summaryrefslogtreecommitdiffstats
path: root/include/linux/qed
Commit message (Collapse)AuthorAgeFilesLines
* qed*: Fix possible overflow for status block id field.sudarsana.kalluru@cavium.com2017-05-041-1/+1
| | | | | | | | | Value for status block id could be more than 256 in 100G mode, need to update its data type from u8 to u16. Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed*: Fix issues in the ptp filter config implementation.sudarsana.kalluru@cavium.com2017-05-021-6/+17
| | | | | | | | | | | | | | | | | | | | | PTP hardware filter configuration performed by the driver for a given user requested config is not correct for some of the PTP modes. Following changes are needed for PTP config-filter implementation. 1. NIG_REG_TX_PTP_EN register - Bits 0/1/2 respectively enables TimeSync/"V1 frame format support"/"V2 frame format support" on the TX side. Set the associated bits based on the user request. 2. ptp4l application fails to operate in Peer Delay mode. Following changes are needed to fix this, a. Driver should enable (set to 0) DA #1-related bits for IPv4, IPv6 and MAC destination addresses in these registers: NIG_REG_TX_LLH_PTP_RULE_MASK NIG_REG_LLH_PTP_RULE_MASK b. NIG_REG_LLH_PTP_PARAM_MASK/NIG_REG_TX_LLH_PTP_PARAM_MASK should be set to 0x0 in all modes. Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: output the DPM status and WID countRam Amrani2017-05-011-0/+2
| | | | | | | | | Output to the RDMA driver whether DPM mode is enabled or disabled in the HW and if so what is the number of WIDs it supports Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed/qede: Add UDP ports in bulletin boardChopra, Manish2017-04-251-0/+1
| | | | | | | | | This patch adds support for UDP ports in bulletin board to notify UDP ports change to the VFs Signed-off-by: Manish Chopra <manish.chopra@cavium.com> Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed/qede: Enable tunnel offloads based on hw configurationChopra, Manish2017-04-251-0/+5
| | | | | | | | | This patch enables tunnel feature offloads based on hw configuration at initialization time instead of enabling them always. Signed-off-by: Manish Chopra <manish.chopra@cavium.com> Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Add support for static dcbx.sudarsana.kalluru@cavium.com2017-04-241-0/+1
| | | | | | | | | | | The patch adds driver support for static/local dcbx mode. In this mode adapter brings up the dcbx link with locally configured parameters instead of performing the dcbx negotiation with the peer. The feature is useful when peer device/switch doesn't support dcbx. Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: aRFS infrastructure supportChopra, Manish2017-04-172-0/+15
| | | | | | | | | | | | | This patch adds necessary APIs to interface with qede aRFS support in successive patch. It also reserves separate PTT entry for aRFS, [as being in fastpath flow] for hardware access instead of trying to acquire it at run time from the ptt pool. Signed-off-by: Manish Chopra <manish.chopra@cavium.com> Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Inform qedi the number of possible CQsMintz, Yuval2017-04-061-0/+2
| | | | | | | | | Now that management firmware is capable of telling us the number of CQs available for a given PF, qed needs to communicate the number to qedi so it would know have many to use. Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Manage with less memory regions for RoCERam Amrani2017-04-031-1/+0
| | | | | | | | | | | It's possible some configurations would prevent driver from utilizing all the Memory Regions due to a lack of ILT lines. In such a case, calculate how many memory regions would have to be dropped due to limit, and manage without those. Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed*: Add support for QL41xxx adaptersMintz, Yuval2017-03-142-13/+38
| | | | | | | | | | | | | This adds the necessary infrastructure changes for initializing and working with the new series of QL41xxx adapaters. It also adds 2 new PCI device-IDs to qede: - 0x8070 for QL41xxx PFs - 0x8090 for VFs spawning from QL41xxx PFs Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed*: Utilize Firmware 8.15.3.0Mintz, Yuval2017-03-137-273/+229
| | | | | | | | | | | | | | | | | | | | | | | | | This patch advances the qed* drivers into using the newer firmware - This solves several firmware bugs, mostly related [but not limited to] various init/deinit issues in various offloaded protocols. It also introduces a major 4-Cached SGE change in firmware, which can be seen in the storage drivers' changes. In addition, this firmware is required for supporting the new QL41xxx series of adapters; While this patch doesn't add the actual support, the firmware contains the necessary initialization & firmware logic to operate such adapters [actual support would be added later on]. Changes from Previous versions: ------------------------------- - V2 - fix kbuild-test robot warnings Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com> Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com> Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Add support for hardware offloaded FCoE.Arun Easi2017-02-194-3/+908
