summaryrefslogtreecommitdiffstats
path: root/drivers/usb
Commit message (Collapse)AuthorAgeFilesLines
* USB: cdc-wdm: fix race between write and disconnect due to flag abuseOliver Neukum2019-08-281-4/+12
| | | | | | | | | | | | | | | | | | | In case of a disconnect an ongoing flush() has to be made fail. Nevertheless we cannot be sure that any pending URB has already finished, so although they will never succeed, they still must not be touched. The clean solution for this is to check for WDM_IN_USE and WDM_DISCONNECTED in flush(). There is no point in ever clearing WDM_IN_USE, as no further writes make sense. The issue is as old as the driver. Fixes: afba937e540c9 ("USB: CDC WDM driver") Reported-by: syzbot+d232cca6ec42c2edb3fc@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190827103436.21143-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: host: xhci: rcar: Fix typo in compatible string matchingGeert Uytterhoeven2019-08-281-1/+1
| | | | | | | | | | | | | It's spelled "renesas", not "renensas". Due to this typo, RZ/G1M and RZ/G1N were not covered by the check. Fixes: 2dc240a3308b ("usb: host: xhci: rcar: retire use of xhci_plat_type_is()") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable <stable@vger.kernel.org> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/20190827125112.12192-1-geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: host: xhci-tegra: Set DMA mask correctlyNagarjuna Kristam2019-08-281-0/+10
| | | | | | | | | | | | | | | | | | | | | | The Falcon microcontroller that runs the XUSB firmware and which is responsible for exposing the XHCI interface can address only 40 bits of memory. Typically that's not a problem because Tegra devices don't have enough system memory to exceed those 40 bits. However, if the ARM SMMU is enable on Tegra186 and later, the addresses passed to the XUSB controller can be anywhere in the 48-bit IOV address space of the ARM SMMU. Since the DMA/IOMMU API starts allocating from the top of the IOVA space, the Falcon microcontroller is not able to load the firmware successfully. Fix this by setting the DMA mask to 40 bits, which will force the DMA API to map the buffer for the firmware to an IOVA that is addressable by the Falcon. Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/1566989697-13049-1-git-send-email-nkristam@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: storage: ums-realtek: Whitelist auto-delink supportKai-Heng Feng2019-08-281-5/+8
| | | | | | | | | | | | | | | | | | Auto-delink requires writing special registers to ums-realtek devices. Unconditionally enable auto-delink may break newer devices. So only enable auto-delink by default for the original three IDs, 0x0138, 0x0158 and 0x0159. Realtek is working on a patch to properly support auto-delink for other IDs. BugLink: https://bugs.launchpad.net/bugs/1838886 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190827173450.13572-2-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: storage: ums-realtek: Update module parameter description for ↵Kai-Heng Feng2019-08-281-1/+1
| | | | | | | | | | | | | | | auto_delink_en The option named "auto_delink_en" is a bit misleading, as setting it to false doesn't really disable auto-delink but let auto-delink be firmware controlled. Update the description to reflect the real usage of this parameter. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190827173450.13572-1-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: host: ohci: fix a race condition between shutdown and irqYoshihiro Shimoda2019-08-281-3/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes an issue that the following error is possible to happen when ohci hardware causes an interruption and the system is shutting down at the same time. [ 34.851754] usb 2-1: USB disconnect, device number 2 [ 35.166658] irq 156: nobody cared (try booting with the "irqpoll" option) [ 35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85 [ 35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) [ 35.187886] Workqueue: usb_hub_wq hub_event [ 35.192063] Call trace: [ 35.194509] dump_backtrace+0x0/0x150 [ 35.198165] show_stack+0x14/0x20 [ 35.201475] dump_stack+0xa0/0xc4 [ 35.204785] __report_bad_irq+0x34/0xe8 [ 35.208614] note_interrupt+0x2cc/0x318 [ 35.212446] handle_irq_event_percpu+0x5c/0x88 [ 35.216883] handle_irq_event+0x48/0x78 [ 35.220712] handle_fasteoi_irq+0xb4/0x188 [ 35.224802] generic_handle_irq+0x24/0x38 [ 35.228804] __handle_domain_irq+0x5c/0xb0 [ 35.232893] gic_handle_irq+0x58/0xa8 [ 35.236548] el1_irq+0xb8/0x180 [ 35.239681] __do_softirq+0x94/0x23c [ 35.243253] irq_exit+0xd0/0xd8 [ 35.246387] __handle_domain_irq+0x60/0xb0 [ 35.250475] gic_handle_irq+0x58/0xa8 [ 35.254130] el1_irq+0xb8/0x180 [ 35.257268] kernfs_find_ns+0x5c/0x120 [ 35.261010] kernfs_find_and_get_ns+0x3c/0x60 [ 35.265361] sysfs_unmerge_group+0x20/0x68 [ 35.269454] dpm_sysfs_remove+0x2c/0x68 [ 35.273284] device_del+0x80/0x370 [ 35.276683] hid_destroy_device+0x28/0x60 [ 35.280686] usbhid_disconnect+0x4c/0x80 [ 35.284602] usb_unbind_interface+0x6c/0x268 [ 35.288867] device_release_driver_internal+0xe4/0x1b0 [ 35.293998] device_release_driver+0x14/0x20 [ 35.298261] bus_remove_device+0x110/0x128 [ 35.302350] device_del+0x148/0x370 [ 35.305832] usb_disable_device+0x8c/0x1d0 [ 35.309921] usb_disconnect+0xc8/0x2d0 [ 35.313663] hub_event+0x6e0/0x1128 [ 35.317146] process_one_work+0x1e0/0x320 [ 35.321148] worker_thread+0x40/0x450 [ 35.324805] kthread+0x124/0x128 [ 35.328027] ret_from_fork+0x10/0x18 [ 35.331594] handlers: [ 35.333862] [<0000000079300c1d>] usb_hcd_irq [ 35.338126] [<0000000079300c1d>] usb_hcd_irq [ 35.342389] Disabling IRQ #156 ohci_shutdown() disables all the interrupt and rh_state is set to OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF is possible to be set by start_ed_unlink() which is called: ohci_irq() -> process_done_list() -> takeback_td() -> start_ed_unlink() So, ohci_irq() has the following condition, the issue happens by &ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and ohci->rh_state = OHCI_RH_HALTED: /* interrupt for some other device? */ if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED)) return IRQ_NOTMINE; To fix the issue, ohci_shutdown() holds the spin lock while disabling the interruption and changing the rh_state flag to prevent reenable the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also calls the ohci_shutdown() and it already held the spin lock, so that the patch makes a new function as _ohci_shutdown(). This patch is inspired by a Renesas R-Car Gen3 BSP patch from Tho Vu. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: hcd: use managed device resourcesSchmid, Carsten2019-08-281-22/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | Using managed device resources in usb_hcd_pci_probe() allows devm usage for resource subranges, such as the mmio resource for the platform device created to control host/device mode mux, which is a xhci extended capability, and sits inside the xhci mmio region. If managed device resources are not used then "parent" resource is released before subrange at driver removal as .remove callback is called before the devres list of resources for this device is walked and released. This has been observed with the xhci extended capability driver causing a use-after-free which is now fixed. An additional nice benefit is that error handling on driver initialisation is simplified much. Signed-off-by: Carsten Schmid <carsten_schmid@mentor.com> Tested-by: Carsten Schmid <carsten_schmid@mentor.com> Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com> Fixes: fa31b3cb2ae1 ("xhci: Add Intel extended cap / otg phy mux handling") Cc: <stable@vger.kernel.org> # v4.19+ Link: https://lore.kernel.org/r/1566569488679.31808@mentor.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* typec: tcpm: fix a typo in the comparison of pdo_max_voltageColin Ian King2019-08-281-1/+1
