summaryrefslogtreecommitdiffstats
path: root/include/linux/phy.h
Commit message (Collapse)AuthorAgeFilesLines
* net: phy: Introduce PSGMII PHY interface modeGabor Juhos2023-08-141-0/+4
| | | | | | | | | | | | | | | | | | | The PSGMII interface is similar to QSGMII. The main difference is that the PSGMII interface combines five SGMII lines into a single link while in QSGMII only four lines are combined. Similarly to the QSGMII, this interface mode might also needs special handling within the MAC driver. It is commonly used by Qualcomm with their QCA807x PHY series and modern WiSoC-s. Add definitions for the PHY layer to allow to express this type of connection between the MAC and PHY. Signed-off-by: Gabor Juhos <j4g8y7@gmail.com> Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: phy_device: Call into the PHY driver to set LED offloadAndrew Lunn2023-08-101-0/+33
| | | | | | | | | | | | | | | Linux LEDs can be requested to perform hardware accelerated blinking to indicate link, RX, TX etc. Pass the rules for blinking to the PHY driver, if it implements the ops needed to determine if a given pattern can be offloaded, to offload it, and what the current offload is. Additionally implement the op needed to get what device the LED is for. Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/20230808210436.838995-3-andrew@lunn.ch Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: Remove two unused function declarationsYue Haibing2023-08-091-4/+0
| | | | | | | | | | Commit 1e2dc14509fd ("net: ethtool: Add helpers for reporting test results") declared but never implemented these function. Signed-off-by: Yue Haibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230808144610.19096-1-yuehaibing@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: provide phylib stubs for hardware timestamping operationsVladimir Oltean2023-08-021-0/+7
| | | | | | | | | | | | | | | | | | | | net/core/dev_ioctl.c (built-in code) will want to call phy_mii_ioctl() for hardware timestamping purposes. This is not directly possible, because phy_mii_ioctl() is a symbol provided under CONFIG_PHYLIB. Do something similar to what was done in DSA in commit 5a17818682cf ("net: dsa: replace NETDEV_PRE_CHANGE_HWTSTAMP notifier with a stub"), and arrange some indirect calls to phy_mii_ioctl() through a stub structure containing function pointers, that's provided by phylib as built-in even when CONFIG_PHYLIB=m, and which phy_init() populates at runtime (module insertion). Note: maybe the ownership of the ethtool_phy_ops singleton is backwards, and the methods exposed by that should be later merged into phylib_stubs. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20230801142824.1772134-12-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: c45: add a separate function to read BASE-T1 abilitiesStefan Eichenberger2023-07-201-0/+1
| | | | | | | | | | Add a separate function to read the BASE-T1 abilities. Some PHYs do not indicate the availability of the extended BASE-T1 ability register, so this function must be called separately. Signed-off-by: Stefan Eichenberger <eichest@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
* net: phylib: fix phy_read*_poll_timeout()Russell King (Oracle)2023-06-021-6/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Dan Carpenter reported a signedness bug in genphy_loopback(). Andrew reports that: "It is common to get this wrong in general with PHY drivers. Dan regularly posts fixes like this soon after a PHY driver patch it merged. I really wish we could somehow get the compiler to warn when the result from phy_read() is stored into a unsigned type. It would save Dan a lot of work." Let's make phy_read*_poll_timeout() immune to further issues when "val" is an unsigned type by storing the read function's result in a signed int as well as "val", and using the signed variable both to check for an error and for propagating that error to the caller. The advantage of this method is we don't change where the cast from the signed return code to the user's variable occurs - so users will see no change. Previously Heiner changed phy_read_poll_timeout() to check for an error before evaluating the user supplied condition, but didn't update phy_read_mmd_poll_timeout(). Make that change there too. Link: https://lore.kernel.org/r/d7bb312e-2428-45f6-b9b3-59ba544e8b94@kili.mountain Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/E1q4kX6-00BNuM-Mx@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: avoid kernel warning dump when stopping an errored PHYRussell King (Oracle)2023-05-241-2/+5
