| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently move_native_irq disables and renables the irq we are migrating to
ensure we don't take that irq when we are actually doing the migration
operation. Disabling the irq needs to happen but sometimes doing the work is
move_native_irq is too late.
On x86 with ioapics the irq move sequences needs to be:
edge_triggered:
mask irq.
move irq.
unmask irq.
ack irq.
level_triggered:
mask irq.
ack irq.
move irq.
unmask irq.
We can easily perform the edge triggered sequence, with the current defintion
of move_native_irq. However the level triggered case does not map well. For
that I have added move_masked_irq, to allow me to disable the irqs around both
the ack and the move.
Q: Why have we not seen this problem earlier?
A: The only symptom I have been able to reproduce is that if we change
the vector before acknowleding an irq the wrong irq is acknowledged.
Since we currently are not reprogramming the irq vector during
migration no problems show up.
We have to mask the irq before we acknowledge the irq or else we could
hit a window where an irq is asserted just before we acknowledge it.
Edge triggered irqs do not have this problem because acknowledgements
do not propogate in the same way.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The primary aim of this patchset is to remove maintenances problems caused by
the irq infrastructure. The two big issues I address are an artificially
small cap on the number of irqs, and that MSI assumes vector == irq. My
primary focus is on x86_64 but I have touched other architectures where
necessary to keep them from breaking.
- To increase the number of irqs I modify the code to look at the (cpu,
vector) pair instead of just looking at the vector.
With a large number of irqs available systems with a large irq count no
longer need to compress their irq numbers to fit. Removing a lot of brittle
special cases.
For acpi guys the result is that irq == gsi.
- Addressing the fact that MSI assumes irq == vector takes a few more
patches. But suffice it to say when I am done none of the generic irq code
even knows what a vector is.
In quick testing on a large Unisys x86_64 machine we stumbled over at least
one driver that assumed that NR_IRQS could always fit into an 8 bit number.
This driver is clearly buggy today. But this has become a class of bugs that
it is now much easier to hit.
This patch:
This is a minor space optimization. In practice I don't think this has any
affect because of our alignment constraints and the other fields but there is
not point in chewing up an uncessary word and since we already read the flag
field this should improve the cache hit ratio of the irq handler.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch converts all the i386 PIC controllers (except VisWS and Voyager,
which I could not test - but which should still work as old-style IRQ layers)
to the new and simpler irq-chip interrupt handling layer.
[akpm@osdl.org: build fix]
[mingo@elte.hu: enable fasteoi handler for i386 level-triggered IO-APIC irqs]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch converts all the x86_64 PIC controllers layers to the new and
simpler irq-chip interrupt handling layer.
[mingo@elte.hu: The patch also enables the fasteoi handler for x86_64]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
make headers_check fails on linux/nfsd/const.h.
Since linux/sunrpc/msg_prot.h does not seem to export anything interesting
for userspace, this patch moves it in the __KERNEL__ protected section.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Use all the pieces set up so far to implement referral support, allowing
return of NFS4ERR_MOVED and fs_locations attribute.
Signed-off-by: Manoj Naik <manoj@almaden.ibm.com>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
| |
Encode fs_locations attribute.
Signed-off-by: Manoj Naik <manoj@almaden.ibm.com>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Define FS locations structures, some functions to manipulate them, and add
code to parse FS locations in downcall and add to the exports structure.
[bfields@fieldses.org: bunch of fixes and cleanups]
Signed-off-by: Manoj Naik <manoj@almaden.ibm.com>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
| |
Store the export path in the svc_export structure instead of storing only the
dentry. This will prevent the need for additional d_path calls to provide
NFSv4 fs_locations support.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
| |
Both the (recently introduces) nsm_sema and the older f_sema are converted
over.
Cc: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The NFSACL patches introduced support for multiple RPC services listening on
the same transport. However, only the first of these services was registered
with portmapper. This was perfectly fine for nfsacl, as you traditionally do
not want these to show up in a portmapper listing.
The patch below changes the default behavior to always register all services
listening on a given transport, but retains the old behavior for nfsacl
services.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Every NLM call includes the client's NSM state. Currently, the Linux client
always reports 0 - which seems not to cause any problems, but is not what the
protocol says.
This patch exposes the kernel's internal variable to user space via a sysctl,
which can be set at system boot time by statd.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When we send a GRANTED_MSG call, we current copy the NLM cookie provided in
the original LOCK call - because in 1996, some broken clients seemed to rely
on this bug. However, this means the cookies are not unique, so that when the
client's GRANTED_RES message comes back, we cannot simply match it based on
the cookie, but have to use the client's IP address in addition. Which breaks
when you have a multi-homed NFS client.
