1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
|
/*
* This is used to for host and peripheral modes of the driver for
* Inventra (Multidrop) Highspeed Dual-Role Controllers: (M)HDRC.
*
* Board initialization should put one of these into dev->platform_data,
* probably on some platform_device named "musb_hdrc". It encapsulates
* key configuration differences between boards.
*/
/* The USB role is defined by the connector used on the board, so long as
* standards are being followed. (Developer boards sometimes won't.)
*/
enum musb_mode {
MUSB_UNDEFINED = 0,
MUSB_HOST, /* A or Mini-A connector */
MUSB_PERIPHERAL, /* B or Mini-B connector */
MUSB_OTG /* Mini-AB connector */
};
struct clk;
struct musb_hdrc_eps_bits {
const char name[16];
u8 bits;
};
struct musb_hdrc_config {
/* MUSB configuration-specific details */
unsigned multipoint:1; /* multipoint device */
unsigned dyn_fifo:1; /* supports dynamic fifo sizing */
unsigned soft_con:1; /* soft connect required */
unsigned utm_16:1; /* utm data witdh is 16 bits */
unsigned big_endian:1; /* true if CPU uses big-endian */
unsigned mult_bulk_tx:1; /* Tx ep required for multbulk pkts */
unsigned mult_bulk_rx:1; /* Rx ep required for multbulk pkts */
unsigned high_iso_tx:1; /* Tx ep required for HB iso */
unsigned high_iso_rx:1; /* Rx ep required for HD iso */
unsigned dma:1; /* supports DMA */
unsigned vendor_req:1; /* vendor registers required */
u8 num_eps; /* number of endpoints _with_ ep0 */
u8 dma_channels; /* number of dma channels */
u8 dyn_fifo_size; /* dynamic size in bytes */
u8 vendor_ctrl; /* vendor control reg width */
u8 vendor_stat; /* vendor status reg witdh */
u8 dma_req_chan; /* bitmask for required dma channels */
u8 ram_bits; /* ram address size */
struct musb_hdrc_eps_bits *eps_bits;
};
struct musb_hdrc_platform_data {
/* MUSB_HOST, MUSB_PERIPHERAL, or MUSB_OTG */
u8 mode;
/* for clk_get() */
const char *clock;
/* (HOST or OTG) switch VBUS on/off */
int (*set_vbus)(struct device *dev, int is_on);
/* (HOST or OTG) mA/2 power supplied on (default = 8mA) */
u8 power;
/* (PERIPHERAL) mA/2 max power consumed (default = 100mA) */
u8 min_power;
/* (HOST or OTG) msec/2 after VBUS on till power good */
u8 potpgt;
/* Power the device on or off */
int (*set_power)(int state);
/* Turn device clock on or off */
int (*set_clock)(struct clk *clock, int is_on);
/* MUSB configuration-specific details */
struct musb_hdrc_config *config;
};
/* TUSB 6010 support */
#define TUSB6010_OSCCLK_60 16667 /* psec/clk @ 60.0 MHz */
#define TUSB6010_REFCLK_24 41667 /* psec/clk @ 24.0 MHz XI */
#define TUSB6010_REFCLK_19 52083 /* psec/clk @ 19.2 MHz CLKIN */
#ifdef CONFIG_ARCH_OMAP2
extern int __init tusb6010_setup_interface(
struct musb_hdrc_platform_data *data,
unsigned ps_refclk, unsigned waitpin,
unsigned async_cs, unsigned sync_cs,
unsigned irq, unsigned dmachan);
extern int tusb6010_platform_retime(unsigned is_refclk);
#endif /* OMAP2 */
|