| | | | | | | | | | | | | | | | | | When taking a network interface down (or removing a SFP module) after the PHY has encountered an error, phy_stop() complains incorrectly that it was called from HALTED state. The reason this is incorrect is that the network driver will have called phy_start() when the interface was brought up, and the fact that the PHY has a problem bears no relationship to the administrative state of the interface. Taking the interface administratively down (which calls phy_stop()) is always the right thing to do after a successful phy_start() call, whether or not the PHY has encountered an error. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: add helpers for comparing phy IDsRussell King2023-05-221-0/+28
| | | | | | | | | | | | | | | | There are several places which open code comparing PHY IDs. Provide a couple of helpers to assist with this, using a slightly simpler test than the original: - phy_id_compare() compares two arbitary PHY IDs and a mask of the significant bits in the ID. - phydev_id_compare() compares the bound phydev with the specified PHY ID, using the bound driver's mask. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2023-05-181-2/+0
|\ | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/ethernet/freescale/fec_main.c 6ead9c98cafc ("net: fec: remove the xdp_return_frame when lack of tx BDs") 144470c88c5d ("net: fec: using the standard return codes when xdp xmit errors") Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * mdio_bus: unhide mdio_bus_init prototypeArnd Bergmann2023-05-171-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | mdio_bus_init() is either used as a local module_init() entry, or it gets called in phy_device.c. In the former case, there is no declaration, which causes a warning: drivers/net/phy/mdio_bus.c:1371:12: error: no previous prototype for 'mdio_bus_init' [-Werror=missing-prototypes] Remove the #ifdef around the declaration to avoid the warning.. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20230516194625.549249-4-arnd@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: phy: Allow drivers to always call into ->suspend()Florian Fainelli2023-05-131-0/+4
|/ | | | | | | | | | | | | | | | | | | | | | | A few PHY drivers are currently attempting to not suspend the PHY when Wake-on-LAN is enabled, however that code is not currently executing at all due to an early check in phy_suspend(). This prevents PHY drivers from making an appropriate decisions and put the hardware into a low power state if desired. In order to allow the PHY drivers to opt into getting their ->suspend routine to be called, add a PHY_ALWAYS_CALL_SUSPEND bit which can be set. A boolean that tracks whether the PHY or the attached MAC has Wake-on-LAN enabled is also provided for convenience. If phydev::wol_enabled then the PHY shall not prevent its own Wake-on-LAN detection logic from working and shall not prevent the Ethernet MAC from receiving packets for matching. Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: phy_device: Call into the PHY driver to set LED blinkingAndrew Lunn2023-04-191-0/+12
| | | | | | | | | | Linux LEDs can be requested to perform hardware accelerated blinking. Pass this to the PHY driver, if it implements the op. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: phy_device: Call into the PHY driver to set LED brightnessAndrew Lunn2023-04-191-0/+13
| | | | | | | | | | | | Linux LEDs can be software controlled via the brightness file in /sys. LED drivers need to implement a brightness_set function which the core will call. Implement an intermediary in phy_device, which will call into the phy driver if it implements the necessary function. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Add a binding for PHY LEDsAndrew Lunn2023-04-191-0/+16
| | | | | | | | | | | | | | | | | Define common binding parsing for all PHY drivers with LEDs using phylib. Parse the DT as part of the phy_probe and add LEDs to the linux LED class infrastructure. For the moment, provide a dummy brightness function, which will later be replaced with a call into the PHY driver. This allows testing since the LED core might otherwise reject an LED whose brightness cannot be set. Add a dependency on LED_CLASS. It either needs to be built in, or not enabled, since a modular build can result in linker errors. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2023-03-301-1/+1
