| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The dummycon default console size used to be determined by architecture,
but now this is a Kconfig setting on everything except ARM. Tracing this
back in the historic git trees, this was used to match the size of VGA
console or VGA framebuffer on early machines, but nowadays that code is
no longer used, except probably on the old footbridge/netwinder since
that is the only one that supports vgacon.
On machines with a framebuffer, booting with DT so far results in always
using the hardcoded 80x30 size in dummycon, while on ATAGS the setting
can come from a bootloader specific override. Both seem to be worse
choices than the Kconfig setting, since the actual text size for fbcon
also depends on the selected font.
Make this work the same way as everywhere else and use the normal
Kconfig setting, except for the footbridge with vgacon, which keeps
using the traditional code. If vgacon is disabled, footbridge can
also ignore the setting. This means the screen_info only has to be
provided when either vgacon or EFI are enabled now.
To limit the amount of surprises on Arm, change the Kconfig default
to the previously used 80x30 setting instead of the usual 80x25.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231009211845.3136536-4-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The list of dependencies here is phrased as an opt-out, but this is missing
a lot of architectures that don't actually support VGA consoles, and some
of the entries are stale:
- powerpc used to support VGA consoles in the old arch/ppc codebase, but
the merged arch/powerpc never did
- arm lists footbridge, integrator and netwinder, but netwinder is actually
part of footbridge, and integrator does not appear to have an actual
VGA hardware, or list it in its ATAG or DT.
- mips has a few platforms (malta, sibyte, and sni) that initialize
screen_info, on everything else the console is selected but cannot
actually work.
- csky, hexgagon, loongarch, nios2, riscv and xtensa are not listed
in the opt-out table and declare a screen_info to allow building
vga_con, but this cannot work because the console is never selected.
Replace this with an opt-in table that lists only the platforms that
remain. This is effectively x86, plus a couple of historic workstation
and server machines that reused parts of the x86 system architecture.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Khalid Aziz <khalid@gonehiking.org>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20231009211845.3136536-2-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There might be hard lockup if we set crtscts mode on port without RTS/CTS configured:
# stty -F /dev/ttyAML6 crtscts; echo 1 > /dev/ttyAML6; echo 2 > /dev/ttyAML6
[ 95.890386] rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
[ 95.890857] rcu: 3-...0: (201 ticks this GP) idle=e33c/1/0x4000000000000000 softirq=5844/5846 fqs=4984
[ 95.900212] rcu: (detected by 2, t=21016 jiffies, g=7753, q=296 ncpus=4)
[ 95.906972] Task dump for CPU 3:
[ 95.910178] task:bash state:R running task stack:0 pid:205 ppid:1 flags:0x00000202
[ 95.920059] Call trace:
[ 95.922485] __switch_to+0xe4/0x168
[ 95.925951] 0xffffff8003477508
[ 95.974379] watchdog: Watchdog detected hard LOCKUP on cpu 3
[ 95.974424] Modules linked in: 88x2cs(O) rtc_meson_vrtc
Possible solution would be to not allow to setup crtscts on such port.
Tested on S905X3 based board.
Fixes: ff7693d079e5 ("ARM: meson: serial: add MesonX SoC on-chip uart driver")
Cc: stable@vger.kernel.org
Signed-off-by: Pavel Krasavin <pkrasavin@imaqliq.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
v6: stable tag added
v5: https://lore.kernel.org/lkml/OF43DA36FF.2BD3BB21-ON00258A47.005A8125-00258A47.005A9513@gdc.ru/
added missed Reviewed-by tags, Fixes tag added according to Dmitry and Neil notes
v4: https://lore.kernel.org/lkml/OF55521400.7512350F-ON00258A47.003F7254-00258A47.0040E15C@gdc.ru/
More correct patch subject according to Jiri's note
v3: https://lore.kernel.org/lkml/OF6CF5FFA0.CCFD0E8E-ON00258A46.00549EDF-00258A46.0054BB62@gdc.ru/
"From:" line added to the mail
v2: https://lore.kernel.org/lkml/OF950BEF72.7F425944-ON00258A46.00488A76-00258A46.00497D44@gdc.ru/
braces for single statement removed according to Dmitry's note
v1: https://lore.kernel.org/lkml/OF28B2B8C9.5BC0CD28-ON00258A46.0037688F-00258A46.0039155B@gdc.ru/
Link: https://lore.kernel.org/r/OF66360032.51C36182-ON00258A48.003F656B-00258A48.0040092C@gdc.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Add driver for the ACM gadget controller of the Espressif ESP32S3 SoC.
Hardware specification is available at the following URL:
https://www.espressif.com/sites/default/files/documentation/esp32-s3_technical_reference_manual_en.pdf
(Chapter 33 USB Serial/JTAG Controller)
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20231010085926.1021667-6-jcmvbkbc@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add driver for the UART controllers of the Espressif ESP32 and ESP32S3
SoCs. Hardware specification is available at the following URLs:
https://www.espressif.com/sites/default/files/documentation/esp32_technical_reference_manual_en.pdf
(Chapter 13 UART Controller)
https://www.espressif.com/sites/default/files/documentation/esp32-s3_technical_reference_manual_en.pdf
(Chapter 26 UART Controller)
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20231010085926.1021667-4-jcmvbkbc@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
uart_get_baud_rate has input parameters 'min' and 'max' limiting the
range of acceptable baud rates from the caller's perspective. If neither
current or old termios structures have acceptable baud rate setting and
9600 is not in the min/max range either the function returns 0 and
issues a warning.
However for a UART that does not support speed of 9600 baud this is
expected behavior.
