| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
| |
Add a fan sensor to report RPM's from a fan tach input.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
| |
The voltage telemetry registers for Zen2 are different from Zen1. Also
the factors of CPU current values are changed on Zen2. Add new definitions
for these register.
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Link: https://lore.kernel.org/r/20200827054242.2347-2-wei.huang2@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
| |
Many SMN thermal registers in Zen CPU families are common across different
generations. For long-term code maintenance, it is better to rename these
macro and function names to Zen.
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Link: https://lore.kernel.org/r/20200827054242.2347-1-wei.huang2@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
| |
Use semicolons and braces.
Signed-off-by: Joe Perches <joe@perches.com>
Link: https://lore.kernel.org/r/5e1ca60df261e3bfd0e6510e388581a1d1f52c77.1598331149.git.joe@perches.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Use the nvmem kernel api to expose the black box
chip functionality to userspace.
Using this feature, the device is capable of recording
to nonvolatile flash memory the vital data about the
system status that caused the system to perform a
black box write.
A blackbox is 64 bytes of data containing all the
status registers, last two states of the sequencer,
timestamp and counters. The mapping of this data is
described in the adm1266 datasheet.
On power-up the driver sets the unix time to
the adm1266 using the SET_RTC command. This value
is incremented by an internal clock and it is used
as timestamp for the black box feature.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-6-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
| |
Add a debugfs entry which prints the current state
of the adm1266 sequencer.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-5-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Adm1266 exposes 9 GPIOs and 16 PDIOs which are currently read-only. They
are controlled by the internal sequencing engine.
This patch makes adm1266 driver expose GPIOs and PDIOs to user-space
using GPIO provider kernel api.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-4-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
PmBus devices support Block Write-Block Read Process
Call described in SMBus specification v 2.0 with the
exception that Block writes and reads are permitted to
have up 255 data bytes instead of max 32 bytes (SMBus).
This patch adds Block WR process call support for ADM1266.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-3-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add pmbus probing driver for the adm1266 Cascadable
Super Sequencer with Margin Control and Fault Recording.
Driver is using the pmbus_core, creating sysfs files
under hwmon for inputs: vh1->vh4 and vp1->vp13.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-2-alexandru.tachici@analog.com
[groeck: Use .probe_new function, adjust for changed pmbus_do_probe API]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
| |
Add support for DTS bindings for the sensirion shtc1,shtw1 and shtc3.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200815012227.32538-2-chris.ruehl@gtsys.com.hk
[groeck: Resolved conflicts]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
| |
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1597649673-22329-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
| |
As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160035.590142-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
| |
As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160159.591293-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
| |
As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160231.592571-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Many hwmon drivers don't use the id information provided by the old
i2c probe function, and the remainder can easily be adapted to the new
form ("probe_new") by calling i2c_match_id explicitly.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified to call i2c_match_id() with the same level of
error-handling (if any) as before.
This patch wraps up the transition for hwmon, with four stragglers not
included in the previous large patch.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160354.594715-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
| |
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162851.1519546-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
| |
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162704.1517951-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
| |
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162544.1516647-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
| |
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162300.1514695-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
| |
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162026.1512242-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
| |
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813161845.1511261-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/20200813161129.1507599-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
| |
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813160958.1506536-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Many hwmon drivers don't use the id information provided by the old
i2c probe function, and the remainder can easily be adapted to the new
form ("probe_new") by calling i2c_match_id explicitly.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
A few drivers aren't included in this patch because they have a
different set of maintainers. They will be covered by other patches.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813160222.1503401-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
pmbus_do_probe doesn't use the id information provided in its second
argument, so this can be removed, which then allows using the
single-parameter i2c probe function ("probe_new") for probes.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* configured v. probed comparisons are performed by comparing the
configured name to the detected name, instead of the ids; this
involves strcmp but is still cheaper than comparing all the device
names when scanning the tables;
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
Additionally, the mismatch message in the ltc2978 driver is adjusted
so that it no longer assumes that the driver_data is an index into
ltc2978_id.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Adding implementation for new attributes (rated_min/rated_max) to
cover PMBus specification about rated values reporting:
MFR_VIN_MIN, MFR_VIN_MAX, MFR_IIN_MAX, MFR_PIN_MAX, MFR_VOUT_MIN,
MFR_VOUT_MAX, MFR_IOUT_MAX, MFR_POUT_MAX, MFR_MAX_TEMP_1/2/3.
