summaryrefslogtreecommitdiffstats
path: root/drivers/tty
Commit message (Collapse)AuthorAgeFilesLines
* vt/fbcon: deinitialize resources in visual_init() after failed memory allocationGrzegorz Halat2019-05-241-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After memory allocation failure vc_allocate() doesn't clean up data which has been initialized in visual_init(). In case of fbcon this leads to divide-by-0 in fbcon_init() on next open of the same tty. memory allocation in vc_allocate() may fail here: 1097: vc->vc_screenbuf = kzalloc(vc->vc_screenbuf_size, GFP_KERNEL); on next open() fbcon_init() skips vc_font.data initialization: 1088: if (!p->fontdata) { division by zero in fbcon_init() happens here: 1149: new_cols /= vc->vc_font.width; Additional check is needed in fbcon_deinit() to prevent usage of uninitialized vc_screenbuf: 1251: if (vc->vc_hi_font_mask && vc->vc_screenbuf) 1252: set_vc_hi_font(vc, false); Crash: #6 [ffffc90001eafa60] divide_error at ffffffff81a00be4 [exception RIP: fbcon_init+463] RIP: ffffffff814b860f RSP: ffffc90001eafb18 RFLAGS: 00010246 ... #7 [ffffc90001eafb60] visual_init at ffffffff8154c36e #8 [ffffc90001eafb80] vc_allocate at ffffffff8154f53c #9 [ffffc90001eafbc8] con_install at ffffffff8154f624 ... Signed-off-by: Grzegorz Halat <ghalat@redhat.com> Reviewed-by: Oleksandr Natalenko <oleksandr@redhat.com> Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: max310x: Fix external crystal register setupJoe Burmeister2019-05-211-1/+1
| | | | | | | | | | | | | | | | | | | | The datasheet states: Bit 4: ClockEnSet the ClockEn bit high to enable an external clocking (crystal or clock generator at XIN). Set the ClockEn bit to 0 to disable clocking Bit 1: CrystalEnSet the CrystalEn bit high to enable the crystal oscillator. When using an external clock source at XIN, CrystalEn must be set low. The bit 4, MAX310X_CLKSRC_EXTCLK_BIT, should be set and was not. This was required to make the MAX3107 with an external crystal on our board able to send or receive data. Signed-off-by: Joe Burmeister <joe.burmeister@devtank.co.uk> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: sh-sci: disable DMA for uart_consoleGeorge G. Davis2019-05-211-0/+7
| | | | | | | | | | | | | | | | | | As noted in commit 84b40e3b57ee ("serial: 8250: omap: Disable DMA for console UART"), UART console lines use low-level PIO only access functions which will conflict with use of the line when DMA is enabled, e.g. when the console line is also used for systemd messages. So disable DMA support for UART console lines. Reported-by: Michael Rodin <mrodin@de.adit-jv.com> Link: https://patchwork.kernel.org/patch/10929511/ Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org Signed-off-by: George G. Davis <george_davis@mentor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* serial: imx: remove log spamming error messageSascha Hauer2019-05-211-1/+0
| | | | | | | | | | | | | Each time the DMA engine signals a transaction error the driver prints a message at error level. Getting transaction errors is pretty much expected on baudrate mismatches and the correspoding error counters are increased in this case properly. Remove the error message which is possibly repeated at a very high rate which can lock up the whole system. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tty: serial: msm_serial: Fix XON/XOFFJorge Ramirez-Ortiz2019-05-211-1/+4
| | | | | | | | | | | | | | | | | | When the tty layer requests the uart to throttle, the current code executing in msm_serial will trigger "Bad mode in Error Handler" and generate an invalid stack frame in pstore before rebooting (that is if pstore is indeed configured: otherwise the user shall just notice a reboot with no further information dumped to the console). This patch replaces the PIO byte accessor with the word accessor already used in PIO mode. Fixes: 68252424a7c7 ("tty: serial: msm: Support big-endian CPUs") Cc: stable@vger.kernel.org Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge tag 'riscv-for-linus-5.2-mw2' of ↵Linus Torvalds2019-05-191-1/+0
