summaryrefslogtreecommitdiffstats
path: root/drivers/tty/serial/omap-serial.c
Commit message (Collapse)AuthorAgeFilesLines
* tty: omap-serial: Fix initial on-boot RTS GPIO levelRafael Gago2018-01-091-4/+3
| | | | | | | | The rs485 flag "SER_RS485_RTS_AFTER_SEND" was wrongly read from the GPIO flags. This caused the RTS pin to be high during boot. Signed-off-by: Rafael Gago Castano <rgc@hms.se> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: core: Support common rs485 binding for RTS polarityLukas Wunner2017-11-281-2/+5
| | | | | | | | | | | | | | | | | | | | | When a driver invokes the uart_get_rs485_mode() helper, set the RTS polarity to active high by default unless the newly introduced "rs485-rts-active-low" property was specified. imx contains a line to set the default RTS polarity to active high, it is now superfluous and hence deleted. omap-serial historically defaults to active low and supports an "rs485-rts-active-high" property to inverse the polarity. Retain that behavior for compatibility. Cc: Mark Jackson <mpfj@newflow.co.uk> Cc: Michał Oleszczyk <oleszczyk.m@gmail.com> Cc: Rafael Gago Castano <rgc@hms.se> Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: Make retrieval of rs485 properties platform-agnosticLukas Wunner2017-11-281-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit ef838a81dd4d ("serial: Add common rs485 device tree parsing function") consolidated retrieval of rs485 OF properties in a common helper function but did not #ifdef it to CONFIG_OF. The function is therefore included on ACPI platforms as well even though it's not used. On the other hand ACPI platforms with rs485 do exist (e.g. Siemens IOT2040) and they may leverage _DSD to store rs485 properties. Likewise, UART platform devices instantiated from an MFD should be able to specify rs485 properties. In fact, the tty subsystem maintainer had asked for a "generic" function during review of commit ef838a81dd4d: https://marc.info/?l=linux-serial&m=150143441725194&w=4 Thus, instead of constraining the helper to OF platforms, make it platform-agnostic by converting it to device_property_*() functions and renaming it accordingly. In imx.c, move the invocation of uart_get_rs485_mode() from serial_imx_probe_dt() to serial_imx_probe() so that it also gets called for non-OF devices. In omap-serial.c, move its invocation further up within serial_omap_probe_rs485() so that the RTS polarity can be overridden with the driver-specific "rs485-rts-active-high" property once we introduce a generic "rs485-rts-active-low" property. Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: serial: Remove redundant license textGreg Kroah-Hartman2017-11-081-5/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that the SPDX tag is in all tty files, that identifies the license in a specific and legally-defined manner. So the extra GPL text wording can be removed as it is no longer needed at all. This is done on a quest to remove the 700+ different ways that files in the kernel describe the GPL license text. And there's unneeded stuff like the address (sometimes incorrect) for the FSF which is never needed. No copyright headers or other non-license-description text was removed. Cc: Jiri Slaby <jslaby@suse.com> Cc: Eric Anholt <eric@anholt.net> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ray Jui <rjui@broadcom.com> Cc: Scott Branden <sbranden@broadcom.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Helge Deller <deller@gmx.de> Cc: Joachim Eastwood <manabian@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Tobias Klauser <tklauser@distanz.ch> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Pat Gefre <pfg@sgi.com> Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Sylvain Lemieux <slemieux.tyco@gmail.com> Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Andy Gross <andy.gross@linaro.org> Cc: David Brown <david.brown@linaro.org> Cc: "Andreas Färber" <afaerber@suse.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Barry Song <baohua@kernel.org> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Timur Tabi <timur@tabi.org> Cc: Tony Prisk <linux@prisktech.co.nz> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: add SPDX identifiers to all remaining files in drivers/tty/Greg Kroah-Hartman2017-11-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's good to have SPDX identifiers in all files to make it easier to audit the kernel tree for correct licenses. Update the drivers/tty files files with the correct SPDX license identifier based on the license text in the file itself. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This work is based on a script and data from Thomas Gleixner, Philippe Ombredanne, and Kate Stewart. Cc: Jiri Slaby <jslaby@suse.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: David Sterba <dsterba@suse.com> Cc: James Hogan <jhogan@kernel.org> Cc: Rob Herring <robh@kernel.org> Cc: Eric Anholt <eric@anholt.net> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ray Jui <rjui@broadcom.com> Cc: Scott Branden <sbranden@broadcom.