Tested with OpenBMC stack. All rated attributes were available
and reported correct values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-4-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Adding implementation for new attributes (rated_min/rated_max) for
currentX, inX, powerX, tempX and humidityX.
Tested with OpenBMC stack and simple hwmon driver using
rated_min/rated_max for the following types of sensors: hwmon_temp,
hwmon_in, hwmon_curr, hwmon_power, hwmon_humidity.
For each sensor rated attributes were available and returned
expected values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-3-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Smatch has a new check for resource leaks which found a bug in probe:
drivers/hwmon/w83627ehf.c:2417 w83627ehf_probe()
warn: 'res->start' not released on lines: 2412.
We need to clean up if devm_hwmon_device_register_with_info() fails.
Fixes: 266cd5835947 ("hwmon: (w83627ehf) convert to with_info interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20200921125212.GA1128194@mwanda
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Starting with MAX34451, the chips of this series support STATUS_IOUT and
STATUS_TEMPERATURE commands, and no longer report over-current and
over-temperature status with STATUS_MFR_SPECIFIC.
Fixes: 7a001dbab4ade ("hwmon: (pmbus/max34440) Add support for MAX34451.")
Fixes: 50115ac9b6f35 ("hwmon: (pmbus/max34440) Add support for MAX34460 and MAX34461")
Reported-by: Steve Foreman <foremans@google.com>
Cc: Steve Foreman <foremans@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If the temperature is read before the internal calibration is
completed, the driver returns -EIO. Instead it should return -EAGAIN
to encourage repeating the operation.
Note (groeck): Returning -EAGAIN to userspace may result in hard loops;
some userspace code interprets -EAGAIN as request to retry immediately.
I would prefer -ENODATA, but it turns out that the thermal subsystem only
handles -EAGAIN silently, so we'll have to stick with that.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200903134704.8949-1-lars.povlsen@microchip.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fix from Borislav Petkov:
"Ensure that the EFI bootloader control module only probes successfully
on systems that support the EFI SetVariable runtime service"
[ Tag and commit from Ard Biesheuvel, forwarded by Borislav ]
* tag 'efi-urgent-for-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: efibc: check for efivars write capability
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Branden reports that commit
f88814cc2578c1 ("efi/efivars: Expose RT service availability via efivars abstraction")
regresses UEFI platforms that implement GetVariable but not SetVariable
when booting kernels that have EFIBC (bootloader control) enabled.
The reason is that EFIBC is a user of the efivars abstraction, which was
updated to permit users that rely only on the read capability, but not on
the write capability. EFIBC is in the latter category, so it has to check
explicitly whether efivars supports writes.
Fixes: f88814cc2578c1 ("efi/efivars: Expose RT service availability via efivars abstraction")
Tested-by: Branden Sherrell <sherrellbc@gmail.com>
Link: https://lore.kernel.org/linux-efi/AE217103-C96F-4AFC-8417-83EC11962004@gmail.com/
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A handful of fixes to address a string of mistakes in the mechanism
for device-mapper to determine if its component devices are dax
capable.
- Fix an original bug in device-mapper table reference counting when
interrogating dax capability in the component device. This bug was
hidden by the following bug.
- Fix device-mapper to use the proper helper (dax_supported() instead
of the leaf helper generic_fsdax_supported()) to determine dax
operation of a stacked block device configuration. The original
implementation is only valid for one level of dax-capable block
device stacking. This bug was discovered while fixing the below
regression.
