summaryrefslogtreecommitdiffstats
path: root/drivers
Commit message (Collapse)AuthorAgeFilesLines
* Merge tag 'net-5.10-rc6' of ↵Linus Torvalds2020-11-2736-401/+524
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Networking fixes for 5.10-rc6, including fixes from the WiFi driver, and CAN subtrees. Current release - regressions: - gro_cells: reduce number of synchronize_net() calls - ch_ktls: release a lock before jumping to an error path Current release - always broken: - tcp: Allow full IP tos/IPv6 tclass to be reflected in L3 header Previous release - regressions: - net/tls: fix missing received data after fast remote close - vsock/virtio: discard packets only when socket is really closed - sock: set sk_err to ee_errno on dequeue from errq - cxgb4: fix the panic caused by non smac rewrite Previous release - always broken: - tcp: fix corner cases around setting ECN with BPF selection of congestion control - tcp: fix race condition when creating child sockets from syncookies on loopback interface - usbnet: ipheth: fix connectivity with iOS 14 - tun: honor IOCB_NOWAIT flag - net/packet: fix packet receive on L3 devices without visible hard header - devlink: Make sure devlink instance and port are in same net namespace - net: openvswitch: fix TTL decrement action netlink message format - bonding: wait for sysfs kobject destruction before freeing struct slave - net: stmmac: fix upstream patch applied to the wrong context - bnxt_en: fix return value and unwind in probe error paths Misc: - devlink: add extra layer of categorization to the reload stats uAPI before it's released" * tag 'net-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (68 commits) sock: set sk_err to ee_errno on dequeue from errq mptcp: fix NULL ptr dereference on bad MPJ net: openvswitch: fix TTL decrement action netlink message format can: af_can: can_rx_unregister(): remove WARN() statement from list operation sanity check can: m_can: m_can_dev_setup(): add support for bosch mcan version 3.3.0 can: m_can: fix nominal bitiming tseg2 min for version >= 3.1 can: m_can: m_can_open(): remove IRQF_TRIGGER_FALLING from request_threaded_irq()'s flags can: mcp251xfd: mcp251xfd_probe(): bail out if no IRQ was given can: gs_usb: fix endianess problem with candleLight firmware ch_ktls: lock is not freed net/tls: Protect from calling tls_dev_del for TLS RX twice devlink: Make sure devlink instance and port are in same net namespace devlink: Hold rtnl lock while reading netdev attributes ptp: clockmatrix: bug fix for idtcm_strverscmp enetc: Let the hardware auto-advance the taprio base-time of 0 gro_cells: reduce number of synchronize_net() calls net: stmmac: fix incorrect merge of patch upstream ipv6: addrlabel: fix possible memory leak in ip6addrlbl_net_init Documentation: netdev-FAQ: suggest how to post co-dependent series ibmvnic: enhance resetting status check during module exit ...
| * can: m_can: m_can_dev_setup(): add support for bosch mcan version 3.3.0Pankaj Sharma2020-11-271-0/+2
| | | | | | | | | | | | | | | | | | | | Add support for mcan bit timing and control mode according to bosch mcan IP version 3.3.0. The mcan version read from the Core Release field of CREL register would be 33. Accordingly the properties are to be set for mcan v3.3.0 Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com> Link: https://lore.kernel.org/r/1606366302-5520-1-git-send-email-pankj.sharma@samsung.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
| * can: m_can: fix nominal bitiming tseg2 min for version >= 3.1Marc Kleine-Budde2020-11-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At lest the revision 3.3.0 of the bosch m_can IP core specifies that valid register values for "Nominal Time segment after sample point (NTSEG2)" are from 1 to 127. As the hardware uses a value of one more than the programmed value, mean tseg2_min is 2. This patch fixes the tseg2_min value accordingly. Cc: Dan Murphy <dmurphy@ti.com> Cc: Mario Huettel <mario.huettel@gmx.net> Acked-by: Sriram Dash <sriram.dash@samsung.com> Link: https://lore.kernel.org/r/20201124190751.3972238-1-mkl@pengutronix.de Fixes: b03cfc5bb0e1 ("can: m_can: Enable M_CAN version dependent initialization") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
| * can: m_can: m_can_open(): remove IRQF_TRIGGER_FALLING from ↵Marc Kleine-Budde2020-11-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | request_threaded_irq()'s flags The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING when requesting the IRQ. As this can result in missing interrupts. Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW", unloading and reloading of the driver results in the following error during ifup: | irq: type mismatch, failed to map hwirq-31 for gpio@20a8000! | tcan4x5x spi1.1: m_can device registered (irq=0, version=32) | tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized. | tcan4x5x spi1.1 can2: failed to request interrupt This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the request_threaded_irq(). Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework") Cc: Dan Murphy <dmurphy@ti.com> Cc: Sriram Dash <sriram.dash@samsung.com> Cc: Pankaj Sharma <pankj.sharma@samsung.com> Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
| * can: mcp251xfd: mcp251xfd_probe(): bail out if no IRQ was givenMarc Kleine-Budde2020-11-261-0/+4
| | | | | | | | | | | | | | | | | | | | | | This patch add a check to the mcp251xfd_probe() function to bail out and give the user a proper error message if no IRQ is specified. Otherwise the driver will probe just fine but ifup will fail with a meaningless "RTNETLINK answers: Invalid argument" error message. Link: https://lore.kernel.org/r/20201123113522.3820052-1-mkl@pengutronix.de Reported-by: Niels Petter <petter@ka-long.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
| * can: gs_usb: fix endianess problem with candleLight firmwareMarc Kleine-Budde2020-11-261-61/+70