| | | | | | | | | | | | | | | | There appears to be a typo in the comparison of pdo_max_voltage[i] with the previous value, currently it is checking against the array pdo_min_voltage rather than pdo_max_voltage. I believe this is a typo. Fix this. Addresses-Coverity: ("Copy-paste error") Fixes: 5007e1b5db73 ("typec: tcpm: Validate source and sink caps") Cc: stable <stable@vger.kernel.org> Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20190822135212.10195-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb-storage: Add new JMS567 revision to unusual_devsHenk van der Laan2019-08-211-1/+1
| | | | | | | | | | Revision 0x0117 suffers from an identical issue to earlier revisions, therefore it should be added to the quirks list. Signed-off-by: Henk van der Laan <opensource@henkvdlaan.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190816200847.21366-1-opensource@henkvdlaan.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: udc: don't do hardware access if gadget has stoppedPeter Chen2019-08-211-8/+24
| | | | | | | | | | | | | | | | | | | | | | | | After _gadget_stop_activity is executed, we can consider the hardware operation for gadget has finished, and the udc can be stopped and enter low power mode. So, any later hardware operations (from usb_ep_ops APIs or usb_gadget_ops APIs) should be considered invalid, any deinitializatons has been covered at _gadget_stop_activity. I meet this problem when I plug out usb cable from PC using mass_storage gadget, my callstack like: vbus interrupt->.vbus_session-> composite_disconnect ->pm_runtime_put_sync(&_gadget->dev), the composite_disconnect will call fsg_disable, but fsg_disable calls usb_ep_disable using async way, there are register accesses for usb_ep_disable. So sometimes, I get system hang due to visit register without clock, sometimes not. The Linux Kernel USB maintainer Alan Stern suggests this kinds of solution. See: http://marc.info/?l=linux-usb&m=138541769810983&w=2. Cc: <stable@vger.kernel.org> #v4.9+ Signed-off-by: Peter Chen <peter.chen@nxp.com> Link: https://lore.kernel.org/r/20190820020503.27080-2-peter.chen@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usbtmc: more sanity checking for packet sizeOliver Neukum2019-08-211-0/+3
| | | | | | | | | | A malicious device can make the driver divide ny zero with a nonsense maximum packet size. Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190820092826.17694-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: udc: lpc32xx: silence fall-through warningGustavo A. R. Silva2019-08-211-1/+1
| | | | | | | | | | | Silence the following fall-through warning by adding a break statement: drivers/usb/gadget/udc/lpc32xx_udc.c:2230:3: warning: this statement may fall through [-Wimplicit-fallthrough=] Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Link: https://lore.kernel.org/r/20190821021627.GA2679@embeddedor Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge tag 'usb-serial-5.3-rc5' of ↵Greg Kroah-Hartman2019-08-171-0/+10
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus Johan writes: USB-serial fixes for 5.3-rc5 Here are some new modem device ids. All have been in linux-next with no reported issues. Signed-off-by: Johan Hovold <johan@kernel.org> * tag 'usb-serial-5.3-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: option: add the BroadMobi BM818 card USB: serial: option: Add Motorola modem UARTs USB: serial: option: add D-Link DWM-222 device ID USB: serial: option: Add support for ZTE MF871A
| * USB: serial: option: add the BroadMobi BM818 cardBob Ham2019-08-151-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a VID:PID for the BroadMobi BM818 M.2 card T: Bus=01 Lev=03 Prnt=40 Port=03 Cnt=01 Dev#= 44 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=2060 Rev=00.00 S: Manufacturer=Qualcomm, Incorporated S: Product=Qualcomm CDMA Technologies MSM C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=(none) I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) Signed-off-by: Bob Ham <bob.ham@puri.sm> Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> Cc: stable <stable@vger.kernel.org> [ johan: use USB_DEVICE_INTERFACE_CLASS() ] Signed-off-by: Johan Hovold <johan@kernel.org>
| * USB: serial: option: Add Motorola modem UARTsTony Lindgren2019-08-151-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On Motorola Mapphone devices such as Droid 4 there are five USB ports that do not use the same layout as Gobi 1K/2K/etc devices listed in qcserial.c. So we should use qcaux.c or option.c as noted by Dan Williams <dan.j.williams@intel.com>. As the Motorola USB serial ports have an interrupt endpoint as shown with lsusb -v, we should use option.c instead of qcaux.c as pointed out by Johan Hovold <johan@kernel.org>. The ff/ff/ff interfaces seem to always be UARTs on Motorola devices. For the other interfaces, class 0x0a (CDC Data) should not in general be added as they are typically part of a multi-interface function as noted earlier by Bjørn Mork <bjorn@mork.no>. However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a class is only used for flashing the modem firmware, and there are no other interfaces. So I've added that too with more details below as it works just fine. The ttyUSB ports on Droid 4 are: ttyUSB0 DIAG, CQDM-capable ttyUSB1 MUX or NMEA, no response ttyUSB2 MUX or NMEA, no response ttyUSB3 TCMD ttyUSB4 AT-capable The ttyUSB0 is detected as QCDM capable by ModemManager. I think it's only used for debugging with ModemManager --debug for sending custom AT commands though. ModemManager already can manage data connection using the USB QMI ports that are already handled by the qmi_wwan.c driver. To enable the MUX or NMEA ports, it seems that something needs to be done additionally to enable them, maybe via the DIAG or TCMD port. It might be just a NVRAM setting somewhere, but I have no idea what NVRAM settings may need changing for that. The TCMD port seems to be a Motorola custom protocol for testing the modem and to configure it's NVRAM and seems to work just fine based on a quick test with a minimal tcmdrw tool I wrote. The voice modem AT-capable port seems to provide only partial support, and no PM support compared to the TS 27.010 based UART wired directly to the modem. The UARTs added with this change are the same product IDs as the Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't have any mdm9600 based devices, so I have only tested these on mdm6600 based droid 4. Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android Linux kernel driver moto_flashqsc.c just seems to change the port->bulk_out_size to 8K from the default. And is only used for flashing the modem firmware it seems. I've verified that flashing the modem with signed firmware works just fine with the option driver after manually toggling the GPIO pins, so I've added droid 4 modem flashing mode to the option driver. I've not added the other devices listed in moto_flashqsc.c in case they really need different port->bulk_out_size. Those can be added as they get tested to work for flashing the modem. After this patch the output of /sys/kernel/debug/usb/devices has the following for normal 22b8:2a70 mode including the related qmi_wwan interfaces: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=2a70 Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=8b(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8c(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms In 22b8:900e "qc_dload" mode the device shows up as: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=900e Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms And in 22b8:4281 "ram_downloader" mode the device shows up as: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=4281 Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms Cc: Bjørn Mork <bjorn@mork.no> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Lars Melin <larsm17@gmail.com> Cc: Marcel Partap <mpartap@gmx.net> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Michael Scott <hashcode0f@gmail.com> Cc: NeKit <nekit1000@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Tested-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
| * USB: serial: option: add D-Link DWM-222 device IDRogan Dawes2019-08-051-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add device id for D-Link DWM-222 A2. MI_00 D-Link HS-USB Diagnostics MI_01 D-Link HS-USB Modem MI_02 D-Link HS-USB AT Port MI_03 D-Link HS-USB NMEA MI_04 D-Link HS-USB WWAN Adapter (qmi_wwan) MI_05 USB Mass Storage Device Cc: stable@vger.kernel.org Signed-off-by: Rogan Dawes <rogan@dawes.za.net> Signed-off-by: Johan Hovold <johan@kernel.org>
| * USB: serial: option: Add support for ZTE MF871AYoshiaki Okamoto2019-08-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for MF871A USB modem (aka Speed USB STICK U03) to option driver. This modem is manufactured by ZTE corporation, and sold by KDDI. Interface layout: 0: AT 1: MODEM usb-devices output: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 9 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=1481 Rev=52.87 S: Manufacturer=ZTE,Incorporated S: Product=ZTE Technologies MSM S: SerialNumber=1234567890ABCDEF C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option Co-developed-by: Hiroyuki Yamamoto <hyamamo@allied-telesis.co.jp> Signed-off-by: Hiroyuki Yamamoto <hyamamo@allied-telesis.co.jp> Signed-off-by: Yoshiaki Okamoto <yokamoto@allied-telesis.co.jp> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
* | usb: add a hcd_uses_dma helperChristoph Hellwig2019-08-153-10/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | The USB buffer allocation code is the only place in the usb core (and in fact the whole kernel) that uses is_device_dma_capable, while the URB mapping code uses the uses_dma flag in struct usb_bus. Switch the buffer allocation to use the uses_dma flag used by the rest of the USB code, and create a helper in hcd.h that checks this flag as well as the CONFIG_HAS_DMA to simplify the caller a bit. Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20190811080520.21712-3-hch@lst.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: don't create dma pools for HCDs with a localmem_poolChristoph Hellwig2019-08-151-3/+3
| | | | | | | | | | | | | | | | | | | | If the HCD provides a localmem pool we will never use the DMA pools, so don't create them. Fixes: b0310c2f09bb ("USB: use genalloc for USB HCs with local memory") Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20190811080520.21712-2-hch@lst.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: chipidea: imx: fix EPROBE_DEFER support during driver probeAndré Draszik2019-08-151-7/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If driver probe needs to be deferred, e.g. because ci_hdrc_add_device() isn't ready yet, this driver currently misbehaves badly: a) success is still reported to the driver core (meaning a 2nd probe attempt will never be done), leaving the driver in a dysfunctional state and the hardware unusable b) driver remove / shutdown OOPSes: [ 206.786916] Unable to handle kernel paging request at virtual address fffffdff [ 206.794148] pgd = 880b9f82 [ 206.796890] [fffffdff] *pgd=abf5e861, *pte=00000000, *ppte=00000000 [ 206.803179] Internal error: Oops: 37 [#1] PREEMPT SMP ARM [ 206.808581] Modules linked in: wl18xx evbug [ 206.813308] CPU: 1 PID: 1 Comm: systemd-shutdow Not tainted 4.19.35+gf345c93b4195 #1 [ 206.821053] Hardware name: Freescale i.MX7 Dual (Device Tree) [ 206.826813] PC is at ci_hdrc_remove_device+0x4/0x20 [ 206.831699] LR is at ci_hdrc_imx_remove+0x20/0xe8 [ 206.836407] pc : [<805cd4b0>] lr : [<805d62cc>] psr: 20000013 [ 206.842678] sp : a806be40 ip : 00000001 fp : 80adbd3c [ 206.847906] r10: 80b1b794 r9 : 80d5dfe0 r8 : a8192c44 [ 206.853136] r7 : 80db93a0 r6 : a8192c10 r5 : a8192c00 r4 : a93a4a00 [ 206.859668] r3 : 00000000 r2 : a8192ce4 r1 : ffffffff r0 : fffffdfb [ 206.866201] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [ 206.873341] Control: 10c5387d Table: a9e0c06a DAC: 00000051 [ 206.879092] Process systemd-shutdow (pid: 1, stack limit = 0xb271353c) [ 206.885624] Stack: (0xa806be40 to 0xa806c000) [ 206.889992] be40: a93a4a00 805d62cc a8192c1c a8170e10 a8192c10 8049a490 80d04d08 00000000 [ 206.898179] be60: 00000000 80d0da2c fee1dead 00000000 a806a000 00000058 00000000 80148b08 [ 206.906366] be80: 01234567 80148d8c a9858600 00000000 00000000 00000000 00000000 80d04d08 [ 206.914553] bea0: 00000000 00000000 a82741e0 a9858600 00000024 00000002 a9858608 00000005 [ 206.922740] bec0: 0000001e 8022c058 00000000 00000000 a806bf14 a9858600 00000000 a806befc [ 206.930927] bee0: a806bf78 00000000 7ee12c30 8022c18c a806bef8 a806befc 00000000 00000001 [ 206.939115] bf00: 00000000 00000024 a806bf14 00000005 7ee13b34 7ee12c68 00000004 7ee13f20 [ 206.947302] bf20: 00000010 7ee12c7c 00000005 7ee12d04 0000000a 76e7dc00 00000001 80d0f140 [ 206.955490] bf40: ab637880 a974de40 60000013 80d0f140 ab6378a0 80d04d08 a8080470 a9858600 [ 206.963677] bf60: a9858600 00000000 00000000 8022c24c 00000000 80144310 00000000 00000000 [ 206.971864] bf80: 80101204 80d04d08 00000000 80d04d08 00000000 