summaryrefslogtreecommitdiffstats
path: root/drivers/usb/dwc3
Commit message (Collapse)AuthorAgeFilesLines
* usb: dwc3: Properly handle processing of pending eventsElson Roy Serrao2023-08-041-1/+8
| | | | | | | | | | | | | | | | | | | If dwc3 is runtime suspended we defer processing the event buffer until resume, by setting the pending_events flag. Set this flag before triggering resume to avoid race with the runtime resume callback. While handling the pending events, in addition to checking the event buffer we also need to process it. Handle this by explicitly calling dwc3_thread_interrupt(). Also balance the runtime pm get() operation that triggered this processing. Cc: stable@vger.kernel.org Fixes: fc8bb91bc83e ("usb: dwc3: implement runtime PM") Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20230801192658.19275-1-quic_eserrao@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: pci: skip BYT GPIO lookup table for hardwired phyGratian Crisan2023-07-271-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware based on the Bay Trail / BYT SoCs require an external ULPI phy for USB device-mode. The phy chip usually has its 'reset' and 'chip select' lines connected to GPIOs described by ACPI fwnodes in the DSDT table. Because of hardware with missing ACPI resources for the 'reset' and 'chip select' GPIOs commit 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources") introduced a fallback gpiod_lookup_table with hard-coded mappings for Bay Trail devices. However there are existing Bay Trail based devices, like the National Instruments cRIO-903x series, where the phy chip has its 'reset' and 'chip-select' lines always asserted in hardware via resistor pull-ups. On this hardware the phy chip is always enabled and the ACPI dsdt table is missing information not only for the 'chip-select' and 'reset' lines but also for the BYT GPIO controller itself "INT33FC". With the introduction of the gpiod_lookup_table initializing the USB device-mode on these hardware now errors out. The error comes from the gpiod_get_optional() calls in dwc3_pci_quirks() which will now return an -ENOENT error due to the missing ACPI entry for the INT33FC gpio controller used in the aforementioned table. This hardware used to work before because gpiod_get_optional() will return NULL instead of -ENOENT if no GPIO has been assigned to the requested function. The dwc3_pci_quirks() code for setting the 'cs' and 'reset' GPIOs was then skipped (due to the NULL return). This is the correct behavior in cases where the phy chip is hardwired and there are no GPIOs to control. Since the gpiod_lookup_table relies on the presence of INT33FC fwnode in ACPI tables only add the table if we know the entry for the INT33FC gpio controller is present. This allows Bay Trail based devices with hardwired dwc3 ULPI phys to continue working. Fixes: 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources") Cc: stable <stable@kernel.org> Signed-off-by: Gratian Crisan <gratian.crisan@ni.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20230726184555.218091-2-gratian.crisan@ni.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Revert "usb: dwc3: core: Enable AutoRetry feature in the controller"Jakub Vanek2023-07-252-19/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit b138e23d3dff90c0494925b4c1874227b81bddf7. AutoRetry has been found to sometimes cause controller freezes when communicating with buggy USB devices. This controller feature allows the controller in host mode to send non-terminating/burst retry ACKs instead of terminating retry ACKs to devices when a transaction error (CRC error or overflow) occurs. Unfortunately, if the USB device continues to respond with a CRC error, the controller will not complete endpoint-related commands while it keeps trying to auto-retry. [3] The xHCI driver will notice this once it tries to abort the transfer using a Stop Endpoint command and does not receive a completion in time. [1] This situation is reported to dmesg: [sda] tag#29 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN [sda] tag#29 CDB: opcode=0x28 28 00 00 69 42 80 00 00 48 00 xhci-hcd: xHCI host not