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Helge Deller <deller@gmx.de> Cc: Joachim Eastwood <manabian@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Tobias Klauser <tklauser@distanz.ch> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: "Maciej W. Rozycki" <macro@linux-mips.org> Cc: "Uwe Kleine-König" <kernel@pengutronix.de> Cc: Pat Gefre <pfg@sgi.com> Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Sylvain Lemieux <slemieux.tyco@gmail.com> Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Andy Gross <andy.gross@linaro.org> Cc: David Brown <david.brown@linaro.org> Cc: "Andreas Färber" <afaerber@suse.de> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Barry Song <baohua@kernel.org> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Timur Tabi <timur@tabi.org> Cc: Tony Prisk <linux@prisktech.co.nz> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Jiri Slaby <jslaby@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap: Fix EFR write on RTS deassertionLukas Wunner2017-10-231-1/+1
| | | | | | | | | | | | | Commit 348f9bb31c56 ("serial: omap: Fix RTS handling") sought to enable auto RTS upon manual RTS assertion and disable it on deassertion. However it seems the latter was done incorrectly, it clears all bits in the Extended Features Register *except* auto RTS. Fixes: 348f9bb31c56 ("serial: omap: Fix RTS handling") Cc: Peter Hurley <peter@hurleysoftware.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* omap_serial: Removing superfluous check on no interrupt pending.Martin Townsend2017-10-231-1/+1
| | | | | | | | | The do .. while loop checks for interrupt pending at the start of the loop and exits if there is none, it then checks again for this condition at the end of the loop. Signed-off-by: Martin Townsend <mtownsend1973@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap-serial: Use common rs485 device tree parsing functionSascha Hauer2017-09-181-12/+1
| | | | | | | | | We just got a common helper for parsing the rs485 specific device tree properties. Use it and drop the open coded parser. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap: Remove __init marking from early writeJeffy Chen2017-07-301-7/+6
| | | | | | | | | | | | | The earlycon would be alive outside the init code in these cases: 1/ we have keep_bootcon in cmdline. 2/ we don't have a real console to switch to. So remove the __init marking to avoid invalid memory access. Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap: suspend device on probe errorsJohan Hovold2017-04-111-1/+2
| | | | | | | | | | | | | | | | Make sure to actually suspend the device before returning after a failed (or deferred) probe. Note that autosuspend must be disabled before runtime pm is disabled in order to balance the usage count due to a negative autosuspend delay as well as to make the final put suspend the device synchronously. Fixes: 388bc2622680 ("omap-serial: Fix the error handling in the omap_serial probe") Cc: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap: fix runtime-pm handling on unbindJohan Hovold2017-04-111-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | An unbalanced and misplaced synchronous put was used to suspend the device on driver unbind, something which with a likewise misplaced pm_runtime_disable leads to external aborts when an open port is being removed. Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa024010 ... [<c046e760>] (serial_omap_set_mctrl) from [<c046a064>] (uart_update_mctrl+0x50/0x60) [<c046a064>] (uart_update_mctrl) from [<c046a400>] (uart_shutdown+0xbc/0x138) [<c046a400>] (uart_shutdown) from [<c046bd2c>] (uart_hangup+0x94/0x190) [<c046bd2c>] (uart_hangup) from [<c045b760>] (__tty_hangup+0x404/0x41c) [<c045b760>] (__tty_hangup) from [<c045b794>] (tty_vhangup+0x1c/0x20) [<c045b794>] (tty_vhangup) from [<c046ccc8>] (uart_remove_one_port+0xec/0x260) [<c046ccc8>] (uart_remove_one_port) from [<c046ef4c>] (serial_omap_remove+0x40/0x60) [<c046ef4c>] (serial_omap_remove) from [<c04845e8>] (platform_drv_remove+0x34/0x4c) Fix this up by resuming the device before deregistering the port and by suspending and disabling runtime pm only after the port has been removed. Also make sure to disable autosuspend before disabling runtime pm so that the usage count is balanced and device actually suspended before returning. Note that due to a negative autosuspend delay being set in probe, the unbalanced put would actually suspend the device on first driver unbind, while rebinding and again unbinding would result in a negative power.usage_count. Fixes: 7e9c8e7dbf3b ("serial: omap: make sure to suspend device before remove") Cc: Felipe Balbi <balbi@kernel.org> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: serial: omap: add UPF_BOOT_AUTOCONF flag for DT initSebastian Reichel2017-04-081-0/+3
