| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commit has fix for RX traffic issues when we stress test the driver
with continuous ifconfig up/down under very high traffic conditions.
Reason for the issue is that, in existing liquidio_stop function NAPI is
disabled even before actual FW/HW interface is brought down via
send_rx_ctrl_cmd(lio, 0). Between time frame of NAPI disable and actual
interface down in firmware, firmware continuously enqueues rx traffic to
host. When interrupt happens for new packets, host irq handler fails in
scheduling NAPI as the NAPI is already disabled.
After "ifconfig <iface> up", Host re-enables NAPI but cannot schedule it
until it receives another Rx interrupt. Host never receives Rx interrupt as
it never cleared the Rx interrupt it received during interface down
operation. NIC Rx interrupt gets cleared only when Host processes queue and
clears the queue counts. Above anomaly leads to other issues like packet
overflow in FW/HW queues, backpressure.
Fix:
This commit fixes this issue by disabling NAPI only after informing
firmware to stop queueing packets to host via send_rx_ctrl_cmd(lio, 0).
send_rx_ctrl_cmd is not visible in the patch as it is already there in the
code. The DOWN command also waits for any pending packets to be processed
by NAPI so that the deadlock will not occur.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan-next
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2018-03-29
An update from ieee802154 for *net-next*
Colin fixed a unused variable in the new mcr20a driver.
Harry fixed an unitialised data read in the debugfs interface of the
ca8210 driver.
If there are any issues or you think these are to late for -rc1 (both can also
go into -rc2 as they are simple fixes) let me know.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In ca8210_test_int_user_write() a user can request the transfer of a
frame with a length field (command.length) that is longer than the
actual buffer provided (len). In this scenario the driver will copy
the buffer contents into the uninitialised command[] buffer, then
transfer <data.length> bytes over the SPI even though only <len> bytes
had been populated, potentially leaking sensitive kernel memory.
Also the first 6 bytes of the command buffer must be initialised in case
a malformed, short packet is written and the uninitialised bytes are
read in ca8210_test_check_upstream.
Reported-by: Domen Puncer Kugler <domen.puncer@samsung.com>
Signed-off-by: Harry Morris <h.morris@cascoda.com>
Tested-by: Harry Morris <h.morris@cascoda.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Variable 'val' is not being initialized and is later being logically
or'd with DAR_PHY_CTRL4_PROMISCUOUS. Considering this variable is never
being read anyway we may as well remove val altogether.
Cleans up error detected by cppcheck:
drivers/net/ieee802154/mcr20a.c:732: (error) Uninitialized variable: val
Fixes: 8c6ad9cc5157 ("ieee802154: Add NXP MCR20A IEEE 802.15.4 transceiver driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This adds initial suport for DWMAC5 and implements the Automotive Safety
Package which is available from core version 5.10.
The Automotive Safety Pacakge (also called Safety Features) offers us
with error protection in the core by implementing ECC Protection in
memories, on-chip data path parity protection, FSM parity and timeout
protection and Application/CSR interface timeout protection.
In case of an uncorrectable error we call stmmac_global_err() and
reconfigure the whole core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently TX Timeout handler does not behaves as expected and leads to
an unrecoverable state. Rework current implementation of TX Timeout
handling to actually perform a complete reset of the driver state and IP.
We use deferred work to init a task which will be responsible for
resetting the system.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The style of the rx/tx queue's *_coal member assignment is:
static void foo_coal_set(...)
{
set the coal in hw;
update queue's foo_coal member; [1]
}
In other place, we call foo_coal_set(pp, queue->foo_coal), so the above [1]
is duplicated and could be removed.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Call of_get_nvmem_mac_address() to fetch the MAC address from an nvmem
cell, if one is provided in the device tree. This allows the address to
be stored in an I2C EEPROM device for example.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
It's common practice to store MAC addresses for network interfaces into
nvmem devices. However the code to actually do this in the kernel lacks,
so this patch adds of_get_nvmem_mac_address() for drivers to obtain the
address from an nvmem cell provider.
This is particulary useful on devices where the ethernet interface cannot
be configured by the bootloader, for example because it's in an FPGA.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Trigger a port mod message to request an MTU change on the NIC when any
physical port representor is assigned a new MTU value. The driver waits
10 msec for an ack that the FW has set the MTU. If no ack is received the
request is rejected and an appropriate warning flagged.