Clarify that 0 can be (and always could be) returned from the
uart_get_baud_rate. Don't issue a warning in that case.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20231010085926.1021667-2-jcmvbkbc@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
Zynq UG585 states, in chapter B.33, for XUARTPS_CR_STARTBRK:
It can only be set if STPBRK (Stop transmitter break) is not high
This fixes tcsendbreak, which otherwise does not actually break.
Signed-Off-By: Julien Malik <julien.malik@unseenlabs.fr>
Link: https://lore.kernel.org/r/20230624210323.88455-1-julien.malik@unseenlabs.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
| |
Fix coding style. No functional changes.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231011130317.3562401-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We need the tty/serial fixes in here as well for testing, and this
resolves merge conflicts in:
drivers/tty/serial/serial_core.c
as reported in linux-next
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit 295525e29a5b ("virtio_net: merge dma operations when filling
mergeable buffers") unmaps the buffer with DMA_ATTR_SKIP_CPU_SYNC when
the dma->ref is zero. We do that with DMA_ATTR_SKIP_CPU_SYNC, because we
do not want to do the sync for the entire page_frag. But that misses the
sync for the current area.
This patch does cpu sync regardless of whether the ref is zero or not.
Fixes: 295525e29a5b ("virtio_net: merge dma operations when filling mergeable buffers")
Reported-by: Michael Roth <michael.roth@amd.com>
Closes: http://lore.kernel.org/all/20230926130451.axgodaa6tvwqs3ut@amd.com
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt fixes from Greg KH:
"Here are some USB and Thunderbolt driver fixes for 6.6-rc6 to resolve
a number of small reported issues. Included in here are:
- thunderbolt driver fixes
- xhci driver fixes
- cdns3 driver fixes
- musb driver fixes
- a number of typec driver fixes
- a few other small driver fixes
All of these have been in linux-next with no reported issues"
* tag 'usb-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
usb: typec: ucsi: Use GET_CAPABILITY attributes data to set power supply scope
usb: typec: ucsi: Fix missing link removal
usb: typec: altmodes/displayport: Signal hpd low when exiting mode
xhci: Preserve RsvdP bits in ERSTBA register correctly
xhci: Clear EHB bit only at end of interrupt handler
xhci: track port suspend state correctly in unsuccessful resume cases
usb: xhci: xhci-ring: Use sysdev for mapping bounce buffer
usb: typec: ucsi: Clear EVENT_PENDING bit if ucsi_send_command fails
usb: misc: onboard_hub: add support for Microchip USB2412 USB 2.0 hub
usb: gadget: udc-xilinx: replace memcpy with memcpy_toio
usb: cdns3: Modify the return value of cdns_set_active () to void when CONFIG_PM_SLEEP is disabled
usb: dwc3: Soft reset phy on probe for host
usb: hub: Guard against accesses to uninitialized BOS descriptors
usb: typec: qcom: Update the logic of regulator enable and disable
usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call
usb: musb: Get the musb_qh poniter after musb_giveback
usb: musb: Modify the "HWVers" register address
usb: cdnsp: Fixes issue with dequeuing not queued requests
thunderbolt: Restart XDomain discovery handshake after failure
thunderbolt: Correct TMU mode initialization from hardware
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
On some OEM systems, adding a W7900 dGPU triggers RAS errors and hangs
at a black screen on startup. This issue occurs only if `ucsi_acpi` has
loaded before `amdgpu` has loaded. The reason for this failure is that
`amdgpu` uses power_supply_is_system_supplied() to determine if running
on AC or DC power at startup. If this value is reported incorrectly the
dGPU will also be programmed incorrectly and trigger errors.
power_supply_is_system_supplied() reports the wrong value because UCSI
power supplies provided as part of the system don't properly report the
scope as "DEVICE" scope (not powering the system).
In order to fix this issue check the capabilities reported from the UCSI
power supply to ensure that it supports charging a battery and that it can
be powered by AC. Mark the scope accordingly.
Cc: stable@vger.kernel.org
Fixes: a7fbfd44c020 ("usb: typec: ucsi: Mark dGPUs as DEVICE scope")
Link: https://www.intel.com/content/www/us/en/products/docs/io/universal-serial-bus/usb-type-c-ucsi-spec.html p28
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231009184643.129986-1-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The link between the partner device and its USB Power
Delivery instance was never removed which prevented the
device from being released. Removing the link always when
the partner is unregistered.
Fixes: b04e1747fbcc ("usb: typec: ucsi: Register USB Power Delivery Capabilities")
Cc: stable <stable@kernel.org>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Closes: https://lore.kernel.org/linux-usb/ZSUMXdw9nanHtnw2@kuha.fi.intel.com/
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231010141749.3912016-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Upon receiving an ACK for a sent EXIT_MODE message, the DisplayPort
driver currently resets the status and configuration of the port partner.
The hpd signal is not updated despite being part of the status, so the
Display stack can still transmit video despite typec_altmode_exit placing
the lanes in a Safe State.
Set hpd to low when a sent EXIT_MODE message is ACK'ed.
Fixes: 0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231009210057.3773877-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
xhci_add_interrupter() erroneously preserves only the lowest 4 bits when
writing the ERSTBA register, not the lowest 6 bits. Fix it.
Migrate the ERST_BASE_RSVDP macro to the modern GENMASK_ULL() syntax to
avoid a u64 cast.
This was previously fixed by commit 8c1cbec9db1a ("xhci: fix event ring
segment table related masks and variables in header"), but immediately
undone by commit b17a57f89f69 ("xhci: Refactor interrupter code for
initial multi interrupter support.").
