Merge branch 'ib-mfd-regulator-watchdog-6.11' into ibs-for-mfd-merged

14 files changed, 2094 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd96801-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd96801-pmic.yaml
new file mode 100644
index 000000000000..d381125a0a15
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd96801-pmic.yaml
@@ -0,0 +1,173 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rohm,bd96801-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD96801 Scalable Power Management Integrated Circuit
+
+maintainers:
+  - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description:
+  BD96801 is an automotive grade single-chip power management IC.
+  It integrates 4 buck converters and 3 LDOs with safety features like
+  over-/under voltage and over current detection and a watchdog.
+
+properties:
+  compatible:
+    const: rohm,bd96801
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    description:
+      The PMIC provides intb and errb IRQ lines. The errb IRQ line is used
+      for fatal IRQs which will cause the PMIC to shut down power outputs.
+      In many systems this will shut down the SoC contolling the PMIC and
+      connecting/handling the errb can be omitted. However, there are cases
+      where the SoC is not powered by the PMIC or has a short time backup
+      energy to handle shutdown of critical hardware. In that case it may be
+      useful to connect the errb and handle errb events.
+    minItems: 1
+    maxItems: 2
+
+  interrupt-names:
+    minItems: 1
+    items:
+      - enum: [intb, errb]
+      - const: errb
+
+  rohm,hw-timeout-ms:
+    description:
+      Watchdog timeout value(s). First walue is timeout limit. Second value is
+      optional value for 'too early' watchdog ping if window timeout mode is
+      to be used.
+    minItems: 1
+    maxItems: 2
+
+  rohm,wdg-action:
+    description:
+      Whether the watchdog failure must turn off the regulator power outputs or
+      just toggle the INTB line.
+    enum:
+      - prstb
+      - intb-only
+
+  timeout-sec:
+    maxItems: 2
+
+  regulators:
+    $ref: /schemas/regulator/rohm,bd96801-regulator.yaml
+    description:
+      List of child nodes that specify the regulators.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-names
+  - regulators
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/leds/common.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pmic: pmic@60 {
+            reg = <0x60>;
+            compatible = "rohm,bd96801";
+            interrupt-parent = <&gpio1>;
+            interrupts = <29 IRQ_TYPE_LEVEL_LOW>, <6 IRQ_TYPE_LEVEL_LOW>;
+            interrupt-names = "intb", "errb";
+
+            regulators {
+                buck1 {
+                    regulator-name = "buck1";
+                    regulator-ramp-delay = <1250>;
+                    /* 0.5V min INITIAL - 150 mV tune */
+                    regulator-min-microvolt = <350000>;
+                    /* 3.3V + 150mV tune */
+                    regulator-max-microvolt = <3450000>;
+
+                    /* These can be set only when PMIC is in STBY */
+                    rohm,initial-voltage-microvolt = <500000>;
+                    regulator-ov-error-microvolt = <230000>;
+                    regulator-uv-error-microvolt = <230000>;
+                    regulator-temp-protection-kelvin = <1>;
+                    regulator-temp-warn-kelvin = <0>;
+                };
+                buck2 {
+                    regulator-name = "buck2";
+                    regulator-min-microvolt = <350000>;
+                    regulator-max-microvolt = <3450000>;
+
+                    rohm,initial-voltage-microvolt = <3000000>;
+                    regulator-ov-error-microvolt = <18000>;
+                    regulator-uv-error-microvolt = <18000>;
+                    regulator-temp-protection-kelvin = <1>;
+                    regulator-temp-warn-kelvin = <1>;
+                };
+                buck3 {
+                    regulator-name = "buck3";
+                    regulator-min-microvolt = <350000>;
+                    regulator-max-microvolt = <3450000>;
+
+                    rohm,initial-voltage-microvolt = <600000>;
+                    regulator-ov-warn-microvolt = <18000>;
+                    regulator-uv-warn-microvolt = <18000>;
+                    regulator-temp-protection-kelvin = <1>;
+                    regulator-temp-error-kelvin = <0>;
+                };
+                buck4 {
+                    regulator-name = "buck4";
+                    regulator-min-microvolt = <350000>;
+                    regulator-max-microvolt = <3450000>;
+
+                    rohm,initial-voltage-microvolt = <600000>;
+                    regulator-ov-warn-microvolt = <18000>;
+                    regulator-uv-warn-microvolt = <18000>;
+                    regulator-temp-protection-kelvin = <1>;
+                    regulator-temp-error-kelvin = <0>;
+                };
+                ldo5 {
+                    regulator-name = "ldo5";
+                    regulator-min-microvolt = <300000>;
+                    regulator-max-microvolt = <3300000>;
+
+                    rohm,initial-voltage-microvolt = <500000>;
+                    regulator-ov-error-microvolt = <36000>;
+                    regulator-uv-error-microvolt = <34000>;
+                    regulator-temp-protection-kelvin = <1>;
+                    regulator-temp-warn-kelvin = <0>;
+                };
+                ldo6 {
+                    regulator-name = "ldo6";
+                    regulator-min-microvolt = <300000>;
+                    regulator-max-microvolt = <3300000>;
+
+                    rohm,initial-voltage-microvolt = <300000>;
+                    regulator-ov-error-microvolt = <36000>;
+                    regulator-uv-error-microvolt = <34000>;
+                    regulator-temp-protection-kelvin = <1>;
+                    regulator-temp-warn-kelvin = <0>;
+                };
+                ldo7 {
+                    regulator-name = "ldo7";
+                    regulator-min-microvolt = <300000>;
+                    regulator-max-microvolt = <3300000>;
+
+                    rohm,initial-voltage-microvolt = <500000>;
+                    regulator-ov-error-microvolt = <36000>;
+                    regulator-uv-error-microvolt = <34000>;
+                    regulator-temp-protection-kelvin = <1>;
+                    regulator-temp-warn-kelvin = <0>;
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd96801-regulator.yaml b/Documentation/devicetree/bindings/regulator/rohm,bd96801-regulator.yaml
new file mode 100644
index 000000000000..b3d2d7d583ce
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd96801-regulator.yaml
@@ -0,0 +1,63 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/rohm,bd96801-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD96801 Power Management Integrated Circuit regulators
+
+maintainers:
+  - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description:
+  This module is part of the ROHM BD96801 MFD device. For more details
+  see Documentation/devicetree/bindings/mfd/rohm,bd96801-pmic.yaml.
+
+  The regulator controller is represented as a sub-node of the PMIC node
+  on the device tree.
+
+  Regulator nodes should be named to buck_<number> and ldo_<number>.
+  The valid names for BD96801 regulator nodes are
+  buck1, buck2, buck3, buck4, ldo5, ldo6, ldo7
+
+patternProperties:
+  "^ldo[5-7]$":
+    type: object
+    description:
+      Properties for single LDO regulator.
+    $ref: regulator.yaml#
+
+    properties:
+      rohm,initial-voltage-microvolt:
+        description:
+          Initial voltage for regulator. Voltage can be tuned +/-150 mV from
+          this value. NOTE, This can be modified via I2C only when PMIC is in
+          STBY state.
+        minimum: 300000
+        maximum: 3300000
+
+    unevaluatedProperties: false
+
+  "^buck[1-4]$":
+    type: object
+    description:
+      Properties for single BUCK regulator.
+    $ref: regulator.yaml#
+
+    properties:
+      rohm,initial-voltage-microvolt:
+        description:
+          Initial voltage for regulator. Voltage can be tuned +/-150 mV from
+          this value. NOTE, This can be modified via I2C only when PMIC is in
+          STBY state.
+        minimum: 500000
+        maximum: 3300000
+
+      rohm,keep-on-stby:
+        description:
+          Keep the regulator powered when PMIC transitions to STBY state.
+        type: boolean
+
+    unevaluatedProperties: false
+
+additionalProperties: false
diff --git a/MAINTAINERS b/MAINTAINERS
index 5cf839bb43ff..17af347464d2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19472,17 +19472,21 @@ F:	drivers/gpio/gpio-bd71828.c
 F:	drivers/mfd/rohm-bd71828.c
 F:	drivers/mfd/rohm-bd718x7.c
 F:	drivers/mfd/rohm-bd9576.c
+F:	drivers/mfd/rohm-bd96801.c
 F:	drivers/regulator/bd71815-regulator.c
 F:	drivers/regulator/bd71828-regulator.c
 F:	drivers/regulator/bd718x7-regulator.c
 F:	drivers/regulator/bd9576-regulator.c
+F:	drivers/regulator/bd96801-regulator.c
 F:	drivers/regulator/rohm-regulator.c
 F:	drivers/rtc/rtc-bd70528.c
 F:	drivers/watchdog/bd9576_wdt.c
+F:	drivers/watchdog/bd96801_wdt.c
 F:	include/linux/mfd/rohm-bd71815.h
 F:	include/linux/mfd/rohm-bd71828.h
 F:	include/linux/mfd/rohm-bd718x7.h
 F:	include/linux/mfd/rohm-bd957x.h
+F:	include/linux/mfd/rohm-bd96801.h
 F:	include/linux/mfd/rohm-generic.h
 F:	include/linux/mfd/rohm-shared.h
 
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index abf745bba5f6..bc8be2e593b6 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -2101,6 +2101,19 @@ config MFD_ROHM_BD957XMUF
 	  BD9573MUF Power Management ICs. BD9576 and BD9573 are primarily
 	  designed to be used to power R-Car series processors.
 
+config MFD_ROHM_BD96801
+	tristate "ROHM BD96801 Power Management IC"
+	depends on I2C=y
+	depends on OF
+	select REGMAP_I2C
+	select REGMAP_IRQ
+	select MFD_CORE
+	help
+	  Select this option to get support for the ROHM BD96801 Power
+	  Management IC. The ROHM BD96801 is a highly scalable Power Management
+	  IC for industrial and automotive use. The BD96801 can be used as a
+	  master PMIC in a chained PMIC solution with suitable companion PMICs.