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux Pull RISC-V updates from Palmer Dabbelt: "This contains an assortment of RISC-V related patches that I'd like to target for the 5.2 merge window. Most of the patches are cleanups, but there are a handful of user-visible changes: - The nosmp and nr_cpus command-line arguments are now supported, which work like normal. - The SBI console no longer installs itself as a preferred console, we rely on standard mechanisms (/chosen, command-line, hueristics) instead. - sfence_remove_sfence_vma{,_asid} now pass their arguments along to the SBI call. - Modules now support BUG(). - A missing sfence.vma during boot has been added. This bug only manifests during boot. - The arch/riscv support for SiFive's L2 cache controller has been merged, which should un-block the EDAC framework work. I've only tested this on QEMU again, as I didn't have time to get things running on the Unleashed. The latest master from this morning merges in cleanly and passes the tests as well" * tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux: (31 commits) riscv: fix locking violation in page fault handler RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs RISC-V: Add DT documentation for SiFive L2 Cache Controller RISC-V: Avoid using invalid intermediate translations riscv: Support BUG() in kernel module riscv: Add the support for c.ebreak check in is_valid_bugaddr() riscv: support trap-based WARN() riscv: fix sbi_remote_sfence_vma{,_asid}. riscv: move switch_mm to its own file riscv: move flush_icache_{all,mm} to cacheflush.c tty: Don't force RISCV SBI console as preferred console RISC-V: Access CSRs using CSR numbers RISC-V: Add interrupt related SCAUSE defines in asm/csr.h RISC-V: Use tabs to align macro values in asm/csr.h RISC-V: Fix minor checkpatch issues. RISC-V: Support nr_cpus command line option. RISC-V: Implement nosmp commandline option. RISC-V: Add RISC-V specific arch_match_cpu_phys_id riscv: vdso: drop unnecessary cc-ldoption riscv: call pm_power_off from machine_halt / machine_power_off ...
| * tty: Don't force RISCV SBI console as preferred consoleAnup Patel2019-05-161-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linux kernel will auto-disables all boot consoles whenever it gets a preferred real console. Currently on RISC-V systems, if we have a real console which is not RISCV SBI console then boot consoles (such as earlycon=sbi) are not auto-disabled when a real console (ttyS0 or ttySIF0) is available. This results in duplicate prints at boot-time after kernel starts using real console (i.e. ttyS0 or ttySIF0) if "earlycon=" kernel parameter was passed by bootloader. The reason for above issue is that RISCV SBI console always adds itself as preferred console which is causing other real consoles to be not used as preferred console. Ideally "console=" kernel parameter passed by bootloaders should be the one selecting a preferred real console. This patch fixes above issue by not forcing RISCV SBI console as preferred console. Fixes: afa6b1ccfad5 ("tty: New RISC-V SBI console driver") Cc: stable@vger.kernel.org Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
* | panic: avoid the extra noise dmesgFeng Tang2019-05-141-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When kernel panic happens, it will first print the panic call stack, then the ending msg like: [ 35.743249] ---[ end Kernel panic - not syncing: Fatal exception [ 35.749975] ------------[ cut here ]------------ The above message are very useful for debugging. But if system is configured to not reboot on panic, say the "panic_timeout" parameter equals 0, it will likely print out many noisy message like WARN() call stack for each and every CPU except the panic one, messages like below: WARNING: CPU: 1 PID: 280 at kernel/sched/core.c:1198 set_task_cpu+0x183/0x190 Call Trace: <IRQ> try_to_wake_up default_wake_function autoremove_wake_function __wake_up_common __wake_up_common_lock __wake_up wake_up_klogd_work_func irq_work_run_list irq_work_tick update_process_times tick_sched_timer __hrtimer_run_queues hrtimer_interrupt smp_apic_timer_interrupt apic_timer_interrupt For people working in console mode, the screen will first show the panic call stack, but immediately overridden by these noisy extra messages, which makes debugging much more difficult, as the original context gets lost on screen. Also these noisy messages will confuse some users, as I have seen many bug reporters posted the noisy message into bugzilla, instead of the real panic call stack and context. Adding a flag "suppress_printk" which gets set in panic() to avoid those noisy messages, without changing current kernel behavior that both panic blinking and sysrq magic key can work as is, suggested by Petr Mladek. To verify this, make sure kernel is not configured to reboot on panic and in console # echo c > /proc/sysrq-trigger to see if console only prints out the panic call stack. Link: http://lkml.kernel.org/r/1551430186-24169-1-git-send-email-feng.tang@intel.com Signed-off-by: Feng Tang <feng.tang@intel.com> Suggested-by: Petr Mladek <pmladek@suse.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kees Cook <keescook@chromium.org> Cc: Borislav Petkov <bp@suse.de> Cc: Andi Kleen <ak@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | Merge tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds2019-05-091-2/+2
