1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
|
if ETRAX_ARCH_V32
config ETRAX_ETHERNET
bool "Ethernet support"
depends on ETRAX_ARCH_V32 && NETDEVICES
select MII
help
This option enables the ETRAX FS built-in 10/100Mbit Ethernet
controller.
config ETRAX_NO_PHY
bool "PHY not present"
depends on ETRAX_ETHERNET
help
This option disables all MDIO communication with an ethernet
transceiver connected to the MII interface. This option shall
typically be enabled if the MII interface is connected to a
switch. This option should normally be disabled. If enabled,
speed and duplex will be locked to 100 Mbit and full duplex.
config ETRAXFS_SERIAL
bool "Serial-port support"
depends on ETRAX_ARCH_V32
select SERIAL_CORE
select SERIAL_CORE_CONSOLE
help
Enables the ETRAX FS serial driver for ser0 (ttyS0)
You probably want this enabled.
config ETRAX_RS485
bool "RS-485 support"
depends on ETRAXFS_SERIAL
help
Enables support for RS-485 serial communication.
config ETRAX_RS485_DISABLE_RECEIVER
bool "Disable serial receiver"
depends on ETRAX_RS485
help
It is necessary to disable the serial receiver to avoid serial
loopback. Not all products are able to do this in software only.
config ETRAX_SERIAL_PORT0
bool "Serial port 0 enabled"
depends on ETRAXFS_SERIAL
help
Enables the ETRAX FS serial driver for ser0 (ttyS0)
Normally you want this on. You can control what DMA channels to use
if you do not need DMA to something else.
ser0 can use dma4 or dma6 for output and dma5 or dma7 for input.
config ETRAX_SERIAL_PORT1
bool "Serial port 1 enabled"
depends on ETRAXFS_SERIAL
help
Enables the ETRAX FS serial driver for ser1 (ttyS1).
config ETRAX_SERIAL_PORT2
bool "Serial port 2 enabled"
depends on ETRAXFS_SERIAL
help
Enables the ETRAX FS serial driver for ser2 (ttyS2).
config ETRAX_SERIAL_PORT3
bool "Serial port 3 enabled"
depends on ETRAXFS_SERIAL
help
Enables the ETRAX FS serial driver for ser3 (ttyS3).
config ETRAX_SYNCHRONOUS_SERIAL
bool "Synchronous serial-port support"
depends on ETRAX_ARCH_V32
help
Enables the ETRAX FS synchronous serial driver.
config ETRAX_SYNCHRONOUS_SERIAL_PORT0
bool "Synchronous serial port 0 enabled"
depends on ETRAX_SYNCHRONOUS_SERIAL
help
Enabled synchronous serial port 0.
config ETRAX_SYNCHRONOUS_SERIAL0_DMA
bool "Enable DMA on synchronous serial port 0."
depends on ETRAX_SYNCHRONOUS_SERIAL_PORT0
help
A synchronous serial port can run in manual or DMA mode.
Selecting this option will make it run in DMA mode.
config ETRAX_SYNCHRONOUS_SERIAL_PORT1
bool "Synchronous serial port 1 enabled"
depends on ETRAX_SYNCHRONOUS_SERIAL && ETRAXFS
help
Enabled synchronous serial port 1.
config ETRAX_SYNCHRONOUS_SERIAL1_DMA
bool "Enable DMA on synchronous serial port 1."
depends on ETRAX_SYNCHRONOUS_SERIAL_PORT1
help
A synchronous serial port can run in manual or DMA mode.
Selecting this option will make it run in DMA mode.
config ETRAX_AXISFLASHMAP
bool "Axis flash-map support"
depends on ETRAX_ARCH_V32
select MTD
select MTD_CFI
select MTD_CFI_AMDSTD
select MTD_JEDECPROBE
select MTD_BLOCK
select MTD_COMPLEX_MAPPINGS
select MTD_MTDRAM
help
This option enables MTD mapping of flash devices. Needed to use
flash memories. If unsure, say Y.
config ETRAX_AXISFLASHMAP_MTD0WHOLE
bool "MTD0 is whole boot flash device"
depends on ETRAX_AXISFLASHMAP
help
When this option is not set, mtd0 refers to the first partition
on the boot flash device. When set, mtd0 refers to the whole
device, with mtd1 referring to the first partition etc.
config ETRAX_PTABLE_SECTOR
int "Byte-offset of partition table sector"
depends on ETRAX_AXISFLASHMAP
default "65536"
help
Byte-offset of the partition table in the first flash chip.
The default value is 64kB and should not be changed unless
you know exactly what you are doing. The only valid reason
for changing this is when the flash block size is bigger
than 64kB (e.g. when using two parallel 16 bit flashes).
config ETRAX_NANDFLASH
bool "NAND flash support"
depends on ETRAX_ARCH_V32
select MTD_NAND
select MTD_NAND_IDS
help
This option enables MTD mapping of NAND flash devices. Needed to use
NAND flash memories. If unsure, say Y.
config ETRAX_NANDBOOT
bool "Boot from NAND flash"
depends on ETRAX_NANDFLASH
help
This options enables booting from NAND flash devices.