+
 config MFD_STM32_LPTIMER
 	tristate "Support for STM32 Low-Power Timer"
 	depends on (ARCH_STM32 && OF) || COMPILE_TEST
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index a02d17cb36f7..ce38d643009f 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -269,6 +269,7 @@ obj-$(CONFIG_RAVE_SP_CORE)	+= rave-sp.o
 obj-$(CONFIG_MFD_ROHM_BD71828)	+= rohm-bd71828.o
 obj-$(CONFIG_MFD_ROHM_BD718XX)	+= rohm-bd718x7.o
 obj-$(CONFIG_MFD_ROHM_BD957XMUF)	+= rohm-bd9576.o
+obj-$(CONFIG_MFD_ROHM_BD96801)	+= rohm-bd96801.o
 obj-$(CONFIG_MFD_STMFX) 	+= stmfx.o
 obj-$(CONFIG_MFD_KHADAS_MCU) 	+= khadas-mcu.o
 obj-$(CONFIG_MFD_ACER_A500_EC)	+= acer-ec-a500.o
diff --git a/drivers/mfd/rohm-bd96801.c b/drivers/mfd/rohm-bd96801.c
new file mode 100644
index 000000000000..714f08ed544b
--- /dev/null
+++ b/drivers/mfd/rohm-bd96801.c
@@ -0,0 +1,273 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2024 ROHM Semiconductors
+ *
+ * ROHM BD96801 PMIC driver
+ *
+ * This version of the "BD86801 scalable PMIC"'s driver supports only very
+ * basic set of the PMIC features. Most notably, there is no support for
+ * the ERRB interrupt and the configurations which should be done when the
+ * PMIC is in STBY mode.
+ *
+ * Supporting the ERRB interrupt would require dropping the regmap-IRQ
+ * usage or working around (or accepting a presense of) a naming conflict
+ * in debugFS IRQs.
+ *
+ * Being able to reliably do the configurations like changing the
+ * regulator safety limits (like limits for the over/under -voltages, over
+ * current, thermal protection) would require the configuring driver to be
+ * synchronized with entity causing the PMIC state transitions. Eg, one
+ * should be able to ensure the PMIC is in STBY state when the
+ * configurations are applied to the hardware. How and when the PMIC state
+ * transitions are to be done is likely to be very system specific, as will
+ * be the need to configure these safety limits. Hence it's not simple to
+ * come up with a generic solution.
+ *
+ * Users who require the ERRB handling and STBY state configurations can
+ * have a look at the original RFC:
+ * https://lore.kernel.org/all/cover.1712920132.git.mazziesaccount@gmail.com/
+ * which implements a workaround to debugFS naming conflict and some of
+ * the safety limit configurations - but leaves the state change handling
+ * and synchronization to be implemented.
+ *
+ * It would be great to hear (and receive a patch!) if you implement the
+ * STBY configuration support or a proper fix to the debugFS naming
+ * conflict in your downstream driver ;)
+ */
+
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/core.h>
+#include <linux/module.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+#include <linux/mfd/rohm-bd96801.h>
+#include <linux/mfd/rohm-generic.h>
+
+static const struct resource regulator_intb_irqs[] = {
+	DEFINE_RES_IRQ_NAMED(BD96801_TW_STAT, "bd96801-core-thermal"),
+
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK1_OCPH_STAT, "bd96801-buck1-overcurr-h"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK1_OCPL_STAT, "bd96801-buck1-overcurr-l"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK1_OCPN_STAT, "bd96801-buck1-overcurr-n"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK1_OVD_STAT, "bd96801-buck1-overvolt"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK1_UVD_STAT, "bd96801-buck1-undervolt"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK1_TW_CH_STAT, "bd96801-buck1-thermal"),
+
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK2_OCPH_STAT, "bd96801-buck2-overcurr-h"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK2_OCPL_STAT, "bd96801-buck2-overcurr-l"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK2_OCPN_STAT, "bd96801-buck2-overcurr-n"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK2_OVD_STAT, "bd96801-buck2-overvolt"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK2_UVD_STAT, "bd96801-buck2-undervolt"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK2_TW_CH_STAT, "bd96801-buck2-thermal"),
+
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK3_OCPH_STAT, "bd96801-buck3-overcurr-h"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK3_OCPL_STAT, "bd96801-buck3-overcurr-l"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK3_OCPN_STAT, "bd96801-buck3-overcurr-n"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK3_OVD_STAT, "bd96801-buck3-overvolt"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK3_UVD_STAT, "bd96801-buck3-undervolt"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK3_TW_CH_STAT, "bd96801-buck3-thermal"),
+
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK4_OCPH_STAT, "bd96801-buck4-overcurr-h"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK4_OCPL_STAT, "bd96801-buck4-overcurr-l"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK4_OCPN_STAT, "bd96801-buck4-overcurr-n"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK4_OVD_STAT, "bd96801-buck4-overvolt"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK4_UVD_STAT, "bd96801-buck4-undervolt"),
+	DEFINE_RES_IRQ_NAMED(BD96801_BUCK4_TW_CH_STAT, "bd96801-buck4-thermal"),
+
+	DEFINE_RES_IRQ_NAMED(BD96801_LDO5_OCPH_STAT, "bd96801-ldo5-overcurr"),
+	DEFINE_RES_IRQ_NAMED(BD96801_LDO5_OVD_STAT, "bd96801-ldo5-overvolt"),
+	DEFINE_RES_IRQ_NAMED(BD96801_LDO5_UVD_STAT, "bd96801-ldo5-undervolt"),
+
+	DEFINE_RES_IRQ_NAMED(BD96801_LDO6_OCPH_STAT, "bd96801-ldo6-overcurr"),
+	DEFINE_RES_IRQ_NAMED(BD96801_LDO6_OVD_STAT, "bd96801-ldo6-overvolt"),
+	DEFINE_RES_IRQ_NAMED(BD96801_LDO6_UVD_STAT, "bd96801-ldo6-undervolt"),
+
+	DEFINE_RES_IRQ_NAMED(BD96801_LDO7_OCPH_STAT, "bd96801-ldo7-overcurr"),
+	DEFINE_RES_IRQ_NAMED(BD96801_LDO7_OVD_STAT, "bd96801-ldo7-overvolt"),
+	DEFINE_RES_IRQ_NAMED(BD96801_LDO7_UVD_STAT, "bd96801-ldo7-undervolt"),
+};
+
+static const struct resource wdg_intb_irqs[] = {
+	DEFINE_RES_IRQ_NAMED(BD96801_WDT_ERR_STAT, "bd96801-wdg"),
+};
+
+static struct mfd_cell bd96801_cells[] = {
+	{
+		.name = "bd96801-wdt",
+		.resources = wdg_intb_irqs,
+		.num_resources = ARRAY_SIZE(wdg_intb_irqs),
+	}, {
+		.name = "bd96801-regulator",
+		.resources = regulator_intb_irqs,
+		.num_resources = ARRAY_SIZE(regulator_intb_irqs),
+	},
+};
+
+static const struct regmap_range bd96801_volatile_ranges[] = {
+	/* Status registers */
+	regmap_reg_range(BD96801_REG_WD_FEED, BD96801_REG_WD_FAILCOUNT),
+	regmap_reg_range(BD96801_REG_WD_ASK, BD96801_REG_WD_ASK),
+	regmap_reg_range(BD96801_REG_WD_STATUS, BD96801_REG_WD_STATUS),
+	regmap_reg_range(BD96801_REG_PMIC_STATE, BD96801_REG_INT_LDO7_INTB),
+	/* Registers which do not update value unless PMIC is in STBY */
+	regmap_reg_range(BD96801_REG_SSCG_CTRL, BD96801_REG_SHD_INTB),
+	regmap_reg_range(BD96801_REG_BUCK_OVP, BD96801_REG_BOOT_OVERTIME),
+	/*
+	 * LDO control registers have single bit (LDO MODE) which does not
+	 * change when we write it unless PMIC is in STBY. It's safer to not
+	 * cache it.