| | | | | | | | | | This adds the backbone required for the various HW initalizations which are necessary for the FCoE driver (qedf) for QLogic FastLinQ 4xxxx line of adapters - FW notification, resource initializations, etc. Signed-off-by: Arun Easi <arun.easi@cavium.com> Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Add infrastructure for PTP supportSudarsana Reddy Kalluru2017-02-151-0/+22
| | | | | | | | | The patch adds the required qed interfaces for configuring/reading the PTP clock on the adapter. Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed*: Add support for ndo_set_vf_trustMintz, Yuval2017-01-011-0/+2
| | | | | | | | Trusted VFs would be allowed to receive promiscuous and multicast promiscuous data. Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed*: RSS indirection based on queue-handlesMintz, Yuval2017-01-011-1/+1
| | | | | | | | | A step toward having qede agnostic to the queue configurations in firmware/hardware - let the RSS indirections use queue handles instead of actual queue indices. Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed*: Update to dual-licenseMintz, Yuval2017-01-0115-57/+368
| | | | | | | | | | | Since the submission of the qedr driver, there's inconsistency in the licensing of the various qed/qede files - some are GPLv2 and some are dual-license. Since qedr requires dual-license and it's dependent on both, we're updating the licensing of all qed/qede source files. Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Add support for hardware offloaded iSCSI.Yuval Mintz2016-12-022-0/+231
| | | | | | | | | | | | This adds the backbone required for the various HW initalizations which are necessary for the iSCSI driver (qedi) for QLogic FastLinQ 4xxxx line of adapters - FW notification, resource initializations, etc. Signed-off-by: Arun Easi <arun.easi@cavium.com> Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed*: Handle-based L2-queues.Mintz, Yuval2016-11-301-27/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The driver needs to maintain several FW/HW-indices for each one of its queues. Currently, that mapping is done by the QED where it uses an rx/tx array of so-called hw-cids, populating them whenever a new queue is opened and clearing them upon destruction of said queues. This maintenance is far from ideal - there's no real reason why QED needs to maintain such a data-structure. It becomes even worse when considering the fact that the PF's queues and its child VFs' queues are all mapped into the same data-structure. As a by-product, the set of parameters an interface needs to supply for queue APIs is non-trivial, and some of the variables in the API structures have different meaning depending on their exact place in the configuration flow. This patch re-organizes the way L2 queues are configured and maintained. In short: - Required parameters for queue init are now well-defined. - Qed would allocate a queue-cid based on parameters. Upon initialization success, it would return a handle to caller. - Queue-handle would be maintained by entity requesting queue-init, not necessarily qed. - All further queue-APIs [update, destroy] would use the opaque handle as reference for the queue instead of various indices. The possible owners of such handles: - PF queues [qede] - complete handles based on provided configuration. - VF queues [qede] - fw-context-less handles, containing only relative information; Only the PF-side would need the absolute indices for configuration, so they're omitted here. - VF queues [qed, PF-side] - complete handles based on VF initialization. Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Optimize qed_chain datapath usageMintz, Yuval2016-11-301-64/+80
| | | | | | | | | | | | | | | | | The chain structure and functions are widely used by the qed* modules, both for configuration and datapath. E.g., qede's Tx has one such chain and its Rx has two. Currently, the strucutre's fields which are required for datapath related functions [produce/consume] are intertwined with fields which are required only for configuration purposes [init/destroy/etc.]. This patch re-arranges the chain structure so that all the fields which are required for datapath usage could reside in a single cacheline instead of the two which are required today. Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Learn resources from management firmwareTomer Tayar2016-10-311-1/+1
| | | | | | | | | | | | | | | Currently, each interfaces assumes it receives an equal portion of HW/FW resources, but this is wasteful - different partitions [and specifically, parititions exposing different protocol support] might require different resources. Implement a new resource learning scheme where the information is received directly from the management firmware [which has knowledge of all of the functions and can serve as arbiter]. Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed*: Add support for WoLMintz, Yuval2016-10-311-0/+10
| | | | | Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Add nvram selftestMintz, Yuval2016-10-311-0/+9
| | | | | Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed*: Management firmware - notifications and defaultsSudarsana Kalluru2016-10-311-0/+28