00000000 00000003 00000058 [ 206.980051] bfa0: 80101204 80101000 00000000 00000000 fee1dead 28121969 01234567 00000000 [ 206.988237] bfc0: 00000000 00000000 00000003 00000058 00000000 00000000 00000000 00000000 [ 206.996425] bfe0: 0049ffb0 7ee13d58 0048a84b 76f245a6 60000030 fee1dead 00000000 00000000 [ 207.004622] [<805cd4b0>] (ci_hdrc_remove_device) from [<805d62cc>] (ci_hdrc_imx_remove+0x20/0xe8) [ 207.013509] [<805d62cc>] (ci_hdrc_imx_remove) from [<8049a490>] (device_shutdown+0x16c/0x218) [ 207.022050] [<8049a490>] (device_shutdown) from [<80148b08>] (kernel_restart+0xc/0x50) [ 207.029980] [<80148b08>] (kernel_restart) from [<80148d8c>] (sys_reboot+0xf4/0x1f0) [ 207.037648] [<80148d8c>] (sys_reboot) from [<80101000>] (ret_fast_syscall+0x0/0x54) [ 207.045308] Exception stack(0xa806bfa8 to 0xa806bff0) [ 207.050368] bfa0: 00000000 00000000 fee1dead 28121969 01234567 00000000 [ 207.058554] bfc0: 00000000 00000000 00000003 00000058 00000000 00000000 00000000 00000000 [ 207.066737] bfe0: 0049ffb0 7ee13d58 0048a84b 76f245a6 [ 207.071799] Code: ebffffa8 e3a00000 e8bd8010 e92d4010 (e5904004) [ 207.078021] ---[ end trace be47424e3fd46e9f ]--- [ 207.082647] Kernel panic - not syncing: Fatal exception [ 207.087894] ---[ end Kernel panic - not syncing: Fatal exception ]--- c) the error path in combination with driver removal causes imbalanced calls to the clk_*() and pm_()* APIs a) happens because the original intended return value is overwritten (with 0) by the return code of regulator_disable() in ci_hdrc_imx_probe()'s error path b) happens because ci_pdev is -EPROBE_DEFER, which causes ci_hdrc_remove_device() to OOPS Fix a) by being more careful in ci_hdrc_imx_probe()'s error path and not overwriting the real error code Fix b) by calling the respective cleanup functions during remove only when needed (when ci_pdev != NULL, i.e. when everything was initialised correctly). This also has the side effect of not causing imbalanced clk_*() and pm_*() API calls as part of the error code path. Fixes: 7c8e8909417e ("usb: chipidea: imx: add HSIC support") Signed-off-by: André Draszik <git@andred.net> Cc: stable <stable@vger.kernel.org> CC: Peter Chen <Peter.Chen@nxp.com> CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org> CC: Shawn Guo <shawnguo@kernel.org> CC: Sascha Hauer <s.hauer@pengutronix.de> CC: Pengutronix Kernel Team <kernel@pengutronix.de> CC: Fabio Estevam <festevam@gmail.com> CC: NXP Linux Team <linux-imx@nxp.com> CC: linux-usb@vger.kernel.org CC: linux-arm-kernel@lists.infradead.org CC: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190810150758.17694-1-git@andred.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: host: fotg2: restart hcd after port resetHans Ulli Kroll2019-08-151-0/+4
| | | | | | | | | | | | | | | | | | | | On the Gemini SoC the FOTG2 stalls after port reset so restart the HCD after each port reset. Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190810150458.817-1-linus.walleij@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | USB: CDC: fix sanity checks in CDC union parserOliver Neukum2019-08-151-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | A few checks checked for the size of the pointer to a structure instead of the structure itself. Copy & paste issue presumably. Fixes: e4c6fb7794982 ("usbnet: move the CDC parser into USB core") Cc: stable <stable@vger.kernel.org> Reported-by: syzbot+45a53506b65321c1fe91@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20190813093541.18889-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: cdc-acm: make sure a refcount is taken early enoughOliver Neukum2019-08-151-5/+7
| | | | | | | | | | | | | | | | | | | | | | | | destroy() will decrement the refcount on the interface, so that it needs to be taken so early that it never undercounts. Fixes: 7fb57a019f94e ("USB: cdc-acm: Fix potential deadlock (lockdep warning)") Cc: stable <stable@vger.kernel.org> Reported-and-tested-by: syzbot+1b2449b7b5dc240d107a@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20190808142119.7998-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | USB: core: Fix races in character device registration and deregistraionAlan Stern2019-08-121-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The syzbot fuzzer has found two (!) races in the USB character device registration and deregistration routines. This patch fixes the races. The first race results from the fact that usb_deregister_dev() sets usb_minors[intf->minor] to NULL before calling device_destroy() on the class device. This leaves a window during which another thread can allocate the same minor number but will encounter a duplicate name error when it tries to register its own class device. A typical error message in the system log would look like: sysfs: cannot create duplicate filename '/class/usbmisc/ldusb0' The patch fixes this race by destroying the class device first. The second race is in usb_register_dev(). When that routine runs, it first allocates a minor number, then drops minor_rwsem, and then creates the class device. If the device creation fails, the minor number is deallocated and the whole routine returns an error. But during the time while minor_rwsem was dropped, there is a window in which the minor number is allocated and so another thread can successfully open the device file. Typically this results in use-after-free errors or invalid accesses when the other thread closes its open file reference, because the kernel then tries to release resources that were already deallocated when usb_register_dev() failed. The patch fixes this race by keeping minor_rwsem locked throughout the entire routine. Reported-and-tested-by: syzbot+30cf45ebfe0b0c4847a1@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1908121607590.1659-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: gadget: mass_storage: Fix races between fsg_disable and fsg_set_altBenjamin Herrenschmidt2019-08-121-10/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If fsg_disable() and fsg_set_alt() are called too closely to each other (for example due to a quick reset/reconnect), what can happen is that fsg_set_alt sets common->new_fsg from an interrupt while handle_exception is trying to process the config change caused by fsg_disable(): fsg_disable() ... handle_exception() sets state back to FSG_STATE_NORMAL hasn't yet called do_set_interface() or is inside it. ---> interrupt fsg_set_alt sets common->new_fsg queues a new FSG_STATE_CONFIG_CHANGE <--- Now, the first handle_exception can "see" the updated new_fsg, treats it as if it was a fsg_set_alt() response, call usb_composite_setup_continue() etc... But then, the thread sees the second FSG_STATE_CONFIG_CHANGE, and goes back down the same path, wipes and reattaches a now active fsg, and .. calls usb_composite_setup_continue() which at this point is wrong. Not only we get a backtrace, but I suspect the second set_interface wrecks some state causing the host to get upset in my case. This fixes it by replacing "new_fsg" by a "state argument" (same principle) which is set in the same lock section as the state update, and retrieved similarly. That way, there is never any discrepancy between the dequeued state and the observed value of it. We keep the ability to have the latest reconfig operation take precedence, but we guarantee that once "dequeued" the argument (new_fsg) will not be clobbered by any new event. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* | usb: gadget: composite: Clear "suspended" on reset/disconnectBenjamin Herrenschmidt2019-08-121-0/+1