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull dmaengine updates from Vinod Koul: - Updates to stm32 dma residue calculations - Interleave dma capability to axi-dmac and support for ZynqMP arch - Rework of channel assignment for rcar dma - Debugfs for pl330 driver - Support for Tegra186/Tegra194, refactoring for new chips and support for pause/resume - Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma, rcar-dmac, stm32-dma etc - dev_get_drvdata() updates on few drivers * tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (34 commits) dmaengine: tegra210-adma: restore channel status dmaengine: tegra210-dma: free dma controller in remove() dmaengine: tegra210-adma: add pause/resume support dmaengine: tegra210-adma: add support for Tegra186/Tegra194 Documentation: DT: Add compatibility binding for Tegra186 dmaengine: tegra210-adma: prepare for supporting newer Tegra chips dmaengine: at_xdmac: remove a stray bottom half unlock dmaengine: fsl-edma: Adjust indentation dmaengine: fsl-edma: Fix typo in Vybrid name dmaengine: stm32-dma: fix residue calculation in stm32-dma dmaengine: nbpfaxi: Use dev_get_drvdata() dmaengine: bcm-sba-raid: Use dev_get_drvdata() dmaengine: stm32-dma: Fix unsigned variable compared with zero dmaengine: stm32-dma: use platform_get_irq() dmaengine: rcar-dmac: Update copyright information dmaengine: imx-sdma: Only check ratio on parts that support 1:1 dmaengine: xgene-dma: fix spelling mistake "descripto" -> "descriptor" dmaengine: idma64: Move driver name to the header dmaengine: bcm2835: Drop duplicate capability setting. dmaengine: pl330: _stop: clear interrupt status ...
| * | dmaengine: idma64: Use actual device for DMA transfersAndy Shevchenko2019-03-211-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Intel IOMMU, when enabled, tries to find the domain of the device, assuming it's a PCI one, during DMA operations, such as mapping or unmapping. Since we are splitting the actual PCI device to couple of children via MFD framework (see drivers/mfd/intel-lpss.c for details), the DMA device appears to be a platform one, and thus not an actual one that performs DMA. In a such situation IOMMU can't find or allocate a proper domain for its operations. As a result, all DMA operations are failed. In order to fix this, supply parent of the platform device to the DMA engine framework and fix filter functions accordingly. We may rely on the fact that parent is a real PCI device, because no other configuration is present in the wild. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [for tty parts] Signed-off-by: Vinod Koul <vkoul@kernel.org>
* | | Merge tag 'tty-5.2-rc1' of ↵Linus Torvalds2019-05-0841-119/+2604
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial updates from Greg KH: "Here is the "big" set of tty/serial driver patches for 5.2-rc1. It's really pretty small, not much happening in this portion of the kernel at the moment. When the "highlight" is the movement of the documentation from .txt to .rst files, it's a good merge window. There's a number of small fixes and updates over the various serial drivers, and a new "tty null" driver for those embedded systems that like to make things even smaller and not break things. All of these have been in linux-next for a while with no reported issues" * tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (45 commits) tty: serial: add driver for the SiFive UART dt-bindings: serial: add documentation for the SiFive UART driver serial: uartps: Add support for cts-override dt-bindings: xilinx-uartps: Add support for cts-override serial: milbeaut_usio: Fix error handling in probe and remove tty: rocket: deprecate the rp_ioctl tty: rocket: Remove RCPK_GET_STRUCT ioctl tty: update obsolete termios comment tty: serial_core: fix error code returned by uart_register_driver() serial: 8250-mtk: modify baudrate setting serial: 8250-mtk: add follow control docs: serial: convert docs to ReST and rename to *.rst serial: 8250_exar: Adjust IOT2000 matching TTY: serial_core, add ->install serial: Fix using plain integer instead of Null pointer tty:serial_core: Spelling mistake tty: Add NULL TTY driver tty: vt: keyboard: Allow Unicode compose base char Revert "tty: fix NULL pointer issue when tty_port ops is not set" serial: Add Milbeaut serial control ...