responding to stop endpoint command xhci-hcd: xHCI host controller not responding, assume dead xhci-hcd: HC died; cleaning up Some users observed this problem on an Odroid HC2 with the JMS578 USB3-to-SATA bridge. The issue can be triggered by starting a read-heavy workload on an attached SSD. After a while, the host controller would die and the SSD would disappear from the system. [1] Further analysis by Synopsys determined that controller revisions other than the one in Odroid HC2 are also affected by this. The recommended solution was to disable AutoRetry altogether. This change does not have a noticeable performance impact. [2] Revert the enablement commit. This will keep the AutoRetry bit in the default state configured during SoC design [2]. Fixes: b138e23d3dff ("usb: dwc3: core: Enable AutoRetry feature in the controller") Link: https://lore.kernel.org/r/a21f34c04632d250cd0a78c7c6f4a1c9c7a43142.camel@gmail.com/ [1] Link: https://lore.kernel.org/r/20230711214834.kyr6ulync32d4ktk@synopsys.com/ [2] Link: https://lore.kernel.org/r/20230712225518.2smu7wse6djc7l5o@synopsys.com/ [3] Cc: stable@vger.kernel.org Cc: Mauro Ribeiro <mauro.ribeiro@hardkernel.com> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Jakub Vanek <linuxtardis@gmail.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230714122419.27741-1-linuxtardis@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: don't reset device side if dwc3 was configured as host-onlyJisheng Zhang2023-07-251-2/+2
| | | | | | | | | | | | | | | | | Commit c4a5153e87fd ("usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode") replaces check for HOST only dr_mode with current_dr_role. But during booting, the current_dr_role isn't initialized, thus the device side reset is always issued even if dwc3 was configured as host-only. What's more, on some platforms with host only dwc3, aways issuing device side reset by accessing device register block can cause kernel panic. Fixes: c4a5153e87fd ("usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode") Cc: stable <stable@kernel.org> Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230627162018.739-1-jszhang@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge tag 'usb-6.5-rc1' of ↵Linus Torvalds2023-07-0314-76/+76
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB / Thunderbolt driver updates from Greg KH: "Here is the big set of USB and Thunderbolt driver updates for 6.5-rc1. Included in here are: - Lots of USB4/Thunderbolt additions and updates for new hardware types and fixes as people are starting to get access to the hardware in the wild - new gadget controller driver, cdns2, added - new typec drivers added - xhci driver updates - typec driver updates - usbip driver fixes - usb-serial driver updates and fixes - lots of smaller USB driver updates All of these have been in linux-next for a while with no reported problems" * tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits) usb: host: xhci-plat: Set XHCI_STATE_REMOVING before resuming XHCI HC usb: host: xhci: Do not re-initialize the XHCI HC if being removed usb: typec: nb7vpq904m: fix CONFIG_DRM dependency usbip: usbip_host: Replace strlcpy with strscpy usb: dwc3: gadget: Propagate core init errors to UDC during pullup USB: serial: option: add LARA-R6 01B PIDs usb: ulpi: Make container_of() no-op in to_ulpi_dev() usb: gadget: legacy: fix error return code in gfs_bind usb: typec: fsa4480: add support for Audio Accessory Mode usb: typec: fsa4480: rework mux & switch setup to handle more states usb: typec: ucsi: call typec_set_mode on non-altmode partner change USB: gadget: f_hid: make hidg_class a static const structure USB: gadget: f_printer: make usb_gadget_class a static const structure USB: mon: make mon_bin_class a static const structure USB: gadget: udc: core: make udc_class a static const structure USB: roles: make role_class a static const structure dt-bindings: usb: dwc3: Add interrupt-names property support for wakeup interrupt dt-bindings: usb: Add StarFive JH7110 USB controller dt-bindings: usb: dwc3: Add IPQ9574 compatible usb: cdns2: Fix spelling mistake in a trace message "Wakupe" -> "Wakeup" ...