| | | | | | | | | | | | | | | | Management firmware is interested in various tidbits about the driver - including the driver state & several configuration related fields [MTU, primtary MAC, etc.]. This adds the necessray logic to update MFW with such configurations, some of which are passed directly via qed while for others APIs are provide so that qede would be able to later configure if needed. This also introduces a new default configuration for MTU which would replace the default inherited by being an ethernet device. Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2016-10-302-1/+2
|\ | | | | | | | | | | | | | | | | Mostly simple overlapping changes. For example, David Ahern's adjacency list revamp in 'net-next' conflicted with an adjacency list traversal bug fix in 'net'. Signed-off-by: David S. Miller <davem@davemloft.net>
| * qed*: Reduce the memory footprint for Rx pathSudarsana Reddy Kalluru2016-10-221-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | With the current default values for Rx path i.e., 8 queues of 8Kb entries each with 4Kb size, interface will consume 256Mb for Rx. The default values causing the driver probe to fail when the system memory is low. Based on the perforamnce results, rx-ring count value of 1Kb gives the comparable performance with Rx coalesce timeout of 12 seconds. Updating the default values. Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * qed*: Fix Kconfig dependencies with INFINIBAND_QEDRYuval Mintz2016-10-141-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The qedr driver would require a tristate Kconfig option [to allow it to compile as a module], and toward that end we've added the INFINIBAND_QEDR option. But as we've made the compilation of the qed/qede infrastructure required for RoCE dependent on the option we'd be facing linking difficulties in case that QED=y or QEDE=y, and INFINIBAND_QEDR=m. To resolve this, we seperate between the INFINIBAND_QEDR option and the infrastructure support in qed/qede by introducing a new QED_RDMA option which would be selected by INFINIBAND_QEDR but would be a boolean instead of a tristate; Following that, the qed/qede is fixed based on this new option so that all config combinations would be supported. Fixes: cee9fbd8e2e9 ("qede: add qedr framework") Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qed*: Allow unicast filteringYuval Mintz2016-10-141-0/+1
| | | | | | | | | | | | | | | | | | | | | | Apparently qede fails to set IFF_UNICAST_FLT, and as a result is not actually performing unicast MAC filtering. While we're at it - relax a hard-coded limitation that limits each interface into using at most 15 unicast MAC addresses before turning promiscuous. Instead utilize the HW resources to their limit. Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qed: Pass MAC hints to VFsYuval Mintz2016-10-141-1/+1
|/ | | | | | | | | | | Some hypervisors can support MAC hints to their VFs. Even though we don't have such a hypervisor API in linux, we add sufficient logic for the VF to be able to receive such hints and set the mac accordingly - as long as the VF has not been set with a MAC already. Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Add RoCE ll2 & GSI supportRam Amrani2016-10-031-0/+79
| | | | | | | | | Add the RoCE-specific LL2 logic [as well as GSI support] over the 'generic' LL2 interface. Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Add support for memory registeration verbsRam Amrani2016-10-031-0/+6
| | | | | | | | | Add slowpath configuration support for user, dma and memory regions registration. Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Add support for QP verbsRam Amrani2016-10-031-0/+144
| | | | | | | | | Add support for the slowpath configurations of Queue Pair verbs which adds, deletes, modifies and queries Queue Pairs. Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: PD,PKEY and CQ verb supportRam Amrani2016-10-031-0/+30
| | | | | | | | | Add support for the configurations of the protection domain and completion queues. Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Add support for RoCE hw initRam Amrani2016-10-034-1/+351
| | | | | | | | | | This adds the backbone required for the various HW initalizations which are necessary for the qedr driver - FW notification, resource initializations, etc. Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qede: Add qedr frameworkRam Amrani2016-10-032-2/+89
| | | | | | | | | | | Adds a skeletal implementation of the qede RoCE driver - The qedr has some dependencies of the state of the underlying base interface. This adds some logic required with mutual registrations and the ability to pass updates on 'intresting' events. Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Add Light L2 supportYuval Mintz2016-10-032-0/+140
| | | | | | | | | | Other protocols beside the networking driver need the ability of passing some L2 traffic, usually [although not limited] for the purpose of some management traffic. Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed*: Add support for the ethtool get_regs operationTomer Tayar2016-09-071-0/+4
| | | | | | Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Add support for debug data collectionTomer Tayar2016-09-071-0/+3
| | | | | | | | This patch adds the support for dumping and formatting the HW/FW debug data. Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: Fix address macrosYuval Mintz2016-08-221-14/+8