Rather than maintain an MTU queue per repr, one is maintained per app.
Because the MTU ndo is protected by the rtnl lock, there can never be
contention here. Portmod messages from the NIC are also protected by
rtnl so we first check if the portmod is an ack and, if so, handle outside
rtnl and the cmsg work queue.
Acks are detected by the marking of a bit in a portmod response. They are
then verfied by checking the port number and MTU value expected by the
app. If the expected MTU is 0 then no acks are currently expected.
Also, ensure that the packet headroom reserved by the flower firmware is
considered when accepting an MTU change on any repr.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Rename the 'change_mtu' app callback to 'check_mtu'. This is called
whenever an MTU change is requested on a netdev. It can reject the
change but is not responsible for implementing it.
Introduce a new 'repr_change_mtu' app callback that is hit when the MTU
of a repr is to be changed. This is responsible for performing the MTU
change and verifying it.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Provide a pointer to the SFP bus in struct net_device, so that the
ethtool module EEPROM methods can access the SFP directly, rather
than needing every user to provide a hook for it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In preparation for having DSA transition entirely to PHYLINK, we need to pass a
PHY interface type to the mac_link_{up,down} callbacks because we may have to
make decisions on that (e.g: turn on/off RGMII interfaces etc.). We do not pass
an entire phylink_link_state because not all parameters (pause, duplex etc.) are
defined when the link is down, only link and interface are.
Update mvneta accordingly since it currently implements phylink_mac_ops.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
There were a number of issues with setting the RX coalescing parameters:
- we would not be preserving values that would have been configured
across close/open calls, instead we would always reset to no timeout
and 1 interrupt per packet, this would also prevent DIM from setting its
default usec/pkts values
- when adaptive RX would be turned on, we woud not be fetching the
default parameters, we would stay with no timeout/1 packet per interrupt
until the estimator kicks in and changes that
- finally disabling adaptive RX coalescing while providing parameters
would not be honored, and we would stay with whatever DIM had previously
determined instead of the user requested parameters
Fixes: 9f4ca05827a2 ("net: bcmgenet: Add support for adaptive RX coalescing")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
There were a number of issues with setting the RX coalescing parameters:
- we would not be preserving values that would have been configured
across close/open calls, instead we would always reset to no timeout
and 1 interrupt per packet, this would also prevent DIM from setting its
default usec/pkts values
- when adaptive RX would be turned on, we woud not be fetching the
default parameters, we would stay with no timeout/1 packet per
interrupt until the estimator kicks in and changes that
- finally disabling adaptive RX coalescing while providing parameters
would not be honored, and we would stay with whatever DIM had
previously determined instead of the user requested parameters
Fixes: b6e0e875421e ("net: systemport: Implement adaptive interrupt coalescing")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Adaptive TX coalescing is not currently giving us any advantages and
ends up making the CPU spin more frequently until TX completion. Deny
and disable adaptive TX coalescing for now and rely on static
configuration, we can always add it back later.
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fix to return a negative error code from the hash filter init error
handling case instead of 0, as done elsewhere in this function.
Fixes: 5c31254e35a8 ("cxgb4: initialize hash-filter configuration")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.17
Smaller new features to various drivers but nothing really out of
ordinary.
Major changes:
ath10k
* enable chip temperature measurement for QCA6174/QCA9377
* add firmware memory dump for QCA9984
* enable buffer STA on TDLS link for QCA6174
* support different beacon internals in multiple interface scenario
for QCA988X/QCA99X0/QCA9984/QCA4019
iwlwifi
* support for new PCI IDs for the 9000 family
* support for a new firmware API version
* support for advanced dwell and Optimized Connectivity Experience
(OCE) in scanning
btrsi
* fix kconfig dependencies
wil6210
* support multiple virtual interfaces
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
ath.git patches for 4.17. Major changes:
ath10k
* enable chip temperature measurement for QCA6174/QCA9377
* add firmware memory dump for QCA9984
* enable buffer STA on TDLS link for QCA6174
* support different beacon internals in multiple interface scenario
for QCA988X/QCA99X0/QCA9984/QCA4019
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Remove the static array and use the generic routine to set the
Ethernet broadcast address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Currently vdev stats displayed in fw_stats are applicable
only for TLV based firmware and fix it for 10.4 firmware
as of now. The vdev stats in 10.4 firmware is split into two
parts (vdev_stats, vdev_stats_extended). The actual stats
are captured only in extended vdev stats. In order to enable
vdev stats, appropriate feature bit will be set on extended
resource config. As FTM related counters are available only on
newer 10.4 based firmware, these counters will be displayed
only on valid data.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The commit "cfg80211: make RATE_INFO_BW_20 the default" changed
the index of RATE_INFO_BW_20, but the updates to ath10k missed
the special bandwidth calculation case in
ath10k_update_per_peer_tx_stats().