| | | | | | | | | The UPF_BOOT_AUTOCONF flag is needed for proper flow control support. Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: serial: constify uart_ops structuresBhumika Goyal2017-01-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Declare uart_ops structures as const as they are only stored in the ops field of an uart_port structure. This field is of type const, so uart_ops structures having this property can be made const too. File size details before and after patching. First line of every .o file shows the file size before patching and second line shows the size after patching. text data bss dec hex filename 2977 456 64 3497 da9 drivers/tty/serial/amba-pl010.o 3169 272 64 3505 db1 drivers/tty/serial/amba-pl010.o 3109 456 0 3565 ded drivers/tty/serial/efm32-uart.o 3301 272 0 3573 df5 drivers/tty/serial/efm32-uart.o 10668 753 1 11422 2c9e drivers/tty/serial/icom.o 10860 561 1 11422 2c9e drivers/tty/serial/icom.o 23904 408 8 24320 5f00 drivers/tty/serial/ioc3_serial.o 24088 224 8 24320 5f00 drivers/tty/serial/ioc3_serial.o 10516 560 4 11080 2b48 drivers/tty/serial/ioc4_serial.o 10709 368 4 11081 2b49 drivers/tty/serial/ioc4_serial.o 7853 648 1216 9717 25f5 drivers/tty/serial/mpsc.o 8037 456 1216 9709 25ed drivers/tty/serial/mpsc.o 10248 456 0 10704 29d0 drivers/tty/serial/omap-serial.o 10440 272 0 10712 29d8 drivers/tty/serial/omap-serial.o 8122 532 1984 10638 298e drivers/tty/serial/pmac_zilog.o 8306 340 1984 10630 2986 drivers/tty/serial/pmac_zilog.o 3808 456 0 4264 10a8 drivers/tty/serial/pxa.o 4000 264 0 4264 10a8 drivers/tty/serial/pxa.o 21781 3864 0 25645 642d drivers/tty/serial/serial-tegra.o 22037 3608 0 25645 642d drivers/tty/serial/serial-tegra.o 2481 456 96 3033 bd9 drivers/tty/serial/sprd_serial.o 2673 272 96 3041 be1 drivers/tty/serial/sprd_serial.o 5534 300 512 6346 18ca drivers/tty/serial/vr41xx_siu.o 5630 204 512 6346 18ca drivers/tty/serial/vr41xx_siu.o 6730 1576 128 8434 20f2 drivers/tty/serial/vt8500_serial.o 6986 1320 128 8434 20f2 drivers/tty/serial/vt8500_serial.o Cross compiled for mips architecture. 3005 488 0 3493 da5 drivers/tty/serial/pnx8xxx_uart.o 3189 304 0 3493 da5 drivers/tty/serial/pnx8xxx_uart.o 4272 196 1056 5524 1594 drivers/tty/serial/dz.o 4368 100 1056 5524 1594 drivers/tty/serial/dz.o 6551 144 16 6711 1a37 drivers/tty/serial/ip22zilog.o 6647 48 16 6711 1a37 drivers/tty/serial/ip22zilog.o 9612 428 1520 11560 2d28 drivers/tty/serial/serial_txx9.o 9708 332 1520 11560 2d28 drivers/tty/serial/serial_txx9.o 4156 296 16 4468 1174 drivers/tty/serial/ar933x_uart.o 4252 200 16 4468 1174 drivers/tty/serial/ar933x_uart.o Cross compiled for arm archiecture. 11716 1780 44 13540 34e4 drivers/tty/serial/sirfsoc_uart.o 11808 1688 44 13540 34e4 drivers/tty/serial/sirfsoc_uart.o 13352 596 56 14004 36b4 drivers/tty/serial/amba-pl011.o 13444 504 56 14004 36b4 drivers/tty/serial/amba-pl011.o Cross compiled for sparc architecture. 4664 528 32 5224 1468 drivers/tty/serial/sunhv.o 4848 344 32 5224 1468 drivers/tty/serial/sunhv.o 8080 332 28 8440 20f8 drivers/tty/serial/sunzilog.o 8184 228 28 8440 20f8 drivers/tty/serial/sunzilog.o Cross compiled for ia64 architecture. 10226 549 472 11247 2bef drivers/tty/serial/sn_console.o 10414 365 472 11251 2bf3 drivers/tty/serial/sn_console.o The files drivers/tty/serial/zs.o, drivers/tty/serial/lpc32xx_hs.o and drivers/tty/serial/lantiq.o did not compile. Signed-off-by: Bhumika Goyal <bhumirks@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap: Add omapserial earlyconLokesh Vutla2017-01-191-0/+55
| | | | | | | | | | | | | Add DT earlycon for omap_serial driver. This boot console is included with CONFIG_SERIAL_EARLYCON=y, CONFIG_OF=y, CONFIG_SERIAL_OMAP=y, and CONFIG_OF_EARLY_FLATTREE=y. This boot console is enabled with the command line option "earlycon" (without "=<name>...") when the DT 'stdout-path' property matches a compatible uart. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge 4.5-rc4 into tty-nextGreg Kroah-Hartman2016-02-141-3/+7
|\ | | | | | | | | | | We want the fixes in here, and this resolves a merge error in tty_io.c Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * serial/omap: mark wait_for_xmitr as __maybe_unusedArnd Bergmann2016-02-061-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The wait_for_xmitr() function is only used if CONFIG_CONSOLE_POLL or CONFIG_SERIAL_OMAP_CONSOLE are set, but when both are disabled, the compiler warns about it being unused: drivers/tty/serial/omap-serial.c:1168:13: warning: 'wait_for_xmitr' defined but not used [-Wunused-func We could add more #ifdefs to work around it, but adding __maybe_unused seems nicer. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 2172076d2399 ("serial/omap-serial: Deinline wait_for_xmitr, save 165 bytes") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * serial: omap: Prevent DoS using unprivileged ioctl(TIOCSRS485)Peter Hurley2016-02-061-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The omap-serial driver emulates RS485 delays using software timers, but neglects to clamp the input values from the unprivileged ioctl(TIOCSRS485). Because the software implementation busy-waits, malicious userspace could stall the cpu for ~49 days. Clamp the input values to < 100ms. Fixes: 4a0ac0f55b18 ("OMAP: add RS485 support") Cc: <stable@vger.kernel.org> # 3.12+ Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | ARM: OMAP: serial: Rename DRIVER_NAMEJean Delvare2016-02-061-1/+1