+	 */
+	regmap_reg_range(BD96801_LDO5_VOL_LVL_REG, BD96801_LDO7_VOL_LVL_REG),
+};
+
+static const struct regmap_access_table volatile_regs = {
+	.yes_ranges = bd96801_volatile_ranges,
+	.n_yes_ranges = ARRAY_SIZE(bd96801_volatile_ranges),
+};
+
+static const struct regmap_irq bd96801_intb_irqs[] = {
+	/* STATUS SYSTEM INTB */
+	REGMAP_IRQ_REG(BD96801_TW_STAT, 0, BD96801_TW_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_WDT_ERR_STAT, 0, BD96801_WDT_ERR_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_I2C_ERR_STAT, 0, BD96801_I2C_ERR_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_CHIP_IF_ERR_STAT, 0, BD96801_CHIP_IF_ERR_STAT_MASK),
+	/* STATUS BUCK1 INTB */
+	REGMAP_IRQ_REG(BD96801_BUCK1_OCPH_STAT, 1, BD96801_BUCK_OCPH_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK1_OCPL_STAT, 1, BD96801_BUCK_OCPL_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK1_OCPN_STAT, 1, BD96801_BUCK_OCPN_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK1_OVD_STAT, 1, BD96801_BUCK_OVD_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK1_UVD_STAT, 1, BD96801_BUCK_UVD_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK1_TW_CH_STAT, 1, BD96801_BUCK_TW_CH_STAT_MASK),
+	/* BUCK 2 INTB */
+	REGMAP_IRQ_REG(BD96801_BUCK2_OCPH_STAT, 2, BD96801_BUCK_OCPH_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK2_OCPL_STAT, 2, BD96801_BUCK_OCPL_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK2_OCPN_STAT, 2, BD96801_BUCK_OCPN_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK2_OVD_STAT, 2, BD96801_BUCK_OVD_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK2_UVD_STAT, 2, BD96801_BUCK_UVD_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK2_TW_CH_STAT, 2, BD96801_BUCK_TW_CH_STAT_MASK),
+	/* BUCK 3 INTB */
+	REGMAP_IRQ_REG(BD96801_BUCK3_OCPH_STAT, 3, BD96801_BUCK_OCPH_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK3_OCPL_STAT, 3, BD96801_BUCK_OCPL_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK3_OCPN_STAT, 3, BD96801_BUCK_OCPN_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK3_OVD_STAT, 3, BD96801_BUCK_OVD_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK3_UVD_STAT, 3, BD96801_BUCK_UVD_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK3_TW_CH_STAT, 3, BD96801_BUCK_TW_CH_STAT_MASK),
+	/* BUCK 4 INTB */
+	REGMAP_IRQ_REG(BD96801_BUCK4_OCPH_STAT, 4, BD96801_BUCK_OCPH_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK4_OCPL_STAT, 4, BD96801_BUCK_OCPL_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK4_OCPN_STAT, 4, BD96801_BUCK_OCPN_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK4_OVD_STAT, 4, BD96801_BUCK_OVD_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK4_UVD_STAT, 4, BD96801_BUCK_UVD_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_BUCK4_TW_CH_STAT, 4, BD96801_BUCK_TW_CH_STAT_MASK),
+	/* LDO5 INTB */
+	REGMAP_IRQ_REG(BD96801_LDO5_OCPH_STAT, 5, BD96801_LDO_OCPH_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_LDO5_OVD_STAT, 5, BD96801_LDO_OVD_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_LDO5_UVD_STAT, 5, BD96801_LDO_UVD_STAT_MASK),
+	/* LDO6 INTB */
+	REGMAP_IRQ_REG(BD96801_LDO6_OCPH_STAT, 6, BD96801_LDO_OCPH_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_LDO6_OVD_STAT, 6, BD96801_LDO_OVD_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_LDO6_UVD_STAT, 6, BD96801_LDO_UVD_STAT_MASK),
+	/* LDO7 INTB */
+	REGMAP_IRQ_REG(BD96801_LDO7_OCPH_STAT, 7, BD96801_LDO_OCPH_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_LDO7_OVD_STAT, 7, BD96801_LDO_OVD_STAT_MASK),
+	REGMAP_IRQ_REG(BD96801_LDO7_UVD_STAT, 7, BD96801_LDO_UVD_STAT_MASK),
+};
+
+static struct regmap_irq_chip bd96801_irq_chip_intb = {
+	.name = "bd96801-irq-intb",
+	.main_status = BD96801_REG_INT_MAIN,
+	.num_main_regs = 1,
+	.irqs = &bd96801_intb_irqs[0],
+	.num_irqs = ARRAY_SIZE(bd96801_intb_irqs),
+	.status_base = BD96801_REG_INT_SYS_INTB,
+	.mask_base = BD96801_REG_MASK_SYS_INTB,
+	.ack_base = BD96801_REG_INT_SYS_INTB,
+	.init_ack_masked = true,
+	.num_regs = 8,
+	.irq_reg_stride = 1,
+};
+
+static const struct regmap_config bd96801_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.volatile_table = &volatile_regs,
+	.cache_type = REGCACHE_RBTREE,
+};
+
+static int bd96801_i2c_probe(struct i2c_client *i2c)
+{
+	struct regmap_irq_chip_data *intb_irq_data;
+	const struct fwnode_handle *fwnode;
+	struct irq_domain *intb_domain;
+	struct regmap *regmap;
+	int ret, intb_irq;
+
+	fwnode = dev_fwnode(&i2c->dev);
+	if (!fwnode)
+		return dev_err_probe(&i2c->dev, -EINVAL, "Failed to find fwnode\n");
+
+	intb_irq = fwnode_irq_get_byname(fwnode, "intb");
+	if (intb_irq < 0)
+		return dev_err_probe(&i2c->dev, intb_irq, "INTB IRQ not configured\n");
+
+	regmap = devm_regmap_init_i2c(i2c, &bd96801_regmap_config);
+	if (IS_ERR(regmap))
+		return dev_err_probe(&i2c->dev, PTR_ERR(regmap),
+				    "Regmap initialization failed\n");
+
+	ret = regmap_write(regmap, BD96801_LOCK_REG, BD96801_UNLOCK);
+	if (ret)
+		return dev_err_probe(&i2c->dev, ret, "Failed to unlock PMIC\n");
+
+	ret = devm_regmap_add_irq_chip(&i2c->dev, regmap, intb_irq,
+				       IRQF_ONESHOT, 0, &bd96801_irq_chip_intb,
+				       &intb_irq_data);
+	if (ret)
+		return dev_err_probe(&i2c->dev, ret, "Failed to add INTB IRQ chip\n");
+
+	intb_domain = regmap_irq_get_domain(intb_irq_data);
+
+	ret = devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO,
+				   bd96801_cells,
+				   ARRAY_SIZE(bd96801_cells), NULL, 0,
+				   intb_domain);
+	if (ret)
+		dev_err(&i2c->dev, "Failed to create subdevices\n");
+
+	return ret;
+}
+
+static const struct of_device_id bd96801_of_match[] = {
+	{ .compatible = "rohm,bd96801",	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, bd96801_of_match);
+
+static struct i2c_driver bd96801_i2c_driver = {
+	.driver = {
+		.name = "rohm-bd96801",
+		.of_match_table = bd96801_of_match,
+	},
+	.probe = bd96801_i2c_probe,
+};
+
+static int __init bd96801_i2c_init(void)
+{
+	return i2c_add_driver(&bd96801_i2c_driver);
+}
+
+/* Initialise early so consumer devices can complete system boot */
+subsys_initcall(bd96801_i2c_init);
+
+static void __exit bd96801_i2c_exit(void)
+{
+	i2c_del_driver(&bd96801_i2c_driver);
+}
+module_exit(bd96801_i2c_exit);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("ROHM BD96801 Power Management IC driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 8385b57fe3dd..0a551cec1788 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -274,6 +274,18 @@ config REGULATOR_BD957XMUF
 	  This driver can also be built as a module. If so, the module
 	  will be called bd9576-regulator.
 
+config REGULATOR_BD96801
+	tristate "ROHM BD96801 Power Regulator"
+	depends on MFD_ROHM_BD96801
+	select REGULATOR_ROHM
+	help
+	  This driver supports voltage regulators on ROHM BD96801 PMIC.
+	  This will enable support for the software controllable buck
+	  and LDO regulators.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called bd96801-regulator.
+
 config REGULATOR_CPCAP
 	tristate "Motorola CPCAP regulator"
 	depends on MFD_CPCAP
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 4087765ee5d4..776d710b65c1 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_REGULATOR_BD718XX) += bd718x7-regulator.o
 obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
 obj-$(CONFIG_REGULATOR_BD957XMUF) += bd9576-regulator.o
 obj-$(CONFIG_REGULATOR_DA903X)	+= da903x-regulator.o
+obj-$(CONFIG_REGULATOR_BD96801) += bd96801-regulator.o
 obj-$(CONFIG_REGULATOR_DA9052)	+= da9052-regulator.o
 obj-$(CONFIG_REGULATOR_DA9055)	+= da9055-regulator.o
 obj-$(CONFIG_REGULATOR_DA9062)	+= da9062-regulator.o
diff --git a/drivers/regulator/bd96801-regulator.c b/drivers/regulator/bd96801-regulator.c
new file mode 100644
index 000000000000..46ca81f18703
--- /dev/null
+++ b/drivers/regulator/bd96801-regulator.c
@@ -0,0 +1,908 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2024 ROHM Semiconductors
+// bd96801-regulator.c ROHM BD96801 regulator driver
+
+/*
+ * This version of the "BD86801 scalable PMIC"'s driver supports only very
+ * basic set of the PMIC features. Most notably, there is no support for
+ * the ERRB interrupt and the configurations which should be done when the
+ * PMIC is in STBY mode.
+ *
+ * Supporting the ERRB interrupt would require dropping the regmap-IRQ
+ * usage or working around (or accepting a presense of) a naming conflict
+ * in debugFS IRQs.
+ *
+ * Being able to reliably do the configurations like changing the
+ * regulator safety limits (like limits for the over/under -voltages, over
+ * current, thermal protection) would require the configuring driver to be
+ * synchronized with entity causing the PMIC state transitions. Eg, one
+ * should be able to ensure the PMIC is in STBY state when the
+ * configurations are applied to the hardware. How and when the PMIC state
+ * transitions are to be done is likely to be very system specific, as will
+ * be the need to configure these safety limits. Hence it's not simple to
+ * come up with a generic solution.
+ *
+ * Users who require the ERRB handling and STBY state configurations can
+ * have a look at the original RFC:
+ * https://lore.kernel.org/all/cover.1712920132.git.mazziesaccount@gmail.com/
+ * which implements a workaround to debugFS naming conflict and some of
+ * the safety limit configurations - but leaves the state change handling
+ * and synchronization to be implemented.
+ *
+ * It would be great to hear (and receive a patch!) if you implement the
+ * STBY configuration support or a proper fix to the debugFS naming
+ * conflict in your downstream driver ;)
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/linear_range.h>
+#include <linux/mfd/rohm-generic.h>
+#include <linux/mfd/rohm-bd96801.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/coupler.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/slab.h>
+#include <linux/timer.h>
+
+enum {
+	BD96801_BUCK1,
+	BD96801_BUCK2,
+	BD96801_BUCK3,
+	BD96801_BUCK4,
+	BD96801_LDO5,
+	BD96801_LDO6,
+	BD96801_LDO7,
+	BD96801_REGULATOR_AMOUNT,
+};
+
+enum {
+	BD96801_PROT_OVP,
+	BD96801_PROT_UVP,
+	BD96801_PROT_OCP,
+	BD96801_PROT_TEMP,
+	BD96801_NUM_PROT,
+};
+
+#define BD96801_ALWAYS_ON_REG		0x3c
+#define BD96801_REG_ENABLE		0x0b
+#define BD96801_BUCK1_EN_MASK		BIT(0)
+#define BD96801_BUCK2_EN_MASK		BIT(1)
+#define BD96801_BUCK3_EN_MASK		BIT(2)
+#define BD96801_BUCK4_EN_MASK		BIT(3)
+#define BD96801_LDO5_EN_MASK		BIT(4)
+#define BD96801_LDO6_EN_MASK		BIT(5)
+#define BD96801_LDO7_EN_MASK		BIT(6)
+
+#define BD96801_BUCK1_VSEL_REG		0x28
+#define BD96801_BUCK2_VSEL_REG		0x29
+#define BD96801_BUCK3_VSEL_REG		0x2a
+#define BD96801_BUCK4_VSEL_REG		0x2b
+#define BD96801_LDO5_VSEL_REG		0x25
+#define BD96801_LDO6_VSEL_REG		0x26
+#define BD96801_LDO7_VSEL_REG		0x27
+#define BD96801_BUCK_VSEL_MASK		0x1F
+#define BD96801_LDO_VSEL_MASK		0xff
+
+#define BD96801_MASK_RAMP_DELAY		0xc0
+#define BD96801_INT_VOUT_BASE_REG	0x21
+#define BD96801_BUCK_INT_VOUT_MASK	0xff
+
+#define BD96801_BUCK_VOLTS		256
+#define BD96801_LDO_VOLTS		256
+
+#define BD96801_OVP_MASK		0x03
+#define BD96801_MASK_BUCK1_OVP_SHIFT	0x00
+#define BD96801_MASK_BUCK2_OVP_SHIFT	0x02
+#define BD96801_MASK_BUCK3_OVP_SHIFT	0x04
+#define BD96801_MASK_BUCK4_OVP_SHIFT	0x06
+#define BD96801_MASK_LDO5_OVP_SHIFT	0x00
+#define BD96801_MASK_LDO6_OVP_SHIFT	0x02
+#define BD96801_MASK_LDO7_OVP_SHIFT	0x04
+
+#define BD96801_PROT_LIMIT_OCP_MIN	0x00
+#define BD96801_PROT_LIMIT_LOW		0x01
+#define BD96801_PROT_LIMIT_MID		0x02
+#define BD96801_PROT_LIMIT_HI		0x03
+
+#define BD96801_REG_BUCK1_OCP		0x32
+#define BD96801_REG_BUCK2_OCP		0x32
+#define BD96801_REG_BUCK3_OCP		0x33
+#define BD96801_REG_BUCK4_OCP		0x33
+
+#define BD96801_MASK_BUCK1_OCP_SHIFT	0x00
+#define BD96801_MASK_BUCK2_OCP_SHIFT	0x04
+#define BD96801_MASK_BUCK3_OCP_SHIFT	0x00
+#define BD96801_MASK_BUCK4_OCP_SHIFT	0x04
+
+#define BD96801_REG_LDO5_OCP		0x34
+#define BD96801_REG_LDO6_OCP		0x34
+#define BD96801_REG_LDO7_OCP		0x34
+
+#define BD96801_MASK_LDO5_OCP_SHIFT	0x00
+#define BD96801_MASK_LDO6_OCP_SHIFT	0x02
+#define BD96801_MASK_LDO7_OCP_SHIFT	0x04
+
+#define BD96801_MASK_SHD_INTB		BIT(7)
+#define BD96801_INTB_FATAL		BIT(7)
+
+#define BD96801_NUM_REGULATORS		7
+#define BD96801_NUM_LDOS		4
+
+/*
+ * Ramp rates for bucks are controlled by bits [7:6] as follows:
+ * 00 => 1 mV/uS
+ * 01 => 5 mV/uS
+ * 10 => 10 mV/uS
+ * 11 => 20 mV/uS
+ */
+static const unsigned int buck_ramp_table[] = { 1000, 5000, 10000, 20000 };
+
+/*
+ * This is a voltage range that get's appended to selected
+ * bd96801_buck_init_volts value. The range from 0x0 to 0xF is actually
+ * bd96801_buck_init_volts + 0 ... bd96801_buck_init_volts + 150mV
+ * and the range from 0x10 to 0x1f is bd96801_buck_init_volts - 150mV ...