This will fix below warning,
WARNING: CPU: 0 PID: 609 at net/wireless/util.c:1254
cfg80211_calculate_bitrate+0x174/0x220
invalid rate bw=1, mcs=9, nss=2
(unwind_backtrace) from
(cfg80211_calculate_bitrate+0x174/0x220)
(cfg80211_calculate_bitrate) from
(nl80211_put_sta_rate+0x44/0x1dc)from
(nl80211_put_sta_rate) from
(nl80211_send_station+0x388/0xaf0)
(nl80211_get_station+0xa8/0xec)
[ end trace da8257d6a850e91a ]
Fixes: 842be75c77cb ("cfg80211: make RATE_INFO_BW_20 the default")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch fixes regression caused by 0c317a02ca98
("cfg80211: support virtual interfaces with different beacon intervals"),
with this change cfg80211 expects the driver to advertize
'beacon_int_min_gcd' to support different beacon intervals in multivap
scenario. This support is added for, QCA988X/QCA99X0/QCA9984/QCA4019.
Verifed AP + mesh bring up on QCA9984 with beacon interval 100msec and
1000msec respectively.
Frimware: firmware-5.bin_10.4-3.5.3-00053
Fixes: 0c317a02ca98 ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
For WPA encryption, QCA6174 firmware(version: WLAN.RM.4.4) will unblock
data when M4 was sent successfully. For other encryption which didn't need
4-way handshake firmware will unblock the data when peer authorized. Since
TDLS is 3-way handshake host need send authorize cmd to firmware to unblock
data.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
TDLS peer do not need WEP key. Setting WEP key will lead
to TDLS setup failure. Add fix to avoid setting WEP key
for TDLS peer.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Enable TDLS peer inactivity detetion feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS link inactivity detecting.
Set related parameters in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Enable TDLS peer buffer STA feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS peer buffer STA,
it reports this capability through wmi service map in wmi service ready
event. Set related parameter in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
In case wcn36xx_smd_rsp_process() is called more than once before
hal_ind_work was dispatched, the messages will end up in hal_ind_queue,
but wcn36xx_ind_smd_work() will only look at the first message in that
list.
Fix this by dequeing the messages from the list in a loop, and only stop
when it's empty.
This issue was found during a review of the driver. In my tests, that
race never actually occured.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
wcn36xx_start_tx function retrieves the buffer descriptor from the
channel control queue to start filling tx buffer information. However,
nothing prevents this same buffer to be concurrently accessed in a
concurent tx call, leading to potential buffer coruption and firmware
crash (observed during iperf test). The channel control queue should
only be accessed and updated with the channel lock.
Fix this issue by using a local buffer descriptor which will be copied
in the thread-safe wcn36xx_dxe_tx_frame.
Note that buffer descriptor size is few bytes so the introduced copy
overhead is insignificant. Moreover, this allows to keep the locked
section minimal.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
It appears that the WCN36xx firmware doesn't actually respond to
probe requests. Until it's resolved, switch the probe response
responsibility to the 802.11 layer to allow creation of
hidden SSID AP's.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
QCA9984/QCA99X0/QCA4019 chipsets have 8 memory regions, dump all of them to the
firmware coredump file. Some of the regions need to be read using ioread() so
add new region types for them.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[kvalo: refactoring etc]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
As QCA9984 needs two region types refactor the code to make it easier add the
new types. No functional changes.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
FW has Smart Logging feature enabled by default for detecting failures
and processing FATAL_CONDITION_EVENTID (36925 - 0x903D) back to host.
Since ath10k doesn't implement the Smart Logging and FATAL CONDITION
EVENT processing yet, suppressing the unknown event ID warning by moving
this under ATH10K_DBG_WMI.