| * | | tty: serial: add driver for the SiFive UARTPaul Walmsley2019-04-293-0/+1081
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a serial driver for the SiFive UART, found on SiFive FU540 devices (among others). The underlying serial IP block is relatively basic, and currently does not support serial break detection. Further information on the IP block can be found in the documentation and Chisel sources: https://static.dev.sifive.com/FU540-C000-v1.0.pdf https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/uart This driver was written in collaboration with Wesley Terpstra <wesley@sifive.com>. Tested on a SiFive HiFive Unleashed A00 board, using BBL and the open- source FSBL (using a DT file based on what's targeted for mainline). This revision incorporates changes based on comments by Julia Lawall <julia.lawall@lip6.fr>, Emil Renner Berthing <kernel@esmil.dk>, and Andreas Schwab <schwab@suse.de>. Thanks also to Andreas for testing the driver with his userspace and reporting a bug with the set_termios implementation. Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Palmer Dabbelt <palmer@sifive.com> Cc: Wesley Terpstra <wesley@sifive.com> Cc: linux-serial@vger.kernel.org Cc: linux-riscv@lists.infradead.org Cc: linux-kernel@vger.kernel.org Cc: Julia Lawall <julia.lawall@lip6.fr> Cc: Emil Renner Berthing <kernel@esmil.dk> Cc: Andreas Schwab <schwab@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | serial: uartps: Add support for cts-overrideShubhrajyoti Datta2019-04-291-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Having flow is configurable. Add support for the same by checking for cts-override. Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | serial: milbeaut_usio: Fix error handling in probe and removeWei Yongjun2019-04-291-8/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | devm_clk_get() is used so there is no reason to explicitly call clk_put() in probe or remove functions. Also remove duplicate assign for port->membase. Fixes: ba44dc043004 ("serial: Add Milbeaut serial control") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Tested-by: Sugaya Taichi <sugaya.taichi@socionext.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | tty: rocket: deprecate the rp_ioctlFuqian Huang2019-04-251-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The rp_ioctl is deprecated. Add dev_warn_ratelimited to warn the use of rp_ioctl. Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | tty: rocket: Remove RCPK_GET_STRUCT ioctlFuqian Huang2019-04-252-5/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the cmd is RCPK_GET_STRUCT, copy_to_user will copy info to user space. As info->port.ops is the address of a constant object rocket_port_ops (assigned in init_r_port), a kernel address leakage happens. Remove the RCPK_GET_STRUCT ioctl. Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | tty: update obsolete termios commentJohan Hovold2019-04-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Update an obsolete comment referring to the termios_locked structure which was removed over a decade ago by commit fe6e29fdb1a7 ("tty: simplify ktermios allocation"). While at it, fix the "Thus" typo. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | tty: serial_core: fix error code returned by uart_register_driver()Sergey Organov2019-04-251-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | uart_register_driver() returned -ENOMEM on any error, even when tty_register_driver() call returned another one, such as -EBUSY. Signed-off-by: Sergey Organov <sorganov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | serial: 8250-mtk: modify baudrate settingLong Cheng2019-04-251-0/+102
| | | | | | | | | | | | | | | | | | | | | | | | | | | | In termios function, add Fractional divider to adjust baudrate. Signed-off-by: Long Cheng <long.cheng@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | serial: 8250-mtk: add follow controlLong Cheng2019-04-251-23/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add SW and HW follow control function. Signed-off-by: Long Cheng <long.cheng@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | docs: serial: convert docs to ReST and rename to *.rstMauro Carvalho Chehab2019-04-252-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The converted files are focused at the Kernel internal API, so, this is a good candidate for the kernel API set of books. The conversion is actually: - add blank lines and identation in order to identify paragraphs; - fix tables markups; - add some lists markups; - mark literal blocks; - adjust title markups. At its new index.rst, let's add a :orphan: while this is not linked to the main index.rst file, in order to avoid build warnings. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | serial: 8250_exar: Adjust IOT2000 matchingSu Bao Cheng2019-04-251-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since there are more IOT2040 variants with identical hardware but different asset tags, the asset tag matching should be adjusted to support them. As only the IOT2040 variants have the Exar chip on board, matching on their board name is enough. In the future there will be no other devices with the "SIMATIC IOT2000" DMI board name but different hardware. Signed-off-by: Su Bao Cheng <baocheng.su@siemens.com> Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | TTY: serial_core, add ->installJiri Slaby2019-04-251-11/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We need to compute the uart state only on the first open. This is usually what is done in the ->install hook. serial_core used to do this in ->open on every open. So move it to ->install. As a side effect, it ensures the state is set properly in the window after tty_init_dev is called, but before uart_open. This fixes a bunch of races between tty_open and flush_to_ldisc we were dealing with recently. One of such bugs was attempted to fix in commit fedb5760648a (serial: fix race between flush_to_ldisc and tty_open), but it only took care of a couple of functions (uart_start and uart_unthrottle). I was able to reproduce the crash on a SLE system, but in uart_write_room which is also called from flush_to_ldisc via process_echoes. I was *unable* to reproduce the bug locally. It is due to having this patch in my queue since 2012! general protection fault: 0000 [#1] SMP KASAN PTI CPU: 1 PID: 5 Comm: kworker/u4:0 Tainted: G L 4.12.14-396-default #1 SLE15-SP1 (unreleased) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-0-ga698c89-prebuilt.qemu.org 04/01/2014 Workqueue: events_unbound flush_to_ldisc task: ffff8800427d8040 task.stack: ffff8800427f0000 RIP: 0010:uart_write_room+0xc4/0x590 RSP: 0018:ffff8800427f7088 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 000000000000002f RSI: 00000000000000ee RDI: ffff88003888bd90 RBP: ffffffffb9545850 R08: 0000000000000001 R09: 0000000000000400 R10: ffff8800427d825c R11: 000000000000006e R12: 1ffff100084fee12 R13: ffffc900004c5000 R14: ffff88003888bb28 R15: 0000000000000178 FS: 0000000000000000(0000) GS:ffff880043300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000561da0794148 CR3: 000000000ebf4000 CR4: 00000000000006e0 Call Trace: tty_write_room+0x6d/0xc0 __process_echoes+0x55/0x870 n_tty_receive_buf_common+0x105e/0x26d0 tty_ldisc_receive_buf+0xb7/0x1c0 tty_port_default_receive_buf+0x107/0x180 flush_to_ldisc+0x35d/0x5c0 ... 0 in rbx means tty->driver_data is NULL in uart_write_room. 0x178 is tried to be dereferenced (0x178 >> 3 is 0x2f in rdx) at uart_write_room+0xc4. 0x178 is exactly (struct uart_state *)NULL->refcount used in uart_port_lock from uart_write_room. So revert the upstream commit here as my local patch should fix the whole family. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Li RongQing <lirongqing@baidu.com> Cc: Wang Li <wangli39@baidu.com> Cc: Zhang Yu <zhangyu31@baidu.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | serial: Fix using plain integer instead of Null pointerSugaya Taichi2019-04-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix build warning that using plain integer as Null pointer. This is reported by kbuild test robot. Fixes: ba44dc043004 ("serial: Add Milbeaut serial control") Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | Merge 5.1-rc6 into tty-nextGreg Kroah-Hartman2019-04-213-4/+9
| |\ \ \ | | | |/ | | |/| | | | | | | | | | | | | We want the serial/tty fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | tty:serial_core: Spelling mistakeHariprasad Kelam2019-04-161-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | fix spelling mistake "overriden" -> "overridden" This fix resolves warning reported by checkpatch tool. Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | tty: Add NULL TTY driverVincent Whitchurch2019-04-163-0/+124
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If no console driver is enabled (or if a non-present driver is selected with something like console=null in an attempt to disable the console), opening /dev/console errors out, and init scripts and other userspace code that relies on the existence of a console will fail. Symlinking /dev/null to /dev/console does not solve the problem since /dev/null does not behave like a real TTY. To just provide a dummy console to userspace when no console driver is available or desired, add a ttynull driver which simply discards all writes. It can be chosen on the command line in the standard way, i.e. with console=ttynull. Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | tty: vt: keyboard: Allow Unicode compose base charReinis Danne2019-04-161-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pass Unicode character to k_unicode handler function to honor possible accent_table definition. With introduction of KDSKBDIACRUC ioctl, it has been possible to set compose characters (diacr, base and result) to any Unicode character (below 0xf000 code point) as defined in struct kbdiacruc. But it does not work with characters beyond Latin-1 as base, because they are printed early and not passed to any of the handler functions, thus breaking compose and dead keys. It affects keyboard layouts defining such characters on level 1 and relying on dead keys to access level 3 (e.g., lv-modern with some modifications for extra characters on level 3 for ē, ā and ī keys). Signed-off-by: Reinis Danne <rei4dan@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | Revert "tty: fix NULL pointer issue when tty_port ops is not set"Johan Hovold2019-04-161-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit f4e68d58cf2b20a581759bbc7228052534652673. TTY drivers using the tty-port abstraction all provide a pointer to a set of port operations, which specifically cannot be NULL (or we'd find out at first attempt to open a port). Revert the recent commit which added unnecessary NULL-checks and whose commit message indicated that it was fixing a real problem, which it did not. Note that even the two tty drivers for virtual devices currently providing an empty set of operations probably should be implementing at least some of the callbacks. Cc: Fabien Dessenne <fabien.dessenne@st.