| * usb: dwc3: gadget: Propagate core init errors to UDC during pullupKrishna Kurapati2023-06-231-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In scenarios where pullup relies on resume (get sync) to initialize the controller and set the run stop bit, then core_init is followed by gadget_resume which will eventually set run stop bit. But in cases where the core_init fails, the return value is not sent back to udc appropriately. So according to UDC the controller has started but in reality we never set the run stop bit. On systems like Android, there are uevents sent to HAL depending on whether the configfs_bind / configfs_disconnect were invoked. In the above mentioned scnenario, if the core init fails, the run stop won't be set and the cable plug-out won't result in generation of any disconnect event and userspace would never get any uevent regarding cable plug out and we never call pullup(0) again. Furthermore none of the next Plug-In/Plug-Out's would be known to configfs. Return back the appropriate result to UDC to let the userspace/ configfs know that the pullup failed so they can take appropriate action. Fixes: 77adb8bdf422 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded") Cc: stable <stable@kernel.org> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Message-ID: <20230618120949.14868-1-quic_kriskura@quicinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * usb: dwc3-meson-g12a: Fix an error handling path in dwc3_meson_g12a_probe()Christophe JAILLET2023-06-131-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | If dwc3_meson_g12a_otg_init() fails, resources allocated by the previous of_platform_populate() call should be released, as already done in the error handling path. Fixes: 1e355f21d3fb ("usb: dwc3: Add Amlogic A1 DWC3 glue") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Message-ID: <9d28466de1808ccc756b4cc25fc72c482d133d13.1686403934.git.christophe.jaillet@wanadoo.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * usb: dwc3: qcom: use dev_err_probe() where appropriateAndrew Halaney2023-06-131-11/+9
| | | | | | | | | | | | | | | | | | Update to using dev_err_probe() throughout to reduce spam and log useful information in devices_deferred. Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Message-ID: <20230605193625.63187-1-ahalaney@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * usb: dwc3: qcom: Fix an error handling path in dwc3_qcom_probe()Christophe JAILLET2023-06-131-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | If dwc3_qcom_create_urs_usb_platdev() fails, some resources still need to be released, as already done in the other error handling path of the probe. Fixes: c25c210f590e ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Message-ID: <b69fa8dd68d816e7d24c88d3eda776ceb28c5dc5.1685890571.git.christophe.jaillet@wanadoo.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()Christophe JAILLET2023-06-131-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the probe, some resources are allocated with dwc3_qcom_of_register_core() or dwc3_qcom_acpi_register_core(). The corresponding resources are already coorectly freed in the error handling path of the probe, but not in the remove function. Fix it. Fixes: 2bc02355f8ba ("usb: dwc3: qcom: Add support for booting with ACPI") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Message-ID: <c0215a84cdf18fb3514c81842783ec53cf149deb.1685891059.git.christophe.jaillet@wanadoo.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * usb: dwc3: qcom: Fix potential memory leakVladislav Efanov2023-05-291-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Function dwc3_qcom_probe() allocates memory for resource structure which is pointed by parent_res pointer. This memory is not freed. This leads to memory leak. Use stack memory to prevent memory leak. Found by Linux Verification Center (linuxtesting.org) with SVACE. Fixes: 2bc02355f8ba ("usb: dwc3: qcom: Add support for booting with ACPI") Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru> Acked-by: Shawn Guo <shawn.guo@linaro.org> Link: https://lore.kernel.org/r/20230517172518.442591-1-VEfanov@ispras.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: fix up merge of 6.4-rc4 into usb-nextRoger Quadros2023-05-281-18/+8
| | | | | | | | | | | | | | | | | | The merge of 6.4-rc4 got the changes in drivers/usb/dwc3/gadget.c completely incorrect, so fix it up properly. Link: https://lore.kernel.org/r/f604f836-7858-6140-4ec1-9ba95cba6991@kernel.org Fixes: 7e530d32a365 ("Merge 6.4-rc4 into usb-next") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * Merge 6.4-rc4 into usb-nextGreg Kroah-Hartman2023-05-284-21/+154
