| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In order for the Fq_CoDel algorithm integrated in mac80211 layer to operate
effectively to control excessive queueing latency, the CoDel algorithm
requires an accurate measure of how long packets stays in the queue, AKA
sojourn time. The sojourn time measured at the mac80211 layer doesn't
include queueing latency in the lower layer (firmware/hardware) and CoDel
expects lower layer to have a short queue. However, most 802.11ac chipsets
offload tasks such TX aggregation to firmware or hardware, thus have a deep
lower layer queue.
Without a mechanism to control the lower layer queue size, packets only
stay in mac80211 layer transiently before being sent to firmware queue.
As a result, the sojourn time measured by CoDel in the mac80211 layer is
almost always lower than the CoDel latency target, hence CoDel does little
to control the latency, even when the lower layer queue causes excessive
latency.
The Byte Queue Limits (BQL) mechanism is commonly used to address the
similar issue with wired network interface. However, this method cannot be
applied directly to the wireless network interface. "Bytes" is not a
suitable measure of queue depth in the wireless network, as the data rate
can vary dramatically from station to station in the same network, from a
few Mbps to over Gbps.
This patch implements an Airtime-based Queue Limit (AQL) to make CoDel work
effectively with wireless drivers that utilized firmware/hardware
offloading. AQL allows each txq to release just enough packets to the lower
layer to form 1-2 large aggregations to keep hardware fully utilized and
retains the rest of the frames in mac80211 layer to be controlled by the
CoDel algorithm.
Signed-off-by: Kan Yan <kyan@google.com>
[ Toke: Keep API to set pending airtime internal, fix nits in commit msg ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-4-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
| |
If ieee80211_txq_setup_flows() fails, we don't clean up LED
state properly, leading to crashes later on, fix that.
Fixes: dc8b274f0952 ("mac80211: Move up init of TXQs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20191105154110.1ccf7112ba5d.I0ba865792446d051867b33153be65ce6b063d98c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
| |
Make it possibly for drivers to adjust the default max_mtu
by storing it in the hardware struct and using that value
for all interfaces.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/1567738137-31748-1-git-send-email-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
1) Drop IEEE80211_HW_EXT_KEY_ID_NATIVE and let drivers directly set
the NL80211_EXT_FEATURE_EXT_KEY_ID flag.
2) Drop IEEE80211_HW_NO_AMPDU_KEYBORDER_SUPPORT and simply assume all
drivers are unable to handle A-MPDU key borders.
The new Extended Key ID API now requires all mac80211 drivers to set
NL80211_EXT_FEATURE_EXT_KEY_ID when they implement set_key() and can
handle Extended Key ID. For drivers not providing set_key() mac80211
itself enables Extended Key ID support, using the internal SW crypto
services.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190629195015.19680-2-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
|
| |\
| | |
| | |
| | |
| | |
| | | |
Minor SPDX change conflict.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
ifa_list is protected by rcu, yet code doesn't reflect this.
Add the __rcu annotations and fix up all places that are now reported by
sparse.
I've done this in the same commit to not add intermediate patches that
result in new warnings.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\ \ \
| |_|/
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The WEP code in the mac80211 subsystem currently uses the crypto
API to access the arc4 (RC4) cipher, which is overly complicated,
and doesn't really have an upside in this particular case, since
ciphers are always synchronous and therefore always implemented in
software. Given that we have no accelerated software implementations
either, it is much more straightforward to invoke a generic library
interface directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
|
|
|
|
|
|
| |
Mac80211 SW crypto handles replacing PTK keys correctly.
Don't trigger needless warnings or workarounds when the driver can only
use the known good SW crypto provided by mac80211.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Only enable Extended Key ID support for drivers which are not supporting
crypto offload and also do not support A-MPDU.
While any driver using SW crypto from mac80211 is generally able to also
support Extended Key ID these drivers are likely to mix keyIDs in
AMPDUs when rekeying.
According to IEEE 802.11-2016 "9.7.3 A-MPDU contents" this is not
allowed.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[reword comment a bit, move ! into logic expression]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for Extended Key ID as defined in IEEE 802.11-2016.