| | | | | | | | | | | | | | | | | | In some cases, one can get out of suspend with a reset or a disconnect followed by a reconnect. Previously we would leave a stale suspended flag set. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* | usb: gadget: udc: renesas_usb3: Fix sysfs interface of "role"Yoshihiro Shimoda2019-08-121-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | Since the role_store() uses strncmp(), it's possible to refer out-of-memory if the sysfs data size is smaller than strlen("host"). This patch fixes it by using sysfs_streq() instead of strncmp(). Fixes: cc995c9ec118 ("usb: gadget: udc: renesas_usb3: add support for usb role swap") Cc: <stable@vger.kernel.org> # v4.12+ Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* | usb: setup authorized_default attributes using usb_bus_notifyThiébaud Weksteen2019-08-083-123/+126
| | | | | | | | | | | | | | | | | | | | | | | | | | Currently, the authorized_default and interface_authorized_default attributes for HCD are set up after the uevent has been sent to userland. This creates a race condition where userland may fail to access this file when processing the event. Move the appending of these attributes earlier relying on the usb_bus_notify dispatcher. Signed-off-by: Thiébaud Weksteen <tweek@google.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190806110050.38918-1-tweek@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: iowarrior: fix deadlock on disconnectOliver Neukum2019-08-081-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | We have to drop the mutex before we close() upon disconnect() as close() needs the lock. This is safe to do by dropping the mutex as intfdata is already set to NULL, so open() will fail. Fixes: 03f36e885fc26 ("USB: open disconnect race in iowarrior") Reported-by: syzbot+a64a382964bf6c71a9c0@syzkaller.appspotmail.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20190808092728.23417-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | Revert "USB: rio500: simplify locking"Oliver Neukum2019-08-081-16/+27
| | | | | | | | | | | | | | | | | | | | | | | | This reverts commit d710734b06770814de2bfa2819420fb5df7f3a81. This simplification causes a deadlock. Reported-by: syzbot+7bbcbe9c9ff0cd49592a@syzkaller.appspotmail.com Fixes: d710734b0677 ("USB: rio500: simplify locking") Cc: stable <stable@vger.kernel.org> Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20190808092854.23519-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: usbfs: fix double-free of usb memory upon submiturb errorGavin Li2019-08-051-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | Upon an error within proc_do_submiturb(), dec_usb_memory_use_count() gets called once by the error handling tail and again by free_async(). Remove the first call. Signed-off-by: Gavin Li <git@thegavinli.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190804235044.22327-1-gavinli@thegavinli.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: yurex: Fix use-after-free in yurex_deleteSuzuki K Poulose2019-08-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | syzbot reported the following crash [0]: BUG: KASAN: use-after-free in usb_free_coherent+0x79/0x80 drivers/usb/core/usb.c:928 Read of size 8 at addr ffff8881b18599c8 by task syz-executor.4/16007 CPU: 0 PID: 16007 Comm: syz-executor.4 Not tainted 5.3.0-rc2+ #23 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x6a/0x32c mm/kasan/report.c:351 __kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482 kasan_report+0xe/0x12 mm/kasan/common.c:612 usb_free_coherent+0x79/0x80 drivers/usb/core/usb.c:928 yurex_delete+0x138/0x330 drivers/usb/misc/yurex.c:100 kref_put include/linux/kref.h:65 [inline] yurex_release+0x66/0x90 drivers/usb/misc/yurex.c:392 __fput+0x2d7/0x840 fs/file_table.c:280 task_work_run+0x13f/0x1c0 kernel/task_work.c:113 tracehook_notify_resume include/linux/tracehook.h:188 [inline] exit_to_usermode_loop+0x1d2/0x200 arch/x86/entry/common.c:163 prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline] syscall_return_slowpath arch/x86/entry/common.c:274 [inline] do_syscall_64+0x45f/0x580 arch/x86/entry/common.c:299 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x413511 Code: 75 14 b8 03 00 00 00 0f 05 48 3d 01 f0 ff ff 0f 83 04 1b 00 00 c3 48 83 ec 08 e8 0a fc ff ff 48 89 04 24 b8 03 00 00 00 0f 05 <48> 8b 3c 24 48 89 c2 e8 53 fc ff ff 48 89 d0 48 83 c4 08 48 3d 01 RSP: 002b:00007ffc424ea2e0 EFLAGS: 00000293 ORIG_RAX: 0000000000000003 RAX: 0000000000000000 RBX: 0000000000000007 RCX: 0000000000413511 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000006 RBP: 0000000000000001 R08: 0000000029a2fc22 R09: 0000000029a2fc26 R10: 00007ffc424ea3c0 R11: 0000000000000293 R12: 000000000075c9a0 R13: 000000000075c9a0 R14: 0000000000761938 R15: ffffffffffffffff Allocated by task 2776: save_stack+0x1b/0x80 mm/kasan/common.c:69 set_track mm/kasan/common.c:77 [inline] __kasan_kmalloc mm/kasan/common.c:487 [inline] __kasan_kmalloc.constprop.0+0xbf/0xd0 mm/kasan/common.c:460 kmalloc include/linux/slab.h:552 [inline] kzalloc include/linux/slab.h:748 [inline] usb_alloc_dev+0x51/0xf95 drivers/usb/core/usb.c:583 hub_port_connect drivers/usb/core/hub.c:5004 [inline] hub_port_connect_change drivers/usb/core/hub.c:5213 [inline] port_event drivers/usb/core/hub.c:5359 [inline] hub_event+0x15c0/0x3640 drivers/usb/core/hub.c:5441 process_one_work+0x92b/0x1530 kernel/workqueue.c:2269 worker_thread+0x96/0xe20 kernel/workqueue.c:2415 kthread+0x318/0x420 kernel/kthread.c:255 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352 Freed by task 16007: save_stack+0x1b/0x80 mm/kasan/common.c:69 set_track mm/kasan/common.c:77 [inline] __kasan_slab_free+0x130/0x180 mm/kasan/common.c:449 slab_free_hook mm/slub.c:1423 [inline] slab_free_freelist_hook mm/slub.c:1470 [inline] slab_free mm/slub.c:3012 [inline] kfree+0xe4/0x2f0 mm/slub.c:3953 device_release+0x71/0x200 drivers/base/core.c:1064 kobject_cleanup lib/kobject.c:693 [inline] kobject_release lib/kobject.c:722 [inline] kref_put include/linux/kref.h:65 [inline] kobject_put+0x171/0x280 lib/kobject.c:739 put_device+0x1b/0x30 drivers/base/core.c:2213 usb_put_dev+0x1f/0x30 drivers/usb/core/usb.c:725 yurex_delete+0x40/0x330 drivers/usb/misc/yurex.c:95 kref_put include/linux/kref.h:65 [inline] yurex_release+0x66/0x90 drivers/usb/misc/yurex.c:392 __fput+0x2d7/0x840 fs/file_table.c:280 task_work_run+0x13f/0x1c0 kernel/task_work.c:113 tracehook_notify_resume include/linux/tracehook.h:188 [inline] exit_to_usermode_loop+0x1d2/0x200 arch/x86/entry/common.c:163 prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline] syscall_return_slowpath arch/x86/entry/common.c:274 [inline] do_syscall_64+0x45f/0x580 arch/x86/entry/common.c:299 entry_SYSCALL_64_after_hwframe+0x49/0xbe The buggy address belongs to the object at ffff8881b1859980 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 72 bytes inside of 2048-byte region [ffff8881b1859980, ffff8881b185a180) The buggy address belongs to the page: page:ffffea0006c61600 refcount:1 mapcount:0 mapping:ffff8881da00c000 index:0x0 compound_mapcount: 0 flags: 0x200000000010200(slab|head) raw: 0200000000010200 0000000000000000 0000000100000001 ffff8881da00c000 raw: 0000000000000000 00000000000f000f 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8881b1859880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881b1859900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc > ffff8881b1859980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff8881b1859a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881b1859a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== A quick look at the yurex_delete() shows that we drop the reference to the usb_device before releasing any buffers associated with the device. Delay the reference drop until we have finished the cleanup. [0] https://lore.kernel.org/lkml/0000000000003f86d8058f0bd671@google.com/ Fixes: 6bc235a2e24a5e ("USB: add driver for Meywa-Denki & Kayac YUREX") Cc: Jiri Kosina <jkosina@suse.cz> Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com> Cc: Oliver Neukum <oneukum@suse.com> Cc: andreyknvl@google.com Cc: gregkh@linuxfoundation.org Cc: Alan Stern <stern@rowland.harvard.edu> Cc: syzkaller-bugs@googlegroups.com Cc: dtor@chromium.org Reported-by: syzbot+d1fedb1c1fdb07fca507@syzkaller.appspotmail.com Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190805111528.6758-1-suzuki.poulose@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: typec: tcpm: Ignore unsupported/unknown alternate mode requestsGuenter Roeck2019-08-021-14/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TCPM may receive PD messages associated with unknown or unsupported alternate modes. If that happens, calls to typec_match_altmode() will return NULL. The tcpm code does not currently take this into account. This results in crashes. Unable to handle kernel NULL pointer dereference at virtual address 000001f0 pgd = 41dad9a1 [000001f0] *pgd=00000000 Internal error: Oops: 5 [#1] THUMB2 Modules linked in: tcpci tcpm CPU: 0 PID: 2338 Comm: kworker/u2:0 Not tainted 5.1.18-sama5-armv7-r2 #6 Hardware name: Atmel SAMA5 Workqueue: 2-0050 tcpm_pd_rx_handler [tcpm] PC is at typec_altmode_attention+0x0/0x14 LR is at tcpm_pd_rx_handler+0xa3b/0xda0 [tcpm] ... [<c03fbee8>] (typec_altmode_attention) from [<bf8030fb>] (tcpm_pd_rx_handler+0xa3b/0xda0 [tcpm]) [<bf8030fb>] (tcpm_pd_rx_handler [tcpm]) from [<c012082b>] (process_one_work+0x123/0x2a8) [<c012082b>] (process_one_work) from [<c0120a6d>] (worker_thread+0xbd/0x3b0) [<c0120a6d>] (worker_thread) from [<c012431f>] (kthread+0xcf/0xf4) [<c012431f>] (kthread) from [<c01010f9>] (ret_from_fork+0x11/0x38) Ignore PD messages if the associated alternate mode is not supported. Fixes: e9576fe8e605c ("usb: typec: tcpm: Support for Alternate Modes") Cc: stable <stable@vger.kernel.org> Reported-by: Douglas Gilbert <dgilbert@interlog.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/1564761822-13984-1-git-send-email-linux@roeck-us.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | xhci: Fix NULL pointer dereference at endpoint zero reset.Mathias Nyman2019-08-021-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Usb core will reset the default control endpoint "ep0" before resetting a device. if the endpoint has a valid pointer back to the usb device then the xhci driver reset callback will try to clear the toggle for the endpoint. ep0 didn't use to have this pointer set as ep0 was always allocated by default together with a xhci slot for the usb device. Other endpoints got their usb device pointer set in xhci_add_endpoint() This changed with commit ef513be0a905 ("usb: xhci: Add Clear_TT_Buffer") which sets the pointer for any endpoint on a FS/LS device behind a HS hub that halts, including ep0. If xHC controller needs to be reset at resume, then all the xhci slots will be lost. Slots will be reenabled and reallocated at device reset, but unlike other endpoints the ep0 is reset before device reset, while the xhci slot may still be invalid, causing NULL pointer dereference. Fix it by checking that the endpoint has both a usb device pointer and valid xhci slot before trying to clear the toggle. This issue was not seen earlier as ep0 didn't use to have a valid usb device pointer, and other endpoints were only reset after device reset when xhci slots were properly reenabled. Reported-by: Bob Gleitsmann <rjgleits@bellsouth.net> Reported-by: Enric Balletbo Serra <eballetbo@gmail.com> Fixes: ef513be0a905 ("usb: xhci: Add Clear_TT_Buffer") Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Link: https://lore.kernel.org/r/1564758044-24748-1-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: host: xhci-rcar: Fix timeout in xhci_suspend()Yoshihiro Shimoda2019-08-021-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When a USB device is connected to the host controller and the system enters suspend, the following error happens in xhci_suspend(): xhci-hcd ee000000.usb: WARN: xHC CMD_RUN timeout Since the firmware/internal CPU control the USBSTS.STS_HALT and the process speed is down when the roothub port enters U3, long delay for the handshake of STS_HALT is neeed in xhci_suspend(). So, this patch adds to set the XHCI_SLOW_SUSPEND. Fixes: 435cc1138ec9 ("usb: host: xhci-plat: set resume_quirk() for R-Car controllers") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/1564734815-17964-1-git-send-email-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: typec: ucsi: ccg: Fix uninitilized symbol errorHeikki Krogerus2019-08-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Fix smatch error: drivers/usb/typec/ucsi/ucsi_ccg.c:975 ccg_fw_update() error: uninitialized symbol 'err'. Fixes: 5c9ae5a87573 ("usb: typec: ucsi: ccg: add firmware flashing support") Cc: stable@vger.kernel.org Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20190801075512.24354-1-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: typec: tcpm: remove tcpm dir if no childrenLi Jun2019-07-301-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If config tcpm as module, module unload will not remove tcpm dir, then the next module load will have problem: the rootdir is NULL but tcpm dir is still there, so tcpm_debugfs_init() will create tcpm dir again with failure, fix it by remove the tcpm dir if no children. Cc: stable@vger.kernel.org # v4.15+ Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging") Signed-off-by: Li Jun <jun.li@nxp.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20190717080646.30421-2-jun.li@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: typec: tcpm: free log buf memory when remove debug fileLi Jun2019-07-301-0/+9