Fixes: b17a57f89f69 ("xhci: Refactor interrupter code for initial multi interrupter support.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.3+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The Event Handler Busy bit shall be cleared by software when the Event
Ring is empty. The xHC is thereby informed that it may raise another
interrupt once it has enqueued new events (sec 4.17.2).
However since commit dc0ffbea5729 ("usb: host: xhci: update event ring
dequeue pointer on purpose"), the EHB bit is already cleared after half
a segment has been processed.
As a result, spurious interrupts may occur:
- xhci_irq() processes half a segment, clears EHB, continues processing
remaining events.
- xHC enqueues new events. Because EHB has been cleared, xHC sets
Interrupt Pending bit. Interrupt moderation countdown begins.
- Meanwhile xhci_irq() continues processing events. Interrupt
moderation countdown reaches zero, so an MSI interrupt is signaled.
- xhci_irq() empties the Event Ring, clears EHB again and is done.
- Because an MSI interrupt has been signaled, xhci_irq() is run again.
It discovers there's nothing to do and returns IRQ_NONE.
Avoid by clearing the EHB bit only at the end of xhci_irq().
Fixes: dc0ffbea5729 ("usb: host: xhci: update event ring dequeue pointer on purpose")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v5.5+
Cc: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
xhci-hub.c tracks suspended ports in a suspended_port bitfield.
This is checked when responding to a Get_Status(PORT) request to see if a
port in running U0 state was recently resumed, and adds the required
USB_PORT_STAT_C_SUSPEND change bit in those cases.
The suspended_port bit was left uncleared if a device is disconnected
during suspend. The bit remained set even when a new device was connected
and enumerated. The set bit resulted in a incorrect Get_Status(PORT)
response with a bogus USB_PORT_STAT_C_SUSPEND change
bit set once the new device reached U0 link state.
USB_PORT_STAT_C_SUSPEND change bit is only used for USB2 ports, but
xhci-hub keeps track of both USB2 and USB3 suspended ports.
Cc: stable@vger.kernel.org
Reported-by: Wesley Cheng <quic_wcheng@quicinc.com>
Closes: https://lore.kernel.org/linux-usb/d68aa806-b26a-0e43-42fb-b8067325e967@quicinc.com/
Fixes: 1d5810b6923c ("xhci: Rework port suspend structures for limited ports.")
Tested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
As mentioned in:
commit 474ed23a6257 ("xhci: align the last trb before link if it is
easily splittable.")
A bounce buffer is utilized for ensuring that transfers that span across
ring segments are aligned to the EP's max packet size. However, the device
that is used to map the DMA buffer to is currently using the XHCI HCD,
which does not carry any DMA operations in certain configrations.
Migration to using the sysdev entry was introduced for DWC3 based
implementations where the IOMMU operations are present.
Replace the reference to the controller device to sysdev instead. This
allows the bounce buffer to be properly mapped to any implementations that
have an IOMMU involved.
cc: stable@vger.kernel.org
Fixes: 4c39d4b949d3 ("usb: xhci: use bus->sysdev for DMA configuration")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Currently if ucsi_send_command() fails, then we bail out without
clearing EVENT_PENDING flag. So when the next connector change
event comes, ucsi_connector_change() won't queue the con->work,
because of which none of the new events will be processed.
Fix this by clearing EVENT_PENDING flag if ucsi_send_command()
fails.
Cc: stable@vger.kernel.org # 5.16
Fixes: 512df95b9432 ("usb: typec: ucsi: Better fix for missing unplug events issue")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/1694423055-8440-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The USB2412 is a 2-Port USB 2.0 hub controller that provides a reset pin
and a single 3v3 powre source, which makes it suitable to be controlled
by the onboard_hub driver.
This hub has the same reset timings as USB2514/2517 and the same
onboard hub specific-data can be reused for USB2412.
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Cc: stable <stable@kernel.org>
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20230911-topic-2412_onboard_hub-v1-1-7704181ddfff@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
For ARM processor, unaligned access to device memory is not allowed.
Method memcpy does not take care of alignment.
USB detection failure with the unalingned address of memory, with
below kernel crash. To fix the unalingned address kernel panic,
replace memcpy with memcpy_toio method.