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The firmware on the original USB2CAN by Geschwister Schneider Technologie Entwicklungs- und Vertriebs UG exchanges all data between the host and the device in host byte order. This is done with the struct gs_host_config::byte_order member, which is sent first to indicate the desired byte order. The widely used open source firmware candleLight doesn't support this feature and exchanges the data in little endian byte order. This breaks if a device with candleLight firmware is used on big endianess systems. To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which is a transparent cookie) are converted to __le32. Cc: Maximilian Schneider <max@schneidersoft.net> Cc: Hubert Denkmair <hubert@denkmair.de> Reported-by: Michael Rausch <mr@netadair.de> Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices") Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
| * ch_ktls: lock is not freedRohit Maheshwari2020-11-251-1/+3
| | | | | | | | | | | | | | | | | | | | Currently lock gets freed only if timeout expires, but missed a case when HW returns failure and goes for cleanup. Fixes: efca3878a5fb ("ch_ktls: Issue if connection offload fails") Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com> Link: https://lore.kernel.org/r/20201125072626.10861-1-rohitm@chelsio.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * ptp: clockmatrix: bug fix for idtcm_strverscmpMin Li2020-11-251-33/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Feed kstrtou8 with NULL terminated string. Changes since v1: -Use sscanf to get rid of adhoc string parse. Changes since v2: -Check if sscanf returns 3. Fixes: 7ea5fda2b132 ("ptp: ptp_clockmatrix: update to support 4.8.7 firmware") Signed-off-by: Min Li <min.li.xe@renesas.com> Link: https://lore.kernel.org/r/1606273115-25792-1-git-send-email-min.li.xe@renesas.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * enetc: Let the hardware auto-advance the taprio base-time of 0Vladimir Oltean2020-11-251-12/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The tc-taprio base time indicates the beginning of the tc-taprio schedule, which is cyclic by definition (where the length of the cycle in nanoseconds is called the cycle time). The base time is a 64-bit PTP time in the TAI domain. Logically, the base-time should be a future time. But that imposes some restrictions to user space, which has to retrieve the current PTP time from the NIC first, then calculate a base time that will still be larger than the base time by the time the kernel driver programs this value into the hardware. Actually ensuring that the programmed base time is in the future is still a problem even if the kernel alone deals with this. Luckily, the enetc hardware already advances a base-time that is in the past into a congruent time in the immediate future, according to the same formula that can be found in the software implementation of taprio (in taprio_get_start_time): /* Schedule the start time for the beginning of the next * cycle. */ n = div64_s64(ktime_sub_ns(now, base), cycle); *start = ktime_add_ns(base, (n + 1) * cycle); There's only one problem: the driver doesn't let the hardware do that. It interferes with the base-time passed from user space, by special-casing the situation when the base-time is zero, and replaces that with the current PTP time. This changes the intended effective base-time of the schedule, which will in the end have a different phase offset than if the base-time of 0.000000000 was to be advanced by an integer multiple of the cycle-time. Fixes: 34c6adf1977b ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20201124220259.3027991-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: stmmac: fix incorrect merge of patch upstreamAntonio Borneo2020-11-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a") was intended to modify the struct dwmac410_ops, but it got somehow badly merged and modified the struct dwmac4_ops. Revert the modification in struct dwmac4_ops and re-apply it properly in struct dwmac410_ops. Fixes: 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a") Signed-off-by: Antonio Borneo <antonio.borneo@st.com> Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Link: https://lore.kernel.org/r/20201124223729.886992-1-antonio.borneo@st.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * ibmvnic: enhance resetting status check during module exitLijun Pan2020-11-242-4/+2
| | | | | | | | | | | | | | | | | | | | | | Based on the discussion with Sukadev Bhattiprolu and Dany Madden, we believe that checking adapter->resetting bit is preferred since RESETTING state flag is not as strict as resetting bit. RESETTING state flag is removed since it is verbose now. Fixes: 7d7195a026ba ("ibmvnic: Do not process device remove during device reset") Signed-off-by: Lijun Pan <ljp@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * ibmvnic: fix NULL pointer dereference in ibmvic_reset_crqLijun Pan2020-11-241-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | crq->msgs could be NULL if the previous reset did not complete after freeing crq->msgs. Check for NULL before dereferencing them. Snippet of call trace: ... ibmvnic 30000003 env3 (unregistering): Releasing sub-CRQ ibmvnic 30000003 env3 (unregistering): Releasing CRQ BUG: Kernel NULL pointer dereference on read at 0x00000000 Faulting instruction address: 0xc0000000000c1a30 Oops: Kernel access of bad area, sig: 11 [#1] LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries Modules linked in: ibmvnic(E-) rpadlpar_io rpaphp xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables xsk_diag tcp_diag udp_diag tun raw_diag inet_diag unix_diag bridge af_packet_diag netlink_diag stp llc rfkill sunrpc pseries_rng xts vmx_crypto uio_pdrv_genirq uio binfmt_misc ip_tables xfs libcrc32c sd_mod t10_pi sg ibmvscsi ibmveth scsi_transport_srp dm_mirror