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | serial: Add Milbeaut serial controlSugaya Taichi2019-04-163-0/+648
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add Milbeaut serial control including earlycon and console. Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | tty/vt: avoid high order pages allocation on GIO_UNIMAP ioctlKonstantin Khorenko2019-04-161-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | GIO_UNIMAP can easily result in a high order allocation, seen 6th order allocation on radeondrmfb: fbcon: radeondrmfb (fb0) is primary device Console: switching to colour frame buffer device 160x64 radeon 0000:01:05.0: fb0: radeondrmfb frame buffer device WARNING: CPU: 0 PID: 78661 at mm/page_alloc.c:3532 __alloc_pages_nodemask+0x1b1/0x600 order 6 >= 3, gfp 0x40d0 The warning is generated by a debug patch. At the same time it's safe to use kvmalloc() for allocation in con_get_unimap(), so let's do the substitution. And do the same for con_set_unimap(). Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | tty: remove redundant 'default n' from Kconfig-sBartlomiej Zolnierkiewicz2019-04-163-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 'default n' is the default value for any bool or tristate Kconfig setting so there is no need to write it explicitly. Also since commit f467c5640c29 ("kconfig: only write '# CONFIG_FOO is not set' for visible symbols") the Kconfig behavior is the same regardless of 'default n' being present or not: ... One side effect of (and the main motivation for) this change is making the following two definitions behave exactly the same: config FOO bool config FOO bool default n With this change, neither of these will generate a '# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied). That might make it clearer to people that a bare 'default n' is redundant. ... Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | serial: sprd: Fix a copy-paste err in sprd_request_dma()YueHaibing2019-04-161-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | when dma_request_chan rx_dma fails, dev_err log should print rx_dma err log. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Reviewed-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | n_tty: check for negative and zero space return from tty_write_roomColin Ian King2019-04-161-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The return from tty_write_room could potentially be negative if a tty write_room driver returns an error number (not that any seem to do). Rather than just check for a zero return, also check for a -ve return. This avoids the unsigned nr being set to a large unsigned value on the assignment from variable space and can lead to overflowing the buffer buf. Better to be safe than assume all write_room implementations in tty drivers are going to do the right thing. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | tty: fix up a few remaining files without SPDX identifiersGreg Kroah-Hartman2019-04-047-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There were a few straggling files under drivers/tty/ that did not have any SPDX identifier either because they entered the tree recently, or they somehow missed the mass-tagging of commit b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license") This commit follows the same rule as b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license") where files without any specified license in them fall under GPL-2.0 as the correct license for the individual file. Add that identifier to these remaining files so that we don't have to guess at the license of them in the future. Cc: Jiri Slaby <jslaby@suse.com> Cc: "David S. Miller" <davem@davemloft.net> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | tty: add SPDX identifiers to Kconfig and MakefilesGreg Kroah-Hartman2019-04-049-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There were a few Kconfig and Makefiles under drivers/tty/ that were missing a SPDX identifier. Fix that up so that automated tools can properly classify all kernel source files. Cc: Jiri Slaby <jslaby@suse.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: Rob Herring <robh@kernel.org> Acked-by: David Sterba <dsterba@suse.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | Merge 5.1-rc3 into tty-nextGreg Kroah-Hartman2019-04-0110-51/+74
