summaryrefslogtreecommitdiffstats
path: root/drivers
Commit message (Collapse)AuthorAgeFilesLines
* USB: gadget: udc: Add missing platform_device_put() on error in bdc_pci_probe()Wei Yongjun2018-02-151-0/+1
| | | | | | | | | Add the missing platform_device_put() before return from bdc_pci_probe() in the platform_device_add_resources() error handling case. Fixes: efed421a94e6 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Fix dwc2_hsotg_core_init_disconnected()Vardan Mikayelyan2018-02-121-6/+6
| | | | | | | | | | | | | | | We should call dwc2_hsotg_enqueue_setup() after properly setting lx_state. Because it may cause error-out from dwc2_hsotg_enqueue_setup() due to wrong value in lx_state. Issue can be reproduced by loading driver while connected A-Connector (start in A-HOST mode) then disconnect A-Connector to switch to B-DEVICE. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Add safety check for STSPHSERCVD intrMinas Harutyunyan2018-02-121-3/+7
| | | | | | | | | | | | | STSPHSERCVD (status phase received) interrupt should be handled when EP0 is in DWC2_EP0_DATA_OUT state. Sometimes STSPHSERCVD interrupt asserted , when EP0 is not in DATA_OUT state. Spurios interrupt. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Minas Harutyunyan <hminas@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Add safety check in setting of descriptor chain pointersMinas Harutyunyan2018-02-121-1/+3
| | | | | | | | | | | | | | | | | In some cases device sending ZLP IN on non EP0 which reassigning EP0 OUT descriptor pointer to that EP. Dedicated for EP0 OUT descriptor multiple time re-used by other EP while that descriptor already in use by EP0 OUT for SETUP transaction. As result when SETUP packet received BNA interrupt asserting. In dwc2_hsotg_program_zlp() function dwc2_gadget_set_ep0_desc_chain() must be called only for EP0. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Minas Harutyunyan <hminas@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: gadget: fsl_udc_core: fix ep valid checksStefan Agner2018-02-121-2/+2
| | | | | | | | | | | | | | | Clang reports the following warning: drivers/usb/gadget/udc/fsl_udc_core.c:1312:10: warning: address of array 'ep->name' will always evaluate to 'true' [-Wpointer-bool-conversion] if (ep->name) ~~ ~~~~^~~~ It seems that the authors intention was to check if the ep has been configured through struct_ep_setup. Check whether struct usb_ep name pointer has been set instead. Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: renesas_usbhs: missed the "running" flag in usb_dmac with rx pathYoshihiro Shimoda2018-02-121-0/+5
| | | | | | | | | | | | | | | | This fixes an issue that a gadget driver (usb_f_fs) is possible to stop rx transactions after the usb-dmac is used because the following functions missed to set/check the "running" flag. - usbhsf_dma_prepare_pop_with_usb_dmac() - usbhsf_dma_pop_done_with_usb_dmac() So, if next transaction uses pio, the usbhsf_prepare_pop() can not start the transaction because the "running" flag is 0. Fixes: 8355b2b3082d ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle") Cc: <stable@vger.kernel.org> # v3.19+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: gadget: udc: Remove USB_GADGET_DUALSPEED selectUlf Magnusson2018-02-121-1/+0
| | | | | | | | | | | | | | | USB_GADGET_DUALSPEED was removed by commit 85b8614d7223 ("usb: gadget: get rid of USB_GADGET_{DUAL,SUPER}SPEED"), but the USB_SNP_UDC_PLAT symbol still selects it. Remove the USB_GADGET_DUALSPEED select from USB_SNP_UDC_PLAT. Discovered with the https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py script. Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc3: Fix GDBGFIFOSPACE_TYPE valuesThinh Nguyen2018-02-121-7/+9
| | | | | | | | | | | The FIFO/Queue type values are incorrect. Correct them according to DWC_usb3 programming guide section 1.2.27 (or DWC_usb31 section 1.2.25). Additionally, this patch includes ProtocolStatusQ and AuxEventQ types. Fixes: cf6d867d3b57 ("usb: dwc3: core: add fifo space helper") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: gadget: core: Fix use-after-free of usb_requestManu Gautam2018-02-121-1/+1
| | | | | | | | Driver is tracing usb_request after freeing it. Fix it by changing the order. Signed-off-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc3: omap: don't miss events during suspend/resumeRoger Quadros2018-02-121-0/+16
| | | | | | | | The USB cable state can change during suspend/resume so be sure to check and update the extcon state. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: gadget: f_fs: Use config_ep_by_speed()Jack Pham2018-02-121-31/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | In commit 2bfa0719ac2a ("usb: gadget: function: f_fs: pass companion descriptor along") there is a pointer arithmetic bug where the comp_desc is obtained as follows: comp_desc = (struct usb_ss_ep_comp_descriptor *)(ds + USB_DT_ENDPOINT_SIZE); Since ds is a pointer to usb_endpoint_descriptor, adding 7 to it ends up going out of bounds (7 * sizeof(struct usb_endpoint_descriptor), which is actually 7*9 bytes) past the SS descriptor. As a result the maxburst value will be read incorrectly, and the UDC driver will also get a garbage comp_desc (assuming it uses it). Since Felipe wrote, "Eventually, f_fs.c should be converted to use config_ep_by_speed() like all other functions, though", let's finally do it. This allows the other usb_ep fields to be properly populated, such as maxpacket and mult. It also eliminates the awkward speed-based descriptor lookup since config_ep_by_speed() does that already using the ones found in struct usb_function. Fixes: 2bfa0719ac2a ("usb: gadget: function: f_fs: pass companion descriptor along") Cc: stable@vger.kernel.org Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: gadget: f_fs: Process all descriptors during bindJack Pham2018-02-121-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | During _ffs_func_bind(), the received descriptors are evaluated to prepare for binding with the gadget in order to allocate endpoints and optionally set up OS descriptors. However, the high- and super-speed descriptors are only parsed based on whether the gadget_is_dualspeed() and gadget_is_superspeed() calls are true, respectively. This is a problem in case a userspace program always provides all of the {full,high,super,OS} descriptors when configuring a function. Then, for example if a gadget device is not capable of SuperSpeed, the call to ffs_do_descs() for the SS descriptors is skipped, resulting in an incorrect offset calculation for the vla_ptr when moving on to the OS descriptors that follow. This causes ffs_do_os_descs() to fail as it is now looking at the SS descriptors' offset within the raw_descs buffer instead. _ffs_func_bind() should evaluate the descriptors unconditionally, so remove the checks for gadget speed. Fixes: f0175ab51993 ("usb: gadget: f_fs: OS descriptors support") Cc: stable@vger.kernel.org Co-Developed-by: Mayank Rana <mrana@codeaurora.org> Signed-off-by: Mayank Rana <mrana@codeaurora.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: phy: mxs: Fix NULL pointer dereference on i.MX23/28Fabio Estevam2018-02-121-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit e93650994a95 ("usb: phy: mxs: add usb charger type detection") causes the following kernel hang on i.MX28: [ 2.207973] usbcore: registered new interface driver usb-storage [ 2.235659] Unable to handle kernel NULL pointer dereference at virtual address 00000188 [ 2.244195] pgd = (ptrval) [ 2.246994] [00000188] *pgd=00000000 [ 2.250676] Internal error: Oops: 5 [#1] ARM [ 2.254979] Modules linked in: [ 2.258089] CPU: 0 PID: 1 Comm: swapper Not tainted 4.15.0-rc8-next-20180117-00002-g75d5f21 #7 [ 2.266724] Hardware name: Freescale MXS (Device Tree) [ 2.271921] PC is at regmap_read+0x0/0x5c [ 2.275977] LR is at mxs_phy_charger_detect+0x34/0x1dc mxs_phy_charger_detect() makes accesses to the anatop registers via regmap, however i.MX23/28 do not have such registers, which causes a NULL pointer dereference. Fix the issue by doing a NULL check on the 'regmap' pointer. Fixes: e93650994a95 ("usb: phy: mxs: add usb charger type detection") Cc: <stable@vger.kernel.org> # v4.15 Reviewed-by: Li Jun <jun.li@nxp.com> Acked-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc3: core: Power-off core/PHYs on system_suspend in host modeManu Gautam2018-02-121-14/+22
| | | | | | | | | | | | | | | | | | | | | Commit 689bf72c6e0d ("usb: dwc3: Don't reinitialize core during host bus-suspend/resume") updated suspend/resume routines to not power_off and reinit PHYs/core for host mode. It broke platforms that rely on DWC3 core to power_off PHYs to enter low power state on system suspend. Perform dwc3_core_exit/init only during host mode system_suspend/ resume to addresses power regression from above mentioned patch and also allow USB session to stay connected across runtime_suspend/resume in host mode. While at it also replace existing checks for HOST only dr_mode with current_dr_role to have similar core driver behavior for both Host-only and DRD+Host configurations. Fixes: 689bf72c6e0d ("usb: dwc3: Don't reinitialize core during host bus-suspend/resume") Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc3: Undo PHY init if soft reset failsBrian Norris2018-02-121-0/+3
| | | | | | | | | | In this function, we init the USB2 and USB3 PHYs, but if soft reset times out, we don't unwind this. Noticed by inspection. Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: gadget: f_uac2: fix bFirstInterface in composite gadgetJohn Keeping2018-02-121-0/+2
| | | | | | | | | | | If there are multiple functions associated with a configuration, then the UAC2 interfaces may not start at zero. Set the correct first interface number in the association descriptor so that the audio interfaces are enumerated correctly in this case. Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by: John Keeping <john@metanate.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc3: ep0: Reset TRB counter for ep0 INThinh Nguyen2018-02-121-1/+6
| | | | | | | | | | | | | DWC3 tracks TRB counter for each ep0 direction separately. In control read transfer completion handler, the driver needs to reset the TRB enqueue counter for ep0 IN direction. Currently the driver only resets the TRB counter for control OUT endpoint. Check for the data direction and properly reset the TRB counter from correct control endpoint. Cc: stable@vger.kernel.org Fixes: c2da2ff00606 ("usb: dwc3: ep0: don't use ep0in for transfers") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc3: gadget: Set maxpacket size for ep0 INThinh Nguyen2018-02-121-0/+2
| | | | | | | | | | | | | | | | | | There are 2 control endpoint structures for DWC3. However, the driver only updates the OUT direction control endpoint structure during ConnectDone event. DWC3 driver needs to update the endpoint max packet size for control IN endpoint as well. If the max packet size is not properly set, then the driver will incorrectly calculate the data transfer size and fail to send ZLP for HS/FS 3-stage control read transfer. The fix is simply to update the max packet size for the ep0 IN direction during ConnectDone event. Cc: stable@vger.kernel.org Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: gadget: udc: renesas_usb3: fix oops in renesas_usb3_remove()Yoshihiro Shimoda2018-02-121-1/+1