Kernel crash:
Unable to handle kernel paging request at virtual address ffff80000c05008a
Mem abort info:
ESR = 0x96000061
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x21: alignment fault
Data abort info:
ISV = 0, ISS = 0x00000061
CM = 0, WnR = 1
swapper pgtable: 4k pages, 48-bit VAs, pgdp=000000000143b000
[ffff80000c05008a] pgd=100000087ffff003, p4d=100000087ffff003,
pud=100000087fffe003, pmd=1000000800bcc003, pte=00680000a0010713
Internal error: Oops: 96000061 [#1] SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.15.19-xilinx-v2022.1 #1
Hardware name: ZynqMP ZCU102 Rev1.0 (DT)
pstate: 200000c5 (nzCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __memcpy+0x30/0x260
lr : __xudc_ep0_queue+0xf0/0x110
sp : ffff800008003d00
x29: ffff800008003d00 x28: ffff800009474e80 x27: 00000000000000a0
x26: 0000000000000100 x25: 0000000000000012 x24: ffff000800bc8080
x23: 0000000000000001 x22: 0000000000000012 x21: ffff000800bc8080
x20: 0000000000000012 x19: ffff000800bc8080 x18: 0000000000000000
x17: ffff800876482000 x16: ffff800008004000 x15: 0000000000004000
x14: 00001f09785d0400 x13: 0103020101005567 x12: 0781400000000200
x11: 00000000c5672a10 x10: 00000000000008d0 x9 : ffff800009463cf0
x8 : ffff8000094757b0 x7 : 0201010055670781 x6 : 4000000002000112
x5 : ffff80000c05009a x4 : ffff000800a15012 x3 : ffff00080362ad80
x2 : 0000000000000012 x1 : ffff000800a15000 x0 : ffff80000c050088
Call trace:
__memcpy+0x30/0x260
xudc_ep0_queue+0x3c/0x60
usb_ep_queue+0x38/0x44
composite_ep0_queue.constprop.0+0x2c/0xc0
composite_setup+0x8d0/0x185c
configfs_composite_setup+0x74/0xb0
xudc_irq+0x570/0xa40
__handle_irq_event_percpu+0x58/0x170
handle_irq_event+0x60/0x120
handle_fasteoi_irq+0xc0/0x220
handle_domain_irq+0x60/0x90
gic_handle_irq+0x74/0xa0
call_on_irq_stack+0x2c/0x60
do_interrupt_handler+0x54/0x60
el1_interrupt+0x30/0x50
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x78/0x7c
arch_cpu_idle+0x18/0x2c
do_idle+0xdc/0x15c
cpu_startup_entry+0x28/0x60
rest_init+0xc8/0xe0
arch_call_rest_init+0x10/0x1c
start_kernel+0x694/0x6d4
__primary_switched+0xa4/0xac
Fixes: 1f7c51660034 ("usb: gadget: Add xilinx usb2 device support")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/all/202209020044.CX2PfZzM-lkp@intel.com/
Cc: stable@vger.kernel.org
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20230929121514.13475-1-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
CONFIG_PM_SLEEP is disabled
The return type of cdns_set_active () is inconsistent
depending on whether CONFIG_PM_SLEEP is enabled, so the
return value is modified to void type.
Reported-by: Pavel Machek <pavel@denx.de>
Closes: https://lore.kernel.org/all/ZP7lIKUzD68XA91j@duo.ucw.cz/
Fixes: 2319b9c87fe2 ("usb: cdns3: Put the cdns set active part outside the spin lock")
Cc: stable@vger.kernel.org
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230926075333.1791011-1-xiaolei.wang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When there's phy initialization, we need to initiate a soft-reset
sequence. That's done through USBCMD.HCRST in the xHCI driver and its
initialization, However, the dwc3 driver may modify core configs before
the soft-reset. This may result in some connection instability. So,
ensure the phy is ready before the controller updates the GCTL.PRTCAPDIR
or other settings by issuing phy soft-reset.
Note that some host-mode configurations may not expose device registers
to initiate the controller soft-reset (via DCTL.CoreSftRst). So we reset
through GUSB3PIPECTL and GUSB2PHYCFG instead.
Cc: stable@vger.kernel.org
Fixes: e835c0a4e23c ("usb: dwc3: don't reset device side if dwc3 was configured as host-only")
Reported-by: Kenta Sato <tosainu.maple@gmail.com>
Closes: https://lore.kernel.org/linux-usb/ZPUciRLUcjDywMVS@debian.me/
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Kenta Sato <tosainu.maple@gmail.com>
Link: https://lore.kernel.org/r/70aea513215d273669152696cc02b20ddcdb6f1a.1694564261.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Many functions in drivers/usb/core/hub.c and drivers/usb/core/hub.h
access fields inside udev->bos without checking if it was allocated and
initialized. If usb_get_bos_descriptor() fails for whatever
reason, udev->bos will be NULL and those accesses will result in a
crash:
BUG: kernel NULL pointer dereference, address: 0000000000000018
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 5 PID: 17818 Comm: kworker/5:1 Tainted: G W 5.15.108-18910-gab0e1cb584e1 #1 <HASH:1f9e 1>
Hardware name: Google Kindred/Kindred, BIOS Google_Kindred.12672.413.0 02/03/2021
Workqueue: usb_hub_wq hub_event
RIP: 0010:hub_port_reset+0x193/0x788
Code: 89 f7 e8 20 f7 15 00 48 8b 43 08 80 b8 96 03 00 00 03 75 36 0f b7 88 92 03 00 00 81 f9 10 03 00 00 72 27 48 8b 80 a8 03 00 00 <48> 83 78 18 00 74 19 48 89 df 48 8b 75 b0 ba 02 00 00 00 4c 89 e9
RSP: 0018:ffffab740c53fcf8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffffa1bc5f678000 RCX: 0000000000000310
RDX: fffffffffffffdff RSI: 0000000000000286 RDI: ffffa1be9655b840
RBP: ffffab740c53fd70 R08: 00001b7d5edaa20c R09: ffffffffb005e060
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: ffffab740c53fd3e R14: 0000000000000032 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffffa1be96540000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000018 CR3: 000000022e80c005 CR4: 00000000003706e0
Call Trace:
hub_event+0x73f/0x156e
? hub_activate+0x5b7/0x68f
process_one_work+0x1a2/0x487
worker_thread+0x11a/0x288
kthread+0x13a/0x152
? process_one_work+0x487/0x487
? kthread_associate_blkcg+0x70/0x70
ret_from_fork+0x1f/0x30
Fall back to a default behavior if the BOS descriptor isn't accessible
and skip all the functionalities that depend on it: LPM support checks,
Super Speed capabilitiy checks, U1/U2 states setup.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230830100418.1952143-1-ricardo.canuelo@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Removed the call logic of disable and enable regulator
in reset function. Enable the regulator in qcom_pmic_typec_start
function and disable it in qcom_pmic_typec_stop function to
avoid unbalanced regulator disable warnings.