| | | | | | | | | | | | | | | | | | | | | | The logbuffer memory should be freed when remove debug file. Cc: stable@vger.kernel.org # v4.15+ Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging") Signed-off-by: Li Jun <jun.li@nxp.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20190717080646.30421-1-jun.li@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: typec: tcpm: Add NULL check before dereferencing configGuenter Roeck2019-07-301-3/+4
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When instantiating tcpm on an NXP OM 13588 board with NXP PTN5110, the following crash is seen when writing into the 'preferred_role' sysfs attribute. Unable to handle kernel NULL pointer dereference at virtual address 00000028 pgd = f69149ad [00000028] *pgd=00000000 Internal error: Oops: 5 [#1] THUMB2 Modules linked in: tcpci tcpm CPU: 0 PID: 1882 Comm: bash Not tainted 5.1.18-sama5-armv7-r2 #4 Hardware name: Atmel SAMA5 PC is at tcpm_try_role+0x3a/0x4c [tcpm] LR is at tcpm_try_role+0x15/0x4c [tcpm] pc : [<bf8000e2>] lr : [<bf8000bd>] psr: 60030033 sp : dc1a1e88 ip : c03fb47d fp : 00000000 r10: dc216190 r9 : dc1a1f78 r8 : 00000001 r7 : df4ae044 r6 : dd032e90 r5 : dd1ce340 r4 : df4ae054 r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : df4ae044 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment none Control: 50c53c7d Table: 3efec059 DAC: 00000051 Process bash (pid: 1882, stack limit = 0x6a6d4aa5) Stack: (0xdc1a1e88 to 0xdc1a2000) 1e80: dd05d808 dd1ce340 00000001 00000007 dd1ce340 c03fb4a7 1ea0: 00000007 00000007 dc216180 00000000 00000000 c01e1e03 00000000 00000000 1ec0: c0907008 dee98b40 c01e1d5d c06106c4 00000000 00000000 00000007 c0194e8b 1ee0: 0000000a 00000400 00000000 c01a97db dc22bf00 ffffe000 df4b6a00 df745900 1f00: 00000001 00000001 000000dd c01a9c2f 7aeab3be c0907008 00000000 dc22bf00 1f20: c0907008 00000000 00000000 00000000 00000000 7aeab3be 00000007 dee98b40 1f40: 005dc318 dc1a1f78 00000000 00000000 00000007 c01969f7 0000000a c01a20cb 1f60: dee98b40 c0907008 dee98b40 005dc318 00000000 c0196b9b 00000000 00000000 1f80: dee98b40 7aeab3be 00000074 005dc318 b6f3bdb0 00000004 c0101224 dc1a0000 1fa0: 00000004 c0101001 00000074 005dc318 00000001 005dc318 00000007 00000000 1fc0: 00000074 005dc318 b6f3bdb0 00000004 00000007 00000007 00000000 00000000 1fe0: 00000004 be800880 b6ed35b3 b6e5c746 60030030 00000001 00000000 00000000 [<bf8000e2>] (tcpm_try_role [tcpm]) from [<c03fb4a7>] (preferred_role_store+0x2b/0x5c) [<c03fb4a7>] (preferred_role_store) from [<c01e1e03>] (kernfs_fop_write+0xa7/0x150) [<c01e1e03>] (kernfs_fop_write) from [<c0194e8b>] (__vfs_write+0x1f/0x104) [<c0194e8b>] (__vfs_write) from [<c01969f7>] (vfs_write+0x6b/0x104) [<c01969f7>] (vfs_write) from [<c0196b9b>] (ksys_write+0x43/0x94) [<c0196b9b>] (ksys_write) from [<c0101001>] (ret_fast_syscall+0x1/0x62) Since commit 96232cbc6c994 ("usb: typec: tcpm: support get typec and pd config from device properties"), the 'config' pointer in struct tcpc_dev is optional when registering a Type-C port. Since it is optional, we have to check if it is NULL before dereferencing it. Reported-by: Douglas Gilbert <dgilbert@interlog.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Fixes: 96232cbc6c994 ("usb: typec: tcpm: support get typec and pd config from device properties") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: stable <stable@vger.kernel.org> Reviewed-by: Jun Li <jun.li@nxp.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/1563979112-22483-1-git-send-email-linux@roeck-us.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* xhci: Fix crash if scatter gather is used with Immediate Data Transfer (IDT).Mathias Nyman2019-07-251-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | A second regression was found in the immediate data transfer (IDT) support which was added to 5.2 kernel IDT is used to transfer small amounts of data (up to 8 bytes) in the field normally used for data dma address, thus avoiding dma mapping. If the data was not already dma mapped, then IDT support assumed data was in urb->transfer_buffer, and did not take into accound that even small amounts of data (8 bytes) can be in a scatterlist instead. This caused a NULL pointer dereference when sg_dma_len() was used with non-dma mapped data. Solve this by not using IDT if scatter gather buffer list is used. Fixes: 33e39350ebd2 ("usb: xhci: add Immediate Data Transfer support") Cc: <stable@vger.kernel.org> # v5.2 Reported-by: Maik Stohn <maik.stohn@seal-one.com> Tested-by: Maik Stohn <maik.stohn@seal-one.com> CC: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1564044861-1445-1-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: usb251xb: Reallow swap-dx-lanes to apply to the upstream portLucas Stach2019-07-251-6/+7
| | | | | | | | | | | | | | | | | | | | This is a partial revert of 73d31def1aab "usb: usb251xb: Create a ports field collector method", which broke a existing devicetree (arch/arm64/boot/dts/freescale/imx8mq.dtsi). There is no reason why the swap-dx-lanes property should not apply to the upstream port. The reason given in the breaking commit was that it's inconsitent with respect to other port properties, but in fact it is not. All other properties which only apply to the downstream ports explicitly reject port 0, so there is pretty strong precedence that the driver referred to the upstream port as port 0. So there is no inconsistency in this property at all, other than the swapping being also applicable to the upstream port. CC: stable@vger.kernel.org #5.2 Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Link: https://lore.kernel.org/r/20190719084407.28041-3-l.stach@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Revert "usb: usb251xb: Add US port lanes inversion property"Lucas Stach2019-07-251-2/+0
| | | | | | | | | | | This property isn't needed and not yet used anywhere. The swap-dx-lanes property is perfectly fine for doing the swap on the upstream port lanes. CC: stable@vger.kernel.org #5.2 Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Link: https://lore.kernel.org/r/20190719084407.28041-2-l.stach@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: wusbcore: fix unbalanced get/put cluster_idPhong Tran2019-07-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | syzboot reported that https://syzkaller.appspot.com/bug?extid=fd2bd7df88c606eea4ef There is not consitency parameter in cluste_id_get/put calling. In case of getting the id with result is failure, the wusbhc->cluster_id will not be updated and this can not be used for wusb_cluster_id_put(). Tested report https://groups.google.com/d/msg/syzkaller-bugs/0znZopp3-9k/oxOrhLkLEgAJ Reproduce and gdb got the details: 139 addr = wusb_cluster_id_get(); (gdb) n 140 if (addr == 0) (gdb) print addr $1 = 254 '\376' (gdb) n 142 result = __hwahc_set_cluster_id(hwahc, addr); (gdb) print result $2 = -71 (gdb) break wusb_cluster_id_put Breakpoint 3 at 0xffffffff836e3f20: file drivers/usb/wusbcore/wusbhc.c, line 384. (gdb) s Thread 2 hit Breakpoint 3, wusb_cluster_id_put (id=0 '\000') at drivers/usb/wusbcore/wusbhc.c:384 384 id = 0xff - id; (gdb) n 385 BUG_ON(id >= CLUSTER_IDS); (gdb) print id $3 = 255 '\377' Reported-by: syzbot+fd2bd7df88c606eea4ef@syzkaller.appspotmail.com Signed-off-by: Phong Tran <tranmanphong@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190724020601.15257-1-tranmanphong@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb/hcd: Fix a NULL vs IS_ERR() bug in usb_hcd_setup_local_mem()Dan Carpenter2019-07-251-2/+2