| | | | | | | | | | This patch fixes an issue that the renesas_usb3_remove() causes NULL pointer dereference because the usb3_to_dev() macro will use the gadget instance and it will be deleted before. Fixes: cf06df3fae28 ("usb: gadget: udc: renesas_usb3: move pm_runtime_{en,dis}able()") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc3: of-simple: fix oops by unbalanced clk disable callEnric Balletbo i Serra2018-02-121-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | dwc3_of_simple_dev_pm_ops has never been used since commit a0d8c4cfdf31 ("usb: dwc3: of-simple: set dev_pm_ops"), but this commit has brought and oops when unbind the device due this sequence: dwc3_of_simple_remove -> clk_disable ... -> pm_runtime_put_sync -> dwc3_of_simple_runtime_suspend -> clk_disable (again) This double call to clk_core_disable causes a kernel oops like this: WARNING: CPU: 1 PID: 4022 at drivers/clk/clk.c:656 clk_core_disable+0x78/0x80 CPU: 1 PID: 4022 Comm: bash Not tainted 4.15.0-rc4+ #44 Hardware name: Google Kevin (DT) pstate: 80000085 (Nzcv daIf -PAN -UAO) pc : clk_core_disable+0x78/0x80 lr : clk_core_disable_lock+0x20/0x38 sp : ffff00000bbf3a90 ... Call trace: clk_core_disable+0x78/0x80 clk_disable+0x1c/0x30 dwc3_of_simple_runtime_suspend+0x30/0x50 pm_generic_runtime_suspend+0x28/0x40 This patch fixes the unbalanced clk disable call by setting the num_clocks variable to zero once the clocks were disabled. Fixes: a0d8c4cfdf31 ("usb: dwc3: of-simple: set dev_pm_ops") Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* vfs: do bulk POLL* -> EPOLL* replacementLinus Torvalds2018-02-11187-510/+510
| | | | | | | | | | | | | | | | | | | | | | | This is the mindless scripted replacement of kernel use of POLL* variables as described by Al, done by this script: for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'` for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done done with de-mangling cleanups yet to come. NOTE! On almost all architectures, the EPOLL* constants have the same values as the POLL* constants do. But they keyword here is "almost". For various bad reasons they aren't the same, and epoll() doesn't actually work quite correctly in some cases due to this on Sparc et al. The next patch from Al will sort out the final differences, and we should be all done. Scripted-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge branch 'work.poll2' of ↵Linus Torvalds2018-02-111-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull more poll annotation updates from Al Viro: "This is preparation to solving the problems you've mentioned in the original poll series. After this series, the kernel is ready for running for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'` for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done done as a for bulk search-and-replace. After that, the kernel is ready to apply the patch to unify {de,}mangle_poll(), and then get rid of kernel-side POLL... uses entirely, and we should be all done with that stuff. Basically, that's what you suggested wrt KPOLL..., except that we can use EPOLL... instead - they already are arch-independent (and equal to what is currently kernel-side POLL...). After the preparations (in this series) switch to returning EPOLL... from ->poll() instances is completely mechanical and kernel-side POLL... can go away. The last step (killing kernel-side POLL... and unifying {de,}mangle_poll() has to be done after the search-and-replace job, since we need userland-side POLL... for unified {de,}mangle_poll(), thus the cherry-pick at the last step. After that we will have: - POLL{IN,OUT,...} *not* in __poll_t, so any stray instances of ->poll() still using those will be caught by sparse. - eventpoll.c and select.c warning-free wrt __poll_t - no more kernel-side definitions of POLL... - userland ones are visible through the entire kernel (and used pretty much only for mangle/demangle) - same behavior as after the first series (i.e. sparc et.al. epoll(2) working correctly)" * 'work.poll2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: annotate ep_scan_ready_list() ep_send_events_proc(): return result via esed->res preparation to switching ->poll() to returning EPOLL... add EPOLLNVAL, annotate EPOLL... and event_poll->event use linux/poll.h instead of asm/poll.h xen: fix poll misannotation smc: missing poll annotations
| * xen: fix poll misannotationAl Viro2018-02-011-1/+1
| | | | | | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* | Merge tag 'for-linus-20180210' of git://git.kernel.dk/linux-blockLinus Torvalds2018-02-109-36/+111
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull block fixes from Jens Axboe: "A few fixes to round off the merge window on the block side: - a set of bcache fixes by way of Michael Lyle, from the usual bcache suspects. - add a simple-to-hook-into function for bpf EIO error injection. - fix blk-wbt that mischarectized flushes as reads. Improve the logic so that flushes and writes are accounted as writes, and only reads as reads. From me. - fix requeue crash in BFQ, from Paolo" * tag 'for-linus-20180210' of git://git.kernel.dk/linux-block: block, bfq: add requeue-request hook bcache: fix for data collapse after re-attaching an attached device bcache: return attach error when no cache set exist bcache: set writeback_rate_update_seconds in range [1, 60] seconds bcache: fix for allocator and register thread race bcache: set error_limit correctly bcache: properly set task state in bch_writeback_thread() bcache: fix high CPU occupancy during journal bcache: add journal statistic block: Add should_fail_bio() for bpf error injection blk-wbt: account flush requests correctly
| * \ Merge branch 'for-linus' into testJens Axboe2018-02-079-36/+111
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * for-linus: block, bfq: add requeue-request hook bcache: fix for data collapse after re-attaching an attached device bcache: return attach error when no cache set exist bcache: set writeback_rate_update_seconds in range [1, 60] seconds bcache: fix for allocator and register thread race bcache: set error_limit correctly bcache: properly set task state in bch_writeback_thread() bcache: fix high CPU occupancy during journal bcache: add journal statistic block: Add should_fail_bio() for bpf error injection blk-wbt: account flush requests correctly