Fixes: a4422ff22142 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # rb5
Signed-off-by: Hui Liu <quic_huliu@quicinc.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230831-qcom-tcpc-v5-1-5e2661dc6c1d@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When NCM is used with hosts like Windows PC, it is observed that there are
multiple NTB's contained in one usb request giveback. Since the driver
unwraps the obtained request data assuming only one NTB is present, we
loose the subsequent NTB's present resulting in data loss.
Fix this by checking the parsed block length with the obtained data
length in usb request and continue parsing after the last byte of current
NTB.
Cc: stable@vger.kernel.org
Fixes: 9f6ce4240a2b ("usb: gadget: f_ncm.c added")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20230927105858.12950-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When multiple threads are performing USB transmission, musb->lock will be
unlocked when musb_giveback is executed. At this time, qh may be released
in the dequeue process in other threads, resulting in a wild pointer, so
it needs to be here get qh again, and judge whether qh is NULL, and when
dequeue, you need to set qh to NULL.
Fixes: dbac5d07d13e ("usb: musb: host: don't start next rx urb if current one failed")
Cc: stable@vger.kernel.org
Signed-off-by: Xingxing Luo <xingxing.luo@unisoc.com>
Link: https://lore.kernel.org/r/20230919033055.14085-1-xingxing.luo@unisoc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
musb HWVers rgister address is not 0x69, if we operate the
wrong address 0x69, it will cause a kernel crash, because
there is no register corresponding to this address in the
additional control register of musb. In fact, HWVers has
been defined in musb_register.h, and the name is
"MUSB_HWVERS", so We need to use this macro instead of 0x69.
Fixes: c2365ce5d5a0 ("usb: musb: replace hard coded registers with defines")
Cc: stable@vger.kernel.org
Signed-off-by: Xingxing Luo <xingxing.luo@unisoc.com>
Link: https://lore.kernel.org/r/20230922075929.31074-1-xingxing.luo@unisoc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Gadget ACM while unloading module try to dequeue not queued usb
request which causes the kernel to crash.
Patch adds extra condition to check whether usb request is processed
by CDNSP driver.
cc: stable@vger.kernel.org
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230713081429.326660-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |\
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
thunderbolt: Fixes for v6.6-rc3
This includes following fixes for v6.6-rc3:
- Add a workaround for IOMMU faults for certain systems with Intel
Maple Ridge
- Make sure lane 1 is in CL0 before bonding lanes
- Correct TMU mode initialization from hardware
- Restart XDomain discovery handshake after failure.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Restart XDomain discovery handshake after failure
thunderbolt: Correct TMU mode initialization from hardware
thunderbolt: Check that lane 1 is in CL0 before enabling lane bonding
thunderbolt: Workaround an IOMMU fault on certain systems with Intel Maple Ridge
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Alex reported that after rebooting the other host the peer-to-peer link
does not come up anymore. The reason for this is that the host that was
not rebooted tries to send the UUID request only 10 times according to
the USB4 Inter-Domain spec and gives up if it does not get reply. Then
when the other side is actually ready it cannot get the link established
anymore. The USB4 Inter-Domain spec requires that the discovery protocol
is restarted in that case so implement this now.
Reported-by: Alex Balcanquall <alex@alexbal.com>
Fixes: 8e1de7042596 ("thunderbolt: Add support for XDomain lane bonding")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
David reported that cppcheck found following possible copy & paste
error from tmu_mode_init():
tmu.c:385:50: style: Expression is always false because 'else if' condition matches previous condition at line 383. [multiCondition]
And indeed this is a bug. Fix it to use correct index
(TB_SWITCH_TMU_MODE_HIFI_UNI).
Reported-by: David Binderman <dcb314@hotmail.com>
Fixes: d49b4f043d63 ("thunderbolt: Add support for enhanced uni-directional TMU mode")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Marek reported that when BlackMagic UltraStudio device is connected the
kernel repeatedly tries to enable lane bonding without success making
the device non-functional. It looks like the device does not have lane 1
connected at all so even though it is enabled we should not try to bond
the lanes. For this reason check that lane 1 is in fact CL0 (connected,
active) before attempting to bond the lanes.
Reported-by: Marek Šanta <teslan223@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217737
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
On some systems the IOMMU blocks the first couple of driver ready
messages to the connection manager firmware as can be seen in below
excerpts:
thunderbolt 0000:06:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0010 address=0xbb0e3400 flags=0x0020]
or
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [04:00.0] PASID ffffffff fault addr 69974000 [fault reason 05] PTE Write access is not set
The reason is unknown and hard to debug because we were not able to
reproduce this locally. This only happens on certain systems with Intel
Maple Ridge Thunderbolt controller. If there is a device connected when
the driver is loaded the issue does not happen either. Only when there
is nothing connected (so typically when the system is booted up).
We can work this around by sending the driver ready several times. After
a couple of retries the message goes through and the controller works
just fine. For this reason make the number of retries a parameter for
icm_request() and then for Maple Ridge (and Titan Ridge as they us the
same function but this should not matter) increase number of retries
while shortening the timeout accordingly.