+ * bd96801_buck_init_volts - 0. But as the members of linear_range
+ * are all unsigned I will apply offset of -150 mV to value in
+ * linear_range - which should increase these ranges with
+ * 150 mV getting all the values to >= 0.
+ */
+static const struct linear_range bd96801_tune_volts[] = {
+	REGULATOR_LINEAR_RANGE(150000, 0x00, 0xF, 10000),
+	REGULATOR_LINEAR_RANGE(0, 0x10, 0x1F, 10000),
+};
+
+static const struct linear_range bd96801_buck_init_volts[] = {
+	REGULATOR_LINEAR_RANGE(500000 - 150000, 0x00, 0xc8, 5000),
+	REGULATOR_LINEAR_RANGE(1550000 - 150000, 0xc9, 0xec, 50000),
+	REGULATOR_LINEAR_RANGE(3300000 - 150000, 0xed, 0xff, 0),
+};
+
+static const struct linear_range bd96801_ldo_int_volts[] = {
+	REGULATOR_LINEAR_RANGE(300000, 0x00, 0x78, 25000),
+	REGULATOR_LINEAR_RANGE(3300000, 0x79, 0xff, 0),
+};
+
+#define BD96801_LDO_SD_VOLT_MASK	0x1
+#define BD96801_LDO_MODE_MASK		0x6
+#define BD96801_LDO_MODE_INT		0x0
+#define BD96801_LDO_MODE_SD		0x2
+#define BD96801_LDO_MODE_DDR		0x4
+
+static int ldo_ddr_volt_table[] = {500000, 300000};
+static int ldo_sd_volt_table[] = {3300000, 1800000};
+
+/* Constant IRQ initialization data (templates) */
+struct bd96801_irqinfo {
+	int type;
+	struct regulator_irq_desc irq_desc;
+	int err_cfg;
+	int wrn_cfg;
+	const char *irq_name;
+};
+
+#define BD96801_IRQINFO(_type, _name, _irqoff_ms, _irqname)	\
+{								\
+	.type = (_type),					\
+	.err_cfg = -1,						\
+	.wrn_cfg = -1,						\
+	.irq_name = (_irqname),					\
+	.irq_desc = {						\
+		.name = (_name),				\
+		.irq_off_ms = (_irqoff_ms),			\
+		.map_event = regulator_irq_map_event_simple,	\
+	},							\
+}
+
+static const struct bd96801_irqinfo buck1_irqinfo[] = {
+	BD96801_IRQINFO(BD96801_PROT_OCP, "buck1-over-curr-h", 500,
+			"bd96801-buck1-overcurr-h"),
+	BD96801_IRQINFO(BD96801_PROT_OCP, "buck1-over-curr-l", 500,
+			"bd96801-buck1-overcurr-l"),
+	BD96801_IRQINFO(BD96801_PROT_OCP, "buck1-over-curr-n", 500,
+			"bd96801-buck1-overcurr-n"),
+	BD96801_IRQINFO(BD96801_PROT_OVP, "buck1-over-voltage", 500,
+			"bd96801-buck1-overvolt"),
+	BD96801_IRQINFO(BD96801_PROT_UVP, "buck1-under-voltage", 500,
+			"bd96801-buck1-undervolt"),
+	BD96801_IRQINFO(BD96801_PROT_TEMP, "buck1-over-temp", 500,
+			"bd96801-buck1-thermal")
+};
+
+static const struct bd96801_irqinfo buck2_irqinfo[] = {
+	BD96801_IRQINFO(BD96801_PROT_OCP, "buck2-over-curr-h", 500,
+			"bd96801-buck2-overcurr-h"),
+	BD96801_IRQINFO(BD96801_PROT_OCP, "buck2-over-curr-l", 500,
+			"bd96801-buck2-overcurr-l"),
+	BD96801_IRQINFO(BD96801_PROT_OCP, "buck2-over-curr-n", 500,
+			"bd96801-buck2-overcurr-n"),
+	BD96801_IRQINFO(BD96801_PROT_OVP, "buck2-over-voltage", 500,
+			"bd96801-buck2-overvolt"),
+	BD96801_IRQINFO(BD96801_PROT_UVP, "buck2-under-voltage", 500,
+			"bd96801-buck2-undervolt"),
+	BD96801_IRQINFO(BD96801_PROT_TEMP, "buck2-over-temp", 500,
+			"bd96801-buck2-thermal")
+};
+
+static const struct bd96801_irqinfo buck3_irqinfo[] = {
+	BD96801_IRQINFO(BD96801_PROT_OCP, "buck3-over-curr-h", 500,
+			"bd96801-buck3-overcurr-h"),
+	BD96801_IRQINFO(BD96801_PROT_OCP, "buck3-over-curr-l", 500,
+			"bd96801-buck3-overcurr-l"),
+	BD96801_IRQINFO(BD96801_PROT_OCP, "buck3-over-curr-n", 500,
+			"bd96801-buck3-overcurr-n"),
+	BD96801_IRQINFO(BD96801_PROT_OVP, "buck3-over-voltage", 500,
+			"bd96801-buck3-overvolt"),
+	BD96801_IRQINFO(BD96801_PROT_UVP, "buck3-under-voltage", 500,
+			"bd96801-buck3-undervolt"),
+	BD96801_IRQINFO(BD96801_PROT_TEMP, "buck3-over-temp", 500,
+			"bd96801-buck3-thermal")
+};
+
+static const struct bd96801_irqinfo buck4_irqinfo[] = {
+	BD96801_IRQINFO(BD96801_PROT_OCP, "buck4-over-curr-h", 500,
+			"bd96801-buck4-overcurr-h"),
+	BD96801_IRQINFO(BD96801_PROT_OCP, "buck4-over-curr-l", 500,
+			"bd96801-buck4-overcurr-l"),
+	BD96801_IRQINFO(BD96801_PROT_OCP, "buck4-over-curr-n", 500,
+			"bd96801-buck4-overcurr-n"),
+	BD96801_IRQINFO(BD96801_PROT_OVP, "buck4-over-voltage", 500,
+			"bd96801-buck4-overvolt"),
+	BD96801_IRQINFO(BD96801_PROT_UVP, "buck4-under-voltage", 500,
+			"bd96801-buck4-undervolt"),
+	BD96801_IRQINFO(BD96801_PROT_TEMP, "buck4-over-temp", 500,
+			"bd96801-buck4-thermal")
+};
+
+static const struct bd96801_irqinfo ldo5_irqinfo[] = {
+	BD96801_IRQINFO(BD96801_PROT_OCP, "ldo5-overcurr", 500,
+			"bd96801-ldo5-overcurr"),
+	BD96801_IRQINFO(BD96801_PROT_OVP, "ldo5-over-voltage", 500,
+			"bd96801-ldo5-overvolt"),
+	BD96801_IRQINFO(BD96801_PROT_UVP, "ldo5-under-voltage", 500,
+			"bd96801-ldo5-undervolt"),
+};
+
+static const struct bd96801_irqinfo ldo6_irqinfo[] = {
+	BD96801_IRQINFO(BD96801_PROT_OCP, "ldo6-overcurr", 500,
+			"bd96801-ldo6-overcurr"),
+	BD96801_IRQINFO(BD96801_PROT_OVP, "ldo6-over-voltage", 500,
+			"bd96801-ldo6-overvolt"),
+	BD96801_IRQINFO(BD96801_PROT_UVP, "ldo6-under-voltage", 500,
+			"bd96801-ldo6-undervolt"),
+};
+
+static const struct bd96801_irqinfo ldo7_irqinfo[] = {
+	BD96801_IRQINFO(BD96801_PROT_OCP, "ldo7-overcurr", 500,
+			"bd96801-ldo7-overcurr"),
+	BD96801_IRQINFO(BD96801_PROT_OVP, "ldo7-over-voltage", 500,
+			"bd96801-ldo7-overvolt"),
+	BD96801_IRQINFO(BD96801_PROT_UVP, "ldo7-under-voltage", 500,
+			"bd96801-ldo7-undervolt"),
+};
+
+struct bd96801_irq_desc {
+	struct bd96801_irqinfo *irqinfo;
+	int num_irqs;
+};
+
+struct bd96801_regulator_data {
+	struct regulator_desc desc;
+	const struct linear_range *init_ranges;
+	int num_ranges;
+	struct bd96801_irq_desc irq_desc;
+	int initial_voltage;
+	int ldo_vol_lvl;
+	int ldo_errs;
+};
+
+struct bd96801_pmic_data {
+	struct bd96801_regulator_data regulator_data[BD96801_NUM_REGULATORS];
+	struct regmap *regmap;
+	int fatal_ind;
+};
+
+static int ldo_map_notif(int irq, struct regulator_irq_data *rid,
+			 unsigned long *dev_mask)
+{
+	int i;
+
+	for (i = 0; i < rid->num_states; i++) {
+		struct bd96801_regulator_data *rdata;
+		struct regulator_dev *rdev;
+
+		rdev = rid->states[i].rdev;
+		rdata = container_of(rdev->desc, struct bd96801_regulator_data,
+				     desc);
+		rid->states[i].notifs = regulator_err2notif(rdata->ldo_errs);
+		rid->states[i].errors = rdata->ldo_errs;
+		*dev_mask |= BIT(i);
+	}
+	return 0;
+}
+
+static int bd96801_list_voltage_lr(struct regulator_dev *rdev,
+				   unsigned int selector)
+{
+	int voltage;
+	struct bd96801_regulator_data *data;
+
+	data = container_of(rdev->desc, struct bd96801_regulator_data, desc);
+
+	/*
+	 * The BD096801 has voltage setting in two registers. One giving the
+	 * "initial voltage" (can be changed only when regulator is disabled.