|\ | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/ethernet/mediatek/mtk_ppe.c 3fbe4d8c0e53 ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting") 924531326e2d ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow") Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: phy: constify fwnode_get_phy_node() fwnode argumentRussell King (Oracle)2023-03-271-1/+1
| | | | | | | | | | | | | | | | | | fwnode_get_phy_node() does not motify the fwnode structure, so make the argument const, Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: phy: improve phy_read_poll_timeoutHeiner Kallweit2023-03-071-3/+2
|/ | | | | | | | | | | | | cond sometimes is (val & MASK) what may result in a false positive if val is a negative errno. We shouldn't evaluate cond if val < 0. This has no functional impact here, but it's not nice. Therefore switch order of the checks. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/6d8274ac-4344-23b4-d9a3-cad4c39517d4@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: do not force EEE supportOleksij Rempel2023-02-231-0/+5
| | | | | | | | | | | | | | | | | | | | | | | With following patches: commit 9b01c885be36 ("net: phy: c22: migrate to genphy_c45_write_eee_adv()") commit 5827b168125d ("net: phy: c45: migrate to genphy_c45_write_eee_adv()") we set the advertisement to potentially supported values. This behavior may introduce new regressions on systems where EEE was disabled by default (BIOS or boot loader configuration or by other ways.) At same time, with this patches, we would overwrite EEE advertisement configuration made over ethtool. To avoid this issues, we need to cache initial and ethtool advertisement configuration and store it for later use. Fixes: 9b01c885be36 ("net: phy: c22: migrate to genphy_c45_write_eee_adv()") Fixes: 5827b168125d ("net: phy: c45: migrate to genphy_c45_write_eee_adv()") Fixes: 022c3f87f88e ("net: phy: add genphy_c45_ethtool_get/set_eee() support") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
* net: phy: c45: add genphy_c45_an_config_eee_aneg() functionOleksij Rempel2023-02-231-0/+1
| | | | | | | | | Add new genphy_c45_an_config_eee_aneg() function and replace some of genphy_c45_write_eee_adv() calls. This will be needed by the next patch. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
* net: phy: add genphy_c45_ethtool_get/set_eee() supportOleksij Rempel2023-02-131-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | Add replacement for phy_ethtool_get/set_eee() functions. Current phy_ethtool_get/set_eee() implementation is great and it is possible to make it even better: - this functionality is for devices implementing parts of IEEE 802.3 specification beyond Clause 22. The better place for this code is phy-c45.c - currently it is able to do read/write operations on PHYs with different abilities to not existing registers. It is better to use stored supported_eee abilities to avoid false read/write operations. - the eee_active detection will provide wrong results on not supported link modes. It is better to validate speed/duplex properties against supported EEE link modes. - it is able to support only limited amount of link modes. We have more EEE link modes... By refactoring this code I address most of this point except of the last one. Adding additional EEE link modes will need more work. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: export phy_check_valid() functionOleksij Rempel2023-02-131-0/+1
| | | | | | | | | This function will be needed for genphy_c45_ethtool_get_eee() provided by next patch. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: add genphy_c45_read_eee_abilities() functionOleksij Rempel2023-02-131-0/+6
| | | | | | | | | | | | | | | | | | | Add generic function for EEE abilities defined by IEEE 802.3 specification. For now following registers are supported: - IEEE 802.3-2018 45.2.3.10 EEE control and capability 1 (Register 3.20) - IEEE 802.3cg-2019 45.2.1.186b 10BASE-T1L PMA status register (Register 1.2295) Since I was not able to find any flag signaling support of these registers, we should detect link mode abilities first and then based on these abilities doing EEE link modes detection. Results of EEE ability detection will be stored into new variable phydev->supported_eee. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Remove probe_capabilitiesAndrew Lunn2023-01-191-8/+0
| | | | | | | | | | | | Deciding if to probe of PHYs using C45 is now determine by if the bus provides the C45 read method. This makes probe_capabilities redundant so remove it. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
* net: mdio: Rework scanning of bus ready for quirksAndrew Lunn2023-01-191-1/+1