dm_region_hash dm_log dm_mod [last unloaded: ibmvnic] CPU: 20 PID: 8426 Comm: kworker/20:0 Tainted: G E 5.10.0-rc1+ #12 Workqueue: events __ibmvnic_reset [ibmvnic] NIP: c0000000000c1a30 LR: c008000001b00c18 CTR: 0000000000000400 REGS: c00000000d05b7a0 TRAP: 0380 Tainted: G E (5.10.0-rc1+) MSR: 800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 44002480 XER: 20040000 CFAR: c0000000000c19ec IRQMASK: 0 GPR00: 0000000000000400 c00000000d05ba30 c008000001b17c00 0000000000000000 GPR04: 0000000000000000 0000000000000000 0000000000000000 00000000000001e2 GPR08: 000000000001f400 ffffffffffffd950 0000000000000000 c008000001b0b280 GPR12: c0000000000c19c8 c00000001ec72e00 c00000000019a778 c00000002647b440 GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR20: 0000000000000006 0000000000000001 0000000000000003 0000000000000002 GPR24: 0000000000001000 c008000001b0d570 0000000000000005 c00000007ab5d550 GPR28: c00000007ab5c000 c000000032fcf848 c00000007ab5cc00 c000000032fcf800 NIP [c0000000000c1a30] memset+0x68/0x104 LR [c008000001b00c18] ibmvnic_reset_crq+0x70/0x110 [ibmvnic] Call Trace: [c00000000d05ba30] [0000000000000800] 0x800 (unreliable) [c00000000d05bab0] [c008000001b0a930] do_reset.isra.40+0x224/0x634 [ibmvnic] [c00000000d05bb80] [c008000001b08574] __ibmvnic_reset+0x17c/0x3c0 [ibmvnic] [c00000000d05bc50] [c00000000018d9ac] process_one_work+0x2cc/0x800 [c00000000d05bd20] [c00000000018df58] worker_thread+0x78/0x520 [c00000000d05bdb0] [c00000000019a934] kthread+0x1c4/0x1d0 [c00000000d05be20] [c00000000000d5d0] ret_from_kernel_thread+0x5c/0x6c Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol") Signed-off-by: Lijun Pan <ljp@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * ibmvnic: fix NULL pointer dereference in reset_sub_crq_queuesLijun Pan2020-11-241-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | adapter->tx_scrq and adapter->rx_scrq could be NULL if the previous reset did not complete after freeing sub crqs. Check for NULL before dereferencing them. Snippet of call trace: ibmvnic 30000006 env6: Releasing sub-CRQ ibmvnic 30000006 env6: Releasing CRQ ... ibmvnic 30000006 env6: Got Control IP offload Response ibmvnic 30000006 env6: Re-setting tx_scrq[0] BUG: Kernel NULL pointer dereference on read at 0x00000000 Faulting instruction address: 0xc008000003dea7cc Oops: Kernel access of bad area, sig: 11 [#1] LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries Modules linked in: rpadlpar_io rpaphp xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables xsk_diag tcp_diag udp_diag raw_diag inet_diag unix_diag af_packet_diag netlink_diag tun bridge stp llc rfkill sunrpc pseries_rng xts vmx_crypto uio_pdrv_genirq uio binfmt_misc ip_tables xfs libcrc32c sd_mod t10_pi sg ibmvscsi ibmvnic ibmveth scsi_transport_srp dm_mirror dm_region_hash dm_log dm_mod CPU: 80 PID: 1856 Comm: kworker/80:2 Tainted: G W 5.8.0+ #4 Workqueue: events __ibmvnic_reset [ibmvnic] NIP: c008000003dea7cc LR: c008000003dea7bc CTR: 0000000000000000 REGS: c0000007ef7db860 TRAP: 0380 Tainted: G W (5.8.0+) MSR: 800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 28002422 XER: 0000000d CFAR: c000000000bd9520 IRQMASK: 0 GPR00: c008000003dea7bc c0000007ef7dbaf0 c008000003df7400 c0000007fa26ec00 GPR04: c0000007fcd0d008 c0000007fcd96350 0000000000000027 c0000007fcd0d010 GPR08: 0000000000000023 0000000000000000 0000000000000000 0000000000000000 GPR12: 0000000000002000 c00000001ec18e00 c0000000001982f8 c0000007bad6e840 GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR20: 0000000000000000 0000000000000000 0000000000000000 fffffffffffffef7 GPR24: 0000000000000402 c0000007fa26f3a8 0000000000000003 c00000016f8ec048 GPR28: 0000000000000000 0000000000000000 0000000000000000 c0000007fa26ec00 NIP [c008000003dea7cc] ibmvnic_reset_init+0x15c/0x258 [ibmvnic] LR [c008000003dea7bc] ibmvnic_reset_init+0x14c/0x258 [ibmvnic] Call Trace: [c0000007ef7dbaf0] [c008000003dea7bc] ibmvnic_reset_init+0x14c/0x258 [ibmvnic] (unreliable) [c0000007ef7dbb80] [c008000003de8860] __ibmvnic_reset+0x408/0x970 [ibmvnic] [c0000007ef7dbc50] [c00000000018b7cc] process_one_work+0x2cc/0x800 [c0000007ef7dbd20] [c00000000018bd78] worker_thread+0x78/0x520 [c0000007ef7dbdb0] [c0000000001984c4] kthread+0x1d4/0x1e0 [c0000007ef7dbe20] [c00000000000cea8] ret_from_kernel_thread+0x5c/0x74 Fixes: 57a49436f4e8 ("ibmvnic: Reset sub-crqs during driver reset") Signed-off-by: Lijun Pan <ljp@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: ena: fix packet's addresses for rx_offset featureShay Agroskin2020-11-241-9/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes two lines in which the rx_offset received by the device wasn't taken into account: - prefetch function: In our driver the copied data would reside in rx_info->page + rx_headroom + rx_offset so the prefetch function is changed accordingly. - setting page_offset to zero for descriptors > 1: for every descriptor but the first, the rx_offset is zero. Hence the page_offset value should be set to rx_headroom. The previous implementation changed the value of rx_info after the descriptor was added to the SKB (essentially providing wrong page offset). Fixes: 68f236df93a9 ("net: ena: add support for the rx offset feature") Signed-off-by: Shay Agroskin <shayagr@amazon.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: ena: set initial DMA width to avoid intel iommu issueShay Agroskin2020-11-241-9/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ENA driver uses the readless mechanism, which uses DMA, to find out what the DMA mask is supposed to be. If DMA is used without setting the dma_mask first, it causes the Intel IOMMU driver to think that ENA is a 32-bit device and therefore disables IOMMU passthrough permanently. This patch sets the dma_mask to be ENA_MAX_PHYS_ADDR_SIZE_BITS=48 before readless initialization in ena_device_init()->ena_com_mmio_reg_read_request_init(), which is large enough to workaround the intel_iommu issue. DMA mask is set again to the correct value after it's received from the device after readless is initialized. The patch also changes the driver to use dma_set_mask_and_coherent() function instead of the two pci_set_dma_mask() and pci_set_consistent_dma_mask() ones. Both methods achieve the same effect. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Mike Cui <mikecui@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: Shay Agroskin <shayagr@amazon.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: ena: handle bad request id in ena_netdevShay Agroskin2020-11-242-32/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After request id is checked in validate_rx_req_id() its value is still used in the line rx_ring->free_ids[next_to_clean] = rx_ring->ena_bufs[i].req_id; even if it was found to be out-of-bound for the array free_ids. The patch moves the request id to an earlier stage in the napi routine and makes sure its value isn't used if it's found out-of-bounds. Fixes: 30623e1ed116 ("net: ena: avoid memory access violation by validating req_id properly") Signed-off-by: Ido Segev <idose@amazon.com> Signed-off-by: Shay Agroskin <shayagr@amazon.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * nfc: s3fwrn5: use signed integer for parsing GPIO numbersKrzysztof Kozlowski2020-11-241-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | GPIOs - as returned by of_get_named_gpio() and used by the gpiolib - are signed integers, where negative number indicates error. The return value of of_get_named_gpio() should not be assigned to an unsigned int because in case of !CONFIG_GPIOLIB such number would be a valid GPIO. Fixes: c04c674fadeb ("nfc: s3fwrn5: Add driver for Samsung S3FWRN5 NFC Chip") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20201123162351.209100-1-krzk@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * dpaa2-eth: Fix compile error due to missing devlink supportEzequiel Garcia2020-11-241-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The dpaa2 driver depends on devlink, so it should select NET_DEVLINK in order to fix compile errors, such as: drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.o: in function `dpaa2_eth_rx_err': dpaa2-eth.c:(.text+0x3cec): undefined reference to `devlink_trap_report' drivers/net/ethernet/freescale/dpaa2/dpaa2-eth-devlink.o: in function `dpaa2_eth_dl_info_get': dpaa2-eth-devlink.c:(.text+0x160): undefined reference to `devlink_info_driver_name_put' Fixes: ceeb03ad8e22 ("dpaa2-eth: add basic devlink support") Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Link: https://lore.kernel.org/r/20201123163553.1666476-1-ciorneiioana@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * aquantia: Remove the build_skb pathLincoln Ramsay2020-11-241-74/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When performing IPv6 forwarding, there is an expectation that SKBs will have some headroom. When forwarding a packet from the aquantia driver, this does not always happen, triggering a kernel warning. aq_ring.c has this code (edited slightly for brevity): if (buff->is_eop && buff->len <= AQ_CFG_RX_FRAME_MAX - AQ_SKB_ALIGN) { skb = build_skb(aq_buf_vaddr(&buff->rxdata), AQ_CFG_RX_FRAME_MAX); } else { skb = napi_alloc_skb(napi, AQ_CFG_RX_HDR_SIZE); There is a significant difference between the SKB produced by these 2 code paths. When napi_alloc_skb creates an SKB, there is a certain amount of headroom reserved. However, this is not done in the build_skb codepath. As the hardware buffer that build_skb is built around does not handle the presence of the SKB header, this code path is being removed and the napi_alloc_skb path will always be used. This code path does have to copy the packet header into the SKB, but it adds the packet data as a frag. Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Signed-off-by: Lincoln Ramsay <lincoln.ramsay@opengear.com> Link: https://lore.kernel.org/r/MWHPR1001MB23184F3EAFA413E0D1910EC9E8FC0@MWHPR1001MB2318.namprd10.prod.outlook.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * i40e: Fix removing driver while bare-metal VFs pass trafficSylwester Dziedziuch2020-11-233-18/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Prevent VFs from resetting when PF driver is being unloaded: - introduce new pf state: __I40E_VF_RESETS_DISABLED; - check if pf state has __I40E_VF_RESETS_DISABLED state set, if so, disable any further VFLR event notifications; - when i40e_remove (rmmod i40e) is called, disable any resets on the VFs; Previously if there were bare-metal VFs passing traffic and PF driver was removed, there was a possibility of VFs triggering a Tx timeout right before iavf_remove. This was causing iavf_close to not be called because there is a check in the beginning of iavf_remove that bails out early if adapter->state < IAVF_DOWN_PENDING. This makes it so some resources do not get cleaned up. Fixes: 6a9ddb36eeb8 ("i40e: disable IOV before freeing resources") Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20201120180640.3654474-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * Merge tag 'wireless-drivers-2020-11-23' of ↵Jakub Kicinski2020-11-239-53/+159