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | We want the tty/serial fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | Revert "tty: pty: Fix race condition between release_one_tty and pty_write"Greg Kroah-Hartman2019-03-292-10/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit b9ca5f8560af244489b4a1bc1ae88b341f24bc95 as 0-day shows it has a circular locking dependency. Fixes: b9ca5f8560af ("tty: pty: Fix race condition between release_one_tty and pty_write") Reported-by: kernel test robot <lkp@intel.com> Cc: Sahara <keun-o.park@darkmatter.ae> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | vt: use /dev/vcs (not /dev/vcs0) in commentJakub Wilk2019-03-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Both /dev/vcs and /dev/vcs0 were in use in the past, but these days /dev/vcs0 is mostly historical curiosity. * "/dev/vcs" is the name that has always been in the Linux allocated devices list. * "vcs" is the device name in sysfs since Linux v2.6.12. * MAKEDEV(1) in Debian used to create /dev/vcs0 only, but /dev/vcs was added in 1999: https://bugs.debian.org/45698 * MAKEDEV(1) in RedHat switched from /dev/vcs0 to /dev/vcs in 2000: * Fri Oct 20 2000 Nalin Dahyabhai <nalin@redhat.com> - change vcs0 to vcs (ditto for vcsa0) Signed-off-by: Jakub Wilk <jwilk@jwilk.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | tty: pty: Fix race condition between release_one_tty and pty_writeSahara2019-03-282-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Especially when a linked tty is used such as pty, the linked tty port's buf works have not been cancelled while master tty port's buf work has been cancelled. Since release_one_tty and flush_to_ldisc run in workqueue threads separately, when pty_cleanup happens and link tty port is freed, flush_to_ldisc tries to access freed port and port->itty, eventually it causes a panic. This patch utilizes the magic value with holding the tty_mutex to check if the tty->link is valid. Fixes: 2b022ab7542d ("pty: cancel pty slave port buf's work in tty_release") Signed-off-by: Sahara <keun-o.park@darkmatter.ae> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | tty: vt.c: Fix TIOCL_BLANKSCREEN console blanking if blankinterval == 0Yifeng Li2019-03-281-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Previously, in the userspace, it was possible to use the "setterm" command from util-linux to blank the VT console by default, using the following command. According to the man page, > The force option keeps the screen blank even if a key is pressed. It was implemented by calling TIOCL_BLANKSCREEN. case BLANKSCREEN: ioctlarg = TIOCL_BLANKSCREEN; if (ioctl(STDIN_FILENO, TIOCLINUX, &ioctlarg)) warn(_("cannot force blank")); break; However, after Linux 4.12, this command ceased to work anymore, which is unexpected. By inspecting the kernel source, it shows that the issue was triggered by the side-effect from commit a4199f5eb809 ("tty: Disable default console blanking interval"). The console blanking is implemented by function do_blank_screen() in vt.c: "blank_state" will be initialized to "blank_normal_wait" in con_init() if AND ONLY IF ("blankinterval" > 0). If "blankinterval" is 0, "blank_state" will be "blank_off" (== 0), and a call to do_blank_screen() will always abort, even if a forced blanking is required from the user by calling TIOCL_BLANKSCREEN, the console won't be blanked. This behavior is unexpected from a user's point-of-view, since it's not mentioned in any documentation. The setterm man page suggests it will always work, and the kernel comments in uapi/linux/tiocl.h says > /* keep screen blank even if a key is pressed */ > #define TIOCL_BLANKSCREEN 14 To fix it, we simply remove the "blank_state != blank_off" check, as pointed out by Nicolas Pitre, this check doesn't logically make sense and it's safe to remove. Suggested-by: Nicolas Pitre <nicolas.pitre@linaro.org> Fixes: a4199f5eb809 ("tty: Disable default console blanking interval") Signed-off-by: Yifeng Li <tomli@tomli.me> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | tty/vt: fix write/write race in ioctl(KDSKBSENT) handlerSergei Trofimovich2019-03-281-6/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The bug manifests as an attempt to access deallocated memory: BUG: unable to handle kernel paging request at ffff9c8735448000 #PF error: [PROT] [WRITE] PGD 288a05067 P4D 288a05067 PUD 288a07067 PMD 7f60c2063 PTE 80000007f5448161 Oops: 0003 [#1] PREEMPT SMP CPU: 6 PID: 388 Comm: loadkeys Tainted: G C 5.0.0-rc6-00153-g5ded5871030e #91 Hardware name: Gigabyte Technology Co., Ltd. To be filled by O.E.M./H77M-D3H, BIOS F12 11/14/2013 RIP: 0010:__memmove+0x81/0x1a0 Code: 4c 89 4f 10 4c 89 47 18 48 8d 7f 20 73 d4 48 83 c2 20 e9 a2 00 00 00 66 90 48 89 d1 4c 8b 5c 16 f8 4c 8d 54 17 f8 48 c1 e9 03 <f3> 48 a5 4d 89 1a e9 0c 01 00 00 0f 1f 40 00 48 89 d1 4c 8b 1e 49 RSP: 0018:ffffa1b9002d7d08 EFLAGS: 00010203 RAX: ffff9c873541af43 RBX: ffff9c873541af43 RCX: 00000c6f105cd6bf RDX: 0000637882e986b6 RSI: ffff9c8735447ffb RDI: ffff9c8735447ffb RBP: ffff9c8739cd3800 R08: ffff9c873b802f00 R09: 00000000fffff73b R10: ffffffffb82b35f1 R11: 00505b1b004d5b1b R12: 0000000000000000 R13: ffff9c873541af3d R14: 000000000000000b R15: 000000000000000c FS: 00007f450c390580(0000) GS:ffff9c873f180000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffff9c8735448000 