- Fix an infinite recursion regression introduced by broken attempts
to quiet the generic_fsdax_supported() path and make it bail out
before logging "dax capability not found" errors"
* tag 'libnvdimm-fixes-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: Fix stack overflow when mounting fsdax pmem device
dm: Call proper helper to determine dax support
dm/dax: Fix table reference counts
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When mounting fsdax pmem device, commit 6180bb446ab6 ("dax: fix
detection of dax support for non-persistent memory block devices")
introduces the stack overflow [1][2]. Here is the call path for
mounting ext4 file system:
ext4_fill_super
bdev_dax_supported
__bdev_dax_supported
dax_supported
generic_fsdax_supported
__generic_fsdax_supported
bdev_dax_supported
The call path leads to the infinite calling loop, so we cannot
call bdev_dax_supported() in __generic_fsdax_supported(). The sanity
checking of the variable 'dax_dev' is moved prior to the two
bdev_dax_pgoff() checks [3][4].
[1] https://lore.kernel.org/linux-nvdimm/1420999447.1004543.1600055488770.JavaMail.zimbra@redhat.com/
[2] https://lore.kernel.org/linux-nvdimm/alpine.LRH.2.02.2009141131220.30651@file01.intranet.prod.int.rdu2.redhat.com/
[3] https://lore.kernel.org/linux-nvdimm/CA+RJvhxBHriCuJhm-D8NvJRe3h2MLM+ZMFgjeJjrRPerMRLvdg@mail.gmail.com/
[4] https://lore.kernel.org/linux-nvdimm/20200903160608.GU878166@iweiny-DESK2.sc.intel.com/
Fixes: 6180bb446ab6 ("dax: fix detection of dax support for non-persistent memory block devices")
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com>
Cc: Coly Li <colyli@suse.de>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: John Pittman <jpittman@redhat.com>
Link: https://lore.kernel.org/r/20200917111549.6367-1-adrianhuang0701@gmail.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
DM was calling generic_fsdax_supported() to determine whether a device
referenced in the DM table supports DAX. However this is a helper for "leaf" device drivers so that
they don't have to duplicate common generic checks. High level code
should call dax_supported() helper which that calls into appropriate
helper for the particular device. This problem manifested itself as
kernel messages:
dm-3: error: dax access failed (-95)
when lvm2-testsuite run in cases where a DM device was stacked on top of
another DM device.
Fixes: 7bf7eac8d648 ("dax: Arrange for dax_supported check to span multiple devices")
Cc: <stable@vger.kernel.org>
Tested-by: Adrian Huang <ahuang12@lenovo.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/160061715195.13131.5503173247632041975.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
A recent fix to the dm_dax_supported() flow uncovered a latent bug. When
dm_get_live_table() fails it is still required to drop the
srcu_read_lock(). Without this change the lvm2 test-suite triggers this
warning:
# lvm2-testsuite --only pvmove-abort-all.sh
WARNING: lock held when returning to user space!
5.9.0-rc5+ #251 Tainted: G OE
------------------------------------------------
lvm/1318 is leaving the kernel with locks still held!
1 lock held by lvm/1318:
#0: ffff9372abb5a340 (&md->io_barrier){....}-{0:0}, at: dm_get_live_table+0x5/0xb0 [dm_mod]
...and later on this hang signature:
INFO: task lvm:1344 blocked for more than 122 seconds.
Tainted: G OE 5.9.0-rc5+ #251
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:lvm state:D stack: 0 pid: 1344 ppid: 1 flags:0x00004000
Call Trace:
__schedule+0x45f/0xa80
? finish_task_switch+0x249/0x2c0
? wait_for_completion+0x86/0x110
schedule+0x5f/0xd0
schedule_timeout+0x212/0x2a0
? __schedule+0x467/0xa80
? wait_for_completion+0x86/0x110
wait_for_completion+0xb0/0x110
__synchronize_srcu+0xd1/0x160
? __bpf_trace_rcu_utilization+0x10/0x10
__dm_suspend+0x6d/0x210 [dm_mod]
dm_suspend+0xf6/0x140 [dm_mod]
Fixes: 7bf7eac8d648 ("dax: Arrange for dax_supported check to span multiple devices")
Cc: <stable@vger.kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Reported-by: Adrian Huang <ahuang12@lenovo.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Adrian Huang <ahuang12@lenovo.com>
Link: https://lore.kernel.org/r/160045867590.25663.7548541079217827340.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A fix for a lockdep issue to avoid an asserting triggering during
early boot. There shouldn't be any incorrect behavior as the system
isn't concurrent at the time.