Reported-by: Werner Sembach <wse@tuxedocomputers.com>
Reported-by: Konrad J Hambrick <kjhambrick@gmail.com>
Reported-by: Calvin Walton <calvin.walton@kepstin.ca>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=214259
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
| | |\ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty/serial driver fixes for 6.6-rc6 that resolve
some reported issues. Included in here are:
- serial core pm runtime fix for issue reported by many
- 8250_omap driver fix
- rs485 spinlock fix for reported problem
- ams-delta bugfix for previous tty api changes in -rc1 that missed
this driver that never seems to get built in any test systems
All of these have been in linux-next for over a week with no reported
problems"
* tag 'tty-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
ASoC: ti: ams-delta: Fix cx81801_receive() argument types
serial: core: Fix checks for tx runtime PM state
serial: 8250_omap: Fix errors with no_console_suspend
serial: Reduce spinlocked portion of uart_rs485_config()
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Maximilian reported that surface_serial_hub serdev tx does not work during
system suspend. During system suspend, runtime PM gets disabled in
__device_suspend_late(), and tx is unable to wake-up the serial core port
device that we use to check if tx is safe to start. Johan summarized the
regression noting that serdev tx no longer always works as earlier when the
serdev device is runtime PM active.
The serdev device and the serial core controller devices are siblings of
the serial port hardware device. The runtime PM usage count from serdev
device does not propagate to the serial core device siblings, it only
propagates to the parent.
In addition to the tx issue for suspend, testing for the serial core port
device can cause an unnecessary delay in enabling tx while waiting for the
serial core port device to wake-up. The serial core port device wake-up is
only needed to flush pending tx when the serial port hardware device was
in runtime PM suspended state.
To fix the regression, we need to check the runtime PM state of the parent
serial port hardware device for tx instead of the serial core port device.
As the serial port device drivers may or may not implement runtime PM, we
need to also add a check for pm_runtime_enabled().
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: stable <stable@kernel.org>
Fixes: 84a9582fd203 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231005075644.25936-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
We now get errors on system suspend if no_console_suspend is set as
reported by Thomas. The errors started with commit 20a41a62618d ("serial:
8250_omap: Use force_suspend and resume for system suspend").
Let's fix the issue by checking for console_suspend_enabled in the system
suspend and resume path.
Note that with this fix the checks for console_suspend_enabled in
omap8250_runtime_suspend() become useless. We now keep runtime PM usage
count for an attached kernel console starting with commit bedb404e91bb
("serial: 8250_port: Don't use power management for kernel console").
Fixes: 20a41a62618d ("serial: 8250_omap: Use force_suspend and resume for system suspend")
Cc: stable <stable@kernel.org>
Cc: Udit Kumar <u-kumar1@ti.com>
Reported-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230926061319.15140-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |/ /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Commit 44b27aec9d96 ("serial: core, 8250: set RS485 termination GPIO in
serial core") enabled support for RS485 termination GPIOs behind i2c
expanders by setting the GPIO outside of the critical section protected
by the port spinlock. Access to the i2c expander may sleep, which
caused a splat with the port spinlock held.
Commit 7c7f9bc986e6 ("serial: Deassert Transmit Enable on probe in
driver-specific way") erroneously regressed that by spinlocking the
GPIO manipulation again.
Fix by moving uart_rs485_config() (the function manipulating the GPIO)
outside of the spinlocked section and acquiring the spinlock inside of
uart_rs485_config() for the invocation of ->rs485_config() only.
This gets us one step closer to pushing the spinlock down into the
->rs485_config() callbacks which actually need it. (Some callbacks
do not want to be spinlocked because they perform sleepable register
accesses, see e.g. sc16is7xx_config_rs485().)
Stack trace for posterity:
Voluntary context switch within RCU read-side critical section!
WARNING: CPU: 0 PID: 56 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch
Call trace:
rcu_note_context_switch
__schedule
schedule
schedule_timeout
wait_for_completion_timeout
bcm2835_i2c_xfer
__i2c_transfer
i2c_transfer
i2c_transfer_buffer_flags
regmap_i2c_write
_regmap_raw_write_impl
_regmap_bus_raw_write
_regmap_write
_regmap_update_bits
regmap_update_bits_base
pca953x_gpio_set_value
gpiod_set_raw_value_commit
gpiod_set_value_nocheck
gpiod_set_value_cansleep
uart_rs485_config
uart_add_one_port
pl011_register_port
pl011_probe
Fixes: 7c7f9bc986e6 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Suggested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.1+
Link: https://lore.kernel.org/r/f3a35967c28b32f3c6432d0aa5936e6a9908282d.1695307688.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |\ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here is a small set of char/misc and other smaller driver subsystem
fixes for 6.6-rc6. Included in here are:
- lots of iio driver fixes
- binder memory leak fix
- mcb driver fixes
- counter driver fixes
- firmware loader documentation fix
- documentation update for embargoed hardware issues
All of these have been in linux-next for over a week with no reported
issues"
* tag 'char-misc-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (22 commits)
iio: pressure: ms5611: ms5611_prom_is_valid false negative bug
dt-bindings: iio: adc: adi,ad7292: Fix additionalProperties on channel nodes
iio: adc: ad7192: Correct reference voltage
iio: light: vcnl4000: Don't power on/off chip in config
iio: addac: Kconfig: update ad74413r selections
iio: pressure: dps310: Adjust Timeout Settings
iio: imu: bno055: Fix missing Kconfig dependencies
iio: adc: imx8qxp: Fix address for command buffer registers
iio: cros_ec: fix an use-after-free in cros_ec_sensors_push_data()
iio: irsd200: fix -Warray-bounds bug in irsd200_trigger_handler
dt-bindings: iio: rohm,bu27010: add missing vdd-supply to example
binder: fix memory leaks of spam and pending work
firmware_loader: Update contact emails for ABI docs
Documentation: embargoed-hardware-issues.rst: Clarify prenotifaction
mcb: remove is_added flag from mcb_device struct
coresight: tmc-etr: Disable warnings for allocation failures
coresight: Fix run time warnings while reusing ETR buffer
iio: admv1013: add mixer_vgate corner cases
iio: pressure: bmp280: Fix NULL pointer exception
iio: dac: ad3552r: Correct device IDs
...