| | * | bcache: fix for data collapse after re-attaching an attached deviceTang Junhui2018-02-073-7/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | back-end device sdm has already attached a cache_set with ID f67ebe1f-f8bc-4d73-bfe5-9dc88607f119, then try to attach with another cache set, and it returns with an error: [root]# cd /sys/block/sdm/bcache [root]# echo 5ccd0a63-148e-48b8-afa2-aca9cbd6279f > attach -bash: echo: write error: Invalid argument After that, execute a command to modify the label of bcache device: [root]# echo data_disk1 > label Then we reboot the system, when the system power on, the back-end device can not attach to cache_set, a messages show in the log: Feb 5 12:05:52 ceph152 kernel: [922385.508498] bcache: bch_cached_dev_attach() couldn't find uuid for sdm in set In sysfs_attach(), dc->sb.set_uuid was assigned to the value which input through sysfs, no matter whether it is success or not in bch_cached_dev_attach(). For example, If the back-end device has already attached to an cache set, bch_cached_dev_attach() would fail, but dc->sb.set_uuid was changed. Then modify the label of bcache device, it will call bch_write_bdev_super(), which would write the dc->sb.set_uuid to the super block, so we record a wrong cache set ID in the super block, after the system reboot, the cache set couldn't find the uuid of the back-end device, so the bcache device couldn't exist and use any more. In this patch, we don't assigned cache set ID to dc->sb.set_uuid in sysfs_attach() directly, but input it into bch_cached_dev_attach(), and assigned dc->sb.set_uuid to the cache set ID after the back-end device attached to the cache set successful. Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn> Reviewed-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
| | * | bcache: return attach error when no cache set existTang Junhui2018-02-071-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I attach a back-end device to a cache set, and the cache set is not registered yet, this back-end device did not attach successfully, and no error returned: [root]# echo 87859280-fec6-4bcc-20df7ca8f86b > /sys/block/sde/bcache/attach [root]# In sysfs_attach(), the return value "v" is initialized to "size" in the beginning, and if no cache set exist in bch_cache_sets, the "v" value would not change any more, and return to sysfs, sysfs regard it as success since the "size" is a positive number. This patch fixes this issue by assigning "v" with "-ENOENT" in the initialization. Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn> Reviewed-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
| | * | bcache: set writeback_rate_update_seconds in range [1, 60] secondsColy Li2018-02-073-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | dc->writeback_rate_update_seconds can be set via sysfs and its value can be set to [1, ULONG_MAX]. It does not make sense to set such a large value, 60 seconds is long enough value considering the default 5 seconds works well for long time. Because dc->writeback_rate_update is a special delayed work, it re-arms itself inside the delayed work routine update_writeback_rate(). When stopping it by cancel_delayed_work_sync(), there should be a timeout to wait and make sure the re-armed delayed work is stopped too. A small max value of dc->writeback_rate_update_seconds is also helpful to decide a reasonable small timeout. This patch limits sysfs interface to set dc->writeback_rate_update_seconds in range of [1, 60] seconds, and replaces the hand-coded number by macros. Changelog: v2: fix a rebase typo in v4, which is pointed out by Michael Lyle. v1: initial version. Signed-off-by: Coly Li <colyli@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
| | * | bcache: fix for allocator and register thread raceTang Junhui2018-02-072-4/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After long time running of random small IO writing, I reboot the machine, and after the machine power on, I found bcache got stuck, the stack is: [root@ceph153 ~]# cat /proc/2510/task/*/stack [<ffffffffa06b2455>] closure_sync+0x25/0x90 [bcache] [<ffffffffa06b6be8>] bch_journal+0x118/0x2b0 [bcache] [<ffffffffa06b6dc7>] bch_journal_meta+0x47/0x70 [bcache] [<ffffffffa06be8f7>] bch_prio_write+0x237/0x340 [bcache] [<ffffffffa06a8018>] bch_allocator_thread+0x3c8/0x3d0 [bcache] [<ffffffff810a631f>] kthread+0xcf/0xe0 [<ffffffff8164c318>] ret_from_fork+0x58/0x90 [<ffffffffffffffff>] 0xffffffffffffffff [root@ceph153 ~]# cat /proc/2038/task/*/stack [<ffffffffa06b1abd>] __bch_btree_map_nodes+0x12d/0x150 [bcache] [<ffffffffa06b1bd1>] bch_btree_insert+0xf1/0x170 [bcache] [<ffffffffa06b637f>] bch_journal_replay+0x13f/0x230 [bcache] [<ffffffffa06c75fe>] run_cache_set+0x79a/0x7c2 [bcache] [<ffffffffa06c0cf8>] register_bcache+0xd48/0x1310 [bcache] [<ffffffff812f702f>] kobj_attr_store+0xf/0x20 [<ffffffff8125b216>] sysfs_write_file+0xc6/0x140 [<ffffffff811dfbfd>] vfs_write+0xbd/0x1e0 [<ffffffff811e069f>] SyS_write+0x7f/0xe0 [<ffffffff8164c3c9>] system_call_fastpath+0x16/0x1 The stack shows the register thread and allocator thread were getting stuck when registering cache device. I reboot the machine several times, the issue always exsit in this machine. I debug the code, and found the call trace as bellow: register_bcache() ==>run_cache_set() ==>bch_journal_replay() ==>bch_btree_insert() ==>__bch_btree_map_nodes() ==>btree_insert_fn() ==>btree_split() //node need split ==>btree_check_reserve() In btree_check_reserve(), It will check if there is enough buckets of RESERVE_BTREE type, since allocator thread did not work yet, so no buckets of RESERVE_BTREE type allocated, so the register thread waits on c->btree_cache_wait, and goes to sleep. Then the allocator thread initialized, the call trace is bellow: bch_allocator_thread() ==>bch_prio_write() ==>bch_journal_meta() ==>bch_journal() ==>journal_wait_for_write() In journal_wait_for_write(), It will check if journal is full by journal_full(), but the long time random small IO