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for v5.10 First set of fixes for v5.10. One fix for iwlwifi kernel panic, others less notable. rtw88 * fix a bogus test found by clang iwlwifi * fix long memory reads causing soft lockup warnings * fix kernel panic during Channel Switch Announcement (CSA) * other smaller fixes MAINTAINERS * email address updates * tag 'wireless-drivers-2020-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers: iwlwifi: mvm: fix kernel panic in case of assert during CSA iwlwifi: pcie: set LTR to avoid completion timeout iwlwifi: mvm: write queue_sync_state only for sync iwlwifi: mvm: properly cancel a session protection for P2P iwlwifi: mvm: use the HOT_SPOT_CMD to cancel an AUX ROC iwlwifi: sta: set max HE max A-MPDU according to HE capa MAINTAINERS: update maintainers list for Cypress MAINTAINERS: update Yan-Hsuan's email address iwlwifi: pcie: limit memory read spin time rtw88: fix fw_fifo_addr check ==================== Link: https://lore.kernel.org/r/20201123161037.C11D1C43460@smtp.codeaurora.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| | * iwlwifi: mvm: fix kernel panic in case of assert during CSASara Sharon2020-11-101-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | During CSA, we briefly nullify the phy context, in __iwl_mvm_unassign_vif_chanctx. In case we have a FW assert right after it, it remains NULL though. We end up running into endless loop due to mac80211 trying repeatedly to move us to ASSOC state, and we keep returning -EINVAL. Later down the road we hit a kernel panic. Detect and avoid this endless loop. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20201107104557.d64de2c17bff.Iedd0d2afa20a2aacba5259a5cae31cb3a119a4eb@changeid
| | * iwlwifi: pcie: set LTR to avoid completion timeoutJohannes Berg2020-11-102-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On some platforms, the preset values aren't correct and then we may get a completion timeout in the firmware. Change the LTR configuration to avoid that. The firmware will do some more complex reinit of this later, but for the boot process we use ~250usec. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20201107104557.d83d591c05ba.I42885c9fb500bc08b9a4c07c4ff3d436cc7a3c84@changeid
| | * iwlwifi: mvm: write queue_sync_state only for syncAvraham Stern2020-11-101-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We use mvm->queue_sync_state to wait for synchronous queue sync messages, but if an async one happens inbetween we shouldn't clear mvm->queue_sync_state after sending the async one, that can run concurrently (at least from the CPU POV) with another synchronous queue sync. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Fixes: 3c514bf831ac ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20201107104557.51a3148f2c14.I0772171dbaec87433a11513e9586d98b5d920b5f@changeid
| | * iwlwifi: mvm: properly cancel a session protection for P2PEmmanuel Grumbach2020-11-102-34/+68
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We need to feed the configuration id to remove session protection properly. Remember the conf_id when we add the session protection so that we can give it back when we want to remove the session protection. While at it, slightly improve the kernel doc for the conf_id of the notification. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Fixes: fe959c7b2049 ("iwlwifi: mvm: use the new session protection command") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20201107104557.3642f730333d.I01a98ecde62096d00d171cf34ad775bf80cb0277@changeid
| | * iwlwifi: mvm: use the HOT_SPOT_CMD to cancel an AUX ROCEmmanuel Grumbach2020-11-101-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ROC that runs on the AUX ROC (meaning an ROC on the STA vif), was added with the HOT_SPOT_CMD firmware command and must be cancelled with that same command. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Fixes: fe959c7b2049 ("iwlwifi: mvm: use the new session protection command") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20201107104557.a317376154da.I44fa3637373ba4bd421cdff2cabc761bffc0735f@changeid
| | * iwlwifi: sta: set max HE max A-MPDU according to HE capaMordechay Goodstein2020-11-102-5/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, our max tpt is limited to max HT A-MPDU for LB, and max VHT A-MPDU for HB. Configure HE exponent value correctly to achieve HE max A-MPDU, both on LB and HB. Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20201107104557.4486852ebb56.I9eb0d028e31f183597fb90120e7d4ca87e0dd6cb@changeid
| | * iwlwifi: pcie: limit memory read spin timeJohannes Berg2020-11-021-9/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When we read device memory, we lock a spinlock, write the address we want to read from the device and then spin in a loop reading the data in 32-bit quantities from another register. As the description makes clear, this is rather inefficient, incurring a PCIe bus transaction for every read. In a typical device today, we want to read 786k SMEM if it crashes, leading to 192k register reads. Occasionally, we've seen the whole loop take over 20 seconds and then triggering the soft lockup detector. Clearly, it is unreasonable to spin here for such extended periods of time. To fix this, break the loop down into an outer and an inner loop, and break out of the inner loop if more than half a second elapsed. To avoid too much overhead, check for that only every 128 reads, though there's no particular reason for that number. Then, unlock and relock to obtain NIC access again, reprogram the start address and continue. This will keep (interrupt) latencies on the CPU down to a reasonable time. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20201022165103.45878a7e49aa.I3b9b9c5a10002915072312ce75b68ed5b3dc6e14@changeid
| | * rtw88: fix fw_fifo_addr checkTom Rix2020-11-021-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The clang build reports this warning fw.c:1485:21: warning: address of array 'rtwdev->chip->fw_fifo_addr' will always evaluate to 'true' if (!rtwdev->chip->fw_fifo_addr) { fw_fifo_addr is an array in rtw_chip_info so it is always nonzero. A better check is if the first element of the array is nonzero. In the cases where fw_fifo_addr is initialized by rtw88b and rtw88c, the first array element is 0x780. Fixes: 0fbc2f0f34cc ("rtw88: add dump firmware fifo support") Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201011155438.15892-1-trix@redhat.com