|/ | | | | | | | | | | DRIVER_NAME is too generic to be used in a driver-specific platform data file. Use a name specific to the driver instead, to avoid collisions. Signed-off-by: Jean Delvare <jdelvare@suse.de> Acked-by: Tony Lindgren <tony@atomide.com> Cc: Jiri Slaby <jslaby@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial/omap-serial: Deinline wait_for_xmitr, save 165 bytesDenys Vlasenko2015-12-131-1/+1
| | | | | | | | | | This function compiles to 141 bytes of machine code. Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com> CC: Jiri Slaby <jslaby@suse.com> CC: linux-serial@vger.kernel.org Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap: remove warnings about unused functionsEzequiel Garcia2015-10-041-0/+2
| | | | | | | | | | | | They're used by only if CONFIG_PM is enabled, so enclose them with proper ifdefs. Removes these warnings: drivers/tty/serial/omap-serial.c:202:12: warning: 'serial_omap_get_context_loss_count' defined but not used [-Wunused-function] drivers/tty/serial/omap-serial.c:213:13: warning: 'serial_omap_enable_wakeup' defined but not used [-Wunused-function] Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar> Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap: Switch wake-up interrupt to generic wakeirqTony Lindgren2015-06-091-31/+4
| | | | | | | | We can now use generic wakeirq handling and remove the custom handling for the wake-up interrupts. Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
* serial: omap: Fix error handling in probeSemen Protsenko2015-05-081-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is pm_qos_add_request() being executed on serial_omap_probe(), which stores "&up->pm_qos_request" from omap-serial driver to "pm_qos_array[PM_QOS_CPU_DMA_LATENCY]->constraints". If serial_omap_probe() fails after pm_qos_add_request() (e.g. on uart_add_one_port() call), pm_qos_array still keeping pm_qos_request struct from omap-serial driver, which is not valid anymore (since driver failed). This leads further to kernel crash on pm_qos_update_target(), executing from some completely different driver. We were observing this while trying to run audio playback while having one of omap-serial driver instances failed on uart_add_one_port() call: Unable to handle kernel paging request at virtual address fffffffc Backtrace: (plist_add) from (pm_qos_update_target) (pm_qos_update_target) from (pm_qos_add_request) (pm_qos_add_request) from (snd_pcm_hw_params) (snd_pcm_hw_params) from (snd_pcm_common_ioctl1) (snd_pcm_common_ioctl1) from (snd_pcm_playback_ioctl1) (snd_pcm_playback_ioctl1) from (snd_pcm_playback_ioctl) (snd_pcm_playback_ioctl) from (do_vfs_ioctl) (do_vfs_ioctl) from (SyS_ioctl) (SyS_ioctl) from (ret_fast_syscall) This patch adds pm_qos_remove_request() on fail path in serial_omap_probe() in order to fix this issue. While at it, free the wakeup settings on fail path as well, just like it's done in serial_omap_remove(). Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty/serial: omap: fix !wakeirq messageDoug Kehn2015-03-261-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | When wakeirq is not used/enabled, "no wakeirq for uart0" is output for all TTY as the log message is generated before the port line is initialized. [ 0.802656] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.811700] omap_uart 44e09000.serial: no wakeirq for uart0 [ 0.812379] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 1.503622] console [ttyO0] enabled [ 1.509836] omap_uart 48022000.serial: no wakeirq for uart0 [ 1.516118] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89, base_baud = 3000000) is a OMAP UART1 [ 1.527711] omap_uart 48024000.serial: no wakeirq for uart0 [ 1.533881] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90, base_baud = 3000000) is a OMAP UART2 [ 1.545324] omap_uart 481a6000.serial: no wakeirq for uart0 [ 1.551410] 481a6000.serial: ttyO3 at MMIO 0x481a6000 (irq = 60, base_baud = 3000000) is a OMAP UART3 [ 1.562946] omap_uart 481a8000.serial: no wakeirq for uart0 [ 1.569036] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61, base_baud = 3000000) is a OMAP UART4 Fix by moving wakeirq initialization, check, and dev_info() call to after port line initialization and validation. Signed-off-by: Doug Kehn <rdkehn@yahoo.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap: Fix RTS handlingPeter Hurley2015-02-021-8/+14
| | | | | | | | | | | | The OMAP UART ignores MCR[1] (ie., RTS) when in autoRTS mode. This makes it impossible for either the serial core or userspace to manually flow control the sender. Disable autoRTS mode when RTS is lowered and restore the previous mode when RTS is raised. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: core: Rework hw-assisted flow control supportPeter Hurley2015-02-021-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | hw-assisted flow control support was added to the serial core in v3.8 with commits, dba05832cbe4f ("SERIAL: core: add hardware assisted h/w flow control support") 2cbacafd7af0f ("SERIAL: core: add hardware assisted s/w flow control support") 9aba8d5b01119 ("SERIAL: core: add throttle/unthrottle callbacks for hardware assisted flow control") Since then, additional requirements for serial core support have arisen. Specifically, 1. Separate tx and rx flow control settings for UARTs which only support tx flow control (ie., autoCTS). 