writing causes the exhaustion of journal buckets(journal.blocks_free=0), In order to release the journal buckets, the allocator calls btree_flush_write() to flush keys to btree nodes, and waits on c->journal.wait until btree nodes writing over or there has already some journal buckets space, then the allocator thread goes to sleep. but in btree_flush_write(), since bch_journal_replay() is not finished, so no btree nodes have journal (condition "if (btree_current_write(b)->journal)" never satisfied), so we got no btree node to flush, no journal bucket released, and allocator sleep all the times. Through the above analysis, we can see that: 1) Register thread wait for allocator thread to allocate buckets of RESERVE_BTREE type; 2) Alloctor thread wait for register thread to replay journal, so it can flush btree nodes and get journal bucket. then they are all got stuck by waiting for each other. Hua Rui provided a patch for me, by allocating some buckets of RESERVE_BTREE type in advance, so the register thread can get bucket when btree node splitting and no need to waiting for the allocator thread. I tested it, it has effect, and register thread run a step forward, but finally are still got stuck, the reason is only 8 bucket of RESERVE_BTREE type were allocated, and in bch_journal_replay(), after 2 btree nodes splitting, only 4 bucket of RESERVE_BTREE type left, then btree_check_reserve() is not satisfied anymore, so it goes to sleep again, and in the same time, alloctor thread did not flush enough btree nodes to release a journal bucket, so they all got stuck again. So we need to allocate more buckets of RESERVE_BTREE type in advance, but how much is enough? By experience and test, I think it should be as much as journal buckets. Then I modify the code as this patch, and test in the machine, and it works. This patch modified base on Hua Rui’s patch, and allocate more buckets of RESERVE_BTREE type in advance to avoid register thread and allocate thread going to wait for each other. [patch v2] ca->sb.njournal_buckets would be 0 in the first time after cache creation, and no journal exists, so just 8 btree buckets is OK. Signed-off-by: Hua Rui <huarui.dev@gmail.com> Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn> Reviewed-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
| | * | bcache: set error_limit correctlyColy Li2018-02-073-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Struct cache uses io_errors for two purposes, - Error decay: when cache set error_decay is set, io_errors is used to generate a small piece of delay when I/O error happens. - I/O errors counter: in order to generate big enough value for error decay, I/O errors counter value is stored by left shifting 20 bits (a.k.a IO_ERROR_SHIFT). In function bch_count_io_errors(), if I/O errors counter reaches cache set error limit, bch_cache_set_error() will be called to retire the whold cache set. But current code is problematic when checking the error limit, see the following code piece from bch_count_io_errors(), 90 if (error) { 91 char buf[BDEVNAME_SIZE]; 92 unsigned errors = atomic_add_return(1 << IO_ERROR_SHIFT, 93 &ca->io_errors); 94 errors >>= IO_ERROR_SHIFT; 95 96 if (errors < ca->set->error_limit) 97 pr_err("%s: IO error on %s, recovering", 98 bdevname(ca->bdev, buf), m); 99 else 100 bch_cache_set_error(ca->set, 101 "%s: too many IO errors %s", 102 bdevname(ca->bdev, buf), m); 103 } At line 94, errors is right shifting IO_ERROR_SHIFT bits, now it is real errors counter to compare at line 96. But ca->set->error_limit is initia- lized with an amplified value in bch_cache_set_alloc(), 1545 c->error_limit = 8 << IO_ERROR_SHIFT; It means by default, in bch_count_io_errors(), before 8<<20 errors happened bch_cache_set_error() won't be called to retire the problematic cache device. If the average request size is 64KB, it means bcache won't handle failed device until 512GB data is requested. This is too large to be an I/O threashold. So I believe the correct error limit should be much less. This patch sets default cache set error limit to 8, then in bch_count_io_errors() when errors counter reaches 8 (if it is default value), function bch_cache_set_error() will be called to retire the whole cache set. This patch also removes bits shifting when store or show io_error_limit value via sysfs interface. Nowadays most of SSDs handle internal flash failure automatically by LBA address re-indirect mapping. If an I/O error can be observed by upper layer code, it will be a notable error because that SSD can not re-indirect map the problematic LBA address to an available flash block. This situation indicates the whole SSD will be failed very soon. Therefore setting 8 as the default io error limit value makes sense, it is enough for most of cache devices. Changelog: v2: add reviewed-by from Hannes. v1: initial version for review. Signed-off-by: Coly Li <colyli@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tang Junhui <tang.junhui@zte.com.cn> Reviewed-by: Michael Lyle <mlyle@lyle.org> Cc: Junhui Tang <tang.junhui@zte.com.cn> Signed-off-by: Jens Axboe <axboe@kernel.dk>
