summaryrefslogtreecommitdiffstats
path: root/drivers/thunderbolt/nhi_regs.h
Commit message (Collapse)AuthorAgeFilesLines
* thunderbolt: Reset USB4 v2 host routerMika Westerberg2023-06-161-7/+12
| | | | | | | | | | | | | USB4 v2 added a bit that can be used to reset the host router so we use this to trigger reset when the driver probes. This will reset the already connected topology as well but doing this simplifies things a lot if for instance the link is already set to asymmetric. We also add a module parameter to prevent this in case of problems. While there rename the REG_HOP_COUNT to REG_CAPS to match the USB4 spec naming better. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* thunderbolt: Clear registers properly when auto clear isn't in useMario Limonciello2023-05-091-0/+2
| | | | | | | | | | | | | | | | When `QUIRK_AUTO_CLEAR_INT` isn't set, interrupt masking should be cleared by writing to Interrupt Mask Clear (IMR) and interrupt status should be cleared properly at shutdown/init. This fixes an error where interrupts are left enabled during resume from hibernation with `CONFIG_USB4=y`. Fixes: 468c49f44759 ("thunderbolt: Disable interrupt auto clear for rings") Cc: stable@vger.kernel.org # v6.3 Reported-by: Takashi Iwai <tiwai@suse.de> Link: https://bugzilla.kernel.org/show_bug.cgi?id=217343 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* thunderbolt: Disable interrupt auto clear for ringsMario Limonciello2023-03-201-2/+4
| | | | | | | | | | | | | | | | | | | | When interrupt auto clear is programmed, any read to the interrupt status register will clear all interrupts. If two interrupts have come in before one can be serviced then this will cause lost interrupts. On AMD USB4 routers this has manifested in odd problems particularly with long strings of control tranfers such as reading the DROM via bit banging. Instead of clearing interrupts automatically, clear the bit corresponding to the given ring's interrupt in the ISR. Fixes: 7a1808f82a37 ("thunderbolt: Handle ring interrupt by reading interrupt status register") Cc: Sanju Mehta <Sanju.Mehta@amd.com> Cc: stable@vger.kernel.org Tested-by: Anson Tsao <anson.tsao@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* thunderbolt: Add support for Intel Ice LakeMika Westerberg2019-08-261-0/+37
| | | | | | | | | | | | | | | | The Thunderbolt controller is integrated into the Ice Lake CPU itself and requires special flows to power it on and off using force power bit in NHI VSEC registers. Runtime PM (RTD3) and Sx flows also differ from the discrete solutions. Now the firmware notifies the driver whether RTD3 entry or exit are possible. The driver is responsible of sending Go2Sx command through link controller mailbox when system enters Sx states (suspend-to-mem/disk). Rest of the ICM firwmare flows follow Titan Ridge. Signed-off-by: Raanan Avargil <raanan.avargil@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com> Tested-by: Mario Limonciello <mario.limonciello@dell.com>
* thunderbolt: Add Intel as copyright holderMika Westerberg2018-10-021-0/+1
| | | | | | | | | | | | | | | Intel has done pretty major changes to the driver and we continue to do so in the future as well. Add Intel as copyright holder of the files we have done changes. While there drop "Cactus Ridge" from the headers because this driver works also with other Thunderbolt controllers. No functional changes intended. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-11-041-0/+1
|\ | | | | | | | | | | | | Files removed in 'net-next' had their license header updated in 'net'. We take the remove from 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
| * License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman2017-11-021-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | thunderbolt: Move ring descriptor flags to thunderbolt.hMika Westerberg2017-10-021-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | A Thunderbolt service driver might need to check if there was an error with the descriptor when in frame mode. We also add two Rx specific error flags RING_DESC_CRC_ERROR and RING_DESC_BUFFER_OVERRUN. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Michael Jamet <michael.jamet@intel.com> Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | thunderbolt: Add support for frame modeMika Westerberg2017-10-021-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When high-speed DMA paths are used to transfer arbitrary data over a Thunderbolt link, DMA rings should be in frame mode instead of raw mode. The latter is used by the control channel (ring 0). In frame mode each data frame can hold up to 4kB payload. This patch modifies the DMA ring code to allow configuring a ring to be in frame mode by passing a new flag (RING_FLAG_FRAME) to the ring when it is allocated. In addition there might be need to enable end-to-end (E2E) workaround for the ring to prevent losing Rx frames in certain situations. We add another flag (RING_FLAG_E2E) that can be used for this purpose. This code is based on the work done by Amir Levy and Michael Jamet. Signed-off-by: Michael Jamet <michael.jamet@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | thunderbolt: Configure interrupt throttling for all interruptsMika Westerberg2017-10-021-0/+2