Simulated the same issue by having associated STA powered off when
ping flood was running from AP backbone. This triggerd STA KICKOUT
in AP followed by FATAL CONDITION event 36925.
Issue was reproduced and verified in below DUT
------------------------------------------------
AP mode of OpenWRT QCA9984 running 6.0.8 with FW ver 10.4-3.5.3-00053
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Firmware WLAN.TF.2.1-00014-QCARMSWP-1 now supports reading the board ID
information and also required 9 IRAM bank, which older ath10k version
don't have the support will fail to be enabled, so in order to maintain
the backward compatibility, we need to update the FW API to 6.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The firmware of QCA6174/QCA9377 already support the feature, just enable
it to be able to handle the get_temperature command and process the event.
You can read the temperature by using the hwmon interface,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Verified with the following hardware and software combination,
QCA6174, only firmware-4.bin doesn't support this, otherwise all support.
QCA9377, all the firmwares upstreamed support this command
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This reverts commit 55884c045d31a29cf69db8332d1064a1b61dd159.
When Ath10k is in AP mode and an unassociated STA sends a VHT action frame
(Operating Mode Notification for the NSS change) periodically to AP this causes
ath10k to call ath10k_station_assoc() which sends WMI_PEER_ASSOC_CMDID during
NSS update. Over the time (with a certain client it can happen within 15 mins
when there are over 500 of these VHT action frames) continuous calls of
WMI_PEER_ASSOC_CMDID cause firmware to assert due to resource exhaust.
To my knowledge setting WMI_PEER_NSS peer param itself enough to handle NSS
updates and no need to call ath10k_station_assoc(). So revert the original
commit from 2014 as it's unclear why the change was really needed.
Now the firmware assert doesn't happen anymore.
Issue observed in QCA9984 platform with firmware version:10.4-3.5.3-00053.
This Change tested in QCA9984 with firmware version: 10.4-3.5.3-00053 and
QCA988x platform with firmware version: 10.2.4-1.0-00036.
Firmware Assert log:
ath10k_pci 0002:01:00.0: firmware crashed! (guid e61f1274-9acd-4c5b-bcca-e032ea6e723c)
ath10k_pci 0002:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
ath10k_pci 0002:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 1 testmode 1
ath10k_pci 0002:01:00.0: firmware ver 10.4-3.5.3-00053 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast crc32 4c56a386
ath10k_pci 0002:01:00.0: board_file api 2 bmi_id 0:4 crc32 c2271344
ath10k_pci 0002:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
ath10k_pci 0002:01:00.0: firmware register dump:
ath10k_pci 0002:01:00.0: [00]: 0x0000000A 0x000015B3 0x00981E5F 0x00975B31
ath10k_pci 0002:01:00.0: [04]: 0x00981E5F 0x00060530 0x00000011 0x00446C60
ath10k_pci 0002:01:00.0: [08]: 0x0042F1FC 0x00458080 0x00000017 0x00000000
ath10k_pci 0002:01:00.0: [12]: 0x00000009 0x00000000 0x00973ABC 0x00973AD2
ath10k_pci 0002:01:00.0: [16]: 0x00973AB0 0x00960E62 0x009606CA 0x00000000
ath10k_pci 0002:01:00.0: [20]: 0x40981E5F 0x004066DC 0x00400000 0x00981E34
ath10k_pci 0002:01:00.0: [24]: 0x80983B48 0x0040673C 0x000000C0 0xC0981E5F
ath10k_pci 0002:01:00.0: [28]: 0x80993DEB 0x0040676C 0x00431AB8 0x0045D0C4
ath10k_pci 0002:01:00.0: [32]: 0x80993E5C 0x004067AC 0x004303C0 0x0045D0C4
ath10k_pci 0002:01:00.0: [36]: 0x80994AAB 0x004067DC 0x00000000 0x0045D0C4
ath10k_pci 0002:01:00.0: [40]: 0x809971A0 0x0040681C 0x004303C0 0x00441B00
ath10k_pci 0002:01:00.0: [44]: 0x80991904 0x0040688C 0x004303C0 0x0045D0C4
ath10k_pci 0002:01:00.0: [48]: 0x80963AD3 0x00406A7C 0x004303C0 0x009918FC
ath10k_pci 0002:01:00.0: [52]: 0x80960E80 0x00406A9C 0x0000001F 0x00400000
ath10k_pci 0002:01:00.0: [56]: 0x80960E51 0x00406ACC 0x00400000 0x00000000
ath10k_pci 0002:01:00.0: Copy Engine register dump:
ath10k_pci 0002:01:00.0: index: addr: sr_wr_idx: sr_r_idx: dst_wr_idx: dst_r_idx:
ath10k_pci 0002:01:00.0: [00]: 0x0004a000 15 15 3 3
ath10k_pci 0002:01:00.0: [01]: 0x0004a400 17 17 212 213
ath10k_pci 0002:01:00.0: [02]: 0x0004a800 21 21 20 21
ath10k_pci 0002:01:00.0: [03]: 0x0004ac00 25 25 27 25
ath10k_pci 0002:01:00.0: [04]: 0x0004b000 515 515 144 104
ath10k_pci 0002:01:00.0: [05]: 0x0004b400 28 28 155 156