| | * | bcache: properly set task state in bch_writeback_thread()Coly Li2018-02-072-3/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Kernel thread routine bch_writeback_thread() has the following code block, 447 down_write(&dc->writeback_lock); 448~450 if (check conditions) { 451 up_write(&dc->writeback_lock); 452 set_current_state(TASK_INTERRUPTIBLE); 453 454 if (kthread_should_stop()) 455 return 0; 456 457 schedule(); 458 continue; 459 } If condition check is true, its task state is set to TASK_INTERRUPTIBLE and call schedule() to wait for others to wake up it. There are 2 issues in current code, 1, Task state is set to TASK_INTERRUPTIBLE after the condition checks, if another process changes the condition and call wake_up_process(dc-> writeback_thread), then at line 452 task state is set back to TASK_INTERRUPTIBLE, the writeback kernel thread will lose a chance to be waken up. 2, At line 454 if kthread_should_stop() is true, writeback kernel thread will return to kernel/kthread.c:kthread() with TASK_INTERRUPTIBLE and call do_exit(). It is not good to enter do_exit() with task state TASK_INTERRUPTIBLE, in following code path might_sleep() is called and a warning message is reported by __might_sleep(): "WARNING: do not call blocking ops when !TASK_RUNNING; state=1 set at [xxxx]". For the first issue, task state should be set before condition checks. Ineed because dc->writeback_lock is required when modifying all the conditions, calling set_current_state() inside code block where dc-> writeback_lock is hold is safe. But this is quite implicit, so I still move set_current_state() before all the condition checks. For the second issue, frankley speaking it does not hurt when kernel thread exits with TASK_INTERRUPTIBLE state, but this warning message scares users, makes them feel there might be something risky with bcache and hurt their data. Setting task state to TASK_RUNNING before returning fixes this problem. In alloc.c:allocator_wait(), there is also a similar issue, and is also fixed in this patch. Changelog: v3: merge two similar fixes into one patch v2: fix the race issue in v1 patch. v1: initial buggy fix. Signed-off-by: Coly Li <colyli@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Michael Lyle <mlyle@lyle.org> Cc: Michael Lyle <mlyle@lyle.org> Cc: Junhui Tang <tang.junhui@zte.com.cn> Signed-off-by: Jens Axboe <axboe@kernel.dk>
| | * | bcache: fix high CPU occupancy during journalTang Junhui2018-02-073-15/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After long time small writing I/O running, we found the occupancy of CPU is very high and I/O performance has been reduced by about half: [root@ceph151 internal]# top top - 15:51:05 up 1 day,2:43, 4 users, load average: 16.89, 15.15, 16.53 Tasks: 2063 total, 4 running, 2059 sleeping, 0 stopped, 0 zombie %Cpu(s):4.3 us, 17.1 sy 0.0 ni, 66.1 id, 12.0 wa, 0.0 hi, 0.5 si, 0.0 st KiB Mem : 65450044 total, 24586420 free, 38909008 used, 1954616 buff/cache KiB Swap: 65667068 total, 65667068 free, 0 used. 25136812 avail Mem PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2023 root 20 0 0 0 0 S 55.1 0.0 0:04.42 kworker/11:191 14126 root 20 0 0 0 0 S 42.9 0.0 0:08.72 kworker/10:3 9292 root 20 0 0 0 0 S 30.4 0.0 1:10.99 kworker/6:1 8553 ceph 20 0 4242492 1.805g 18804 S 30.0 2.9 410:07.04 ceph-osd 12287 root 20 0 0 0 0 S 26.7 0.0 0:28.13 kworker/7:85 31019 root 20 0 0 0 0 S 26.1 0.0 1:30.79 kworker/22:1 1787 root 20 0 0 0 0 R 25.7 0.0 5:18.45 kworker/8:7 32169 root 20 0 0 0 0 S 14.5 0.0 1:01.92 kworker/23:1 21476 root 20 0 0 0 0 S 13.9 0.0 0:05.09 kworker/1:54 2204 root 20 0 0 0 0 S 12.5 0.0 1:25.17 kworker/9:10 16994 root 20 0 0 0 0 S 12.2 0.0 0:06.27 kworker/5:106 15714 root 20 0 0 0 0 R 10.9 0.0 0:01.85 kworker/19:2 9661 ceph 20 0 4246876 1.731g 18800 S 10.6 2.8 403:00.80 ceph-osd 11460 ceph 20 0 4164692 2.206g 18876 S 10.6 3.5 360:27.19 ceph-osd 9960 root 20 0 0 0 0 S 10.2 0.0 0:02.75 kworker/2:139 11699 ceph 20 0 4169244 1.920g 18920 S 10.2 3.1 355:23.67 ceph-osd 6843 ceph 20 0 4197632 1.810g 18900 S 9.6 2.9 380:08.30 ceph-osd The kernel work consumed a lot of CPU, and I found they are running journal work, The journal is reclaiming source and flush btree node with surprising frequency. Through further analysis, we found that in btree_flush_write(), we try to get a btree node with the smallest fifo idex to flush by traverse all the btree nodein c->bucket_hash, after we getting it, since no locker protects it, this btree node may have been written to cache device by other works, and if this occurred, we retry to traverse in c->bucket_hash and get another btree node. When the problem occurrd, the retry times is very high, and we consume a lot of CPU in looking for a appropriate btree node. In this patch, we try to record 128 btree nodes with the smallest fifo idex in heap, and pop one by one when we need to flush btree node. It greatly reduces the time for the loop to find the appropriate BTREE node, and also reduce the occupancy of CPU. [note by mpl: this triggers a checkpatch error because of adjacent, pre-existing style violations] Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn> Reviewed-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
| | * | bcache: add journal statisticTang Junhui2018-02-073-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sometimes, Journal takes up a lot of CPU, we need statistics to know what's the journal is doing. So this patch provide some journal statistics: 1) reclaim: how many times the journal try to reclaim resource, usually the journal bucket or/and the pin are exhausted. 2) flush_write: how many times the journal try to flush btree node to cache device, usually the journal bucket are exhausted. 3) retry_flush_write: how many times the journal retry to flush the next btree node, usually the previous tree node have been flushed by other thread. we show these statistic by sysfs interface. Through these statistics We can totally see the status of journal module when the CPU is too high. Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn> Reviewed-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
* | | | Merge tag 'platform-drivers-x86-v4.16-3' of git://github.com/dvhart/linux-pdx86Linus Torvalds2018-02-102-11/+363
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull x86 platform driver updates from Darren Hart: "Mellanox fixes and new system type support. Mostly data for new system types with a correction and an uninitialized variable fix" [ Pulling from github because git.infradead.org currently seems to be down for some reason, but Darren had a backup location - Linus ] * tag 'platform-drivers-x86-v4.16-3' of git://github.com/dvhart/linux-pdx86: platform/x86: mlx-platform: Add support for new 200G IB and Ethernet systems platform/x86: mlx-platform: Add support for new msn201x system type platform/x86: mlx-platform: Add support for new msn274x system type platform/x86: mlx-platform: Fix power cable setting for msn21xx family platform/x86: mlx-platform: Add define for the negative bus platform/x86: mlx-platform: Use defines for bus assignment platform/mellanox: mlxreg-hotplug: Fix uninitialized variable