| |\ | | | | | | | | | | | | | | | | | | | | | We need the USB fixes in here and this resolves merge conflicts in: drivers/usb/dwc3/gadget.c drivers/usb/gadget/udc/core.c Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3-xilinx: Convert to platform remove callback returning voidUwe Kleine-König2023-05-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230517230239.187727-23-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3-st: Convert to platform remove callback returning voidUwe Kleine-König2023-05-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230517230239.187727-22-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3-qcom: Convert to platform remove callback returning voidUwe Kleine-König2023-05-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230517230239.187727-21-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3-omap: Convert to platform remove callback returning voidUwe Kleine-König2023-05-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230517230239.187727-20-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3-of-simple: Convert to platform remove callback returning voidUwe Kleine-König2023-05-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230517230239.187727-19-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3-meson-g12a: Convert to platform remove callback returning voidUwe Kleine-König2023-05-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230517230239.187727-18-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3-keystone: Convert to platform remove callback returning voidUwe Kleine-König2023-05-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230517230239.187727-17-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3-imx8mp: Convert to platform remove callback returning voidUwe Kleine-König2023-05-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230517230239.187727-16-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3-exynos: Convert to platform remove callback returning voidUwe Kleine-König2023-05-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230517230239.187727-15-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3-am62: Convert to platform remove callback returning voidUwe Kleine-König2023-05-281-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230517230239.187727-14-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: core: Convert to platform remove callback returning voidUwe Kleine-König2023-05-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230517230239.187727-13-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3-meson-g12a: support OTG switch for all IP versionsDmitry Rokosov2023-05-131-13/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | From now, the Amlogic A1 USB controller is capable of switching between host and gadget modes based on the status of the OTG_ID signal or via manual USB role change. Previously, only the Amlogic A1 IP version did not use OTG support for host only mode, but this is no longer applicable. Therefore, the 'otg_switch_supported' option can now be removed as it is no longer required. Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20230511210455.6634-4-ddrokosov@sberdevices.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3: gadget: Bail out in pullup if soft reset timeout happensKrishna Kurapati2023-05-131-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the core soft reset timeout happens, avoid setting up event buffers and starting gadget as the writes to these registers may not reflect when in reset and setting the run stop bit can lead the controller to access wrong event buffer address resulting in a crash. Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230510075252.31023-2-quic_kriskura@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3: Add error logs for unknown endpoint eventsRoy Luo2023-05-132-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In cases where the controller somehow fails to write to event buffer memory (e.g. due to incorrect MMU config), the driver would receive all-zero dwc3 events. However, the abnormal event is silently dropped as a regular ep0out event. Add error logs when an unknown endpoint event is received to highlight the anomaly. Signed-off-by: Roy Luo <royluo@google.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230504000129.728316-1-royluo@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: dwc3: core: add support for realtek SoCs custom's global register start ↵Stanley Chang2023-05-132-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | address The Realtek RTD SoCs were designed with the global register address offset at 0x8100. The default address offset is constant at DWC3_GLOBALS_REGS_START (0xc100). Therefore, add a check if the compatible name of the parent is realtek,rtd-dwc3, then global register start address will remap to 0x8100. Signed-off-by: Stanley Chang <stanley_chang@realtek.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230505025104.18321-1-stanley_chang@realtek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | USB: dwc3: fix use-after-free on core driver unbindJohan Hovold2023-06-131-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some dwc3 glue drivers are currently accessing the driver data of the child core device directly, which is clearly a bad idea as the child may not have probed yet or may have been unbound from its driver. As a workaround until the glue drivers have been fixed, clear the driver data pointer before allowing the glue parent device to runtime suspend to prevent its driver from accessing data that has been freed during unbind. Fixes: 6dd2565989b4 ("usb: dwc3: add imx8mp dwc3 glue layer driver") Fixes: 6895ea55c385 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend") Cc: stable@vger.kernel.org # 5.12 Cc: Li Jun <jun.li@nxp.com> Cc: Sandeep Maheswaram <quic_c_sanm@quicinc.com> Cc: Krishna Kurapati <quic_kriskura@quicinc.