- Implement the nl80211 API for Extended Key ID
- Extend mac80211 API to allow drivers to support Extended Key ID
- Enable Extended Key ID by default for drivers only supporting SW
crypto (e.g. mac80211_hwsim)
- Allow unicast Tx usage to be supressed (IEEE80211_KEY_FLAG_NO_AUTO_TX)
- Select the decryption key based on the MPDU keyid
- Enforce existing assumptions in the code that rekeys don't change the
cipher
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[remove module parameter]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When we did the original tests for the optimal value of sk_pacing_shift, we
came up with 6 ms of buffering as the default. Sadly, 6 is not a power of
two, so when picking the shift value I erred on the size of less buffering
and picked 4 ms instead of 8. This was probably wrong; those 2 ms of extra
buffering makes a larger difference than I thought.
So, change the default pacing shift to 7, which corresponds to 8 ms of
buffering. The point of diminishing returns really kicks in after 8 ms, and
so having this as a default should cut down on the need for extensive
per-device testing and overrides needed in the drivers.
Cc: stable@vger.kernel.org
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| |
| |
| |
| |
| |
| |
| | |
Set multi-bssid support flags according to driver support.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Allow user to override STBC configuration for Rx and Tx spatial streams.
In practice RX/TX STBC settings can be modified using appropriate
options in wpa_supplicant configuration file:
tx_stbc=-1..1
rx_stbc=-1..3
This functionality has been added to wpa_supplicant in commit cdeea70f59d0.
In FullMAC case these STBC options are passed to drivers by cfg80211
connect callback in fields of cfg80211_connect_params structure.
However for mac80211 drivers, e.g. for mac80211_hwsim,
overrides for STBC settings are ignored.
The reason why RX/TX STBC capabilities are not modified for mac80211
drivers is as follows. All drivers need to specify supported HT/VHT
overrides explicitly: see ht_capa_mod_mask and vht_capa_mod_mask fields
of wiphy structure. Only supported overrides will be passed to drivers by
cfg80211_connect and cfg80211_mlme_assoc operations: see bitwise 'AND'
performed by cfg80211_oper_and_ht_capa and cfg80211_oper_and_vht_capa.
This commit adds RX/TX STBC HT capabilities to mac80211_ht_capa_mod_mask,
allowing their modifications, as well as applies requested STBC
modifications in function ieee80211_apply_htcap_overrides.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This adds airtime accounting and scheduling to the mac80211 TXQ
scheduler. A new callback, ieee80211_sta_register_airtime(), is added
that drivers can call to report airtime usage for stations.
When airtime information is present, mac80211 will schedule TXQs
(through ieee80211_next_txq()) in a way that enforces airtime fairness
between active stations. This scheduling works the same way as the ath9k
in-driver airtime fairness scheduling. If no airtime usage is reported
by the driver, the scheduler will default to round-robin scheduling.
For drivers that don't control TXQ scheduling in software, a new API
function, ieee80211_txq_may_transmit(), is added which the driver can use
to check if the TXQ is eligible for transmission, or should be throttled to
enforce fairness. Calls to this function must also be enclosed in
ieee80211_txq_schedule_{start,end}() calls to ensure proper locking.
The API ieee80211_txq_may_transmit() also ensures that TXQ list will be
aligned aginst driver's own round-robin scheduler list. i.e it rotates
the TXQ list till it makes the requested node becomes the first entry
in TXQ list. Thus both the TXQ list and driver's list are in sync.
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Louie Lu <git@louie.lu>
[added debugfs write op to reset airtime counter]
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds an API to mac80211 to handle scheduling of TXQs. The interface
between driver and mac80211 for TXQ handling is changed by adding two new
functions: ieee80211_next_txq(), which will return the next TXQ to schedule
in the current round-robin rotation, and ieee80211_return_txq(), which the
driver uses to indicate that it has finished scheduling a TXQ (which will
then be put back in the scheduling rotation if it isn't empty).
The driver must call ieee80211_txq_schedule_start() at the start of each
scheduling session, and ieee80211_txq_schedule_end() at the end. The API
then guarantees that the same TXQ is not returned twice in the same
session (so a driver can loop on ieee80211_next_txq() without worrying
about breaking the loop.
