| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
| |
Support for specific hardware belongs under drivers/net/ not net/.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
| |
Any headers included by drivers should be under include/, and
any definitions they use are not really private to the core as
the name "dsa_priv.h" suggests.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
| |
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
| |
These drivers share a lot of code, so if we make them modular they
should be built into the same module. Therefore, link them together
and merge their respective module init and exit functions.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
The bit that tells us whether a statistics counter snapshot operation
has completed is located in the GLOBAL register block, not in the
GLOBAL2 register block, so fix up mv88e6xxx_stats_wait() to poll the
right register address.
Signed-off-by: Stephane Contri <Stephane.Contri@grassvalley.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
this warning:
net/dsa/mv88e6xxx.c: In function ‘mv88e6xxx_poll_link’:
net/dsa/mv88e6xxx.c:361: warning: ‘port_status’ may be used uninitialized in this function
triggers because GCC does not recognize the (correct) error flow
between 'link' and 'port_status'.
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for the Marvell 88E6131 switch chip. This chip only
supports the original (ethertype-less) DSA tagging format.
On the 88E6131, there is a PHY Polling Unit (PPU) which has exclusive
access to each of the PHYs's MII management registers. If we want to
talk to the PHYs from software, we have to disable the PPU and wait
for it to complete its current transaction before we can do so, and we
need to re-enable the PPU afterwards to make sure that the switch will
notice changes in link state and speed on the individual ports as they
occur.
Since disabling the PPU is rather slow, and since MII management
accesses are typically done in bursts, this patch keeps the PPU disabled
for 10ms after a software access completes. This makes handling the
PPU slightly more complex, but speeds up something like running ethtool
on one of the switch slave interfaces from ~300ms to ~30ms on typical
hardware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