- The addition of a missing fence when installing early fixmap
mappings.
- A corretion to the K210 device tree's interrupt map.
- A fix for M-mode timer handling on the K210.
* tag 'riscv-for-linus-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Resurrect the MMIO timer implementation for M-mode systems
riscv: Fix Kendryte K210 device tree
riscv: Add sfence.vma after early page table changes
RISC-V: Take text_mutex in ftrace_init_nop()
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The K210 doesn't implement rdtime in M-mode, and since that's where Linux runs
in the NOMMU systems that means we can't use rdtime. The K210 is the only
system that anyone is currently running NOMMU or M-mode on, so here we're just
inlining the timer read directly.
This also adds the CLINT driver as an !MMU dependency, as it's currently the
only timer driver availiable for these systems and without it we get a build
failure for some configurations.
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt fixes from Greg KH:
"Here are some small USB and one Thunderbolt driver fixes.
Nothing major at all, just some fixes for reported issues, and a quirk
addition:
- typec fixes
- UAS disconnect fix
- usblp race fix
- ehci-hcd modversions build fix
- ignore wakeup quirk table addition
- thunderbolt DROM read fix
All of these have been in linux-next with no reported issues"
* tag 'usb-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usblp: fix race between disconnect() and read()
ehci-hcd: Move include to keep CRC stable
usb: typec: intel_pmc_mux: Handle SCU IPC error conditions
USB: quirks: Add USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for BYD zhaoxin notebook
USB: UAS: fix disconnect by unplugging a hub
usb: typec: ucsi: Prevent mode overrun
usb: typec: ucsi: acpi: Increase command completion timeout value
thunderbolt: Retry DROM read once if parsing fails
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
read() needs to check whether the device has been
disconnected before it tries to talk to the device.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+be5b5f86a162a6c281e6@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20200917103427.15740-1-oneukum@suse.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The CRC calculation done by genksyms is triggered when the parser hits
EXPORT_SYMBOL*() macros. At this point, genksyms recursively expands the
types of the function parameters, and uses that as the input for the CRC
calculation. In the case of forward-declared structs, the type expands
to 'UNKNOWN'. Following this, it appears that the result of the
expansion of each type is cached somewhere, and seems to be re-used
when/if the same type is seen again for another exported symbol in the
same C file.
Unfortunately, this can cause CRC 'stability' issues when a struct
definition becomes visible in the middle of a C file. For example, let's
assume code with the following pattern:
struct foo;
int bar(struct foo *arg)
{
/* Do work ... */
}
EXPORT_SYMBOL_GPL(bar);
/* This contains struct foo's definition */
#include "foo.h"
int baz(struct foo *arg)
{
/* Do more work ... */
}
EXPORT_SYMBOL_GPL(baz);
Here, baz's CRC will be computed using the expansion of struct foo that
was cached after bar's CRC calculation ('UNKOWN' here). But if
EXPORT_SYMBOL_GPL(bar) is removed from the file (because of e.g. symbol
trimming using CONFIG_TRIM_UNUSED_KSYMS), struct foo will be expanded
late, during baz's CRC calculation, which now has visibility over the
full struct definition, hence resulting in a different CRC for baz.
The proper fix for this certainly is in genksyms, but that will take me
some time to get right. In the meantime, we have seen one occurrence of
this in the ehci-hcd code which hits this problem because of the way it
includes C files halfway through the code together with an unlucky mix
of symbol trimming.
In order to workaround this, move the include done in ehci-hub.c early
in ehci-hcd.c, hence making sure the struct definitions are visible to
the entire file. This improves CRC stability of the ehci-hcd exports
even when symbol trimming is enabled.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20200916171825.3228122-1-qperret@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Check and return if there are errors. The response bits are valid
only on no errors.
Fixes: b7404a29cd3d ("usb: typec: intel_pmc_mux: Definitions for response status bits")
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916091102.27118-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Add a USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for the BYD zhaoxin notebook.
This notebook come with usb touchpad. And we would like to disable
touchpad wakeup on this notebook by default.