The X/Open spec explicitly mentions that clients should not expect the same
cookie; so one may hope that any clients that were broken in 1996 have either
been fixed or rendered obsolete.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
| |
The way we incremented the NLM cookie in nlmclnt_next_cookie was not thread
safe. This patch changes the counter to an atomic_t
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds the nsm_use_hostnames sysctl and module param. If set, lockd
will use the client's name (as given in the NLM arguments) to find the NSM
handle. This makes recovery work when the NFS peer is multi-homed, and the
reboot notification arrives from a different IP than the original lock calls.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
As a result of previous patches, the loop in nlmsvc_invalidate_all just sets
h_expires for all client/hosts to 0 (though does it in a very complicated
way).
This was possibly meant to trigger early garbage collection but half the time
'0' is in the future and so it infact delays garbage collection.
Pre-aging the 'hosts' is not really needed at this point anyway so we throw
out the loop and nlm_find_client which is no longer needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch makes nlm_traverse{locks,blocks,shares} and friends use a function
pointer rather than a "action" enum.
This function pointer is given two nlm_hosts (one given by the caller, the
other taken from the lock/block/share currently visited), and is free to do
with them as it wants. If it returns a non-zero value, the lockd/block/share
is released.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This changes struct nlm_file and the nlm_files hash table to use a hlist
instead of the home-grown lists.
This allows us to remove f_hash which was only used to find the right hash
chain to delete an entry from.
It also increases the size of the nlm_files hash table from 32 to 128.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
| |
This patch changes the nlm_blocked list to use a list_node instead of
homegrown linked list handling.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
| |
Get rid of the home-grown singly linked lists for the nlm_host hash table.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This converts the statd upcalls to use the nsm_handle
This means that we only register each host once with statd, rather than
registering each host/vers/protocol triple.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch makes the SM_NOTIFY handling understand and use the nsm_handle.
To make it a bit clear what is happening:
nlmclent_prepare_reclaim and nlmclnt_finish_reclaim
get open-coded into 'reclaimer'
The result is tidied up.
Then some of that functionality is moved out into nlm_host_rebooted (which
calls nlmclnt_recovery which starts a thread which runs reclaimer).
Also host_rebooted now finds an nsm_handle rather than a host, then then
iterates over all hosts and deals with each host that shares that nsm_handle.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch introduces the nsm_handle, which is shared by all nlm_host objects
referring to the same client.
With this patch applied, all nlm_hosts from the same address will share the
same nsm_handle. A future patch will add sharing by name.
Note: this patch changes h_name so that it is no longer guaranteed to be an IP
address of the host. When the host represents an NFS server, h_name will be
the name passed in the mount call. When the host represents a client, h_name
will be the name presented in the lock request received from the client. A
h_name is only used for printing informational messages, this change should
not be significant.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds the peer's hostname (and name length) to all calls to
nlm*_lookup_host functions. A subsequent patch will make use of these (is
requested by a sysctl).
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Common code from nlm4svc_proc_sm_notify and nlmsvc_proc_sm_notify is moved
into a new nlm_host_rebooted.
This is in preparation of a patch that will change the reboot notification
handling entirely.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Speed up high call-rate workloads by caching the struct ip_map for the peer on
the connected struct svc_sock instead of looking it up in the ip_map cache
hashtable on every call. This helps workloads using AUTH_SYS authentication
over TCP.
Testing was on a 4 CPU 4 NIC Altix using 4 IRIX clients, each with 16
synthetic client threads simulating an rsync (i.e. recursive directory
listing) workload reading from an i386 RH9 install image (161480 regular files
in 10841 directories) on the server. That tree is small enough to fill in the
server's RAM so no disk traffic was involved. This setup gives a sustained
call rate in excess of 60000 calls/sec before being CPU-bound on the server.
Profiling showed strcmp(), called from ip_map_match(), was taking 4.8% of each
CPU, and ip_map_lookup() was taking 2.9%. This patch drops both contribution
into the profile noise.
Note that the above result overstates this value of this patch for most
workloads. The synthetic clients are all using separate IP addresses, so
there are 64 entries in the ip_map cache hash. Because the kernel measured
contained the bug fixed in commit
commit 1f1e030bf75774b6a283518e1534d598e14147d4
and was running on 64bit little-endian machine, probably all of those 64
entries were on a single chain, thus increasing the cost of ip_map_lookup().
With a modern kernel you would need more clients to see the same amount of
performance improvement. This patch has helped to scale knfsd to handle a
deployment with 2000 NFS clients.
Signed-off-by: Greg Banks <gnb@melbourne.sgi.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The max possible is the maximum RPC payload. The default depends on amount of
total memory.
The value can be set within reason as long as no nfsd threads are currently
running. The value can also be ready, allowing the default to be determined
after nfsd has started.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The limit over UDP remains at 32K. Also, make some of the apparently
arbitrary sizing constants clearer.