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Message-ID: <20230607100540.31045-3-johan+linaro@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | USB: dwc3: qcom: fix NULL-deref on suspendJohan Hovold2023-06-131-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Qualcomm dwc3 glue driver is currently accessing the driver data of the child core device during suspend and on wakeup interrupts. This is clearly a bad idea as the child may not have probed yet or could have been unbound from its driver. The first such layering violation was part of the initial version of the driver, but this was later made worse when the hack that accesses the driver data of the grand child xhci device to configure the wakeup interrupts was added. Fixing this properly is not that easily done, so add a sanity check to make sure that the child driver data is non-NULL before dereferencing it for now. Note that this relies on subtleties like the fact that driver core is making sure that the parent is not suspended while the child is probing. Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/all/20230325165217.31069-4-manivannan.sadhasivam@linaro.org/ Fixes: d9152161b4bf ("usb: dwc3: Add Qualcomm DWC3 glue layer driver") Fixes: 6895ea55c385 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend") Cc: stable@vger.kernel.org # 3.18: a872ab303d5d: "usb: dwc3: qcom: fix use-after-free on runtime-PM wakeup" Cc: Sandeep Maheswaram <quic_c_sanm@quicinc.com> Cc: Krishna Kurapati <quic_kriskura@quicinc.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Message-ID: <20230607100540.31045-2-johan+linaro@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | usb: dwc3: gadget: Reset num TRBs before giving back the requestElson Roy Serrao2023-06-131-0/+1
| |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Consider a scenario where cable disconnect happens when there is an active usb reqest queued to the UDC. As part of the disconnect we would issue an end transfer with no interrupt-on-completion before giving back this request. Since we are giving back the request without skipping TRBs the num_trbs field of dwc3_request still holds the stale value previously used. Function drivers re-use same request for a given bind-unbind session and hence their dwc3_request context gets preserved across cable disconnect/connect. When such a request gets re-queued after cable connect, we would increase the num_trbs field on top of the previous stale value thus incorrectly representing the number of TRBs used. Fix this by resetting num_trbs field before giving back the request. Fixes: 09fe1f8d7e2f ("usb: dwc3: gadget: track number of TRBs per request") Cc: stable <stable@kernel.org> Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Message-ID: <1685654850-8468-1-git-send-email-quic_eserrao@quicinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: dwc3: fix a test for error in dwc3_core_init()Dan Carpenter2023-05-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | This was refactored recently and the "ret = " was accidentally deleted so the errors aren't checked. Fixes: 1d72fab47656 ("USB: dwc3: refactor phy handling") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/d0c5a04f-deee-4ebe-9b0b-dc5492564519@kili.mountain Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: dwc3: debugfs: Resume dwc3 before accessing registersUdipto Goswami2023-05-131-0/+109
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the dwc3 device is runtime suspended, various required clocks are in disabled state and it is not guaranteed that access to any registers would work. Depending on the SoC glue, a register read could be as benign as returning 0 or be fatal enough to hang the system. In order to prevent such scenarios of fatal errors, make sure to resume dwc3 then allow the function to proceed. Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Cc: stable@vger.kernel.org #3.2: 30332eeefec8: debugfs: regset32: Add Runtime PM support Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Tested-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230509144836.6803-1-quic_ugoswami@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: dwc3: fix gadget mode suspend interrupt handler issueLinyu Yuan2023-05-132-1/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When work in gadget mode, currently driver doesn't update software level link_state correctly as link state change event is not enabled for most devices, in function dwc3_gadget_suspend_interrupt(), it will only pass suspend event to UDC core when software level link state changes, so when interrupt generated in sequences of suspend -> reset -> conndone -> suspend, link state is not updated during reset and conndone, so second suspend interrupt event will not pass to UDC core. Remove link_state compare in dwc3_gadget_suspend_interrupt() and add a suspended flag to replace the compare function. Fixes: 799e9dc82968 ("usb: dwc3: gadget: conditionally disable Link State change events") Cc: stable <stable@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com> Link: https://lore.kernel.org/r/20230512004524.31950-1-quic_linyyuan@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: dwc3: gadget: Improve dwc3_gadget_suspend() and dwc3_gadget_resume()Roger Quadros2023-05-131-33/+34