ath10k_pci 0002:01:00.0: [06]: 0x0004b800 12 12 12 12
ath10k_pci 0002:01:00.0: [07]: 0x0004bc00 1 1 1 1
ath10k_pci 0002:01:00.0: [08]: 0x0004c000 0 0 127 0
ath10k_pci 0002:01:00.0: [09]: 0x0004c400 1 1 1 1
ath10k_pci 0002:01:00.0: [10]: 0x0004c800 0 0 0 0
ath10k_pci 0002:01:00.0: [11]: 0x0004cc00 0 0 0 0
ath10k_pci 0002:01:00.0: CE[1] write_index 212 sw_index 213 hw_index 0 nentries_mask 0x000001ff
ath10k_pci 0002:01:00.0: CE[2] write_index 20 sw_index 21 hw_index 0 nentries_mask 0x0000007f
ath10k_pci 0002:01:00.0: CE[5] write_index 155 sw_index 156 hw_index 0 nentries_mask 0x000001ff
ath10k_pci 0002:01:00.0: DMA addr: nbytes: meta data: byte swap: gather:
ath10k_pci 0002:01:00.0: [455]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [456]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [457]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [458]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [459]: 0x580c0a42 0 0 0 0
ath10k_pci 0002:01:00.0: [460]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [461]: 0x580c0c42 0 0 0 0
ath10k_pci 0002:01:00.0: [462]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [463]: 0x580c0c42 0 0 0 0
ath10k_pci 0002:01:00.0: [464]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [465]: 0x580c0a42 0 0 0 0
ath10k_pci 0002:01:00.0: [466]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [467]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [468]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [469]: 0x580c1c42 0 0 0 0
ath10k_pci 0002:01:00.0: [470]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [471]: 0x580c1c42 0 0 0 0
ath10k_pci 0002:01:00.0: [472]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [473]: 0x580c1c42 0 0 0 0
ath10k_pci 0002:01:00.0: [474]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [475]: 0x580c0642 0 0 0 0
ath10k_pci 0002:01:00.0: [476]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [477]: 0x580c0842 0 0 0 0
ath10k_pci 0002:01:00.0: [478]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [479]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [480]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [481]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [482]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [483]: 0x580c0842 0 0 0 0
ath10k_pci 0002:01:00.0: [484]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [485]: 0x580c0642 0 0 0 0
ath10k_pci 0002:01:00.0: [486]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [487]: 0x580c0642 0 0 0 0
ath10k_pci 0002:01:00.0: [488]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [489]: 0x580c0842 0 0 0 0
ath10k_pci 0002:01:00.0: [490]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [491]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [492]: 0x58174040 0 1 0 0
ath10k_pci 0002:01:00.0: [493]: 0x5a946040 0 1 0 0
ath10k_pci 0002:01:00.0: [494]: 0x59909040 0 1 0 0
ath10k_pci 0002:01:00.0: [495]: 0x5ae5a040 0 1 0 0
ath10k_pci 0002:01:00.0: [496]: 0x58096040 0 1 0 0
ath10k_pci 0002:01:00.0: [497]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [498]: 0x580c0642 0 0 0 0
ath10k_pci 0002:01:00.0: [499]: 0x5c1e0040 0 1 0 0
ath10k_pci 0002:01:00.0: [500]: 0x58153040 0 1 0 0
ath10k_pci 0002:01:00.0: [501]: 0x58129040 0 1 0 0
ath10k_pci 0002:01:00.0: [502]: 0x5952f040 0 1 0 0
ath10k_pci 0002:01:00.0: [503]: 0x59535040 0 1 0 0
ath10k_pci 0002:01:00.0: [504]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [505]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [506]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [507]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [508]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [509]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [510]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [511]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [512]: 0x5adcc040 0 1 0 0
ath10k_pci 0002:01:00.0: [513]: 0x5cf3d040 0 1 0 0
ath10k_pci 0002:01:00.0: [514]: 0x5c1e9040 64 1 0 0
ath10k_pci 0002:01:00.0: [515]: 0x00000000 0 0 0 0
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
some userspace programs (e.g. hostapd) need to set the regulatory domain
before selecting the operating channel. Synchronize DFS detector regardless of
the value of ah->curchan, to avoid situations where wireless scan can't be done
on some 5GHz sub-bands, because dfs_region is constantly UNSET.