+	 * This driver caches the value and sets it only at startup. The other
+	 * register is voltage tuning value which applies -150 mV ... +150 mV
+	 * offset to the voltage.
+	 *
+	 * Note that the cached initial voltage stored in regulator data is
+	 * 'scaled down' by the 150 mV so that all of our tuning values are
+	 * >= 0. This is done because the linear_ranges uses unsigned values.
+	 *
+	 * As a result, we increase the tuning voltage which we get based on
+	 * the selector by the stored initial_voltage.
+	 */
+	voltage = regulator_list_voltage_linear_range(rdev, selector);
+	if (voltage < 0)
+		return voltage;
+
+	return voltage + data->initial_voltage;
+}
+
+
+static const struct regulator_ops bd96801_ldo_table_ops = {
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_table,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static const struct regulator_ops bd96801_buck_ops = {
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = bd96801_list_voltage_lr,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.set_ramp_delay = regulator_set_ramp_delay_regmap,
+};
+
+static const struct regulator_ops bd96801_ldo_ops = {
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static int buck_get_initial_voltage(struct regmap *regmap, struct device *dev,
+				    struct bd96801_regulator_data *data)
+{
+	int ret = 0, sel, initial_uv;
+	int reg = BD96801_INT_VOUT_BASE_REG + data->desc.id;
+
+	if (data->num_ranges) {
+		ret = regmap_read(regmap, reg, &sel);
+		sel &= BD96801_BUCK_INT_VOUT_MASK;
+
+		ret = linear_range_get_value_array(data->init_ranges,
+						   data->num_ranges, sel,
+						   &initial_uv);
+		if (ret)
+			return ret;
+
+		data->initial_voltage = initial_uv;
+		dev_dbg(dev, "Tune-scaled initial voltage %u\n",
+			data->initial_voltage);
+	}
+
+	return 0;
+}
+
+static int get_ldo_initial_voltage(struct regmap *regmap,
+				   struct device *dev,
+				   struct bd96801_regulator_data *data)
+{
+	int ret;
+	int cfgreg;
+
+	ret = regmap_read(regmap, data->ldo_vol_lvl, &cfgreg);
+	if (ret)
+		return ret;
+
+	switch (cfgreg & BD96801_LDO_MODE_MASK) {
+	case BD96801_LDO_MODE_DDR:
+		data->desc.volt_table = ldo_ddr_volt_table;
+		data->desc.n_voltages = ARRAY_SIZE(ldo_ddr_volt_table);
+		break;
+	case BD96801_LDO_MODE_SD:
+		data->desc.volt_table = ldo_sd_volt_table;
+		data->desc.n_voltages = ARRAY_SIZE(ldo_sd_volt_table);
+		break;
+	default:
+		dev_info(dev, "Leaving LDO to normal mode");
+		return 0;
+	}
+
+	/* SD or DDR mode => override default ops */
+	data->desc.ops = &bd96801_ldo_table_ops,
+	data->desc.vsel_mask = 1;
+	data->desc.vsel_reg = data->ldo_vol_lvl;
+
+	return 0;
+}
+
+static int get_initial_voltage(struct device *dev, struct regmap *regmap,
+			struct bd96801_regulator_data *data)
+{
+	/* BUCK */
+	if (data->desc.id <= BD96801_BUCK4)
+		return buck_get_initial_voltage(regmap, dev, data);
+
+	/* LDO */
+	return get_ldo_initial_voltage(regmap, dev, data);
+}
+
+static int bd96801_walk_regulator_dt(struct device *dev, struct regmap *regmap,
+				     struct bd96801_regulator_data *data,
+				     int num)
+{
+	int i, ret;
+	struct device_node *np;
+	struct device_node *nproot = dev->parent->of_node;
+
+	nproot = of_get_child_by_name(nproot, "regulators");
+	if (!nproot) {
+		dev_err(dev, "failed to find regulators node\n");
+		return -ENODEV;
+	}
+	for_each_child_of_node(nproot, np)
+		for (i = 0; i < num; i++) {
+			if (!of_node_name_eq(np, data[i].desc.of_match))
+				continue;
+			/*
+			 * If STBY configs are supported, we must pass node
+			 * here to extract the initial voltages from the DT.
+			 * Thus we do the initial voltage getting in this
+			 * loop.
+			 */
+			ret = get_initial_voltage(dev, regmap, &data[i]);
+			if (ret) {
+				dev_err(dev,
+					"Initializing voltages for %s failed\n",
+					data[i].desc.name);
+				of_node_put(np);
+				of_node_put(nproot);
+
+				return ret;
+			}
+			if (of_property_read_bool(np, "rohm,keep-on-stby")) {
+				ret = regmap_set_bits(regmap,
+						      BD96801_ALWAYS_ON_REG,
+						      1 << data[i].desc.id);
+				if (ret) {
+					dev_err(dev,
+						"failed to set %s on-at-stby\n",
+						data[i].desc.name);
+					of_node_put(np);
+					of_node_put(nproot);
+
+					return ret;
+				}
+			}
+		}
+	of_node_put(nproot);
+
+	return 0;
+}
+
+/*
+ * Template for regulator data. Probe will allocate dynamic / driver instance
+ * struct so we should be on a safe side even if there were multiple PMICs to
+ * control. Note that there is a plan to allow multiple PMICs to be used so
+ * systems can scale better. I am however still slightly unsure how the
+ * multi-PMIC case will be handled. I don't know if the processor will have I2C
+ * acces to all of the PMICs or only the first one. I'd guess there will be
+ * access provided to all PMICs for voltage scaling - but the errors will only
+ * be informed via the master PMIC. Eg, we should prepare to support multiple
+ * driver instances - either with or without the IRQs... Well, let's first
+ * just support the simple and clear single-PMIC setup and ponder the multi PMIC
+ * case later. What we can easly do for preparing is to not use static global
+ * data for regulators though.