Say Y if your boot code, kernel and root file system is in
NAND flash. Say N if they are in NOR flash.
config ETRAX_GPIO
bool "GPIO support"
depends on ETRAX_ARCH_V32
---help---
Enables the ETRAX general port device (major 120, minors 0-4).
You can use this driver to access the general port bits. It supports
these ioctl's:
#include <linux/etraxgpio.h>
fd = open("/dev/gpioa", O_RDWR); // or /dev/gpiob
ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_SETBITS), bits_to_set);
ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_CLRBITS), bits_to_clear);
err = ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_READ_INBITS), &val);
Remember that you need to setup the port directions appropriately in
the General configuration.
config ETRAX_VIRTUAL_GPIO
bool "Virtual GPIO support"
depends on ETRAX_GPIO
help
Enables the virtual Etrax general port device (major 120, minor 6).
It uses an I/O expander for the I2C-bus.
config ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN
int "Virtual GPIO interrupt pin on PA pin"
range 0 7
depends on ETRAX_VIRTUAL_GPIO
help
The pin to use on PA for virtual gpio interrupt.
config ETRAX_PA_CHANGEABLE_DIR
hex "PA user changeable dir mask"
depends on ETRAX_GPIO
default "0x00" if ETRAXFS
default "0x00000000" if !ETRAXFS
help
This is a bitmask with information of what bits in PA that a
user can change direction on using ioctl's.
Bit set = changeable.
You probably want 0 here, but it depends on your hardware.
config ETRAX_PA_CHANGEABLE_BITS
hex "PA user changeable bits mask"
depends on ETRAX_GPIO
default "0x00" if ETRAXFS
default "0x00000000" if !ETRAXFS
help
This is a bitmask with information of what bits in PA
that a user can change the value on using ioctl's.
Bit set = changeable.
config ETRAX_PB_CHANGEABLE_DIR
hex "PB user changeable dir mask"
depends on ETRAX_GPIO
default "0x00000" if ETRAXFS
default "0x00000000" if !ETRAXFS
help
This is a bitmask with information of what bits in PB
that a user can change direction on using ioctl's.
Bit set = changeable.
You probably want 0 here, but it depends on your hardware.
config ETRAX_PB_CHANGEABLE_BITS
hex "PB user changeable bits mask"
depends on ETRAX_GPIO
default "0x00000" if ETRAXFS
default "0x00000000" if !ETRAXFS
help
This is a bitmask with information of what bits in PB
that a user can change the value on using ioctl's.
Bit set = changeable.
config ETRAX_PC_CHANGEABLE_DIR
hex "PC user changeable dir mask"
depends on ETRAX_GPIO
default "0x00000" if ETRAXFS
default "0x00000000" if !ETRAXFS
help
This is a bitmask with information of what bits in PC
that a user can change direction on using ioctl's.
Bit set = changeable.
You probably want 0 here, but it depends on your hardware.
config ETRAX_PC_CHANGEABLE_BITS
hex "PC user changeable bits mask"
depends on ETRAX_GPIO
default "0x00000" if ETRAXFS
default "0x00000000" if !ETRAXFS
help
This is a bitmask with information of what bits in PC
that a user can change the value on using ioctl's.
Bit set = changeable.
config ETRAX_PD_CHANGEABLE_DIR
hex "PD user changeable dir mask"
depends on ETRAX_GPIO && ETRAXFS
default "0x00000"
help
This is a bitmask with information of what bits in PD
that a user can change direction on using ioctl's.
Bit set = changeable.
You probably want 0x00000 here, but it depends on your hardware.
config ETRAX_PD_CHANGEABLE_BITS
hex "PD user changeable bits mask"
depends on ETRAX_GPIO && ETRAXFS
default "0x00000"
help
This is a bitmask (18 bits) with information of what bits in PD
that a user can change the value on using ioctl's.
Bit set = changeable.
config ETRAX_PE_CHANGEABLE_DIR
hex "PE user changeable dir mask"
depends on ETRAX_GPIO && ETRAXFS
default "0x00000"
help
This is a bitmask (18 bits) with information of what bits in PE
that a user can change direction on using ioctl's.
Bit set = changeable.
You probably want 0x00000 here, but it depends on your hardware.
config ETRAX_PE_CHANGEABLE_BITS
hex "PE user changeable bits mask"
depends on ETRAX_GPIO && ETRAXFS
default "0x00000"
help
This is a bitmask (18 bits) with information of what bits in PE
that a user can change the value on using ioctl's.