Usage of the new API is optional, so drivers can be ported one at a time.
In this patch, the actual scheduling performed by mac80211 is simple
round-robin, but a subsequent commit adds airtime fairness awareness to the
scheduler.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[minor kernel-doc fix, propagate sparse locking checks out]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Recently TXQ teardown was moved earlier in ieee80211_unregister_hw(),
to avoid a use-after-free of the netdev data. However, interfaces
aren't fully removed at the point, and cfg80211_shutdown_all_interfaces
can for example, TX a deauth frame. Move the TXQ teardown to the
point between cfg80211_shutdown_all_interfaces and the free of
netdev queues, so we can be sure they are torn down before netdev
is freed, but after there is no ongoing TX.
Fixes: 77cfaf52eca5 ("mac80211: Run TXQ teardown code before de-registering interfaces")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|/
|
|
|
|
|
|
|
|
|
|
| |
This isn't really a problem now, but it means that the function
has a few NULL checks that are only relevant when coming from
the initial interface added in mac80211, and that's confusing.
Just pass non-NULL (but equivalently empty) in that case and
remove all the NULL checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
| |
Legacy-only devices are not very common and the overhead of the extra
code for HT and VHT rates is not big enough to justify all those extra
lines of code to make it optional.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
| |
Fix to return a negative error code -ENOMEM from the kmemdup
error handling case instead of 0.
Fixes: 09b4a4faf9d0 ("mac80211: introduce capability flags for VHT EXT NSS support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
| |
Make it possibly for drivers to adjust the default skb_pacing_shift
by storing it in the hardware struct.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[adjust commit log, move & adjust comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Depending on whether or not rate control supports selecting
rates depending on the bandwidth, we can use VHT extended
NSS support. In essence, this is dot11VHTExtendedNSSBWCapable
from the spec, since depending on that we'll need to parse
the bandwidth.
If needed, also set/clear the VHT Capability Element bit for
this capability so that we don't advertise it erroneously or
don't advertise it when we actually use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|\ |
|
| |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are quite a large number of fixes, notably:
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
We hit a problem with iwlwifi that was caused by a bug in
mac80211. A bug in iwlwifi caused the firwmare to crash in
certain cases in channel switch. Because of that bug,
drv_pre_channel_switch would fail and trigger the restart
flow.
Now we had the hw restart worker which runs on the system's
workqueue and the csa_connection_drop_work worker that runs
on mac80211's workqueue that can run together. This is
obviously problematic since the restart work wants to
reconfigure the connection, while the csa_connection_drop_work
worker does the exact opposite: it tries to disconnect.
Fix this by cancelling the csa_connection_drop_work worker
in the restart worker.
Note that this can sound racy: we could have:
driver iface_work CSA_work restart_work
+++++++++++++++++++++++++++++++++++++++++++++
|
<--drv_cs ---|
<FW CRASH!>
-CS FAILED-->
| |
| cancel_work(CSA)
schedule |
CSA work |
| |
Race between those 2
But this is not possible because we flush the workqueue
in the restart worker before we cancel the CSA worker.
That would be bullet proof if we could guarantee that
we schedule the CSA worker only from the iface_work
which runs on the workqueue (and not on the system's
workqueue), but unfortunately we do have an instance
in which we schedule the CSA work outside the context
of the workqueue (ieee80211_chswitch_done).
Note also that we should probably cancel other workers
like beacon_connection_loss_work and possibly others
for different types of interfaces, at the very least,
IBSS should suffer from the exact same problem, but for
now, do the minimum to fix the actual bug that was actually
experienced and reproduced.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The mod mask for VHT capabilities intends to say that you can override
the number of STBC receive streams, and it does, but only by accident.
The IEEE80211_VHT_CAP_RXSTBC_X aren't bits to be set, but values (albeit
left-shifted). ORing the bits together gets the right answer, but we
should use the _MASK macro here instead.
Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The TXQ teardown code can reference the vif data structures that are
stored in the netdev private memory area if there are still packets on
the queue when it is being freed. Since the TXQ teardown code is run
after the netdevs are freed, this can lead to a use-after-free. Fix this
by moving the TXQ teardown code to earlier in ieee80211_unregister_hw().