| * | ibmvnic: skip tx timeout reset while in resettingLijun Pan2020-11-211-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sometimes it takes longer than 5 seconds (watchdog timeout) to complete failover, migration, and other resets. In stead of scheduling another timeout reset, we wait for the current one to complete. Suggested-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Lijun Pan <ljp@linux.ibm.com> Reviewed-by: Dany Madden <drt@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | ibmvnic: notify peers when failover and migration happenLijun Pan2020-11-211-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 61d3e1d9bc2a ("ibmvnic: Remove netdev notify for failover resets") excluded the failover case for notify call because it said netdev_notify_peers() can cause network traffic to stall or halt. Current testing does not show network traffic stall or halt because of the notify call for failover event. netdev_notify_peers may be used when a device wants to inform the rest of the network about some sort of a reconfiguration such as failover or migration. It is unnecessary to call that in other events like FATAL, NON_FATAL, CHANGE_PARAM, and TIMEOUT resets since in those scenarios the hardware does not change. If the driver must do a hard reset, it is necessary to notify peers. Fixes: 61d3e1d9bc2a ("ibmvnic: Remove netdev notify for failover resets") Suggested-by: Brian King <brking@linux.vnet.ibm.com> Suggested-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com> Signed-off-by: Dany Madden <drt@linux.ibm.com> Signed-off-by: Lijun Pan <ljp@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | ibmvnic: fix call_netdevice_notifiers in do_resetLijun Pan2020-11-211-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When netdev_notify_peers was substituted in commit 986103e7920c ("net/ibmvnic: Fix RTNL deadlock during device reset"), call_netdevice_notifiers(NETDEV_RESEND_IGMP, dev) was missed. Fix it now. Fixes: 986103e7920c ("net/ibmvnic: Fix RTNL deadlock during device reset") Signed-off-by: Lijun Pan <ljp@linux.ibm.com> Reviewed-by: Dany Madden <drt@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | tun: honor IOCB_NOWAIT flagJens Axboe2020-11-211-3/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | tun only checks the file O_NONBLOCK flag, but it should also be checking the iocb IOCB_NOWAIT flag. Any fops using ->read/write_iter() should check both, otherwise it breaks users that correctly expect O_NONBLOCK semantics if IOCB_NOWAIT is set. Signed-off-by: Jens Axboe <axboe@kernel.dk> Link: https://lore.kernel.org/r/e9451860-96cc-c7c7-47b8-fe42cadd5f4c@kernel.dk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | usbnet: ipheth: fix connectivity with iOS 14Yves-Alexis Perez2020-11-211-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Starting with iOS 14 released in September 2020, connectivity using the personal hotspot USB tethering function of iOS devices is broken. Communication between the host and the device (for example ICMP traffic or DNS resolution using the DNS service running in the device itself) works fine, but communication to endpoints further away doesn't work. Investigation on the matter shows that no UDP and ICMP traffic from the tethered host is reaching the Internet at all. For TCP traffic there are exchanges between tethered host and server but packets are modified in transit leading to impossible communication. After some trials Matti Vuorela discovered that reducing the URB buffer size by two bytes restored the previous behavior. While a better solution might exist to fix the issue, since the protocol is not publicly documented and considering the small size of the fix, let's do that. Tested-by: Matti Vuorela <matti.vuorela@bitfactor.fi> Signed-off-by: Yves-Alexis Perez <corsac@corsac.net> Link: https://lore.kernel.org/linux-usb/CAAn0qaXmysJ9vx3ZEMkViv_B19ju-_ExN8Yn_uSefxpjS6g4Lw@mail.gmail.com/ Link: https://github.com/libimobiledevice/libimobiledevice/issues/1038 Link: https://lore.kernel.org/r/20201119172439.94988-1-corsac@corsac.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | cxgb4: Fix build failure when CONFIG_TLS=mTom Seewald2020-11-211-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After commit 9d2e5e9eeb59 ("cxgb4/ch_ktls: decrypted bit is not enough") whenever CONFIG_TLS=m and CONFIG_CHELSIO_T4=y, the following build failure occurs: ld: drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.o: in function `cxgb_select_queue': cxgb4_main.c:(.text+0x2dac): undefined reference to `tls_validate_xmit_skb' Fix this by ensuring that if TLS is set to be a module, CHELSIO_T4 will also be compiled as a module. As otherwise the cxgb4 driver will not be able to access TLS' symbols. Fixes: 9d2e5e9eeb59 ("cxgb4/ch_ktls: decrypted bit is not enough") Signed-off-by: Tom Seewald <tseewald@gmail.com> Link: https://lore.kernel.org/r/20201120192528.615-1-tseewald@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | bonding: wait for sysfs kobject destruction before freeing struct slaveJamie Iles2020-11-212-35/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | syzkaller found that with CONFIG_DEBUG_KOBJECT_RELEASE=y, releasing a struct slave device could result in the following splat: kobject: 'bonding_slave' (00000000cecdd4fe): kobject_release, parent 0000000074ceb2b2 (delayed 1000) bond0 (unregistering): (slave bond_slave_1): Releasing backup interface ------------[ cut here ]------------ ODEBUG: free active (active state 0) object type: timer_list hint: workqueue_select_cpu_near kernel/workqueue.c:1549 [inline] ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x98 kernel/workqueue.c:1600 WARNING: CPU: 1 PID: 842 at lib/debugobjects.c:485 debug_print_object+0x180/0x240 lib/debugobjects.c:485 Kernel panic - not syncing: panic_on_warn set ... CPU: 1 PID: 842 Comm: kworker/u4:4 Tainted: G S 5.9.0-rc8+ #96 Hardware name: linux,dummy-virt (DT) Workqueue: netns cleanup_net Call trace: dump_backtrace+0x0/0x4d8 include/linux/bitmap.h:239 show_stack+0x34/0x48 arch/arm64/kernel/traps.c:142 __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x174/0x1f8 lib/dump_stack.c:118 panic+0x360/0x7a0 kernel/panic.c:231 __warn+0x244/0x2ec kernel/panic.c:600 report_bug+0x240/0x398 lib/bug.c:198 bug_handler+0x50/0xc0 arch/arm64/kernel/traps.c:974 call_break_hook+0x160/0x1d8 arch/arm64/kernel/debug-monitors.c:322 brk_handler+0x30/0xc0 arch/arm64/kernel/debug-monitors.c:329 do_debug_exception+0x184/0x340 arch/arm64/mm/fault.c:864 el1_dbg+0x48/0xb0 arch/arm64/kernel/entry-common.c:65 el1_sync_handler+0x170/0x1c8 arch/arm64/kernel/entry-common.c:93 el1_sync+0x80/0x100 arch/arm64/kernel/entry.S:594 debug_print_object+0x180/0x240 lib/debugobjects.c:485 __debug_check_no_obj_freed lib/debugobjects.c:967 [inline] debug_check_no_obj_freed+0x200/0x430 lib/debugobjects.c:998 slab_free_hook mm/slub.c:1536 [inline] slab_free_freelist_hook+0x190/0x210 mm/slub.c:1577 slab_free mm/slub.c:3138 [inline] kfree+0x13c/0x460 mm/slub.c:4119 bond_free_slave+0x8c/0xf8 drivers/net/bonding/bond_main.c:1492 __bond_release_one+0xe0c/0xec8 drivers/net/bonding/bond_main.c:2190 bond_slave_netdev_event drivers/net/bonding/bond_main.c:3309 [inline] bond_netdev_event+0x8f0/0xa70 drivers/net/bonding/bond_main.c:3420 notifier_call_chain+0xf0/0x200 kernel/notifier.c:83 __raw_notifier_call_chain kernel/notifier.c:361 [inline] raw_notifier_call_chain+0x44/0x58 kernel/notifier.c:368 call_netdevice_notifiers_info+0xbc/0x150 net/core/dev.c:2033 call_netdevice_notifiers_extack net/core/dev.c:2045 [inline] call_netdevice_notifiers net/core/dev.c:2059 [inline] rollback_registered_many+0x6a4/0xec0 net/core/dev.c:9347 unregister_netdevice_many.part.0+0x2c/0x1c0 net/core/dev.c:10509 unregister_netdevice_many net/core/dev.c:10508 [inline] default_device_exit_batch+0x294/0x338 net/core/dev.c:10992 ops_exit_list.isra.0+0xec/0x150 net/core/net_namespace.c:189 cleanup_net+0x44c/0x888 net/core/net_namespace.c:603 process_one_work+0x96c/0x18c0 kernel/workqueue.c:2269 worker_thread+0x3f0/0xc30 kernel/workqueue.c:2415 kthread+0x390/0x498 kernel/kthread.c:292 ret_from_fork+0x10/0x18 arch/arm64/kernel/entry.S:925 This is a potential use-after-free if the sysfs nodes are being accessed whilst removing the struct slave, so wait for the object destruction to complete before freeing the struct slave itself. Fixes: 07699f9a7c8d ("bonding: add sysfs /slave dir for bond slave devices.") Fixes: a068aab42258 ("bonding: Fix reference count leak in bond_sysfs_slave_add.") Cc: Qiushi Wu <wu000273@umn.edu> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Jamie Iles <jamie@nuviainc.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20201120142827.879226-1-jamie@nuviainc.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | s390/qeth: fix tear down of async TX buffersJulian Wiedmann2020-11-201-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When qeth_iqd_tx_complete() detects that a TX buffer requires additional async completion via QAOB, it might fail to replace the queue entry's metadata (and ends up triggering recovery). Assume now that the device gets torn down, overruling the recovery. If the QAOB notification then arrives before the tear down has sufficiently progressed, the buffer state is changed to QETH_QDIO_BUF_HANDLED_DELAYED by qeth_qdio_handle_aob(). The tear down code calls qeth_drain_output_queue(), where qeth_cleanup_handled_pending() will then attempt to replace such a buffer _again_. If it succeeds this time, the buffer ends up dangling in its replacement's ->next_pending list ... where it will never be freed, since there's no further call to qeth_cleanup_handled_pending(). But the second attempt isn't actually needed, we can simply leave the buffer on the queue and re-use it after a potential recovery has completed. The qeth_clear_output_buffer() in qeth_drain_output_queue() will ensure that it's in a clean state again. Fixes: 72861ae792c2 ("qeth: recovery through asynchronous delivery") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | s390/qeth: fix af_iucv notification raceJulian Wiedmann2020-11-202-24/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The two expected notification sequences are 1. TX_NOTIFY_PENDING with a subsequent TX_NOTIFY_DELAYED_*, when our TX completion code first observed the pending TX and the QAOB then completes at a later time; or 2. TX_NOTIFY_OK, when qeth_qdio_handle_aob() picked up the QAOB completion before our TX completion code even noticed that the TX was pending. But as qeth_iqd_tx_complete() and qeth_qdio_handle_aob() can run concurrently, we may end up with a race that results in a sequence of TX_NOTIFY_DELAYED_* followed by TX_NOTIFY_PENDING. Which would confuse the af_iucv code in its tracking of pending transmits. Rework the notification code, so that qeth_qdio_handle_aob() defers its notification if the TX completion code is still active. Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | s390/qeth: make af_iucv TX notification call more robustJulian Wiedmann2020-11-201-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Calling into socket code is ugly already, at least check whether we are dealing with the expected sk_family. Only looking at skb->protocol is bound to cause troubles (consider eg. af_packet). Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | s390/qeth: Remove pnso workaroundAlexandra Winter2020-11-201-16/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove workaround that supported early hardware implementations of PNSO OC3. Rely on the 'enarf' feature bit instead. Fixes: fa115adff2c1 ("s390/qeth: Detect PNSO OC3 capability") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com> [jwi: use logical instead of bit-wise AND] Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | dpaa2-eth: select XGMAC_MDIO for MDIO bus supportIoana Ciornei2020-11-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Explicitly enable the FSL_XGMAC_MDIO Kconfig option in order to have MDIO access to internal and external PHYs. Fixes: 719479230893 ("dpaa2-eth: add MAC/PHY support through phylink") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Link: https://lore.kernel.org/r/20201119145106.712761-1-ciorneiioana@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | cxgb4: fix the panic caused by non smac rewriteRaju Rangoju2020-11-201-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SMT entry is allocated only when loopback Source MAC rewriting is requested. Accessing SMT entry for non smac rewrite cases results in kernel panic. Fix the panic caused by non smac rewrite Fixes: 937d84205884 ("cxgb4: set up filter action after rewrites") Signed-off-by: Raju Rangoju <rajur@chelsio.com> Link: https://lore.kernel.org/r/20201118143213.13319-1-rajur@chelsio.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | bnxt_en: Release PCI regions when DMA mask setup fails during probe.Michael Chan2020-11-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Jump to init_err_release to cleanup. bnxt_unmap_bars() will also be called but it will do nothing if the BARs are not mapped yet. Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reported-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/1605858271-8209-1-git-send-email-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | bnxt_en: fix error return code in bnxt_init_board()Zhang Changzhong2020-11-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Link: https://lore.kernel.org/r/1605792621-6268-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | bnxt_en: fix error return code in bnxt_init_one()Zhang Changzhong2020-11-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: c213eae8d3cd ("bnxt_en: Improve VF/PF link change logic.") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Link: https://lore.kernel.org/r/1605701851-20270-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | | Merge tag 'scsi-fixes' of ↵Linus Torvalds2020-11-271-14/+23
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "Three small fixes in the UFS driver: two are for power management issues and the third is to fix a slew of problem in the sysfs code" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: ufs: Fix race between shutdown and runtime resume flow scsi: ufs: Make sure clk scaling happens only when HBA is runtime ACTIVE scsi: ufs: Fix unexpected values from ufshcd_read_desc_param()
| * | | scsi: ufs: Fix race between shutdown and runtime resume flowStanley Chu2020-11-191-5/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If UFS host device is in runtime-suspended state while UFS shutdown callback is invoked, UFS device shall be resumed for register accesses. Currently only UFS local runtime resume function will be invoked to wake up the host. This is not enough because if someone triggers runtime resume from block layer, then race may happen between shutdown and runtime resume flow, and finally lead to unlocked register access. To fix this, in ufshcd_shutdown(), use pm_runtime_get_sync() instead of resuming UFS device by ufshcd_runtime_resume() "internally" to let runtime PM framework manage the whole resume flow. Link: https://lore.kernel.org/r/20201119062916.12931-1-stanley.chu@mediatek.com Fixes: 57d104c153d3 ("ufs: add UFS power management support") Reviewed-by: Can Guo <cang@codeaurora.org> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * | | scsi: ufs: Make sure clk scaling happens only when HBA is runtime ACTIVECan Guo2020-11-181-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If someone plays with the UFS clk scaling devfreq governor through sysfs, ufshcd_devfreq_scale may be called even when HBA is not runtime ACTIVE. This can lead to unexpected error. We cannot just protect it by calling pm_runtime_get_sync() because that may cause a race condition since HBA runtime suspend ops need to suspend clk scaling. To fix this call pm_runtime_get_noresume() and check HBA's runtime status. Only proceed if HBA is runtime ACTIVE, otherwise just bail. governor_store devfreq_performance_handler update_devfreq devfreq_set_target ufshcd_devfreq_target ufshcd_devfreq_scale Link: https://lore.kernel.org/r/1600758548-28576-1-git-send-email-cang@codeaurora.org Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * | | scsi: ufs: Fix unexpected values from ufshcd_read_desc_param()Can Guo2020-11-181-9/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WB-related sysfs entries can be accessed even when an UFS device does not support the feature. The descriptors which are not supported by the UFS device may be wrongly reported when they are accessed from their corrsponding sysfs entries. Fix it by adding a sanity check of parameter offset against the actual decriptor length. Link: https://lore.kernel.org/r/1603346348-14149-1-git-send-email-cang@codeaurora.org Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Acked-by: Daejun Park <daejun7.park@samsung.com> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* | | | Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdmaLinus Torvalds2020-11-2713-93/+98
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull rdma fixes from Jason Gunthorpe: "Two security issues and several small bug fixes. Things seem to have stabilized for this release here. Summary: - Significant out of bounds access security issue in i40iw - Fix misuse of mmu notifiers in hfi1 - Several errors in the register map/usage in hns - Missing error returns in mthca" * tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: RDMA/hns: Bugfix for memory window mtpt configuration RDMA/hns: Fix retry_cnt and rnr_cnt when querying QP RDMA/hns: Fix wrong field of SRQ number the device supports IB/hfi1: Ensure correct mm is used at all times RDMA/i40iw: Address an mmap handler exploit in i40iw IB/mthca: fix return value of error branch in mthca_init_cq()
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-15 03:55:50 +0000