+ */
+static const struct bd96801_pmic_data bd96801_data = {
+	.regulator_data = {
+	{
+		.desc = {
+			.name = "buck1",
+			.of_match = of_match_ptr("buck1"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD96801_BUCK1,
+			.ops = &bd96801_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd96801_tune_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd96801_tune_volts),
+			.n_voltages = BD96801_BUCK_VOLTS,
+			.enable_reg = BD96801_REG_ENABLE,
+			.enable_mask = BD96801_BUCK1_EN_MASK,
+			.enable_is_inverted = true,
+			.vsel_reg = BD96801_BUCK1_VSEL_REG,
+			.vsel_mask = BD96801_BUCK_VSEL_MASK,
+			.ramp_reg = BD96801_BUCK1_VSEL_REG,
+			.ramp_mask = BD96801_MASK_RAMP_DELAY,
+			.ramp_delay_table = &buck_ramp_table[0],
+			.n_ramp_values = ARRAY_SIZE(buck_ramp_table),
+			.owner = THIS_MODULE,
+		},
+		.init_ranges = bd96801_buck_init_volts,
+		.num_ranges = ARRAY_SIZE(bd96801_buck_init_volts),
+		.irq_desc = {
+			.irqinfo = (struct bd96801_irqinfo *)&buck1_irqinfo[0],
+			.num_irqs = ARRAY_SIZE(buck1_irqinfo),
+		},
+	}, {
+		.desc = {
+			.name = "buck2",
+			.of_match = of_match_ptr("buck2"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD96801_BUCK2,
+			.ops = &bd96801_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd96801_tune_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd96801_tune_volts),
+			.n_voltages = BD96801_BUCK_VOLTS,
+			.enable_reg = BD96801_REG_ENABLE,
+			.enable_mask = BD96801_BUCK2_EN_MASK,
+			.enable_is_inverted = true,
+			.vsel_reg = BD96801_BUCK2_VSEL_REG,
+			.vsel_mask = BD96801_BUCK_VSEL_MASK,
+			.ramp_reg = BD96801_BUCK2_VSEL_REG,
+			.ramp_mask = BD96801_MASK_RAMP_DELAY,
+			.ramp_delay_table = &buck_ramp_table[0],
+			.n_ramp_values = ARRAY_SIZE(buck_ramp_table),
+			.owner = THIS_MODULE,
+		},
+		.irq_desc = {
+			.irqinfo = (struct bd96801_irqinfo *)&buck2_irqinfo[0],
+			.num_irqs = ARRAY_SIZE(buck2_irqinfo),
+		},
+		.init_ranges = bd96801_buck_init_volts,
+		.num_ranges = ARRAY_SIZE(bd96801_buck_init_volts),
+	}, {
+		.desc = {
+			.name = "buck3",
+			.of_match = of_match_ptr("buck3"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD96801_BUCK3,
+			.ops = &bd96801_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd96801_tune_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd96801_tune_volts),
+			.n_voltages = BD96801_BUCK_VOLTS,
+			.enable_reg = BD96801_REG_ENABLE,
+			.enable_mask = BD96801_BUCK3_EN_MASK,
+			.enable_is_inverted = true,
+			.vsel_reg = BD96801_BUCK3_VSEL_REG,
+			.vsel_mask = BD96801_BUCK_VSEL_MASK,
+			.ramp_reg = BD96801_BUCK3_VSEL_REG,
+			.ramp_mask = BD96801_MASK_RAMP_DELAY,
+			.ramp_delay_table = &buck_ramp_table[0],
+			.n_ramp_values = ARRAY_SIZE(buck_ramp_table),
+			.owner = THIS_MODULE,
+		},
+		.irq_desc = {
+			.irqinfo = (struct bd96801_irqinfo *)&buck3_irqinfo[0],
+			.num_irqs = ARRAY_SIZE(buck3_irqinfo),
+		},
+		.init_ranges = bd96801_buck_init_volts,
+		.num_ranges = ARRAY_SIZE(bd96801_buck_init_volts),
+	}, {
+		.desc = {
+			.name = "buck4",
+			.of_match = of_match_ptr("buck4"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD96801_BUCK4,
+			.ops = &bd96801_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd96801_tune_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd96801_tune_volts),
+			.n_voltages = BD96801_BUCK_VOLTS,
+			.enable_reg = BD96801_REG_ENABLE,
+			.enable_mask = BD96801_BUCK4_EN_MASK,
+			.enable_is_inverted = true,
+			.vsel_reg = BD96801_BUCK4_VSEL_REG,
+			.vsel_mask = BD96801_BUCK_VSEL_MASK,
+			.ramp_reg = BD96801_BUCK4_VSEL_REG,
+			.ramp_mask = BD96801_MASK_RAMP_DELAY,
+			.ramp_delay_table = &buck_ramp_table[0],
+			.n_ramp_values = ARRAY_SIZE(buck_ramp_table),
+			.owner = THIS_MODULE,
+		},
+		.irq_desc = {
+			.irqinfo = (struct bd96801_irqinfo *)&buck4_irqinfo[0],
+			.num_irqs = ARRAY_SIZE(buck4_irqinfo),
+		},
+		.init_ranges = bd96801_buck_init_volts,
+		.num_ranges = ARRAY_SIZE(bd96801_buck_init_volts),
+	}, {
+		.desc = {
+			.name = "ldo5",
+			.of_match = of_match_ptr("ldo5"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD96801_LDO5,
+			.ops = &bd96801_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd96801_ldo_int_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd96801_ldo_int_volts),
+			.n_voltages = BD96801_LDO_VOLTS,
+			.enable_reg = BD96801_REG_ENABLE,
+			.enable_mask = BD96801_LDO5_EN_MASK,
+			.enable_is_inverted = true,
+			.vsel_reg = BD96801_LDO5_VSEL_REG,
+			.vsel_mask = BD96801_LDO_VSEL_MASK,
+			.owner = THIS_MODULE,
+		},
+		.irq_desc = {
+			.irqinfo = (struct bd96801_irqinfo *)&ldo5_irqinfo[0],
+			.num_irqs = ARRAY_SIZE(ldo5_irqinfo),
+		},
+		.ldo_vol_lvl = BD96801_LDO5_VOL_LVL_REG,
+	}, {
+		.desc = {
+			.name = "ldo6",
+			.of_match = of_match_ptr("ldo6"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD96801_LDO6,
+			.ops = &bd96801_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd96801_ldo_int_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd96801_ldo_int_volts),
+			.n_voltages = BD96801_LDO_VOLTS,
+			.enable_reg = BD96801_REG_ENABLE,
+			.enable_mask = BD96801_LDO6_EN_MASK,
+			.enable_is_inverted = true,
+			.vsel_reg = BD96801_LDO6_VSEL_REG,
+			.vsel_mask = BD96801_LDO_VSEL_MASK,
+			.owner = THIS_MODULE,
+		},
+		.irq_desc = {
+			.irqinfo = (struct bd96801_irqinfo *)&ldo6_irqinfo[0],
+			.num_irqs = ARRAY_SIZE(ldo6_irqinfo),
+		},
+		.ldo_vol_lvl = BD96801_LDO6_VOL_LVL_REG,
+	}, {
+		.desc = {
+			.name = "ldo7",
+			.of_match = of_match_ptr("ldo7"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD96801_LDO7,
+			.ops = &bd96801_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd96801_ldo_int_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd96801_ldo_int_volts),
+			.n_voltages = BD96801_LDO_VOLTS,
+			.enable_reg = BD96801_REG_ENABLE,
+			.enable_mask = BD96801_LDO7_EN_MASK,
+			.enable_is_inverted = true,
+			.vsel_reg = BD96801_LDO7_VSEL_REG,
+			.vsel_mask = BD96801_LDO_VSEL_MASK,
+			.owner = THIS_MODULE,
+		},
+		.irq_desc = {
+			.irqinfo = (struct bd96801_irqinfo *)&ldo7_irqinfo[0],
+			.num_irqs = ARRAY_SIZE(ldo7_irqinfo),
+		},
+		.ldo_vol_lvl = BD96801_LDO7_VOL_LVL_REG,
+	},
+	},
+};
+
+static int initialize_pmic_data(struct device *dev,
+				struct bd96801_pmic_data *pdata)
+{
+	int r, i;
+
+	/*
+	 * Allocate and initialize IRQ data for all of the regulators. We
+	 * wish to modify IRQ information independently for each driver
+	 * instance.
+	 */
+	for (r = 0; r < BD96801_NUM_REGULATORS; r++) {
+		const struct bd96801_irqinfo *template;
+		struct bd96801_irqinfo *new;
+		int num_infos;
+
+		template = pdata->regulator_data[r].irq_desc.irqinfo;
+		num_infos = pdata->regulator_data[r].irq_desc.num_irqs;
+
+		new = devm_kcalloc(dev, num_infos, sizeof(*new), GFP_KERNEL);
+		if (!new)
+			return -ENOMEM;
+
+		pdata->regulator_data[r].irq_desc.irqinfo = new;
+
+		for (i = 0; i < num_infos; i++)
+			new[i] = template[i];
+	}
+
+	return 0;
+}
+
+static int bd96801_rdev_intb_irqs(struct platform_device *pdev,
+				  struct bd96801_pmic_data *pdata,
+				  struct bd96801_irqinfo *iinfo,
+				  struct regulator_dev *rdev)
+{
+	struct regulator_dev *rdev_arr[1];
+	void *retp;
+	int err = 0;
+	int irq;
+	int err_flags[] = {
+		[BD96801_PROT_OVP] = REGULATOR_ERROR_REGULATION_OUT,
+		[BD96801_PROT_UVP] = REGULATOR_ERROR_UNDER_VOLTAGE,
+		[BD96801_PROT_OCP] = REGULATOR_ERROR_OVER_CURRENT,
+		[BD96801_PROT_TEMP] = REGULATOR_ERROR_OVER_TEMP,
+
+	};
+	int wrn_flags[] = {
+		[BD96801_PROT_OVP] = REGULATOR_ERROR_OVER_VOLTAGE_WARN,
+		[BD96801_PROT_UVP] = REGULATOR_ERROR_UNDER_VOLTAGE_WARN,
+		[BD96801_PROT_OCP] = REGULATOR_ERROR_OVER_CURRENT_WARN,
+		[BD96801_PROT_TEMP] = REGULATOR_ERROR_OVER_TEMP_WARN,
+	};
+
+	/*
+	 * Don't install IRQ handler if both error and warning
+	 * notifications are explicitly disabled
+	 */
+	if (!iinfo->err_cfg && !iinfo->wrn_cfg)
+		return 0;
+
+	if (WARN_ON(iinfo->type >= BD96801_NUM_PROT))
+		return -EINVAL;
+
+	if (iinfo->err_cfg)
+		err = err_flags[iinfo->type];
+	else if (iinfo->wrn_cfg)
+		err = wrn_flags[iinfo->type];
+
+	iinfo->irq_desc.data = pdata;
+	irq = platform_get_irq_byname(pdev, iinfo->irq_name);
+	if (irq < 0)
+		return irq;
+	/* Find notifications for this IRQ (WARN/ERR) */
+
+	rdev_arr[0] = rdev;
+	retp = devm_regulator_irq_helper(&pdev->dev,
+					 &iinfo->irq_desc, irq,
+					 0, err, NULL, rdev_arr,
+					 1);
+	if (IS_ERR(retp))
+		return PTR_ERR(retp);
+
+	return 0;
+}
+
+
+
+static int bd96801_probe(struct platform_device *pdev)
+{
+	struct regulator_dev *ldo_errs_rdev_arr[BD96801_NUM_LDOS];
+	struct bd96801_regulator_data *rdesc;
+	struct regulator_config config = {};
+	int ldo_errs_arr[BD96801_NUM_LDOS];
+	struct bd96801_pmic_data *pdata;
+	int temp_notif_ldos = 0;
+	struct device *parent;
+	int i, ret;
+	void *retp;
+
+	parent = pdev->dev.parent;
+
+	pdata = devm_kmemdup(&pdev->dev, &bd96801_data, sizeof(bd96801_data),
+			     GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	if (initialize_pmic_data(&pdev->dev, pdata))
+		return -ENOMEM;
+
+	pdata->regmap = dev_get_regmap(parent, NULL);
+	if (!pdata->regmap) {
+		dev_err(&pdev->dev, "No register map found\n");
+		return -ENODEV;
+	}
+
+	rdesc = &pdata->regulator_data[0];
+
+	config.driver_data = pdata;
+	config.regmap = pdata->regmap;
+	config.dev = parent;
+
+	ret = bd96801_walk_regulator_dt(&pdev->dev, pdata->regmap, rdesc,
+					BD96801_NUM_REGULATORS);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < ARRAY_SIZE(pdata->regulator_data); i++) {
+		struct regulator_dev *rdev;
+		struct bd96801_irq_desc *idesc = &rdesc[i].irq_desc;
+		int j;
+
+		rdev = devm_regulator_register(&pdev->dev,
+					       &rdesc[i].desc, &config);
+		if (IS_ERR(rdev)) {
+			dev_err(&pdev->dev,
+				"failed to register %s regulator\n",
+				rdesc[i].desc.name);
+			return PTR_ERR(rdev);
+		}
+		/*
+		 * LDOs don't have own temperature monitoring. If temperature
+		 * notification was requested for this LDO from DT then we will
+		 * add the regulator to be notified if central IC temperature
+		 * exceeds threshold.