Signed-off-by: Penghao <penghao@uniontech.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200907023026.28189-1-penghao@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The SCSI layer can go into an ugly loop if you ignore that a device is
gone. You need to report an error in the command rather than in the
return value of the queue method.
We need to specifically check for ENODEV. The issue goes back to the
introduction of the driver.
Fixes: 115bb1ffa54c3 ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200916094026.30085-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Sometimes the embedded controller firmware does not
terminate the list of alternate modes that the partner
supports in its response to the GET_ALTERNATE_MODES command.
Instead the firmware returns the supported alternate modes
over and over again until the driver stops requesting them.
If that happens, the number of modes for each alternate mode
will exceed the maximum 6 that is defined in the USB Power
Delivery specification. Making sure that can't happen by
adding a check for it.
This fixes NULL pointer dereference that is caused by the
overrun.
Fixes: ad74b8649beaf ("usb: typec: ucsi: Preliminary support for alternate modes")
Cc: stable@vger.kernel.org
Reported-by: Zwane Mwaikambo <zwanem@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916090034.25119-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
UCSI specification quite clearly states that if a command
can't be completed in 10ms, the firmware must notify
about BUSY condition. Unfortunately almost none of the
platforms (the firmware on them) generate the BUSY
notification even if a command can't be completed in time.
The driver already considered that, and used a timeout
value of 5 seconds, but processing especially the alternate
mode discovery commands takes often considerable amount of
time from the firmware, much more than the 5 seconds. That
happens especially after bootup when devices are already
connected to the USB Type-C connector. For now on those
platforms the alternate mode discovery has simply failed
because of the timeout.
To improve the situation, increasing the timeout value for
the command completion to 1 minute. That should give enough
time for even the slowest firmware to process the commands.
Fixes: f56de278e8ec ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916090034.25119-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\ \ \ \
| | |_|/ /
| |/| | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
thunderbolt: Fix for v5.9-rc6
One more fix that makes ASUS PA27AC Thunderbolt 3 monitor work more
reliably.
This has been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Retry DROM read once if parsing fails
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Kai-Heng reported that sometimes DROM parsing of ASUS PA27AC Thunderbolt 3
monitor fails. This makes the driver to fail to add the device so only
DisplayPort tunneling is functional.
It is not clear what exactly happens but waiting for 100 ms and retrying
the read seems to work this around so we do that here.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206493
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|\ \ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial/fbcon fixes from Greg KH:
"Here are some small tty/serial and one more fbcon fix.
They include:
- serial core locking regression fixes
- new device ids for 8250_pci driver
- fbcon fix for syzbot found issue
All have been in linux-next with no reported issues"
* tag 'tty-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
fbcon: Fix user font detection test at fbcon_resize().
serial: 8250_pci: Add Realtek 816a and 816b
serial: core: fix console port-lock regression
serial: core: fix port-lock initialisation
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
syzbot is reporting OOB read at fbcon_resize() [1], for
commit 39b3cffb8cf31117 ("fbcon: prevent user font height or width change
from causing potential out-of-bounds access") is by error using
registered_fb[con2fb_map[vc->vc_num]]->fbcon_par->p->userfont (which was
set to non-zero) instead of fb_display[vc->vc_num].userfont (which remains
zero for that display).
We could remove tricky userfont flag [2], for we can determine it by
comparing address of the font data and addresses of built-in font data.
But since that commit is failing to fix the original OOB read [3], this
patch keeps the change minimal in case we decide to revert altogether.
[1] https://syzkaller.appspot.com/bug?id=ebcbbb6576958a496500fee9cf7aa83ea00b5920
[2] https://syzkaller.appspot.com/text?tag=Patch&x=14030853900000
[3] https://syzkaller.appspot.com/bug?id=6fba8c186d97cf1011ab17660e633b1cc4e080c9
Reported-by: syzbot <syzbot+b38b1ef6edf0c74a8d97@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 39b3cffb8cf31117 ("fbcon: prevent user font height or width change from causing potential out-of-bounds access")
Cc: George Kennedy <george.kennedy@oracle.com>
Link: https://lore.kernel.org/r/f6e3e611-8704-1263-d163-f52c906a4f06@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|