| * | | | platform/x86: mlx-platform: Add support for new 200G IB and Ethernet systemsVadim Pasternak2018-02-091-0/+142
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It adds support for new Mellanox system types of basic classes qmb7, sn34, sn37, containing systems QMB700 (40x200GbE InfiniBand switch), SN3700 (32x200GbE and 16x400GbE Ethernet switch) and SN3410 (6x400GbE plus 48x50GbE Ethernet switch). These are the Top of the Rack systems, equipped with Mellanox COM-Express carrier board and switch board with Mellanox Quantum device, which supports InfiniBand switching with 40X200G ports and line rate of up to HDR speed or with Mellanox Spectrum-2 device, which supports Ethernet switching with 32X200G ports line rate of up to HDR speed. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
| * | | | platform/x86: mlx-platform: Add support for new msn201x system typeVadim Pasternak2018-02-091-0/+59
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It adds support for new Mellanox system types of basic half unit size class msn201x, containing system MSN2010 (18x10GbE plus 4x4x25GbE) half and its derivatives. This is the Top of the Rack system, equipped with Mellanox Small Form Factor carrier board and switch board with Mellanox Spectrum device, which supports Ethernet switching with 32X100G ports line rate of up to EDR speed. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
| * | | | platform/x86: mlx-platform: Add support for new msn274x system typeVadim Pasternak2018-02-091-0/+124
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It adds support for new Mellanox system types of basic class msn274x, containing system MSN2740 (32x100GbE Ethernet switch with cost reduction) and its derivatives. These are the Top of the Rack system, equipped with Mellanox Small Form Factor carrier board and switch board with Mellanox Spectrum device, which supports Ethernet switching with 32X100G ports line rate of up to EDR speed. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
| * | | | platform/x86: mlx-platform: Fix power cable setting for msn21xx familyVadim Pasternak2018-02-081-2/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add dedicated structure with power cable setting for Mellanox msn21xx family. These systems do not have a physical device for the power unit controller. When the power cable is inserted or removed, the relevant interrupt signal is handled, the status is updated, but no device is associated with the signal. Add definition for interrupt low aggregation signal. On system from msn21xx family, low aggregation mask should be removed in order to allow signal to hit CPU. Fixes: 6613d18e9038 ("platform/x86: mlx-platform: Move module from arch/x86") Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
| * | | | platform/x86: mlx-platform: Add define for the negative busVadim Pasternak2018-02-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add define for the negative bus ID in order to use it in case no hotplug device is associated with the hotplug interrupt signal. In this case, the signal will be handled by the mlxreg-hotplug driver, but no device will be associated with the signal. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
| * | | | platform/x86: mlx-platform: Use defines for bus assignmentVadim Pasternak2018-02-081-8/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add defines for the bus IDs, used for hotplug device topology to improve code readability. Defines added for FAN and power units. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
| * | | | platform/mellanox: mlxreg-hotplug: Fix uninitialized variableGeert Uytterhoeven2018-02-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With gcc-4.1.2: drivers/platform/mellanox/mlxreg-hotplug.c: In function ‘mlxreg_hotplug_health_work_helper’: drivers/platform/mellanox/mlxreg-hotplug.c:347: warning: ‘ret’ is used uninitialized in this function Indeed, if mlxreg_core_item.count is zero, ret is used uninitialized. While this is unlikely to happen (it is set to ARRAY_SIZE(...) in x86 board files), this is done in another source file, so fix this by preinitializing ret to zero. Fixes: c6acad68eb2dbffd ("platform/mellanox: mlxreg-hotplug: Modify to use a regmap interface") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
* | | | | Merge tag 'chrome-platform-for-linus-4.16' of ↵Linus Torvalds2018-02-104-19/+57
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform Pull chrome platform updates from Benson Leung: - move cros_ec_dev to drivers/mfd - other small maintenance fixes [ The cros_ec_dev movement came in earlier through the MFD tree - Linus ] * tag 'chrome-platform-for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform: platform/chrome: Use proper protocol transfer function platform/chrome: cros_ec_lpc: Add support for Google Glimmer platform/chrome: cros_ec_lpc: Register the driver if ACPI entry is missing. platform/chrome: cros_ec_lpc: remove redundant pointer request cros_ec: fix nul-termination for firmware build info platform/chrome: chromeos_laptop: make chromeos_laptop const
| * | | | | platform/chrome: Use proper protocol transfer functionShawn Nematbakhsh2017-12-171-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | pkt_xfer should be used for protocol v3, and cmd_xfer otherwise. We had one instance of these functions correct, but not the second, fall-back case. We use the fall-back only when the first command returns an IN_PROGRESS status, which is only used on some EC firmwares where we don't want to constantly poll the bus, but instead back off and sleep/retry for a little while. Fixes: 2c7589af3c4d ("mfd: cros_ec: add proto v3 skeleton") Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Benson Leung <bleung@chromium.org>