| | | | | | | | | | | | | | | Some C22 PHYs do bad things when there are C45 transactions on the bus. In order to handle this, the bus needs to be scanned first for C22 at all addresses, and then C45 scanned for all addresses. The Marvell pxa168 driver scans a specific address on the bus to find its PHY. This is a C22 only device, so update it to use the c22 helper. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
* drivers/net/phy: add helpers to get/set PLCA configurationPiergiorgio Beruto2023-01-111-0/+6
| | | | | | | | | | | This patch adds support in phylib to read/write PLCA configuration for Ethernet PHYs that support the OPEN Alliance "10BASE-T1S PLCA Management Registers" specifications. These can be found at https://www.opensig.org/about/specifications/ Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/phy: add connection between ethtool and phylib for PLCAPiergiorgio Beruto2023-01-111-0/+7
| | | | | | | | | This patch adds the required connection between netlink ethtool and phylib to resolve PLCA get/set config and get status messages. Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/phy: add the link modes for the 10BASE-T1S Ethernet PHYPiergiorgio Beruto2023-01-111-0/+14
| | | | | | | | | | | This patch adds the link modes for the IEEE 802.3cg Clause 147 10BASE-T1S Ethernet PHY. According to the specifications, the 10BASE-T1S supports Point-To-Point Full-Duplex, Point-To-Point Half-Duplex and/or Point-To-Multipoint (AKA Multi-Drop) Half-Duplex operations. Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/ethtool: add netlink interface for the PLCA RSPiergiorgio Beruto2023-01-111-0/+57
| | | | | | | | | | | Add support for configuring the PLCA Reconciliation Sublayer on multi-drop PHYs that support IEEE802.3cg-2019 Clause 148 (e.g., 10BASE-T1S). This patch adds the appropriate netlink interface to ethtool. Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: mdio: Add dedicated C45 API to MDIO bus driversAndrew Lunn2023-01-101-0/+5
| | | | | | | | | | | | | | | | | | | Currently C22 and C45 transactions are mixed over a combined API calls which make use of a special bit in the reg address to indicate if a C45 transaction should be performed. This makes it impossible to know if the bus driver actually supports C45. Additionally, many C22 only drivers don't return -EOPNOTSUPP when asked to perform a C45 transaction, they mistaking perform a C22 transaction. This is the first step to cleanly separate C22 from C45. To maintain backwards compatibility until all drivers which are capable of performing C45 are converted to this new API, the helper functions will fall back to the older API if the new API is not supported. Eventually this fallback will be removed. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: allow a phy to opt-out of interrupt handlingMichael Walle2023-01-101-0/+3
| | | | | | | | | | | | | | | | | Until now, it is not possible for a PHY driver to disable interrupts during runtime. If a driver offers the .config_intr() as well as the .handle_interrupt() ops, it is eligible for interrupt handling. Introduce a new flag for the dev_flags property of struct phy_device, which can be set by PHY driver to skip interrupt setup and fall back to polling mode. At the moment, this is used for the MaxLinear PHY which has broken interrupt handling and there is a need to disable interrupts in some cases. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
* net: phy: Update documentation for get_rate_matchingSean Anderson2023-01-011-4/+1
| | | | | | | | | | Now that phylink no longer calls phy_get_rate_matching with PHY_INTERFACE_MODE_NA, phys no longer need to support it. Remove the documentation mandating support. Fixes: 7642cc28fd37 ("net: phylink: fix PHY validation with rate adaption") Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Add link between phy dev and mac devXiaolei Wang2022-11-301-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the external phy used by current mac interface is managed by another mac interface, it means that this network port cannot work independently, especially when the system suspends and resumes, the following trace may appear, so we should create a device link between phy dev and mac dev. WARNING: CPU: 0 PID: 24 at drivers/net/phy/phy.c:983 phy_error+0x20/0x68 Modules linked in: CPU: 0 PID: 24 Comm: kworker/0:2 Not tainted 6.1.0-rc3-00011-g5aaef24b5c6d-dirty #34 Hardware name: Freescale i.MX6 SoloX (Device Tree) Workqueue: events_power_efficient phy_state_machine unwind_backtrace from show_stack+0x10/0x14 show_stack from dump_stack_lvl+0x68/0x90 dump_stack_lvl from __warn+0xb4/0x24c __warn from warn_slowpath_fmt+0x5c/0xd8 warn_slowpath_fmt from phy_error+0x20/0x68 phy_error from phy_state_machine+0x22c/0x23c phy_state_machine from process_one_work+0x288/0x744 process_one_work from worker_thread+0x3c/0x500 worker_thread from kthread+0xf0/0x114 kthread from ret_from_fork+0x14/0x28 Exception stack(0xf0951fb0 to 0xf0951ff8) Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20221130021216.1052230-1-xiaolei.wang@windriver.