+		 */
+		if (rdesc[i].ldo_errs) {
+			ldo_errs_rdev_arr[temp_notif_ldos] = rdev;
+			ldo_errs_arr[temp_notif_ldos] = rdesc[i].ldo_errs;
+			temp_notif_ldos++;
+		}
+		if (!idesc)
+			continue;
+
+		/* Register INTB handlers for configured protections */
+		for (j = 0; j < idesc->num_irqs; j++) {
+			ret = bd96801_rdev_intb_irqs(pdev, pdata,
+						     &idesc->irqinfo[j], rdev);
+			if (ret)
+				return ret;
+		}
+	}
+	if (temp_notif_ldos) {
+		int irq;
+		struct regulator_irq_desc tw_desc = {
+			.name = "bd96801-core-thermal",
+			.irq_off_ms = 500,
+			.map_event = ldo_map_notif,
+		};
+
+		irq = platform_get_irq_byname(pdev, "bd96801-core-thermal");
+		if (irq < 0)
+			return irq;
+
+		retp = devm_regulator_irq_helper(&pdev->dev, &tw_desc, irq, 0,
+						 0, &ldo_errs_arr[0],
+						 &ldo_errs_rdev_arr[0],
+						 temp_notif_ldos);
+		if (IS_ERR(retp))
+			return PTR_ERR(retp);
+	}
+
+	return 0;
+}
+
+static const struct platform_device_id bd96801_pmic_id[] = {
+	{ "bd96801-regulator", },
+	{ }
+};
+MODULE_DEVICE_TABLE(platform, bd96801_pmic_id);
+
+static struct platform_driver bd96801_regulator = {
+	.driver = {
+		.name = "bd96801-pmic"
+	},
+	.probe = bd96801_probe,
+	.id_table = bd96801_pmic_id,
+};
+
+module_platform_driver(bd96801_regulator);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD96801 voltage regulator driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index 85eea38dbdf4..ceb3431f23b8 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -181,6 +181,19 @@ config BD957XMUF_WATCHDOG
 	  watchdog. Alternatively say M to compile the driver as a module,
 	  which will be called bd9576_wdt.
 
+config BD96801_WATCHDOG
+	tristate "ROHM BD96801 PMIC Watchdog"
+	depends on MFD_ROHM_BD96801
+	select WATCHDOG_CORE
+	help
+	  Support for the watchdog in the ROHM BD96801 PMIC. Watchdog can be
+	  configured to only generate IRQ or to trigger system reset via reset
+	  pin.
+
+	  Say Y here to include support for the ROHM BD96801 watchdog.
+	  Alternatively say M to compile the driver as a module,
+	  which will be called bd96801_wdt.
+
 config CROS_EC_WATCHDOG
 	tristate "ChromeOS EC-based watchdog"
 	select WATCHDOG_CORE
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index 2d1117564f5b..b51030f035a6 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -218,6 +218,7 @@ obj-$(CONFIG_XEN_WDT) += xen_wdt.o
 
 # Architecture Independent
 obj-$(CONFIG_BD957XMUF_WATCHDOG) += bd9576_wdt.o
+obj-$(CONFIG_BD96801_WATCHDOG) += bd96801_wdt.o
 obj-$(CONFIG_CROS_EC_WATCHDOG) += cros_ec_wdt.o
 obj-$(CONFIG_DA9052_WATCHDOG) += da9052_wdt.o
 obj-$(CONFIG_DA9055_WATCHDOG) += da9055_wdt.o
diff --git a/drivers/watchdog/bd96801_wdt.c b/drivers/watchdog/bd96801_wdt.c
new file mode 100644
index 000000000000..ff51f42ced2a
--- /dev/null
+++ b/drivers/watchdog/bd96801_wdt.c
@@ -0,0 +1,416 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2024 ROHM Semiconductors
+ *
+ * ROHM BD96801 watchdog driver
+ */
+
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/rohm-bd96801.h>
+#include <linux/mfd/rohm-generic.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reboot.h>
+#include <linux/regmap.h>
+#include <linux/watchdog.h>
+
+static bool nowayout;
+module_param(nowayout, bool, 0);
+MODULE_PARM_DESC(nowayout,
+		"Watchdog cannot be stopped once started (default=\"false\")");
+
+#define BD96801_WD_TMO_SHORT_MASK	0x70
+#define BD96801_WD_RATIO_MASK		0x3
+#define BD96801_WD_TYPE_MASK		0x4
+#define BD96801_WD_TYPE_SLOW		0x4
+#define BD96801_WD_TYPE_WIN		0x0
+
+#define BD96801_WD_EN_MASK		0x3
+#define BD96801_WD_IF_EN		0x1
+#define BD96801_WD_QA_EN		0x2
+#define BD96801_WD_DISABLE		0x0
+
+#define BD96801_WD_ASSERT_MASK		0x8
+#define BD96801_WD_ASSERT_RST		0x8
+#define BD96801_WD_ASSERT_IRQ		0x0
+
+#define BD96801_WD_FEED_MASK		0x1
+#define BD96801_WD_FEED			0x1
+
+/* 1.1 mS */
+#define FASTNG_MIN			11
+#define FASTNG_MAX_US			(100 * FASTNG_MIN << 7)
+#define SLOWNG_MAX_US			(16 * FASTNG_MAX_US)
+
+#define BD96801_WDT_DEFAULT_MARGIN_MS	1843
+/* Unit is seconds */
+#define DEFAULT_TIMEOUT 30
+
+/*
+ * BD96801 WDG supports window mode so the TMO consists of SHORT and LONG
+ * timeout values. SHORT time is meaningful only in window mode where feeding
+ * period shorter than SHORT would be an error. LONG time is used to detect if
+ * feeding is not occurring within given time limit (SoC SW hangs). The LONG
+ * timeout time is a multiple of (2, 4, 8 or 16 times) the SHORT timeout.
+ */
+
+struct wdtbd96801 {
+	struct device		*dev;
+	struct regmap		*regmap;
+	struct watchdog_device	wdt;
+};
+
+static int bd96801_wdt_ping(struct watchdog_device *wdt)
+{
+	struct wdtbd96801 *w = watchdog_get_drvdata(wdt);
+
+	return regmap_update_bits(w->regmap, BD96801_REG_WD_FEED,
+				  BD96801_WD_FEED_MASK, BD96801_WD_FEED);
+}
+
+static int bd96801_wdt_start(struct watchdog_device *wdt)
+{
+	struct wdtbd96801 *w = watchdog_get_drvdata(wdt);
+
+	return regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
+				  BD96801_WD_EN_MASK, BD96801_WD_IF_EN);
+}
+
+static int bd96801_wdt_stop(struct watchdog_device *wdt)
+{
+	struct wdtbd96801 *w = watchdog_get_drvdata(wdt);
+
+	return regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
+				  BD96801_WD_EN_MASK, BD96801_WD_DISABLE);
+}
+
+static const struct watchdog_info bd96801_wdt_info = {
+	.options	= WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING |
+			  WDIOF_SETTIMEOUT,
+	.identity	= "BD96801 Watchdog",
+};
+
+static const struct watchdog_ops bd96801_wdt_ops = {
+	.start		= bd96801_wdt_start,
+	.stop		= bd96801_wdt_stop,
+	.ping		= bd96801_wdt_ping,
+};
+
+static int find_closest_fast(unsigned int target, int *sel, unsigned int *val)
+{
+	unsigned int window = FASTNG_MIN;
+	int i;
+
+	for (i = 0; i < 8 && window < target; i++)
+		window <<= 1;
+
+	if (i == 8)
+		return -EINVAL;
+
+	*val = window;
+	*sel = i;
+
+	return 0;
+}
+
+static int find_closest_slow_by_fast(unsigned int fast_val, unsigned int *target,
+				     int *slowsel)
+{
+	static const int multipliers[] = {2, 4, 8, 16};
+	int sel;
+
+	for (sel = 0; sel < ARRAY_SIZE(multipliers) &&
+	     multipliers[sel] * fast_val < *target; sel++)
+		;
+
+	if (sel == ARRAY_SIZE(multipliers))
+		return -EINVAL;
+
+	*slowsel = sel;
+	*target = multipliers[sel] * fast_val;
+
+	return 0;
+}
+
+static int find_closest_slow(unsigned int *target, int *slow_sel, int *fast_sel)
+{
+	static const int multipliers[] = {2, 4, 8, 16};
+	unsigned int window = FASTNG_MIN;
+	unsigned int val = 0;
+	int i, j;
+
+	for (i = 0; i < 8; i++) {
+		for (j = 0; j < ARRAY_SIZE(multipliers); j++) {
+			unsigned int slow;
+
+			slow = window * multipliers[j];
+			if (slow >= *target && (!val || slow < val)) {
+				val = slow;
+				*fast_sel = i;
+				*slow_sel = j;
+			}
+		}
+		window <<= 1;
+	}
+	if (!val)
+		return -EINVAL;
+
+	*target = val;
+
+	return 0;
+}
+
+static int bd96801_set_wdt_mode(struct wdtbd96801 *w, unsigned int hw_margin,
+			       unsigned int hw_margin_min)
+{
+	int fastng, slowng, type, ret, reg, mask;
+	struct device *dev = w->dev;
+
+
+	if (hw_margin_min * 1000 > FASTNG_MAX_US) {
+		dev_err(dev, "Unsupported fast timeout %u uS [max %u]\n",
+			hw_margin_min * 1000, FASTNG_MAX_US);
+
+		return -EINVAL;
+	}
+
+	if (hw_margin * 1000 > SLOWNG_MAX_US) {
+		dev_err(dev, "Unsupported slow timeout %u uS [max %u]\n",
+			hw_margin * 1000, SLOWNG_MAX_US);
+
+		return -EINVAL;
+	}
+
+	/*
+	 * Convert to 100uS to guarantee reasonable timeouts fit in
+	 * 32bit maintaining also a decent accuracy.