2. Disable sw-assisted CTS flow control in autoCTS mode 3. Support for RTS flow control by serial core and userspace in autoRTS mode Distinguish mode from capability; introduce UPSTAT_AUTORTS, UPSTAT_AUTOCTS and UPSTAT_AUTOXOFF which, when set by the uart driver, enable serial core support for hw-assisted rx, hw-assisted tx and hw-assisted in-band/IXOFF rx flow control, respectively. [Note: hw-assisted in-band/IXON tx flow control does not require serial core support/intervention and can be enabled by the uart driver when required.] These modes must be set/reset in the driver's set_termios() method, based on termios settings, and thus can be safely queried in any context in which one of the port lock, port mutex or termios rwsem are held. Set these modes in the 2 in-tree drivers, omap-serial and 8250_omap, which currently use UPF_HARD_FLOW/UPF_SOFT_FLOW support. Retain UPF_HARD_FLOW and UPF_SOFT_FLOW as capabilities; re-define UPF_HARD_FLOW as both UPF_AUTO_RTS and UPF_AUTO_CTS to allow for distinct and separate rx and tx flow control capabilities. Disable sw-assisted CTS flow control when UPSTAT_AUTOCTS is enabled. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* trivial fixes for omap-serialPavel Machek2015-01-091-4/+4
| | | | | | | | | Trivial fixes for omap-serial. Signed-off-by: Pavel Machek <pavel@ucw.cz> index 18c30ca..f43ed2c 100644 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge tag 'pm+acpi-3.19-rc1-2' of ↵Linus Torvalds2014-12-181-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull more ACPI and power management updates from Rafael Wysocki: "These are regression fixes (leds-gpio, ACPI backlight driver, operating performance points library, ACPI device enumeration messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device PM), some cleanups in the operating performance points (OPP) framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of minor intel_pstate driver changes, a new MAINTAINERS entry for it and an ACPI fan driver change needed for better support of thermal management in user space. Specifics: - Fix a regression in leds-gpio introduced by a recent commit that inadvertently changed the name of one of the properties used by the driver (Fabio Estevam). - Fix a regression in the ACPI backlight driver introduced by a recent fix that missed one special case that had to be taken into account (Aaron Lu). - Drop the level of some new kernel messages from the ACPI core introduced by a recent commit to KERN_DEBUG which they should have used from the start and drop some other unuseful KERN_ERR messages printed by ACPI (Rafael J Wysocki). - Revert an incorrect commit modifying the cpupower tool (Prarit Bhargava). - Fix two regressions introduced by recent commits in the OPP library and clean up some existing minor issues in that code (Viresh Kumar). - Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the tree (or drop it where that can be done) in order to make it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf Hansson, Ludovic Desroches). There will be one more "CONFIG_PM_RUNTIME removal" batch after this one, because some new uses of it have been introduced during the current merge window, but that should be sufficient to finally get rid of it. - Make the ACPI EC driver more robust against race conditions related to GPE handler installation failures (Lv Zheng). - Prevent the ACPI device PM core code from attempting to disable GPEs that it has not enabled which confuses ACPICA and makes it report errors unnecessarily (Rafael J Wysocki). - Add a "force" command line switch to the intel_pstate driver to make it possible to override the blacklisting of some systems in that driver if needed (Ethan Zhao). - Improve intel_pstate code documentation and add a MAINTAINERS entry for it (Kristen Carlson Accardi). - Make the ACPI fan driver create cooling device interfaces witn names that reflect the IDs of the ACPI device objects they are associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B"). That's necessary for user space thermal management tools to be able to connect the fans with the parts of the system they are supposed to be cooling properly. From Srinivas Pandruvada" * tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits) MAINTAINERS: add entry for intel_pstate ACPI / video: update the skip case for acpi_video_device_in_dod() power / PM: Eliminate CONFIG_PM_RUNTIME NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM ACPI / EC: Fix unexpected ec_remove_handlers() invocations Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()" tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c PM: Remove the SET_PM_RUNTIME_PM_OPS() macro mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro PM / Kconfig: Replace PM_RUNTIME with PM in dependencies ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM ACPI / PM: Do not disable wakeup GPEs that have not been enabled ACPI / utils: Drop error messages from acpi_evaluate_reference() ...
| * tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PMRafael J. Wysocki2014-12-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks depending on CONFIG_PM_RUNTIME may now be changed to depend on CONFIG_PM. Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under drivers/tty/. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | tty: serial: omap_serial: line is unsigned, don't check < 0Sebastian Andrzej Siewior2014-11-251-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Dan Carpenter reported: |drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe() |warn: unsigned 'up.port.line' is never less than zero. |1025 if (up.port.line < 0) { Since of_alias_get_id() and pdev->id can get negative I check for the error via ret variable. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | tty/serial_core: Introduce lock mechanism for RS485Ricardo Ribalda Delgado2014-11-061-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Introduce an homogeneous lock system between setting and using the rs485 data of the uart_port. This patch should not be split into multiple ones in order to avoid leaving the tree in an unstable state. Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Reviewed-by: Alan Cox <alan@linux.intel.com> Suggested-by: Alan Cox <alan@linux.intel.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Jiri Slaby <jslaby@suse.cz> Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | serial/omap: Use the rs485 functions on serial_coreRicardo Ribalda Delgado2014-11-061-47/+22
| | | | | | | | | | | | | | | | | | | | | | In order to unify all the rs485 ioctl handling Use the implementation of TIOC[GS]RS485 ioctl handling on serial_core. Reviewed-by: Alan Cox <alan@linux.intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | tty: serial: omap: Increase max consoles and add check to prevent crashNishanth Menon2014-11-061-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Increase the maximum number of consoles possible to 10 since DRA7 now has the maximum number of consoles possible. without doing this, for example, enabling DRA7 UART10 results in internal data structures and console cannot match up and we endup with a crash as follows: [ 1.903503] omap_uart 48424000.serial: [UART-1]: failure [serial_omap_probe]: -22 [ 1.911437] omap_uart: probe of 48424000.serial failed with error -22 [ 1.920379] Unable to handle kernel NULL pointer dereference at virtual address 00000004 [ 1.928894] pgd = c0004000 [ 1.931732] [00000004] *pgd=00000000 [ 1.935485] Internal error: Oops: 5 [#1] SMP ARM [ 1.940338] Modules linked in: [ 1.943542] CPU: 1 PID: 12 Comm: kworker/1:0 Tainted: G W 3.18.0-rc1-00001-g8821bc4-dirty #6 [ 1.953521] task: ed8a2d00 ti: ed8a4000 task.ti: ed8a4000 [ 1.959197] PC is at process_one_work+0x38/0x4a4 [ 1.964050] LR is at 0x0 [ 1.966705] pc : [<c00548e0>] lr : [<00000000>] psr: 40000093 [ 1.966705] sp : ed8a5ea8 ip : ed8a5ec8 fp : eeb9abc0 [ 1.978759] r10: ed8a4000 r9 : 00000008 r8 : ed842458 [ 1.984252] r7 : 00000000 r6 : eeb9abc0 r5 : ed842440 r4 : edbf26a8 [ 1.991119] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : 00000000 [ 1.997985] Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel [ 2.005767] Control: 10c5387d Table: 8000406a DAC: 00000015 [ 2.011810] Process kworker/1:0 (pid: 12, stack limit = 0xed8a4248) [ 2.018371] Stack: (0xed8a5ea8 to 0xed8a6000) [ 2.022949] 5ea0: 00000001 00000000 60000093 c008346c 00000001 ed8a5ec8 [ 2.031555] 5ec0: c0054de4 eeb9abc0 ed8a4000 ed842458 00000008 ed8a4000 eeb9abc0 ed842440 [ 2.040161] 5ee0: eeb9abc0 eeb9abf0 ed8a4000 ed842458 00000008 ed8a4000 eeb9abc0 c0054ec4 [ 2.048767] 5f00: ed8a4000 eeb9ac4c a0000053 00000000 ed845bc0 ed842440 c0054d80 00000000 [ 2.057342] 5f20: 00000000 00000000 00000000 c005999c 00000001 00000000 c05eaa64 ed842440 [ 2.065948] 5f40: 00000000 00000000 dead4ead ffffffff ffffffff c097c680 00000000 00000000 [ 2.074554] 5f60: c078acd4 ed8a5f64 ed8a5f64 00000000 00000000 dead4ead ffffffff ffffffff [ 2.083160] 5f80: c097c680 00000000 00000000 c078acd4 ed8a5f90 ed8a5f90 600000d3 ed845bc0 [ 2.091766] 5fa0: c00598d4 00000000 00000000 c000e668 00000000 00000000 00000000 00000000 [ 2.100341] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 2.108947] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 90005148 11010482 [ 2.117553] [<c00548e0>] (process_one_work) from [<c0054ec4>] (worker_thread+0x144/0x498) [ 2.126159] [<c0054ec4>] (worker_thread) from [<c005999c>] (kthread+0xc8/0xe4) [ 2.133758] [<c005999c>] (kthread) from [<c000e668>] (ret_from_fork+0x14/0x2c) [ 2.141357] Code: e1a04001 e1a05000 e893000f e31e0004 (e5978004) [ 2.147766] ---[ end trace 5798e2803311b69f ]--- <snip> The final solution is to transition off to use 8250 driver and no dependency on console structures and move away from omap-serial driver, hence no major cleanups are done for this driver, so add a simple check to prevent future crashes in a similar manner in case of platform with additional ports. Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | tty: serial: omap: Remove probe error messageMarkus Pargmann2014-11-051-2/+0