The biggest change here involves replacing NFSSVC_MAXBLKSIZE by a function of
the rqstp. This allows it to be different for different protocols (udp/tcp)
and also allows it to depend on the servers declared sv_bufsiz.
Note that we don't actually increase sv_bufsz for nfs yet. That comes next.
Signed-off-by: Greg Banks <gnb@melbourne.sgi.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
.. by allocating the array of 'kvec' in 'struct svc_rqst'.
As we plan to increase RPCSVC_MAXPAGES from 8 upto 256, we can no longer
allocate an array of this size on the stack. So we allocate it in 'struct
svc_rqst'.
However svc_rqst contains (indirectly) an array of the same type and size
(actually several, but they are in a union). So rather than waste space, we
move those arrays out of the separately allocated union and into svc_rqst to
share with the kvec moved out of svc_tcp_recvfrom (various arrays are used at
different times, so there is no conflict).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We are planning to increase RPCSVC_MAXPAGES from about 8 to about 256. This
means we need to be a bit careful about arrays of size RPCSVC_MAXPAGES.
struct svc_rqst contains two such arrays. However the there are never more
that RPCSVC_MAXPAGES pages in the two arrays together, so only one array is
needed.
The two arrays are for the pages holding the request, and the pages holding
the reply. Instead of two arrays, we can simply keep an index into where the
first reply page is.
This patch also removes a number of small inline functions that probably
server to obscure what is going on rather than clarify it, and opencode the
needed functionality.
Also remove the 'rq_restailpage' variable as it is *always* 0. i.e. if the
response 'xdr' structure has a non-empty tail it is always in the same pages
as the head.
check counters are initilised and incr properly
check for consistant usage of ++ etc
maybe extra some inlines for common approach
general review
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Magnus Maatta <novell@kiruna.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Driver for TI Flash Media card reader. At present, only MMC/SD cards are
supported.
[akpm@osdl.org: cleanups, build fixes]
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Cc: Daniel Qarras <dqarras@yahoo.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix paren-placement / precedence bug breaking initialization for 1 MHz
clock mode.
Also fix comment spelling error, and fence-post (off-by-one) error on
symbol used in request_region.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=7242
Thanks alexander.krause@erazor-zone.de, dzpost@dedekind.net, for the
reports and patch test, and phelps@mantara.com for the independent patch
and verification.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: <alexander.krause@erazor-zone.de>
Cc: <dzpost@dedekind.net>
Cc: <phelps@mantara.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- rename ____kmalloc to kmalloc_track_caller so that people have a chance
to guess what it does just from it's name. Add a comment describing it
for those who don't. Also move it after kmalloc in slab.h so people get
less confused when they are just looking for kmalloc - move things around
in slab.c a little to reduce the ifdef mess.
[penberg@cs.helsinki.fi: Fix up reversed #ifdef]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
| |
Fix headers_check #ifdef __KERNEL__ stuff.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
All-the-fault-of: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
|
|
|
|
|
| |
This allows numaq to properly align cpus to their given node during
boot. Pass logical apicid to apicid_to_node and allow the summit
sub-arch to use physical apicid (hard_smp_processor_id()).
Tested against numaq and summit based systems with no issues.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (39 commits)
Add missing maintainer countries in CREDITS
Fix bytes <-> kilobytes typo in Kconfig for ramdisk
fix a typo in Documentation/pi-futex.txt
BUG_ON conversion for fs/xfs/
BUG_ON() conversion in fs/nfsd/
BUG_ON conversion for fs/reiserfs
BUG_ON cleanups in arch/i386
BUG_ON cleanup in drivers/net/tokenring/
BUG_ON cleanup for drivers/md/
kerneldoc-typo in led-class.c
debugfs: spelling fix
rcutorture: Fix incorrect description of default for nreaders parameter
parport: Remove space in function calls
Michal Wronski: update contact info
Spelling fix: "control" instead of "cotrol"
reboot parameter in Documentation/kernel-parameters.txt
Fix copy&waste bug in comment in scripts/kernel-doc
remove duplicate "until" from kernel/workqueue.c
ite_gpio fix tabbage
fix file specification in comments
...
Fixed trivial path conflicts due to removed files:
arch/mips/dec/boot/decstation.c, drivers/char/ite_gpio.c
|
| |
| |
| |
| |
| |
| |
| | |
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix wreckage after removal of tickadj; convert to GENERIC_TIME.
[MIPS] DECstation defconfig update
[MIPS] Fix size of zones_size and zholes_size array
[MIPS] BCM1480: Mask pending interrupts against c0_status.im.
[MIPS] SB1250: Interrupt handler fixes
[MIPS] Remove IT8172-based platforms, ITE 8172G and Globespan IVR support.