|/ | | | | | | | | | | | | | | | | | | Prevent -ETIMEDOUT error on .suspend(). e.g. If gadget driver is loaded and we are connected to a USB host, all transfers must be stopped before stopping the controller else we will not get a clean stop i.e. dwc3_gadget_run_stop() will take several seconds to complete and will return -ETIMEDOUT. Handle error cases properly in dwc3_gadget_suspend(). Simplify dwc3_gadget_resume() by using the introduced helper function. Fixes: 9f8a67b65a49 ("usb: dwc3: gadget: fix gadget suspend/resume") Cc: stable@vger.kernel.org Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Roger Quadros <rogerq@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230503110048.30617-1-rogerq@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: gadget: Refactor EP0 forced stall/restart into a separate APIWesley Cheng2023-04-211-32/+21
| | | | | | | | | | | Several sequences utilize the same routine for forcing the control endpoint back into the SETUP phase. This is required, because those operations need to ensure that EP0 is back in the default state. Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com> Link: https://lore.kernel.org/r/20230420212759.29429-3-quic_wcheng@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: gadget: Execute gadget stop after halting the controllerWesley Cheng2023-04-211-2/+13
| | | | | | | | | | | | | | Do not call gadget stop until the poll for controller halt is completed. DEVTEN is cleared as part of gadget stop, so the intention to allow ep0 events to continue while waiting for controller halt is not happening. Fixes: c96683798e27 ("usb: dwc3: ep0: Don't prepare beyond Setup stage") Cc: stable@vger.kernel.org Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com> Link: https://lore.kernel.org/r/20230420212759.29429-2-quic_wcheng@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: gadget: Stall and restart EP0 if host is unresponsiveWesley Cheng2023-04-201-17/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It was observed that there are hosts that may complete pending SETUP transactions before the stop active transfers and controller halt occurs, leading to lingering endxfer commands on DEPs on subsequent pullup/gadget start iterations. dwc3_gadget_ep_disable name=ep8in flags=0x3009 direction=1 dwc3_gadget_ep_disable name=ep4in flags=1 direction=1 dwc3_gadget_ep_disable name=ep3out flags=1 direction=0 usb_gadget_disconnect deactivated=0 connected=0 ret=0 The sequence shows that the USB gadget disconnect (dwc3_gadget_pullup(0)) routine completed successfully, allowing for the USB gadget to proceed with a USB gadget connect. However, if this occurs the system runs into an issue where: BUG: spinlock already unlocked on CPU spin_bug+0x0 dwc3_remove_requests+0x278 dwc3_ep0_out_start+0xb0 __dwc3_gadget_start+0x25c This is due to the pending endxfers, leading to gadget start (w/o lock held) to execute the remove requests, which will unlock the dwc3 spinlock as part of giveback. To mitigate this, resolve the pending endxfers on the pullup disable path by re-locating the SETUP phase check after stop active transfers, since that is where the DWC3_EP_DELAY_STOP is potentially set. This also allows for handling of a host that may be unresponsive by using the completion timeout to trigger the stall and restart for EP0. Fixes: c96683798e27 ("usb: dwc3: ep0: Don't prepare beyond Setup stage") Cc: stable@vger.kernel.org Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com> Link: https://lore.kernel.org/r/20230413195742.11821-2-quic_wcheng@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: core: add support for disabling High-speed park modeStanley Chang2023-04-202-0/+9
| | | | | | | | | | | | | | | | | | | | | | | Setting the PARKMODE_DISABLE_HS bit in the DWC3_USB3_GUCTL1. When this bit is set to '1' all HS bus instances in park mode are disabled For some USB wifi devices, if enable this feature it will reduce the performance. Therefore, add an option for disabling HS park mode by device-tree. In Synopsys's dwc3 data book: In a few high speed devices when an IN request is sent within 900ns of the ACK of the previous packet, these devices send a NAK. When connected to these devices, if required, the software can disable the park mode if you see performance drop in your system. When park mode is disabled, pipelining of multiple packet is disabled and instead one packet at a time is requested by the scheduler. This allows up to 12 NAKs in a micro-frame and improves performance of these slow devices. Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Stanley Chang <stanley_chang@realtek.com> Link: https://lore.kernel.org/r/20230419020044.15475-1-stanley_chang@realtek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: dwc3: clean up probe declarationsJohan Hovold2023-04-201-3/+1