|/ | | | | | | | | | | | | This error message is not necessary. The driver core code will print all probe error messages. It also resolves some error codes to proper error messages. For example -EPROBE_DEFER will only be printed as an info message. This patch removes the error message as the core prints the same information. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: omap-serial: pull out calculation from baud_is_mode16Frans Klaver2014-09-281-18/+24
| | | | | | | | | | | | To determine the correct divisor, we need to know the difference between the desired baud rate and the actual baud rate. The calculation for this difference is implemented twice within omap_serial_baud_is_mode16(). Pull out the calculation for easier maintenance. While at it, remove the CamelCasing from the variable names. Signed-off-by: Frans Klaver <frans.klaver@xsens.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: omap-serial: fix division by zeroFrans Klaver2014-09-281-2/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | If the chosen baud rate is large enough (e.g. 3.5 megabaud), the calculated n values in serial_omap_is_baud_mode16() may become 0. This causes a division by zero when calculating the difference between calculated and desired baud rates. To prevent this, cap the n13 and n16 values on 1. Division by zero in kernel. [<c00132e0>] (unwind_backtrace) from [<c00112ec>] (show_stack+0x10/0x14) [<c00112ec>] (show_stack) from [<c01ed7bc>] (Ldiv0+0x8/0x10) [<c01ed7bc>] (Ldiv0) from [<c023805c>] (serial_omap_baud_is_mode16+0x4c/0x68) [<c023805c>] (serial_omap_baud_is_mode16) from [<c02396b4>] (serial_omap_set_termios+0x90/0x8d8) [<c02396b4>] (serial_omap_set_termios) from [<c0230a0c>] (uart_change_speed+0xa4/0xa8) [<c0230a0c>] (uart_change_speed) from [<c0231798>] (uart_set_termios+0xa0/0x1fc) [<c0231798>] (uart_set_termios) from [<c022bb44>] (tty_set_termios+0x248/0x2c0) [<c022bb44>] (tty_set_termios) from [<c022c17c>] (set_termios+0x248/0x29c) [<c022c17c>] (set_termios) from [<c022c3e4>] (tty_mode_ioctl+0x1c8/0x4e8) [<c022c3e4>] (tty_mode_ioctl) from [<c0227e70>] (tty_ioctl+0xa94/0xb18) [<c0227e70>] (tty_ioctl) from [<c00cf45c>] (do_vfs_ioctl+0x4a0/0x560) [<c00cf45c>] (do_vfs_ioctl) from [<c00cf568>] (SyS_ioctl+0x4c/0x74) [<c00cf568>] (SyS_ioctl) from [<c000e480>] (ret_fast_syscall+0x0/0x30) Signed-off-by: Frans Klaver <frans.klaver@xsens.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: serial: omap: fix Sparse warningsFelipe Balbi2014-04-241-2/+2
| | | | | | | | | | | | | | | | | | | | | Fix the following Sparse warnings: drivers/tty/serial/omap-serial.c:1418:49: warning: incorrect \ type in argument 2 (different address spaces) drivers/tty/serial/omap-serial.c:1418:49: expected void const \ [noderef] <asn:1>*from drivers/tty/serial/omap-serial.c:1418:49: got struct serial_rs485 \ *<noident> drivers/tty/serial/omap-serial.c:1426:35: warning: incorrect \ type in argument 1 (different address spaces) drivers/tty/serial/omap-serial.c:1426:35: expected void [noderef] \ <asn:1>*to drivers/tty/serial/omap-serial.c:1426:35: got struct serial_rs485 \ *<noident> Reported-by: Nishanth Menon <nm@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: serial: omap: remove unneeded singlethread workqueueFelipe Balbi2014-04-241-3/+0
| | | | | | | it wasn't used by anything, just remove it. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: serial: omap: remove some dead codeFelipe Balbi2014-04-241-39/+0
| | | | | | | | nobody passes a DTR_gpio to this driver, so this code is not necessary. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: serial: omap: switch over to devm_ioremap_resourceFelipe Balbi2014-04-241-23/+9
| | | | | | | | | | just using helper function to remove some duplicated code a bit. While at that, also move allocation of struct uart_omap_port higher in the code so that we return much earlier in case of no memory. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: serial: omap: switch over to platform_get_resourceFelipe Balbi2014-04-241-7/+3
| | | | | | | this way we can remove one pointer declaration. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: serial: omap: cleanup variable declarationsFelipe Balbi2014-04-241-3/+6
