_session() code. Reported-by: Sunilkumar Nadumuttlu <sjn@datera.io> Cc: Sunilkumar Nadumuttlu <sjn@datera.io> Cc: <stable@vger.kernel.org> # v3.1+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* iscsi-target: Convert iscsi_thread_set usage to kthread.hNicholas Bellinger2015-08-044-69/+114
| | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 88dcd2dab5c23b1c9cfc396246d8f476c872f0ca ] This patch converts iscsi-target code to use modern kthread.h API callers for creating RX/TX threads for each new iscsi_conn descriptor, and releasing associated RX/TX threads during connection shutdown. This is done using iscsit_start_kthreads() -> kthread_run() to start new kthreads from within iscsi_post_login_handler(), and invoking kthread_stop() from existing iscsit_close_connection() code. Also, convert iscsit_logout_post_handler_closesession() code to use cmpxchg when determing when iscsit_cause_connection_reinstatement() needs to sleep waiting for completion. Reported-by: Sagi Grimberg <sagig@mellanox.com> Tested-by: Sagi Grimberg <sagig@mellanox.com> Cc: Slava Shwartsman <valyushash@gmail.com> Cc: <stable@vger.kernel.org> # v3.10+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target/pscsi: Don't leak scsi_host if hba is VIRTUAL_HOSTAndy Grover2015-06-102-0/+4
| | | | | | | | | | | | | | | [ Upstream commit 5a7125c64def3b21f8147eca8b54949a60963942 ] See https://bugzilla.redhat.com/show_bug.cgi?id=1025672 We need to put() the reference to the scsi host that we got in pscsi_configure_device(). In VIRTUAL_HOST mode it is associated with the dev_virt, not the hba_virt. Signed-off-by: Andy Grover <agrover@redhat.com> Cc: stable@vger.kernel.org # 2.6.38+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target/file: Fix SG table for prot_buf initializationAkinobu Mita2015-05-171-15/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit c836777830428372074d5129ac513e1472c99791 ] In fd_do_prot_rw(), it allocates prot_buf which is used to copy from se_cmd->t_prot_sg by sbc_dif_copy_prot(). The SG table for prot_buf is also initialized by allocating 'se_cmd->t_prot_nents' entries of scatterlist and setting the data length of each entry to PAGE_SIZE at most. However if se_cmd->t_prot_sg contains a clustered entry (i.e. sg->length > PAGE_SIZE), the SG table for prot_buf can't be initialized correctly and sbc_dif_copy_prot() can't copy to prot_buf. (This actually happened with TCM loopback fabric module) As prot_buf is allocated by kzalloc() and it's physically contiguous, we only need a single scatterlist entry. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Cc: <stable@vger.kernel.org> # v3.14+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target/file: Fix UNMAP with DIF protection supportAkinobu Mita2015-05-171-25/+61
| | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 64d240b721b21e266ffde645ec965c3b6d1c551f ] When UNMAP command is issued with DIF protection support enabled, the protection info for the unmapped region is remain unchanged. So READ command for the region causes data integrity failure. This fixes it by invalidating protection info for the unmapped region by filling with 0xff pattern. This change also adds helper function fd_do_prot_fill() in order to reduce code duplication with existing fd_format_prot(). Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Cc: <stable@vger.kernel.org> # v3.14+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabledAkinobu Mita2015-05-171-7/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 38da0f49e8aa1649af397d53f88e163d0e60c058 ] When CONFIG_DEBUG_SG=y and DIF protection support enabled, kernel BUG()s are triggered due to the following two issues: 1) prot_sg is not initialized by sg_init_table(). When CONFIG_DEBUG_SG=y, scatterlist helpers check sg entry has a correct magic value. 2) vmalloc'ed buffer is passed to sg_set_buf(). sg_set_buf() uses virt_to_page() to convert virtual address to struct page, but it doesn't work with vmalloc address. vmalloc_to_page() should be used instead. As prot_buf isn't usually too large, so fix it by allocating prot_buf by kmalloc instead of vmalloc. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Cc: <stable@vger.kernel.org> # v3.14+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
* target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handlingNicholas Bellinger2015-05-172-9/+43
| | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit c8e639852ad720499912acedfd6b072325fd2807 ] This patch fixes a bug for COMPARE_AND_WRITE handling with fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC. It adds the missing allocation for cmd->t_bidi_data_sg within transport_generic_new_cmd() that is used by COMPARE_AND_WRITE for the initial READ payload, even if the fabric is already providing a pre-allocated buffer for cmd->t_data_sg. Also, fix zero-length COMPARE_AND_WRITE handling within the compare_and_write_callback() and target_complete_ok_work() to queue the response, skipping the initial READ. This fixes COMPARE_AND_WRITE emulation with loopback, vhost, and xen-backend fabric drivers using SG_TO_MEM_NOALLOC. Reported-by: Christoph Hellwig <hch@lst.de> Cc: Christoph Hellwig <hch@lst.de> Cc: <stable@vger.kernel.org> # v3.12+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-22 03:21:57 +0000