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* ethtool: linkstate: add a statistic for PHY down eventsJakub Kicinski2022-11-081-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | The previous attempt to augment carrier_down (see Link) was not met with much enthusiasm so let's do the simple thing of exposing what some devices already maintain. Add a common ethtool statistic for link going down. Currently users have to maintain per-driver mapping to extract the right stat from the vendor-specific ethtool -S stats. carrier_down does not fit the bill because it counts a lot of software related false positives. Add the statistic to the extended link state API to steer vendors towards implementing all of it. Implement for bnxt and all Linux-controlled PHYs. mlx5 and (possibly) enic also have a counter for this but I leave the implementation to their maintainers. Link: https://lore.kernel.org/r/20220520004500.2250674-1-kuba@kernel.org Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Link: https://lore.kernel.org/r/20221104190125.684910-1-kuba@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
* net: mdiobus: search for PSE nodes by parsing PHY nodes.Oleksij Rempel2022-10-031-0/+2
| | | | | | | | | Some PHYs can be linked with PSE (Power Sourcing Equipment), so search for related nodes and attach it to the phydev. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phylink: pass supported host PHY interface modes to phylib for SFP's PHYsMarek Behún2022-10-031-0/+4
| | | | | | | | | | | | | | | | | | Pass the supported PHY interface types to phylib if the PHY we are connecting is inside a SFP, so that the PHY driver can select an appropriate host configuration mode for their interface according to the host capabilities. For example the Marvell 88X3310 PHY inside RollBall SFP modules defaults to 10gbase-r mode on host's side, and the marvell10g driver currently does not change this setting. But a host may not support 10gbase-r. For example Turris Omnia only supports sgmii, 1000base-x and 2500base-x modes. The PHY can be configured to use those modes, but in order for the PHY driver to do that, it needs to know which modes are supported. Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Add support for rate matchingSean Anderson2022-09-231-1/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for rate matching (also known as rate adaptation) to the phy subsystem. The general idea is that the phy interface runs at one speed, and the MAC throttles the rate at which it sends packets to the link speed. There's a good overview of several techniques for achieving this at [1]. This patch adds support for three: pause-frame based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and 2BASE-TL), and open-loop-based (such as in 10GBASE-W). This patch makes a few assumptions and a few non assumptions about the types of rate matching available. First, it assumes that different phys may use different forms of rate matching. Second, it assumes that phys can use rate matching for any of their supported link speeds (e.g. if a phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T). Third, it does not assume that all interface modes will use the same form of rate matching. Fourth, it does not assume that all phy devices will support rate matching (even if some do). Relaxing or strengthening these (non-)assumptions could result in a different API. For example, if all interface modes were assumed to use the same form of rate matching, then a bitmask of interface modes supportting rate matching would suffice. For some better visibility into the process, the current rate matching mode is exposed as part of the ethtool ksettings. For the moment, only read access is supported. I'm not sure what userspace might want to configure yet (disable it altogether, disable just one mode, specify the mode to use, etc.). For the moment, since only pause-based rate adaptation support is added in the next few commits, rate matching can be disabled altogether by adjusting the advertisement. 