| * | | | | platform/chrome: cros_ec_lpc: Add support for Google GlimmerThierry Escande2017-12-171-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds device information to the DMI table of the cros_ec_lpc driver for Google Glimmer devices. Since Google BIOS does not enumerate devices in the LPC bus, the cros_ec_lpc driver checks for system compatibility and registers the cros_ec device itself. Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Reviewed-by: Gwendal Grignou <gwendal@chromium.org> Signed-off-by: Benson Leung <bleung@chromium.org>
| * | | | | platform/chrome: cros_ec_lpc: Register the driver if ACPI entry is missing.Enric Balletbo i Serra2017-12-171-1/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 12278dc7c572 ("platform/chrome: cros_ec_lpc: Add support for GOOG004 ACPI device") added support when the firmware reports the ACPI device, there are some firmwares though that doesn't report this device but have it. In such cases we need to instantiate the driver explicitly if it is not instantiated through ACPI. Fixes: 12278dc7c572 ("platform/chrome: cros_ec_lpc: Add support for GOOG004 ACPI device") Signed-off-by: Guenter Roeck <groeck@chromium.org> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Reviewed-by: Gwendal Grignou <gwendal@chromium.org> Signed-off-by: Benson Leung <bleung@chromium.org>
| * | | | | platform/chrome: cros_ec_lpc: remove redundant pointer requestColin Ian King2017-12-171-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pointer request is being assigned but never used, so remove it. Cleans up the clang warning: drivers/platform/chrome/cros_ec_lpc.c:68:2: warning: Value stored to 'request' is never read Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Benson Leung <bleung@chromium.org>
| * | | | | cros_ec: fix nul-termination for firmware build infoArnd Bergmann2017-12-151-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As gcc-8 reports, we zero out the wrong byte: drivers/platform/chrome/cros_ec_sysfs.c: In function 'show_ec_version': drivers/platform/chrome/cros_ec_sysfs.c:190:12: error: array subscript 4294967295 is above array bounds of 'uint8_t[]' [-Werror=array-bounds] This changes the code back to what it did before changing to a zero-length array structure. Fixes: a841178445bb ("mfd: cros_ec: Use a zero-length array for command data") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Benson Leung <bleung@chromium.org>
| * | | | | platform/chrome: chromeos_laptop: make chromeos_laptop constBhumika Goyal2017-12-151-11/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Declare chromeos_laptop structures as const as they are only used during a copy operation. As their value is never modified during runtime, they can be made const. Signed-off-by: Bhumika Goyal <bhumirks@gmail.com> Signed-off-by: Benson Leung <bleung@chromium.org>
| * | | | | Merge branch 'ibs-for-chrome-platform-merged' into working-branch-for-4.16Benson Leung2017-12-1512-51/+33
| |\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Benson Leung <bleung@chromium.org>
* | \ \ \ \ \ Merge tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds2018-02-108-2/+1017
|\ \ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull KVM updates from Radim Krčmář: "ARM: - icache invalidation optimizations, improving VM startup time - support for forwarded level-triggered interrupts, improving performance for timers and passthrough platform devices - a small fix for power-management notifiers, and some cosmetic changes PPC: - add MMIO emulation for vector loads and stores - allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without requiring the complex thread synchronization of older CPU versions - improve the handling of escalation interrupts with the XIVE interrupt controller - support decrement register migration - various cleanups and bugfixes. s390: - Cornelia Huck passed maintainership to Janosch Frank - exitless interrupts for emulated devices - cleanup of cpuflag handling - kvm_stat counter improvements - VSIE improvements - mm cleanup x86: - hypervisor part of SEV - UMIP, RDPID, and MSR_SMI_COUNT emulation - paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit - allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more AVX512 features - show vcpu id in its anonymous inode name - many fixes and cleanups - per-VCPU MSR bitmaps (already merged through x86/pti branch) - stable KVM clock when nesting on Hyper-V (merged through x86/hyperv)" * tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (197 commits) KVM: PPC: Book3S: Add MMIO emulation for VMX instructions KVM: PPC: Book3S HV: Branch inside feature section KVM: PPC: Book3S HV: Make HPT resizing work on POWER9 KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code KVM: PPC: Book3S PR: Fix broken select due to misspelling KVM: x86: don't forget vcpu_put() in kvm_arch_vcpu_ioctl_set_sregs() KVM: PPC: Book3S PR: Fix svcpu copying with preemption enabled KVM: PPC: Book3S HV: Drop locks before reading guest memory kvm: x86: remove efer_reload entry in kvm_vcpu_stat KVM: x86: AMD Processor Topology Information x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested kvm: embed vcpu id to dentry of vcpu anon inode kvm: Map PFN-type memory regions as writable (if possible) x86/kvm: Make it compile on 32bit and with HYPYERVISOR_GUEST=n KVM: arm/arm64: Fixup userspace irqchip static key optimization KVM: arm/arm64: Fix userspace_irqchip_in_use counting KVM: arm/arm64: Fix incorrect timer_is_pending logic MAINTAINERS: update KVM/s390 maintainers MAINTAINERS: add Halil as additional vfio-ccw maintainer MAINTAINERS: add David as a reviewer for KVM/s390 ...
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-13 03:00:50 +0000