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|/ /
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Sometimes, it is required to stop the transmissions momentarily and
resume it later; stopping the txqs becomes very critical in scenarios where
the packet transmission has to be ceased completely. For example, during
the hardware restart, during off channel operations,
when initiating CSA(upon detecting a radar on the DFS channel), etc.
The TX queue stop/start logic in mac80211 works well in stopping the TX
when drivers make use of netdev queues, i.e, when Qdiscs in network layer
take care of traffic scheduling. Since the devices implementing
wake_tx_queue can run without Qdiscs, packets will be handed to mac80211
directly without queueing them in the netdev queues.
Also, mac80211 does not invoke any of the
netif_stop_*/netif_wake_* APIs if wake_tx_queue is implemented.
Since the queues are not stopped in this case, transmissions can continue
and this will impact negatively on the operation of the wireless device.
For example,
During hardware restart, we stop the netdev queues so that packets are
not sent to the driver. Since ath10k implements wake_tx_queue,
TX queues will not be stopped and packets might reach the hardware while
it is restarting; this can make hardware unresponsive and the only
possible option for recovery is to reboot the entire system.
There is another problem to this, it is observed that the packets
were sent on the DFS channel for a prolonged duration after radar
detection impacting the channel closing time.
We can still invoke netif stop/wake APIs when wake_tx_queue is implemented
but this could lead to packet drops in network layer; adding stop/start
logic for software TXQs in mac80211 instead makes more sense; the change
proposed adds the same in mac80211.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|\ \
| |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Small merge conflict in net/mac80211/scan.c, I preserved
the kcalloc() conversion. -DaveM
Johannes Berg says:
====================
This round's updates:
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add support for HE in mac80211 conforming with P802.11ax_D1.4.
Johannes: Fix another bug with the buf_size comparison in agg-rx.c.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Bump the IEEE80211_MAX_AMPDU_BUF size to 0x100 for HE support
and - for now - use IEEE80211_MAX_AMPDU_BUF_HT everywhere.
This is derived from my internal patch, parts of which Luca
had sent upstream.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Support the new random SN and minimal probe request contents
scan flags for the case of software scan - for hardware scan
the drivers need to opt in, but may need to do only that,
depending on their implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
On init, ieee80211_if_add() dumps the interface. Since that now includes a
dump of the TXQ state, we need to initialise that before the dump happens.
So move up the TXQ initialisation to to before the call to
ieee80211_if_add().
Fixes: 52539ca89f36 ("cfg80211: Expose TXQ stats and parameters to userspace")
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The kmalloc() function has a 2-factor argument form, kmalloc_array(). This
patch replaces cases of:
kmalloc(a * b, gfp)
with:
kmalloc_array(a * b, gfp)
as well as handling cases of:
kmalloc(a * b * c, gfp)
with:
kmalloc(array3_size(a, b, c), gfp)
as it's slightly less ugly than:
kmalloc_array(array_size(a, b), c, gfp)
This does, however, attempt to ignore constant size factors like:
kmalloc(4 * 1024, gfp)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
The tools/ directory was manually excluded, since it has its own
implementation of kmalloc().
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@
(
kmalloc(
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
kmalloc(
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@
(
kmalloc(
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
kmalloc(
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
kmalloc(
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
kmalloc(
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
kmalloc(
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
kmalloc(
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
kmalloc(
- sizeof(char) * COUNT
+ COUNT
, ...)
|
kmalloc(
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)
// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@
- kmalloc
+ kmalloc_array
(
- SIZE * COUNT
+ COUNT, SIZE
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
kmalloc(
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kmalloc(
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kmalloc(
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kmalloc(
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kmalloc(
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kmalloc(
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kmalloc(
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kmalloc(
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
kmalloc(
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kmalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kmalloc(
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kmalloc(
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kmalloc(
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
kmalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@
(
kmalloc(
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kmalloc(
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
kmalloc(C1 * C2 * C3, ...)
|
kmalloc(
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
kmalloc(
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
kmalloc(
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
kmalloc(
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@
(
kmalloc(sizeof(THING) * C2, ...)
|
kmalloc(sizeof(TYPE) * C2, ...)
|
kmalloc(C1 * C2 * C3, ...)
|
kmalloc(C1 * C2, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- kmalloc
+ kmalloc_array
(
- (E1) * E2
+ E1, E2
, ...)
|
- kmalloc
+ kmalloc_array
(
- (E1) * (E2)
+ E1, E2
, ...)
|
- kmalloc
+ kmalloc_array
(
- E1 * E2
+ E1, E2
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
|
|
|
|
|
|
| |
This adds support to mac80211 to export TXQ stats via the newly added
cfg80211 API.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
If userspace requested control port frames to go over 80211, then do so.