|/ | | | | | | | | | | | | This will keep the interrupt delivery rate reasonable. The value used here (128 us) is a recommendation from the hardware people. This code is based on the work done by Amir Levy and Michael Jamet. Signed-off-by: Michael Jamet <michael.jamet@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* thunderbolt: Add support for Internal Connection Manager (ICM)Mika Westerberg2017-06-091-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Starting from Intel Falcon Ridge the internal connection manager running on the Thunderbolt host controller has been supporting 4 security levels. One reason for this is to prevent DMA attacks and only allow connecting devices the user trusts. The internal connection manager (ICM) is the preferred way of connecting Thunderbolt devices over software only implementation typically used on Macs. The driver communicates with ICM using special Thunderbolt ring 0 (control channel) messages. In order to handle these messages we add support for the ICM messages to the control channel. The security levels are as follows: none - No security, all tunnels are created automatically user - User needs to approve the device before tunnels are created secure - User need to approve the device before tunnels are created. The device is sent a challenge on future connects to be able to verify it is actually the approved device. dponly - Only Display Port and USB tunnels can be created and those are created automatically. The security levels are typically configurable from the system BIOS and by default it is set to "user" on many systems. In this patch each Thunderbolt device will have either one or two new sysfs attributes: authorized and key. The latter appears for devices that support secure connect. In order to identify the device the user can read identication information, including UUID and name of the device from sysfs and based on that make a decision to authorize the device. The device is authorized by simply writing 1 to the "authorized" sysfs attribute. This is following the USB bus device authorization mechanism. The secure connect requires an additional challenge step (writing 2 to the "authorized" attribute) in future connects when the key has already been stored to the NVM of the device. Non-ICM systems (before Alpine Ridge) continue to use the existing functionality and the security level is set to none. For systems with Alpine Ridge, even on Apple hardware, we will use ICM. This code is based on the work done by Amir Levy and Michael Jamet. Signed-off-by: Michael Jamet <michael.jamet@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andreas Noever <andreas.noever@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* thunderbolt: Add support for NHI mailboxMika Westerberg2017-06-091-0/+11
| | | | | | | | | | | | | | | The host controller includes two sets of registers that are used to communicate with the firmware. Add functions that can be used to access these registers. This code is based on the work done by Amir Levy and Michael Jamet. Signed-off-by: Michael Jamet <michael.jamet@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andreas Noever <andreas.noever@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* thunderbolt: Add MSI-X supportMika Westerberg2017-06-091-0/+9
| | | | | | | | | | | | | | | | | | | Intel Thunderbolt controllers support up to 16 MSI-X vectors. Using MSI-X is preferred over MSI or legacy interrupt and may bring additional performance because there is no need to check the status registers which interrupt was triggered. While there we convert comments in structs tb_ring and tb_nhi to follow kernel-doc format more closely. This code is based on the work done by Amir Levy and Michael Jamet. Signed-off-by: Michael Jamet <michael.jamet@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andreas Noever <andreas.noever@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* thunderbolt: Macro renameAmir Levy2016-11-091-3/+3
| | | | | | | | | | This first patch updates the NHI Thunderbolt controller registers file to reflect that it is not only for Cactus Ridge. No functional change intended. Signed-off-by: Amir Levy <amir.jer.levy@intel.com> Signed-off-by: Andreas Noever <andreas.noever@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* thunderbolt: Add initial cactus ridge NHI supportAndreas Noever2014-06-191-0/+101
Thunderbolt hotplug is supposed to be handled by the firmware. But Apple decided to implement thunderbolt at the operating system level. The firmare only initializes thunderbolt devices that are present at boot time. This driver enables hotplug of thunderbolt of non-chained thunderbolt devices on Apple systems with a cactus ridge controller. This first patch adds the Kconfig file as well the parts of the driver which talk directly to the hardware (that is pci device setup, interrupt handling and RX/TX ring management). Signed-off-by: Andreas Noever <andreas.noever@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>