Bit set = changeable.
config ETRAX_PV_CHANGEABLE_DIR
hex "PV user changeable dir mask"
depends on ETRAX_VIRTUAL_GPIO
default "0x0000"
help
This is a bitmask (16 bits) with information of what bits in PV
that a user can change direction on using ioctl's.
Bit set = changeable.
You probably want 0x0000 here, but it depends on your hardware.
config ETRAX_PV_CHANGEABLE_BITS
hex "PV user changeable bits mask"
depends on ETRAX_VIRTUAL_GPIO
default "0x0000"
help
This is a bitmask (16 bits) with information of what bits in PV
that a user can change the value on using ioctl's.
Bit set = changeable.
config ETRAX_CARDBUS
bool "Cardbus support"
depends on ETRAX_ARCH_V32
help
Enabled the ETRAX Cardbus driver.
config PCI
bool
depends on ETRAX_CARDBUS
default y
select HAVE_GENERIC_DMA_COHERENT
config ETRAX_IOP_FW_LOAD
tristate "IO-processor hotplug firmware loading support"
depends on ETRAX_ARCH_V32
select FW_LOADER
help
Enables IO-processor hotplug firmware loading support.
config ETRAX_STREAMCOPROC
tristate "Stream co-processor driver enabled"
depends on ETRAX_ARCH_V32
help
This option enables a driver for the stream co-processor
for cryptographic operations.
config ETRAX_MMC_IOP
tristate "MMC/SD host driver using IO-processor"
depends on ETRAX_ARCH_V32 && MMC
help
This option enables the SD/MMC host controller interface.
The host controller is implemented using the built in
IO-Processor. Only the SPU is used in this implementation.
config ETRAX_SPI_MMC
# Make this one of several "choices" (possible simultaneously but
# suggested uniquely) when an IOP driver emerges for "real" MMC/SD
# protocol support.
tristate
depends on !ETRAX_MMC_IOP
default MMC
select SPI
select MMC_SPI
# While the board info is MMC_SPI only, the drivers are written to be
# independent of MMC_SPI, so we'll keep SPI non-dependent on the
# MMC_SPI config choices (well, except for a single depends-on-line
# for the board-info file until a separate non-MMC SPI board file
# emerges).
# FIXME: When that happens, we'll need to be able to ask for and
# configure non-MMC SPI ports together with MMC_SPI ports (if multiple
# SPI ports are enabled).
config SPI_ETRAX_SSER
tristate
depends on SPI_MASTER && ETRAX_ARCH_V32
select SPI_BITBANG
help
This enables using an synchronous serial (sser) port as a
SPI master controller on Axis ETRAX FS and later. The
driver can be configured to use any sser port.
config SPI_ETRAX_GPIO
tristate
depends on SPI_MASTER && ETRAX_ARCH_V32
select SPI_BITBANG
help
This enables using GPIO pins port as a SPI master controller
on Axis ETRAX FS and later. The driver can be configured to
use any GPIO pins.
config ETRAX_SPI_SSER0
tristate "SPI using synchronous serial port 0 (sser0)"
depends on ETRAX_SPI_MMC
default m if MMC_SPI=m
default y if MMC_SPI=y
default y if MMC_SPI=n
select SPI_ETRAX_SSER
help
Say Y for an MMC/SD socket connected to synchronous serial port 0,
or for devices using the SPI protocol on that port. Say m if you
want to build it as a module, which will be named spi_crisv32_sser.
(You need to select MMC separately.)
config ETRAX_SPI_SSER1
tristate "SPI using synchronous serial port 1 (sser1)"
depends on ETRAX_SPI_MMC
default m if MMC_SPI=m && ETRAX_SPI_SSER0=n
default y if MMC_SPI=y && ETRAX_SPI_SSER0=n
default y if MMC_SPI=n && ETRAX_SPI_SSER0=n
select SPI_ETRAX_SSER
help
Say Y for an MMC/SD socket connected to synchronous serial port 1,
or for devices using the SPI protocol on that port. Say m if you
want to build it as a module, which will be named spi_crisv32_sser.
(You need to select MMC separately.)
config ETRAX_SPI_GPIO
tristate "Bitbanged SPI using gpio pins"
depends on ETRAX_SPI_MMC
select SPI_ETRAX_GPIO
default m if MMC_SPI=m && ETRAX_SPI_SSER0=n && ETRAX_SPI_SSER1=n
default y if MMC_SPI=y && ETRAX_SPI_SSER0=n && ETRAX_SPI_SSER1=n
default y if MMC_SPI=n && ETRAX_SPI_SSER0=n && ETRAX_SPI_SSER1=n
help
Say Y for an MMC/SD socket connected to general I/O pins (but not
a complete synchronous serial ports), or for devices using the SPI
protocol on general I/O pins. Slow and slows down the system.
Say m to build it as a module, which will be called spi_crisv32_gpio.
(You need to select MMC separately.)
endif
|