802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and "rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls this feature "rate adaptation". I chose "rate matching" because it is shorter, and because Russell doesn't think "adaptation" is correct in this context. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Add 1000BASE-KX interface modeSean Anderson2022-09-051-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | Add 1000BASE-KX interface mode. This 1G backplane ethernet as described in clause 70. Clause 73 autonegotiation is mandatory, and only full duplex operation is supported. Although at the PMA level this interface mode is identical to 1000BASE-X, it uses a different form of in-band autonegation. This justifies a separate interface mode, since the interface mode (along with the MLO_AN_* autonegotiation mode) sets the type of autonegotiation which will be used on a link. This results in more than just electrical differences between the link modes. With regard to 1000BASE-X, 1000BASE-KX holds a similar position to SGMII: same signaling, but different autonegotiation. PCS drivers (which typically handle in-band autonegotiation) may only support 1000BASE-X, and not 1000BASE-KX. Similarly, the phy mode is used to configure serdes phys with phy_set_mode_ext. Due to the different electrical standards (SFI or XFI vs Clause 70), they will likely want to use different configuration. Adding a phy interface mode for 1000BASE-KX helps simplify configuration in these areas. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Add helper to derive the number of ports from a phy modeMaxime Chevallier2022-08-221-0/+2
| | | | | | | | | | | | | Some phy modes such as QSGMII multiplex several MAC<->PHY links on one single physical interface. QSGMII used to be the only one supported, but other modes such as QUSGMII also carry multiple links. This helper allows getting the number of links that are multiplexed on a given interface. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Introduce QUSGMII PHY modeMaxime Chevallier2022-08-221-0/+4
| | | | | | | | | | | | | | | | | | | | The QUSGMII mode is a derivative of Cisco's USXGMII standard. This standard is pretty similar to SGMII, but allows for faster speeds, and has the build-in bits for Quad and Octa variants (like QSGMII). The main difference with SGMII/QSGMII is that USXGMII/QUSGMII re-uses the preamble to carry various information, named 'Extensions'. As of today, the USXGMII standard only mentions the "PCH" extension, which is used to convey timestamps, allowing in-band signaling of PTP timestamps without having to modify the frame itself. This commit adds support for that mode. When no extension is in use, it behaves exactly like QSGMII, although it's not compatible with QSGMII. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2022-06-301-0/+6
|\ | | | | | | | | | | | | | | drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c 9c5de246c1db ("net: sparx5: mdb add/del handle non-sparx5 devices") fbb89d02e33a ("net: sparx5: Allow mdb entries to both CPU and ports") Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: phy: Don't trigger state machine while in suspendLukas Wunner2022-06-291-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Upon system sleep, mdio_bus_phy_suspend() stops the phy_state_machine(), but subsequent interrupts may retrigger it: They may have been left enabled to facilitate wakeup and are not quiesced until the ->suspend_noirq() phase. Unwanted interrupts may hence occur between mdio_bus_phy_suspend() and dpm_suspend_noirq(), as well as between dpm_resume_noirq() and mdio_bus_phy_resume(). Retriggering the phy_state_machine() through an interrupt is not only undesirable for the reason given in mdio_bus_phy_suspend() (freezing it midway with phydev->lock held), but also because the PHY may be inaccessible after it's suspended: Accesses to USB-attached PHYs are blocked once usb_suspend_both() clears the can_submit flag and PHYs on PCI network cards may become inaccessible upon suspend as well. Amend phy_interrupt() to avoid triggering the state machine if the PHY is suspended. Signal wakeup instead if the attached net_device or its parent has been configured as a wakeup source. (Those conditions are identical to mdio_bus_phy_may_suspend().) Postpone handling of the interrupt until the PHY has resumed. Before stopping the phy_state_machine() in mdio_bus_phy_suspend(), wait for a concurrent phy_interrupt() to run to completion. That is necessary because phy_interrupt() may have checked the PHY's suspend status before the system sleep transition