| | | | | | | | | | | | Last FW submission reverted various macros into an older form, where they generate compilation warnings on some architectures. Bring back the newer macros instead. Fixes: 05fafbfb3d77 ("qed: utilize FW 8.10.10.0") Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed*: Add support for VFs over legacy PFsYuval Mintz2016-08-221-0/+3
| | | | | | | | | | | | | | | | Modern VFs can't run on old non-compatible as the fastpath HSI is slightly changed - but as the HSI is actually very close [basically, a single bit whose meaning flipped] this can be supported with small modifications. The major differences would be in: - Recognizing that VF is running on top of a legacy PF. - Returning some slowpath configurations that are no longer needed on top of modern PFs, but would be required when working over the legacy ones. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed: utilize FW 8.10.10.0Yuval Mintz2016-08-195-131/+442
| | | | | | | | | | | | | | | | | | | | | This new firmware for the qed* adpaters fixes several issues: - Better blocking of malicious VFs. - After FLR, Tx-switching [internal routing] of packets might be incorrect. - Deletion of unicast MAC filters would sometime have side-effect of corrupting the MAC filters configred for a device. It also contains fixes for future qed* drivers that *hopefully* would be sent for review in the near future. In addition, it would allow driver some new functionality, including: - Allowing PF/VF driver compaitibility with old drivers [running pre-8.10.5.0 firmware]. - Better debug facilities. This would also bump the qed* driver versions to 8.10.9.20. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qed*: Fix pause settingYuval Mintz2016-08-181-3/+5
| | | | | | | | | | | When moving into using ethtool's link_ksetting, qed started supplying its own bitmask of speed/capabilities, but qede is still checking for the SUPPORTED value to determine whether it supports pause. Fixes: 054c67d1c82a ("qed*: Add support for ethtool link_ksettings callbacks") Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2016-08-181-0/+8
|\ | | | | | | | | | | | | | | | | Minor overlapping changes for both merge conflicts. Resolution work done by Stephen Rothwell was used as a reference. Signed-off-by: David S. Miller <davem@davemloft.net>
| * qed: Add dcbx app support for IEEE Selection Field.Sudarsana Reddy Kalluru2016-08-081-0/+8
| | | | | | | | | | | | | | | | | | MFW now supports the Selection field for IEEE mode. Add driver changes to use the newer MFW masks to read/write the port-id value. Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qed*: Add support for ethtool link_ksettings callbacks.Sudarsana Reddy Kalluru2016-08-101-0/+15
|/ | | | | | | | | | | | | This patch adds the driver implementation for ethtool link_ksettings callbacks. qed driver now defines/uses the qed specific masks for representing link capability values. qede driver maps these values to to new link modes defined by the kernel implementation of link_ksettings. Please consider applying this to 'net-next' branch. Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2016-06-301-0/+1
|\ | | | | | | | | | | | | | | Several cases of overlapping changes, except the packet scheduler conflicts which deal with the addition of the free list parameter to qdisc_enqueue(). Signed-off-by: David S. Miller <davem@davemloft.net>
| * qed*: Don't reset statistics on inner reloadYuval Mintz2016-06-191-0/+1
| | | | | | | | | | | | | | | | | | | | Several user APIs can cause driver to perform an inner-reload. Currently, doing this would cause the HW/FW statistics of the adapter to reset, which isn't the expected behavior [statistics should only reset on explicit unloads]. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qed: Add support for coalescing config read/update.Sudarsana Reddy Kalluru2016-06-231-0/+24
| | | | | | | | | | | | | | | | | | | | This patch adds support for configuring the device tx/rx coalescing timeout values in the order of micro seconds. It also adds APIs for upper layer drivers for reading/updating the coalescing values. Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qed: Add dcbnl support.Sudarsana Reddy Kalluru2016-06-081-0/+62
| | | | | | | | | | | | | | | | | | This patch adds the implementation for both cee/ieee dcbnl callbacks by using the qed query/config APIs. Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qed: Add support for query/config dcbx.Sudarsana Reddy Kalluru2016-06-081-0/+90
| | | | | | | | | | | | | | | | | | | | Query API reads the dcbx data from the device shared memory and return it to the caller. The config API configures the user provided dcbx values on the device, and initiates the dcbx negotiation with the peer. Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qed: Fix next-ptr chains for BE / 32-bitYuval Mintz2016-06-031-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | Commit a91eb52abb50 ("qed: Revisit chain implementation") contains an incorrect implementation for BE platforms, as device's regpairs containing addresses are LE and they're not converted correctly when read back. In addition, it raises a compilation warning for 32-bit platforms where dma_addr_t is a 32-bit variable. Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 07:46:40 +0000