CR3: 00000007e213c002 CR4: 00000000000606e0 Call Trace: vt_do_kdgkb_ioctl+0x34d/0x440 vt_ioctl+0xba3/0x1190 ? __bpf_prog_run32+0x39/0x60 ? mem_cgroup_commit_charge+0x7b/0x4e0 tty_ioctl+0x23f/0x920 ? preempt_count_sub+0x98/0xe0 ? __seccomp_filter+0x67/0x600 do_vfs_ioctl+0xa2/0x6a0 ? syscall_trace_enter+0x192/0x2d0 ksys_ioctl+0x3a/0x70 __x64_sys_ioctl+0x16/0x20 do_syscall_64+0x54/0xe0 entry_SYSCALL_64_after_hwframe+0x49/0xbe The bug manifests on systemd systems with multiple vtcon devices: # cat /sys/devices/virtual/vtconsole/vtcon0/name (S) dummy device # cat /sys/devices/virtual/vtconsole/vtcon1/name (M) frame buffer device There systemd runs 'loadkeys' tool in tapallel for each vtcon instance. This causes two parallel ioctl(KDSKBSENT) calls to race into adding the same entry into 'func_table' array at: drivers/tty/vt/keyboard.c:vt_do_kdgkb_ioctl() The function has no locking around writes to 'func_table'. The simplest reproducer is to have initrams with the following init on a 8-CPU machine x86_64: #!/bin/sh loadkeys -q windowkeys ru4 & loadkeys -q windowkeys ru4 & loadkeys -q windowkeys ru4 & loadkeys -q windowkeys ru4 & loadkeys -q windowkeys ru4 & loadkeys -q windowkeys ru4 & loadkeys -q windowkeys ru4 & loadkeys -q windowkeys ru4 & wait The change adds lock on write path only. Reads are still racy. CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org> CC: Jiri Slaby <jslaby@suse.com> Link: https://lkml.org/lkml/2019/2/17/256 Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | tty: ipwireless: fix missing checks for ioremapKangjie Lu2019-03-281-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipw->attr_memory and ipw->common_memory are assigned with the return value of ioremap. ioremap may fail, but no checks are enforced. The fix inserts the checks to avoid potential NULL pointer dereferences. Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | tty: fix read of tty->pgrp outside of ctrl_lockDavid Emett2019-03-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The intention was clearly to use the tty_pgrp local variable rather than re-read tty->pgrp outside of ctrl_lock, so do that. This bug was introduced by commit 2812d9e9fd94 ("tty: Combine SIGTTOU/SIGTTIN handling"). Signed-off-by: David Emett <dave@sp4m.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | drivers/tty/tty_jobctrl.c - fix non-kerneldoc commentValdis Klētnieks2019-03-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Building with W=1 reports (among other things): CC drivers/tty/tty_jobctrl.o drivers/tty/tty_jobctrl.c:317: warning: Cannot understand * on line 317 - I thought it was a doc line Fix up the non-kerneldoc comment. (other warnings to be cleaned up in separate patch) Signed-off-by Valdis Kletnieks <valdis.kletnieks@vt.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | tty/sysrq: Convert show_lock to raw_spinlock_tJulien Grall2019-03-281-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Systems which don't provide arch_trigger_cpumask_backtrace() will invoke showacpu() from a smp_call_function() function which is invoked with disabled interrupts even on -RT systems. The function acquires the show_lock lock which only purpose is to ensure that the CPUs don't print simultaneously. Otherwise the output would clash and it would be hard to tell the output from CPUx apart from CPUy. On -RT the spin_lock() can not be acquired from this context. A raw_spin_lock() is required. It will introduce the system's latency by performing the sysrq request and other CPUs will block on the lock until the request is done. This is okay because the user asked for a backtrace of all active CPUs and under "normal circumstances in production" this path should not be triggered. Signed-off-by: Julien Grall <julien.grall@arm.com> [bigeasy@linuxtronix.de: commit description] Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | serial: sc16is7xx: Drop of_match_ptr() useAndy Shevchenko2019-03-281-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is an ACPI method to enumerate such devices via specific ACPI ID and use of compatible strings. It will not work for the drivers which have no OF match ID table present. Reported-by: Georgii Staroselskii <georgii.staroselskii@emlid.com> Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | serial: sc16is7xx: Switch to use device_get_match_data()Andy Shevchenko2019-03-281-13/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Instead of open coded variants, switch to direct use of device_get_match_data(). Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | serial: sc16is7xx: Respect clock-frequency propertyAndy Shevchenko2019-03-281-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the property is provided and there are no other possibilities to detect UART clock frequency, use it as a fallback. Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | serial: sprd: Add DMA mode supportLanqing Liu2019-03-281-14/+426
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add DMA mode support for the Spreadtrum serial controller. Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com> Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-13 09:15:04 +0000