commenced and it may thus retrigger the state machine after it was stopped. Likewise, after re-enabling interrupt handling in mdio_bus_phy_resume(), wait for a concurrent phy_interrupt() to complete to ensure that interrupts which it postponed are properly rerun. The issue was exposed by commit 1ce8b37241ed ("usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling"), but has existed since forever. Fixes: 541cd3ee00a4 ("phylib: Fix deadlock on resume") Link: https://lore.kernel.org/netdev/a5315a8a-32c2-962f-f696-de9a26d30091@samsung.com/ Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: stable@vger.kernel.org # v2.6.33+ Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/b7f386d04e9b5b0e2738f0125743e30676f309ef.1656410895.git.lukas@wunner.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | linux/phy.h: add phydev_err_probe() wrapper for dev_err_probe()Rasmus Villemoes2022-06-161-0/+3
|/ | | | | | | | | | The dev_err_probe() function is quite useful to avoid boilerplate related to -EPROBE_DEFER handling. Add a phydev_err_probe() helper to simplify making use of that from phy drivers which otherwise use the phydev_* helpers. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: export genphy_c45_baset1_read_status()Oleksij Rempel2022-05-091-0/+1
| | | | | | | | Export genphy_c45_baset1_read_status() to make it reusable by PHY drivers. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: introduce genphy_c45_pma_baset1_read_master_slave()Oleksij Rempel2022-05-091-0/+1
| | | | | | | | | Move baset1 specific part of genphy_c45_read_pma() code to separate function to make it reusable by PHY drivers. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: introduce genphy_c45_pma_baset1_setup_master_slave()Oleksij Rempel2022-05-091-0/+1
| | | | | | | | | Move baset1 specific part of genphy_c45_pma_setup_forced() code to separate function to make it reusable by PHY drivers. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Add 10BASE-T1L support in phy-c45Alexandru Tachici2022-05-011-0/+3
| | | | | | | | | | | | | | | | | | This patch is needed because the BASE-T1 uses different registers for status, control and advertisement to those already employed in the existing phy-c45 functions. Where required, genphy_c45 functions will now check whether the device supports BASE-T1 and use the specific registers instead: 45.2.7.19 BASE-T1 AN control register, 45.2.7.20 BASE-T1 AN status, 45.2.7.21 BASE-T1 AN advertisement register, 45.2.7.22 BASE-T1 AN LP Base Page ability register, 45.2.1.185 BASE-T1 PMA/PMD control register. Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethtool: Add 10base-T1L link mode entryAlexandru Tachici2022-05-011-1/+1
| | | | | | | | | Add entry for the 10base-T1L full duplex mode. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2022-03-101-2/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | net/dsa/dsa2.c commit afb3cc1a397d ("net: dsa: unlock the rtnl_mutex when dsa_master_setup() fails") commit e83d56537859 ("net: dsa: replay master state events in dsa_tree_{setup,teardown}_master") https://lore.kernel.org/all/20220307101436.7ae87da0@canb.auug.org.au/ drivers/net/ethernet/intel/ice/ice.h commit 97b0129146b1 ("ice: Fix error with handling of bonding MTU") commit 43113ff73453 ("ice: add TTY for GNSS module for E810T device") https://lore.kernel.org/all/20220310112843.3233bcf1@canb.auug.org.au/ drivers/staging/gdm724x/gdm_lte.c commit fc7f750dc9d1 ("staging: gdm724x: fix use after free in gdm_lte_rx()") commit 4bcc4249b4cf ("staging: Use netif_rx().") https://lore.kernel.org/all/20220308111043.1018a59d@canb.auug.org.au/ Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: phy: correct spelling error of media in documentationColin Foster2022-03-101-2/+2
| | | | | | | | | | | | | | | | | | | | | | The header file incorrectly referenced "median-independant interface" instead of media. Correct this typo. Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Fixes: 4069a572d423 ("net: phy: Document core PHY structures") Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20220309062544.3073-1-colin.foster@in-advantage.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: phy: exported the genphy_read_master_slave functionArun Ramadoss2022-03-081-0/+1
| | | | | | | | | | | | | | | | | | | | genphy_read_master_slave function allows to configure the master/slave for gigabit phys only. In order to use this function irrespective of speed, moved the speed check to the genphy_read_status call. Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-14 18:26:31 +0000