| | | | | | | | | Clean up the probe variable declarations by removing the stray newlines. Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-12-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: dwc3: refactor clock lookupsJohan Hovold2023-04-201-55/+61
| | | | | | | | | | The probe callback has become unwieldy so break out the clock lookups into a new helper function to improve readability. Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-11-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: dwc3: refactor phy handlingJohan Hovold2023-04-201-57/+86
| | | | | | | | | | Refactor the PHY handling using four new helpers to initialise, deinitialise, power on and power off all the PHYs. Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-10-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: dwc3: clean up core init error handlingJohan Hovold2023-04-201-17/+13
| | | | | | | | | | Clean up the core init error handling by using descriptive names for the error labels and releasing resourcing in reverse order consistently. Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-9-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: dwc3: clean up phy init error handlingJohan Hovold2023-04-201-9/+9
| | | | | | | | | | | | | | | | | While there likely are no platforms out there that mix generic and legacy PHYs the driver should still be able to handle that, if only for consistency reasons. Add the missing calls to shutdown any legacy PHYs if generic PHY initialisation fails. Note that we continue to happily ignore potential errors from the legacy PHY callbacks... Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-8-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: dwc3: clean up probe error labelsJohan Hovold2023-04-201-23/+22
| | | | | | | | | Use descriptive names consistently for the probe error labels. Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-7-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: dwc3: drop dead hibernation codeJohan Hovold2023-04-202-110/+1
| | | | | | | | | | | | | | | | | | | | The hibernation code is broken and has never been enabled in mainline and should thus be dropped. Specifically, the scratch buffer DMA mapping would have been leaked on every suspend cycle since commit 51f5d49ad6f0 ("usb: dwc3: core: simplify suspend/resume operations") if this feature was ever enabled. The related error handling was also broken and could have resulted in attempts to unmap never mapped buffers, etc. This effectively revert commit 0ffcaf3798bf ("usb: dwc3: core: allocate scratch buffers"). Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-6-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: dwc3: gadget: drop dead hibernation codeJohan Hovold2023-04-201-40/+6
| | | | | | | | | | | | | | | The hibernation code is broken and has never been enabled in mainline and should thus be dropped. Remove the hibernation bits from the gadget code, which effectively reverts commits e1dadd3b0f27 ("usb: dwc3: workaround: bogus hibernation events") and 7b2a0368bbc9 ("usb: dwc3: gadget: set KEEP_CONNECT in case of hibernation") except for the spurious interrupt warning. Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-5-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: dwc3: disable autosuspend on unbindJohan Hovold2023-04-201-0/+2
| | | | | | | | | | Add the missing calls to disable autosuspend on probe errors and on driver unbind. Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-4-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: dwc3: fix runtime pm imbalance on unbindJohan Hovold2023-04-201-0/+1
| | | | | | | | | | | | | | Make sure to balance the runtime PM usage count on driver unbind by adding back the pm_runtime_allow() call that had been erroneously removed. Fixes: 266d0493900a ("usb: dwc3: core: don't trigger runtime pm when remove driver") Cc: stable@vger.kernel.org # 5.9 Cc: Li Jun <jun.li@nxp.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-3-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: dwc3: fix runtime pm imbalance on probe errorsJohan Hovold2023-04-201-9/+5
| | | | | | | | | | | | | Make sure not to suspend the device when probe fails to avoid disabling clocks and phys multiple times. Fixes: 328082376aea ("usb: dwc3: fix runtime PM in error path") Cc: stable@vger.kernel.org # 4.8 Cc: Roger Quadros <rogerq@ti.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20230404072524.19014-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-03 20:10:50 +0000