|
| | | |\ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
1st set of IIO fixes for 6.6
Note last minute rebase to fix up a stale Fixes tag. All patches have been
in Linux-next for some time.
adi,ad3552r
- Fix swapped device IDs for the two parts that are supported.
adi,ad7192
- Use the right reference voltage source.
adi,ad7292
- Fix additionalProperties to be false, not true.
adi,ad74413
- Add missing Kconfig depends on IIO_BUFFER and IIO_TRIGGERED_BUFFER
adi,admv1013
- Fix up some corner cases for the mixer vgate register value.
bosch,bmp280
- Fix a null pointer dereference caused by a wrong boolean operator.
bosch,bno055
- Add missing Kconfig depends on IIO_BUFFER and IIO_TRIGGERED_BUFFER
freescale,imx8eqxp
- Fix some wrong register addresses.
google,cros_ec
- Fix a use after free if very badly timed buffer disable occurs by
holding the device in buffered mode.
infineon,dps310
- Expand a timeout so we don't hit it on working parts.
meas,m5611
- Allow for a ROM CRC of 0 as it is a valid value and there are devices
out there where it happens.
murata,irsd200
- Make sure the buffer used to build up the scan is large enough to take
the timestamp.
rohm,bu27010 binding
- Add a missing required vdd-supply
vishay,vcnl4000
- Don't power down chip in wrong place.
* tag 'iio-fixes-for-6.6a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: pressure: ms5611: ms5611_prom_is_valid false negative bug
dt-bindings: iio: adc: adi,ad7292: Fix additionalProperties on channel nodes
iio: adc: ad7192: Correct reference voltage
iio: light: vcnl4000: Don't power on/off chip in config
iio: addac: Kconfig: update ad74413r selections
iio: pressure: dps310: Adjust Timeout Settings
iio: imu: bno055: Fix missing Kconfig dependencies
iio: adc: imx8qxp: Fix address for command buffer registers
iio: cros_ec: fix an use-after-free in cros_ec_sensors_push_data()
iio: irsd200: fix -Warray-bounds bug in irsd200_trigger_handler
dt-bindings: iio: rohm,bu27010: add missing vdd-supply to example
iio: admv1013: add mixer_vgate corner cases
iio: pressure: bmp280: Fix NULL pointer exception
iio: dac: ad3552r: Correct device IDs
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The ms5611 driver falsely rejects lots of MS5607-02BA03-50 chips
with "PROM integrity check failed" because it doesn't accept a prom crc
value of zero as legitimate.
According to the datasheet for this chip (and the manufacturer's
application note about the PROM CRC), none of the possible values for the
CRC are excluded - but the current code in ms5611_prom_is_valid() ends with
return crc_orig != 0x0000 && crc == crc_orig
Discussed with the driver author (Tomasz Duszynski) and he indicated that
at that time (2015) he was dealing with some faulty chip samples which
returned blank data under some circumstances and/or followed example code
which indicated CRC zero being bad.
As far as I can tell this exception should not be applied anymore; We've
got a few hundred custom boards here with this chip where large numbers
of the prom have a legitimate CRC value 0, and do work fine, but which the
current driver code wrongly rejects.
Signed-off-by: Alexander Zangerl <az@breathe-safe.com>
Fixes: c0644160a8b5 ("iio: pressure: add support for MS5611 pressure and temperature sensor")
Link: https://lore.kernel.org/r/2535-1695168070.831792@Ze3y.dhYT.s3fx
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The avdd and the reference voltage are two different sources but the
reference voltage was assigned according to the avdd supply.
Add vref regulator structure and set the reference voltage according to
the vref supply from the devicetree.
In case vref supply is missing, reference voltage is set according to
the avdd supply for compatibility with old devicetrees.
Fixes: b581f748cce0 ("staging: iio: adc: ad7192: move out of staging")
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230924152149.41884-1-alisadariana@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
After enabling/disabling interrupts on the vcnl4040 chip the als and/or
ps sensor is powered on or off depending on the interrupt enable bits.
This is made as a last step in write_event_config.
But there is no reason to do this as the runtime PM handles the power
state of the sensors. Interfering with this may impact sensor readings.
Consider the following:
1. Userspace makes sensor data reading which triggers RPM resume
(sensor powered on) and a RPM suspend timeout. The timeout is 2000ms
before RPM suspend powers the sensor off if no new reading is made
within the timeout period.
2. Userspace disables interrupts => powers sensor off
3. Userspace reads sensor data = 0 because sensor is off and the
suspend timeout has not passed. For each new reading made within the
timeout period the timeout is renewed with 2000ms and RPM will not
make a new resume (device was not suspended). So the sensor will
not be powered on.
4. No further userspace reading for 2000ms ends RPM suspend timeout and
triggers suspend (powers off already powered off sensor).
Powering sensor off in (2) makes all consecutive readings made within
2000ms to the previous reading (3) return invalid data.
Skip setting power state when writing new event config.
Fixes: 546676121cb9 ("iio: light: vcnl4000: Add interrupt support for vcnl4040")
Fixes: bc292aaf9cb4 ("iio: light: vcnl4000: add illuminance irq vcnl4040/4200")
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20230907-vcnl4000-pm-fix-v2-1-298e01f54db4@axis.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Building ad74413r without selecting IIO_BUFFER and
IIO_TRIGGERED_BUFFER generates error with respect to the iio trigger
functions that are used within the driver.