The control packets are intercepted just prior to delivery of the packet
to the underlying network device.
Pre-authentication type frames (protocol: 0x88c7) are also forwarded
over nl80211.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In the current implementation, mac80211 advertises the support of
AP_VLANs based on the driver's support for AP mode; it also
blocks encrypted AP_VLAN operation on devices advertising
SW_CRYPTO_CONTROL.
The implementation seems weird in it's current form and could be
often confusing, this is because there can be drivers advertising
both SW_CRYPTO_CONTROL and AP mode support (ex: ath10k) in which case
AP_VLAN will still be supported but only in open BSS and not in
secured BSS.
When SW_CRYPTO_CONTROL is enabled, it makes more sense if the decision
to support AP_VLANs is left to the driver. Mac80211 can then allow
AP_VLAN operations depending on the driver support.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
| |
This reverts commit e937b8da5a591f141fe41aa48a2e898df9888c95.
Turns out that a new driver (mt76) is coming in through
Kalle's tree, and will conflict with this. It also has some
conflicting requirements, so we'll revisit this later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
| |
This reverts commit b0d52ad821843a6c5badebd80feef9f871904fa6.
We need to revert the TXQ scheduling API due to conflicts
with a new driver, and this depends on that API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds airtime accounting and scheduling to the mac80211 TXQ
scheduler. A new hardware flag, AIRTIME_ACCOUNTING, is added that
drivers can set if they support reporting airtime usage of
transmissions. When this flag is set, mac80211 will expect the actual
airtime usage to be reported in the tx_time and rx_time fields of the
respective status structs.
When airtime information is present, mac80211 will schedule TXQs
(through ieee80211_next_txq()) in a way that enforces airtime fairness
between active stations. This scheduling works the same way as the ath9k
in-driver airtime fairness scheduling.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds an API to mac80211 to handle scheduling of TXQs and changes the
interface between driver and mac80211 for TXQ handling as follows:
- The wake_tx_queue callback interface no longer includes the TXQ. Instead,
the driver is expected to retrieve that from ieee80211_next_txq()
- Two new mac80211 functions are added: ieee80211_next_txq() and
ieee80211_schedule_txq(). The former returns the next TXQ that should be
scheduled, and is how the driver gets a queue to pull packets from. The
latter is called internally by mac80211 to start scheduling a queue, and
the driver is supposed to call it to re-schedule the TXQ after it is
finished pulling packets from it (unless the queue emptied).
The ath9k and ath10k drivers are changed to use the new API.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently the restart flow enables RX back, and then proceeds
to tear down RX and TX aggregations.
The TX aggregation tear down calls synchronize_net(), which
waits for packet receiving to be done.
This is done for every session, while RX processing is already
active, and in some reproductions it takes up to 3 seconds.
Add a call once in the restart_work, before we have traffic
active again, and remove the subsequent calls when tearing
down the aggregation.
This requires to move down the code that turns off the
reconfig flag in order to be able to test it in
_ieee80211_stop_tx_ba_session().
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
At least on iwlwifi, sometimes lockdep complains that we can
lock
chanctx_mtx -> mvm.mutex -> iflist_mtx
(due to iterate_interfaces)
and
iflist_mtx -> chanctx_mtx
Remove the latter dependency in mac80211 by using the RTNL
that we already hold in one case, and can relatively easily
achieve in the other case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
|
| |
In addition to keeping monitor interfaces on the regular list of
interfaces, keep those that are up and not in cooked mode on a
separate list. This saves having to iterate all interfaces when
delivering to monitor interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|