| | | | | | | | | | | The devm_memremap() function doesn't return NULL, it returns error pointers. Fixes: b0310c2f09bb ("USB: use genalloc for USB HCs with local memory") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20190607135709.GC16718@mwanda Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb-storage: Add a limitation for blk_queue_max_hw_sectors()Yoshihiro Shimoda2019-07-251-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes an issue that the following error happens on swiotlb environment: xhci-hcd ee000000.usb: swiotlb buffer is full (sz: 524288 bytes), total 32768 (slots), used 1338 (slots) On the kernel v5.1, block settings of a usb-storage with SuperSpeed were the following so that the block layer will allocate buffers up to 64 KiB, and then the issue didn't happen. max_segment_size = 65536 max_hw_sectors_kb = 1024 After the commit 09324d32d2a0 ("block: force an unlimited segment size on queues with a virt boundary") is applied, the block settings are the following. So, the block layer will allocate buffers up to 1024 KiB, and then the issue happens: max_segment_size = 4294967295 max_hw_sectors_kb = 1024 To fix the issue, the usb-storage driver checks the maximum size of a mapping for the device and then adjusts the max_hw_sectors_kb if required. After this patch is applied, the block settings will be the following, and then the issue doesn't happen. max_segment_size = 4294967295 max_hw_sectors_kb = 256 Fixes: 09324d32d2a0 ("block: force an unlimited segment size on queues with a virt boundary") Cc: stable <stable@vger.kernel.org> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/1563793105-20597-1-git-send-email-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: pci-quirks: Minor cleanup for AMD PLL quirkRyan Kennedy2019-07-255-19/+21
| | | | | | | | | | | | | | usb_amd_find_chipset_info() is used for chipset detection for several quirks. It is strange that its return value indicates the need for the PLL quirk, which means it is often ignored. This patch adds a function specifically for checking the PLL quirk like the other ones. Additionally, rename probe_result to something more appropriate. Signed-off-by: Ryan Kennedy <ryan5544@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20190704153529.9429-3-ryan5544@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: pci-quirks: Correct AMD PLL quirk detectionRyan Kennedy2019-07-251-12/+19
| | | | | | | | | | | | | | | | | The AMD PLL USB quirk is incorrectly enabled on newer Ryzen chipsets. The logic in usb_amd_find_chipset_info currently checks for unaffected chipsets rather than affected ones. This broke once a new chipset was added in e788787ef. It makes more sense to reverse the logic so it won't need to be updated as new chipsets are added. Note that the core of the workaround in usb_amd_quirk_pll does correctly check the chipset. Signed-off-by: Ryan Kennedy <ryan5544@gmail.com> Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume") Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20190704153529.9429-2-ryan5544@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge branch 'work.mount0' of ↵Linus Torvalds2019-07-191-6/+15
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull vfs mount updates from Al Viro: "The first part of mount updates. Convert filesystems to use the new mount API" * 'work.mount0' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits) mnt_init(): call shmem_init() unconditionally constify ksys_mount() string arguments don't bother with registering rootfs init_rootfs(): don't bother with init_ramfs_fs() vfs: Convert smackfs to use the new mount API vfs: Convert selinuxfs to use the new mount API vfs: Convert securityfs to use the new mount API vfs: Convert apparmorfs to use the new mount API vfs: Convert openpromfs to use the new mount API vfs: Convert xenfs to use the new mount API vfs: Convert gadgetfs to use the new mount API vfs: Convert oprofilefs to use the new mount API vfs: Convert ibmasmfs to use the new mount API vfs: Convert qib_fs/ipathfs to use the new mount API vfs: Convert efivarfs to use the new mount API vfs: Convert configfs to use the new mount API vfs: Convert binfmt_misc to use the new mount API convenience helper: get_tree_single() convenience helper get_tree_nodev() vfs: Kill sget_userns() ...
| * vfs: Convert gadgetfs to use the new mount APIDavid Howells2019-07-041-6/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Convert the gadgetfs filesystem to the new internal mount API as the old one will be obsoleted and removed. This allows greater flexibility in communication of mount parameters between userspace, the VFS and the filesystem. See Documentation/filesystems/mount_api.txt for more information. Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> cc: linux-usb@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* | Merge branch 'i2c/for-5.3' of ↵Linus Torvalds2019-07-153-4/+125
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c updates from Wolfram Sang: "New stuff from the I2C world: - in the core, getting irqs from ACPI is now similar to OF - new driver for MediaTek MT7621/7628/7688 SoCs - bcm2835, i801, and tegra drivers got some more attention - GPIO API cleanups - cleanups in the core headers - lots of usual driver updates" * 'i2c/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (74 commits) i2c: mt7621: Fix platform_no_drv_owner.cocci warnings i2c: cpm: remove casting dma_alloc dt-bindings: i2c: sun6i-p2wi: Fix the binding example dt-bindings: i2c: mv64xxx: Fix the example compatible i2c: i801: Documentation update i2c: i801: Add support for Intel Tiger Lake i2c: i801: Fix PCI ID sorting dt-bindings: i2c-stm32: document optional dmas i2c: i2c-stm32f7: Add I2C_SMBUS_I2C_BLOCK_DATA support i2c: core: Tidy up handling of init_irq i2c: core: Move ACPI gpio IRQ handling into i2c_acpi_get_irq i2c: core: Move ACPI IRQ handling to probe time i2c: acpi: Factor out getting the IRQ from ACPI i2c: acpi: Use available IRQ helper functions i2c: core: Allow whole core to use i2c_dev_irq_from_resources eeprom: at24: modify a comment referring to platform data dt-bindings: i2c: omap: Add new compatible for J721E SoCs dt-bindings: i2c: mv64xxx: Add YAML schemas dt-bindings: i2c: sun6i-p2wi: Add YAML schemas i2c: mt7621: Add MediaTek MT7621/7628/7688 I2C driver ...