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Timothy Redaelli <tredaelli@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We can set triggers that cause a debug data collection when something
of interest happens (e.g. when too many probes are lost conscutively).
Normally, this triggers don't cause the FW to be restarted, but in
some cases that may be desired, so we recover from the problem. To
support this, add a flag that indicates that the FW should be
restarted when the trigger fires.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Currently we have a boolean variable for each cause.
This costs space, and requires to check each separately
when determining low latency.
Since we have another cause incoming, convert it to an enum.
While at it, move the retrieval of the prev value and the
assignment of the new value to be inside iwl_mvm_update_low_latency
and save the need for each caller to do it separately.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We are now ready to load 38.ucode
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Some geographic profiles require specific handling. For example ETSI
profile requires special channel access handling. Add geographic
profile information to MCC_UPDATE response to allow it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
A lot of new PCI IDs were added for the 9000 series. Add them to the
list of supported PCI IDs.
Cc: stable@vger.kernel.org # 4.13+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Remove fragmented_dwell_time and add num_of_fragments to support
the new API version.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The FW does not allocate quota air time for the binding of a station
MAC before iwlmvm indicates that it is associated. Currently iwlmvm
indicates that the MAC is associated only after hearing a beacon from
the AP. In case a deauthentication frame is sent before the MAC is
associated, the frame might not be sent as the corresponding binding
is not scheduled.
To handle such cases, set IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP in the
HW flags, requesting mac80211 to call the mgd_prepare_tx() callback
before transmitting a deauthentication frame if associated but no
beacon was heard from the AP.
In addition, do not warn in iwl_mvm_mac_mgd_prepare_tx() when already
associated as now the callback can be called also when associated.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add support for Optimized Connectivity Experience (OCE). Get
capabilities from the fw, expose them with nl80211, and enable them in
UMAC scan if the relevant nl80211 flags are set by the userspace.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Update the scan command API with support for adaptive dwell. Adaptive
dwell is a type of scan that dynamically changes the time it remains
on each channel listening for beacons or probe responses.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Sometimes iwl_mvm_disable_txq() may be called with mac80211_queue ==
IEEE80211_INVAL_HW_QUEUE, and this would cause us to use BIT(0xFF)
which is way too large for the u16 we used to store it in
hw_queue_to_mac820211. If this happens the following UBSAN warning
will be generated:
[ 167.185167] UBSAN: Undefined behaviour in drivers/net/wireless/intel/iwlwifi/mvm/utils.c:838:5
[ 167.185171] shift exponent 255 is too large for 64-bit type 'long unsigned int'
Fix that by checking that it is not IEEE80211_INVAL_HW_QUEUE and,
while at it, add a warning if the queue number is larger than
IEEE80211_MAX_QUEUES.
Fixes: 34e10860ae8d ("iwlwifi: mvm: remove references to queue_info in new TX path")
Reported-by: Paul Menzel <pmenzel+linux-wireless@molgen.mpg.de>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
In case debug configuration is started with LDBG cmd also start timestamp
marker for syncing logs witn the FW.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This makes future bail-outs from transmitting an AMSDU more
readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
RCU isn't properly locked.
Fixes: 46d372af9935 ("iwlwifi: mvm: rs: new rate scale API - add FW notifications")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|