[MIPS] Remove Atlas and SEAD from feature-removal-schedule.
[MIPS] Remove Jaguar and Ocelot family from feature list.
[MIPS] BCM1250: TRDY timeout tweaks for Broadcom SiByte systems
[MIPS] Remove dead DECstation boot code
[MIPS] Let gcc align 'struct pt_regs' on 8 bytes boundary
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
As per feature-removal-schedule.txt.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
It was obesrved that at least one older PCI card predating the
requirement for the TRDY signal to respond within 16 clock ticks actually
does not meet this rule nor even the power-on defaults of the PCI bridges
found in development systems built around the Broadcom SiByte SOCs. Here
is a patch that bumps up the timeout to the highest finite value supported
by these chips, which is 255 clock ticks. The bridges affected are the
SiByte SOC itself and the SP1011.
This change does not effectively affect systems only having PCI option
cards installed that meet the TRDY requirement of the current PCI spec.
The rule was introduced with PCI 2.1, so any older card may make the
system affected. If this is the case, performance of the system will
suffer in return for the card working at all. If this is a concern, then
the solution is not to use such cards.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The stack pointer in MIPS/gcc should always 8 bytes aligned on
entry to any routines. Therefore pt_regs structure must be
aligned to 8-byte boundary too.
Instead of creating dummy fields to achieve this alignment, this
patch let gcc doing it. Therefore 'smtc_pad' field can be safely
removed.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
VIDIOC_ENUM_FRAMESIZES and VIDIOC_ENUM_FRAMEINTERVALS ioctls are meant
to be used to provide better support for webcams. Currently, it is not yet
used on kernel drivers.
Better to keep it marked as experimental, until we have several kernel drivers
supporting those features.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add VIDIOC_ENUM_FRAMESIZES and VIDIOC_ENUM_FRAMEINTERVALS ioctls to enumerate
supported frame sizes and frame intervals.
Signed-off-by: Martin Rubli <martin.rubli@epfl.ch>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|/
|
|
|
|
|
|
| |
A generic change to cards to allow any board to specify whether
it needs the wm8775 module loaded (by the core) or not.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3848/1: pxafb: Add option of fixing video modes and spitz QVGA mode support
[ARM] 3880/1: remove the last trace of iop31x support
[ARM] 3879/1: ep93xx: instantiate platform devices for ep93xx ethernet
[ARM] 3809/3: get rid of 4 megabyte kernel image size limit
[ARM] Fix XIP_KERNEL build error in arch/arm/mm/mmu.c
[ARM] 3874/1: Remove leftover usage of asm/timeofday.h
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
support
Add the ability to have pxafb use only certain fixed video modes
(selected on a per platform basis). This is useful on production
hardware such as the Zaurus cxx00 models where the valid modes are
known in advance and any other modes could result in hardware damage.
Following this, add support for the cxx00 QVGA mode. Mode information
is passed to the lcd_power call to allowing the panel drivers to
configure the display hardware accordingly (corgi_lcd already contains
the functionality for the cxx00 panel).
This mirrors the setup already used by w100fb.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
| |
| |
| |
| | |
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial: (21 commits)
[SERIAL] add PNP IDs for FPI based touchscreens
[SERIAL] Magic SysRq SAK does nothing on serial consoles
[SERIAL] tickle NMI watchdog on serial output.
[SERIAL] Fix oops when removing suspended serial port
[SERIAL] Fix resume handling bug
[SERIAL] Remove wrong asm/serial.h inclusions
[SERIAL] CONFIG_PM=n slim: drivers/serial/8250_pci.c
[SERIAL] OMAP1510 serial fix for 115200 baud
[SERIAL] returning proper error from serial core driver
[SERIAL] Make uart_line_info() correctly tell MMIO from I/O port
[SERIAL] suspend/resume handlers don't have level arg anymore
[SERIAL] 8250 resourse management fixes
[SERIAL] serial_cs: Add quirk for brainboxes 2-port RS232 card
[SERIAL] serial_cs: handle Nokia multi->single port bodge via config quirk
[SERIAL] serial_cs: add configuration quirk
[SERIAL] serial_cs: Convert Oxford 950 / Possio GCC wakeup quirk
[SERIAL] serial_cs: convert IBM post-init handling to a quirk
[SERIAL] serial_cs: allow wildcarded quirks
[SERIAL] serial_cs: convert multi-port table to quirk table
[SERIAL] serial_cs: Use clean up multiport card detection
...
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Make sysrq-K work on serial console by passing in the tty.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
A serial card might have been removed when the system is resumed.
This results in a suspended port being shut down, which results in
the ports shutdown method being called twice in a row. This causes
BUGs. Avoid this by tracking the suspended state separately from
the initialised state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|