summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
blob: 1123cc6d56ef3d52bfa9dd455b1981600872dfc3 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
* Qualcomm NAND controller

Required properties:
- compatible:		must be one of the following:
    * "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x
			    SoC and it uses ADM DMA
    * "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in
                            IPQ4019 SoC and it uses BAM DMA
    * "qcom,ipq8074-nand" - for QPIC NAND controller v1.5.0 being used in
                            IPQ8074 SoC and it uses BAM DMA

- reg:			MMIO address range
- clocks:		must contain core clock and always on clock
- clock-names:		must contain "core" for the core clock and "aon" for the
			always on clock

EBI2 specific properties:
- dmas:			DMA specifier, consisting of a phandle to the ADM DMA
			controller node and the channel number to be used for
			NAND. Refer to dma.txt and qcom_adm.txt for more details
- dma-names:		must be "rxtx"
- qcom,cmd-crci:	must contain the ADM command type CRCI block instance
			number specified for the NAND controller on the given
			platform
- qcom,data-crci:	must contain the ADM data type CRCI block instance
			number specified for the NAND controller on the given
			platform

QPIC specific properties:
- dmas:			DMA specifier, consisting of a phandle to the BAM DMA
			and the channel number to be used for NAND. Refer to
			dma.txt, qcom_bam_dma.txt for more details
- dma-names:		must contain all 3 channel names : "tx", "rx", "cmd"
- #address-cells:	<1> - subnodes give the chip-select number
- #size-cells:		<0>

* NAND chip-select

Each controller may contain one or more subnodes to represent enabled
chip-selects which (may) contain NAND flash chips. Their properties are as
follows.

Required properties:
- reg:			a single integer representing the chip-select
			number (e.g., 0, 1, 2, etc.)
- #address-cells:	see partition.txt
- #size-cells:		see partition.txt

Optional properties:
- nand-bus-width:	see nand.txt
- nand-ecc-strength:	see nand.txt. If not specified, then ECC strength will
			be used according to chip requirement and available
			OOB size.

Each nandcs device node may optionally contain a 'partitions' sub-node, which
further contains sub-nodes describing the flash partition mapping. See
partition.txt for more detail.

Example:

nand-controller@1ac00000 {
	compatible = "qcom,ipq806x-nand";
	reg = <0x1ac00000 0x800>;

	clocks = <&gcc EBI2_CLK>,
		 <&gcc EBI2_AON_CLK>;
	clock-names = "core", "aon";

	dmas = <&adm_dma 3>;
	dma-names = "rxtx";
	qcom,cmd-crci = <15>;
	qcom,data-crci = <3>;

	#address-cells = <1>;
	#size-cells = <0>;

	nand@0 {
		reg = <0>;

		nand-ecc-strength = <4>;
		nand-bus-width = <8>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "boot-nand";
				reg = <0 0x58a0000>;
			};

			partition@58a0000 {
				label = "fs-nand";
				reg = <0x58a0000 0x4000000>;
			};
		};
	};
};

nand-controller@79b0000 {
	compatible = "qcom,ipq4019-nand";
	reg = <0x79b0000 0x1000>;

	clocks = <&gcc GCC_QPIC_CLK>,
		<&gcc GCC_QPIC_AHB_CLK>;
	clock-names = "core", "aon";

	dmas = <&qpicbam 0>,
		<&qpicbam 1>,
		<&qpicbam 2>;
	dma-names = "tx", "rx", "cmd";

	#address-cells = <1>;
	#size-cells = <0>;

	nand@0 {
		reg = <0>;
		nand-ecc-strength = <4>;
		nand-bus-width = <8>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "boot-nand";
				reg = <0 0x58a0000>;
			};

			partition@58a0000 {
				label = "fs-nand";
				reg = <0x58a0000 0x4000000>;
			};
		};
	};
};