| | | | | | | cleanup only, no functional changes. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: serial: omap: switch over to devm_request_gpioFelipe Balbi2014-04-241-2/+3
| | | | | | | | this will make sure gpio gets freed automatically when this device is destroyed. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: serial: add missing bracesFelipe Balbi2014-04-241-1/+4
| | | | | | | | per CodingStyle we should have those braces, no functional changes. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Revert "serial: omap: unlock the port lock"Felipe Balbi2014-04-241-4/+1
| | | | | | | | | | | | | | | | This reverts commit 0324a821029e1f54e7a7f8fed48693cfce42dc0e. That commit tried to fix a deadlock problem when using hci_ldisc, but it turns out the bug was in hci_ldsic all along where it was calling ->write() from within ->write_wakeup() callback. The problem is that ->write_wakeup() was called with port lock held and ->write() tried to grab the same port lock. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap: Fix missing pm_runtime_resume handling by simplifying codeTony Lindgren2014-04-161-12/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The lack of pm_runtime_resume handling for the device state leads into device wake-up interrupts not working after a while for runtime PM. Also, serial-omap is confused about the use of device_may_wakeup. The checks for device_may_wakeup should only be done for suspend and resume, not for pm_runtime_suspend and pm_runtime_resume. The wake-up events for PM runtime should always be enabled. The lack of pm_runtime_resume handling leads into device wake-up interrupts not working after a while for runtime PM. Rather than try to patch over the issue of adding complex tests to the pm_runtime_resume, let's fix the issues properly: 1. Make serial_omap_enable_wakeup deal with all internal PM state handling so we don't need to test for up->wakeups_enabled elsewhere. Later on once omap3 boots in device tree only mode we can also remove the up->wakeups_enabled flag and rely on the wake-up interrupt enable/disable state alone. 2. Do the device_may_wakeup checks in suspend and resume only, for runtime PM the wake-up events need to be always enabled. 3. Finally just call serial_omap_enable_wakeup and make sure we call it also in pm_runtime_resume. 4. Note that we also have to use disable_irq_nosync as serial_omap_irq calls pm_runtime_get_sync. Fixes: 2a0b965cfb6e (serial: omap: Add support for optional wake-up) Cc: stable@vger.kernel.org # v3.13+ Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap: free the wakeup settings in removeSanjay Singh Rawat2014-04-161-0/+1
| | | | | Signed-off-by: Sanjay Singh Rawat <sanjay.rawat@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty/serial: omap: empty the RX FIFO at the end of half-duplex TXDimitris Lampridis2014-03-171-0/+6
| | | | | | | | Provided that the SER_RS485_RX_DURING_TX flag is not set, empty the RX FIFO to prevent reading back the transmitted data. Signed-off-by: Dimitris Lampridis <dlampridis@logikonlabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty/serial: omap: fix RX interrupt enable/disable in half-duplex TXDimitris Lampridis2014-03-171-2/+3
| | | | | | | | | | | | | | | | Make sure that serial_omap_stop_rx() also disables RDI (Receiver Data Interrupt), otherwise the interrupt handler will call serial_omap_rdi() to read the new data, resulting in the transmission being echoed back. When the half-duplex transmission is complete, in order to reverse the effects of serial_omap_stop_rx(), we should re-enable: * the RX interrupts _without_ overwriting up->ier * the UART_LSR_DR bit of the up->port.read_status_mask Signed-off-by: Dimitris Lampridis <dlampridis@logikonlabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap: fix rs485 probe on defered pinctrlMichael Grzeschik2014-02-131-1/+4
| | | | | | | | | If the gpio is not yet available we better also defer the probing in the rs485 case. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: omap-serial: Move info message to probe functionMarkus Pargmann2014-02-131-3/+3
| | | | | | | | | | | | | | | | | | | | Currently the info message about a missing wakeirq for uart is printed every time the serial driver's startup function is called. This happens multiple times and not just once. This can cause lots of extra messages at boot time, slowing things down. It is caused by commit 2a0b965cfb6e (serial: omap: Add support for optional wake-up) which was applied for v3.13-rc1. This patch moves the infomessage to the probe function to display it only once. Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: stable <stable@vger.kernel.org> # 3.13 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-08 19:29:37 +0000