Update the Kconfig accordingly.
Fixes: fea251b6a5db ("iio: addac: add AD74413R driver")
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20230912085421.51102-1-antoniu.miclaus@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The DPS310 sensor chip has been encountering intermittent errors while
reading the sensor device across various system designs. This issue causes
the chip to become "stuck," preventing the indication of "ready" status
for pressure and temperature measurements in the MEAS_CFG register.
To address this issue, this commit fixes the timeout settings to improve
sensor stability:
- After sending a reset command to the chip, the timeout has been extended
from 2.5 ms to 15 ms, aligning with the DPS310 specification.
- The read timeout value of the MEAS_CFG register has been adjusted from
20ms to 30ms to match the specification.
Signed-off-by: Lakshmi Yadlapati <lakshmiy@us.ibm.com>
Fixes: 7b4ab4abcea4 ("iio: pressure: dps310: Reset chip after timeout")
Link: https://lore.kernel.org/r/20230829180222.3431926-2-lakshmiy@us.ibm.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This driver uses IIO triggered buffers so it needs to select them in
Kconfig.
on riscv-32bit:
/opt/crosstool/gcc-13.2.0-nolibc/riscv32-linux/bin/riscv32-linux-ld: drivers/iio/imu/bno055/bno055.o: in function `.L367':
bno055.c:(.text+0x2c96): undefined reference to `devm_iio_triggered_buffer_setup_ext'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/linux-next/40566b4b-3950-81fe-ff14-871d8c447627@infradead.org/
Fixes: 4aefe1c2bd0c ("iio: imu: add Bosch Sensortec BNO055 core driver")
Cc: Andrea Merello <andrea.merello@iit.it>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20230903113052.846298-1-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The ADC Command Buffer Register high and low are currently pointing to
the wrong address and makes it impossible to perform correct
ADC measurements over all channels.
According to the datasheet of the imx8qxp the ADC_CMDL register starts
at address 0x100 and the ADC_CMDH register starts at address 0x104.
This bug seems to be in the kernel since the introduction of this
driver.
This can be observed by checking all raw voltages of the adc and they
are all nearly identical:
cat /sys/bus/iio/devices/iio\:device0/in_voltage*_raw
3498
3494
3491
3491
3489
3490
3490
3490
Fixes: 1e23dcaa1a9fa ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC")
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20230904220204.23841-1-embed3d@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
cros_ec_sensors_push_data() reads `indio_dev->active_scan_mask` and
calls iio_push_to_buffers_with_timestamp() without making sure the
`indio_dev` stays in buffer mode. There is a race if `indio_dev` exits
buffer mode right before cros_ec_sensors_push_data() accesses them.
An use-after-free on `indio_dev->active_scan_mask` was observed. The
call trace:
[...]
_find_next_bit
cros_ec_sensors_push_data
cros_ec_sensorhub_event
blocking_notifier_call_chain
cros_ec_irq_thread
It was caused by a race condition: one thread just freed
`active_scan_mask` at [1]; while another thread tried to access the
memory at [2].
Fix it by calling iio_device_claim_buffer_mode() to ensure the
`indio_dev` can't exit buffer mode during cros_ec_sensors_push_data().
[1]: https://elixir.bootlin.com/linux/v6.5/source/drivers/iio/industrialio-buffer.c#L1189
[2]: https://elixir.bootlin.com/linux/v6.5/source/drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.c#L198
Cc: stable@vger.kernel.org
Fixes: aa984f1ba4a4 ("iio: cros_ec: Register to cros_ec_sensorhub when EC supports FIFO")
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230829030622.1571852-1-tzungbi@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When compiling with gcc 13 with -Warray-bounds enabled:
In file included from drivers/iio/proximity/irsd200.c:15:
In function ‘iio_push_to_buffers_with_timestamp’,
inlined from ‘irsd200_trigger_handler’ at drivers/iio/proximity/irsd200.c:770:2:
./include/linux/iio/buffer.h:42:46: error: array subscript ‘int64_t {aka long long int}[0]’
is partly outside array bounds of ‘s16[1]’ {aka ‘short int[1]’} [-Werror=array-bounds=]
42 | ((int64_t *)data)[ts_offset] = timestamp;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~
drivers/iio/proximity/irsd200.c: In function ‘irsd200_trigger_handler’:
drivers/iio/proximity/irsd200.c:763:13: note: object ‘buf’ of size 2
763 | s16 buf = 0;
| ^~~
The problem seems to be that irsd200_trigger_handler() is taking a s16
variable as an int64_t buffer. As Jonathan suggested [1], fix it by
extending the buffer to a two-element array of s64.
Link: https://github.com/KSPP/linux/issues/331
Link: https://lore.kernel.org/lkml/20230809181329.46c00a5d@jic23-huawei/ [1]
Fixes: 3db3562bc66e ("iio: Add driver for Murata IRS-D200")
Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com>
Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Waqar Hameed <waqar.hameed@axis.com>
Tested-by: Waqar Hameed <waqar.hameed@axis.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230810035910.1334706-1-gongruiqi@huaweicloud.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Include the corner cases in the computation of the MIXER_VGATE register
value.
According to the datasheet: The MIXER_VGATE values follows the VCM such
as, that for a 0V to 1.8V VCM, MIXER_VGATE = 23.89 VCM + 81, and for a >
1.8V to 2.6V VCM, MIXER_VGATE = 23.75 VCM + 1.25.
Fixes: da35a7b526d9 ("iio: frequency: admv1013: add support for ADMV1013")
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230807143806.6954-1-antoniu.miclaus@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