+	 */
+	hw_margin *= 10;
+	hw_margin_min *= 10;
+
+	if (hw_margin_min) {
+		unsigned int min;
+
+		type = BD96801_WD_TYPE_WIN;
+		dev_dbg(dev, "Setting type WINDOW 0x%x\n", type);
+		ret = find_closest_fast(hw_margin_min, &fastng, &min);
+		if (ret)
+			return ret;
+
+		ret = find_closest_slow_by_fast(min, &hw_margin, &slowng);
+		if (ret) {
+			dev_err(dev,
+				"can't support slow timeout %u uS using fast %u uS. [max slow %u uS]\n",
+				hw_margin * 100, min * 100, min * 100 * 16);
+
+			return ret;
+		}
+		w->wdt.min_hw_heartbeat_ms = min / 10;
+	} else {
+		type = BD96801_WD_TYPE_SLOW;
+		dev_dbg(dev, "Setting type SLOW 0x%x\n", type);
+		ret = find_closest_slow(&hw_margin, &slowng, &fastng);
+		if (ret)
+			return ret;
+	}
+
+	w->wdt.max_hw_heartbeat_ms = hw_margin / 10;
+
+	fastng = FIELD_PREP(BD96801_WD_TMO_SHORT_MASK, fastng);
+
+	reg = slowng | fastng;
+	mask = BD96801_WD_RATIO_MASK | BD96801_WD_TMO_SHORT_MASK;
+	ret = regmap_update_bits(w->regmap, BD96801_REG_WD_TMO,
+				 mask, reg);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
+				 BD96801_WD_TYPE_MASK, type);
+
+	return ret;
+}
+
+static int bd96801_set_heartbeat_from_hw(struct wdtbd96801 *w,
+					 unsigned int conf_reg)
+{
+	int ret;
+	unsigned int val, sel, fast;
+
+	/*
+	 * The BD96801 supports a somewhat peculiar QA-mode, which we do not
+	 * support in this driver. If the QA-mode is enabled then we just
+	 * warn and bail-out.
+	 */
+	if ((conf_reg & BD96801_WD_EN_MASK) != BD96801_WD_IF_EN) {
+		dev_err(w->dev, "watchdog set to Q&A mode - exiting\n");
+		return -EINVAL;
+	}
+
+	ret = regmap_read(w->regmap, BD96801_REG_WD_TMO, &val);
+	if (ret)
+		return ret;
+
+	sel = FIELD_GET(BD96801_WD_TMO_SHORT_MASK, val);
+	fast = FASTNG_MIN << sel;
+
+	sel = (val & BD96801_WD_RATIO_MASK) + 1;
+	w->wdt.max_hw_heartbeat_ms = (fast << sel) / USEC_PER_MSEC;
+
+	if ((conf_reg & BD96801_WD_TYPE_MASK) == BD96801_WD_TYPE_WIN)
+		w->wdt.min_hw_heartbeat_ms = fast / USEC_PER_MSEC;
+
+	return 0;
+}
+
+static int init_wdg_hw(struct wdtbd96801 *w)
+{
+	u32 hw_margin[2];
+	int count, ret;
+	u32 hw_margin_max = BD96801_WDT_DEFAULT_MARGIN_MS, hw_margin_min = 0;
+
+	count = device_property_count_u32(w->dev->parent, "rohm,hw-timeout-ms");
+	if (count < 0 && count != -EINVAL)
+		return count;
+
+	if (count > 0) {
+		if (count > ARRAY_SIZE(hw_margin))
+			return -EINVAL;
+
+		ret = device_property_read_u32_array(w->dev->parent,
+						     "rohm,hw-timeout-ms",
+						     &hw_margin[0], count);
+		if (ret < 0)
+			return ret;
+
+		if (count == 1)
+			hw_margin_max = hw_margin[0];
+
+		if (count == 2) {
+			if (hw_margin[1] > hw_margin[0]) {
+				hw_margin_max = hw_margin[1];
+				hw_margin_min = hw_margin[0];
+			} else {
+				hw_margin_max = hw_margin[0];
+				hw_margin_min = hw_margin[1];
+			}
+		}
+	}
+
+	ret = bd96801_set_wdt_mode(w, hw_margin_max, hw_margin_min);
+	if (ret)
+		return ret;
+
+	ret = device_property_match_string(w->dev->parent, "rohm,wdg-action",
+					   "prstb");
+	if (ret >= 0) {
+		ret = regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
+				 BD96801_WD_ASSERT_MASK,
+				 BD96801_WD_ASSERT_RST);
+		return ret;
+	}
+
+	ret = device_property_match_string(w->dev->parent, "rohm,wdg-action",
+					   "intb-only");
+	if (ret >= 0) {
+		ret = regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
+				 BD96801_WD_ASSERT_MASK,
+				 BD96801_WD_ASSERT_IRQ);
+		return ret;
+	}
+
+	return 0;
+}
+
+static irqreturn_t bd96801_irq_hnd(int irq, void *data)
+{
+	emergency_restart();
+
+	return IRQ_NONE;
+}
+
+static int bd96801_wdt_probe(struct platform_device *pdev)
+{
+	struct wdtbd96801 *w;
+	int ret, irq;
+	unsigned int val;
+
+	w = devm_kzalloc(&pdev->dev, sizeof(*w), GFP_KERNEL);
+	if (!w)
+		return -ENOMEM;
+
+	w->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	w->dev = &pdev->dev;
+
+	w->wdt.info = &bd96801_wdt_info;
+	w->wdt.ops =  &bd96801_wdt_ops;
+	w->wdt.parent = pdev->dev.parent;
+	w->wdt.timeout = DEFAULT_TIMEOUT;
+	watchdog_set_drvdata(&w->wdt, w);
+
+	ret = regmap_read(w->regmap, BD96801_REG_WD_CONF, &val);
+	if (ret)
+		return dev_err_probe(&pdev->dev, ret,
+				     "Failed to get the watchdog state\n");
+
+	/*
+	 * If the WDG is already enabled we assume it is configured by boot.
+	 * In this case we just update the hw-timeout based on values set to
+	 * the timeout / mode registers and leave the hardware configs
+	 * untouched.
+	 */
+	if ((val & BD96801_WD_EN_MASK) != BD96801_WD_DISABLE) {
+		dev_dbg(&pdev->dev, "watchdog was running during probe\n");
+		ret = bd96801_set_heartbeat_from_hw(w, val);
+		if (ret)
+			return ret;
+
+		set_bit(WDOG_HW_RUNNING, &w->wdt.status);
+	} else {
+		/* If WDG is not running so we will initializate it */
+		ret = init_wdg_hw(w);
+		if (ret)
+			return ret;
+	}
+
+	dev_dbg(w->dev, "heartbeat set to %u - %u\n",
+		w->wdt.min_hw_heartbeat_ms, w->wdt.max_hw_heartbeat_ms);
+
+	watchdog_init_timeout(&w->wdt, 0, pdev->dev.parent);
+	watchdog_set_nowayout(&w->wdt, nowayout);
+	watchdog_stop_on_reboot(&w->wdt);
+
+	irq = platform_get_irq_byname(pdev, "bd96801-wdg");
+	if (irq > 0) {
+		ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+						bd96801_irq_hnd,
+						IRQF_ONESHOT,  "bd96801-wdg",
+						NULL);
+		if (ret)
+			return dev_err_probe(&pdev->dev, ret,
+					     "Failed to register IRQ\n");
+	}
+
+	return devm_watchdog_register_device(&pdev->dev, &w->wdt);
+}
+
+static const struct platform_device_id bd96801_wdt_id[] = {
+	{ "bd96801-wdt", },
+	{ }
+};
+MODULE_DEVICE_TABLE(platform, bd96801_wdt_id);
+
+static struct platform_driver bd96801_wdt = {
+	.driver = {
+		.name = "bd96801-wdt"
+	},
+	.probe = bd96801_wdt_probe,
+	.id_table = bd96801_wdt_id,
+};
+module_platform_driver(bd96801_wdt);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD96801 watchdog driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/rohm-bd96801.h b/include/linux/mfd/rohm-bd96801.h
new file mode 100644
index 000000000000..e2d9e10b6364
--- /dev/null
+++ b/include/linux/mfd/rohm-bd96801.h
@@ -0,0 +1,215 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* Copyright (C) 2024 ROHM Semiconductors */
+
+#ifndef __MFD_BD96801_H__
+#define __MFD_BD96801_H__
+
+#define BD96801_REG_SSCG_CTRL		0x09
+#define BD96801_REG_SHD_INTB            0x20
+#define BD96801_LDO5_VOL_LVL_REG	0x2c
+#define BD96801_LDO6_VOL_LVL_REG	0x2d
+#define BD96801_LDO7_VOL_LVL_REG	0x2e
+#define BD96801_REG_BUCK_OVP		0x30
+#define BD96801_REG_BUCK_OVD		0x35
+#define BD96801_REG_LDO_OVP		0x31
+#define BD96801_REG_LDO_OVD		0x36
+#define BD96801_REG_BOOT_OVERTIME	0x3a
+#define BD96801_REG_WD_TMO		0x40
+#define BD96801_REG_WD_CONF		0x41
+#define BD96801_REG_WD_FEED		0x42
+#define BD96801_REG_WD_FAILCOUNT	0x43
+#define BD96801_REG_WD_ASK		0x46
+#define BD96801_REG_WD_STATUS		0x4a
+#define BD96801_REG_PMIC_STATE		0x4f
+#define BD96801_REG_EXT_STATE		0x50
+
+#define BD96801_STATE_STBY		0x09
+
+#define BD96801_LOCK_REG		0x04
+#define BD96801_UNLOCK			0x9d
+#define BD96801_LOCK			0x00
+
+/* IRQ register area */
+#define BD96801_REG_INT_MAIN		0x51
+
+/*
+ * The BD96801 has two physical IRQ lines, INTB and ERRB.
+ *
+ * The 'main status register' is located at 0x51.
+ * The ERRB status registers are located at 0x52 ... 0x5B
+ * INTB status registers are at range 0x5c ... 0x63
+ */
+#define BD96801_REG_INT_SYS_ERRB1	0x52
+#define BD96801_REG_INT_SYS_INTB	0x5c
+#define BD96801_REG_INT_LDO7_INTB	0x63
+
+/* MASK registers */
+#define BD96801_REG_MASK_SYS_INTB	0x73
+#define BD96801_REG_MASK_SYS_ERRB	0x69
+
+#define BD96801_MAX_REGISTER		0x7a
+
+#define BD96801_OTP_ERR_MASK		BIT(0)
+#define BD96801_DBIST_ERR_MASK		BIT(1)
+#define BD96801_EEP_ERR_MASK		BIT(2)
+#define BD96801_ABIST_ERR_MASK		BIT(3)
+#define BD96801_PRSTB_ERR_MASK		BIT(4)
+#define BD96801_DRMOS1_ERR_MASK		BIT(5)
+#define BD96801_DRMOS2_ERR_MASK		BIT(6)
+#define BD96801_SLAVE_ERR_MASK		BIT(7)
+#define BD96801_VREF_ERR_MASK		BIT(0)
+#define BD96801_TSD_ERR_MASK		BIT(1)
+#define BD96801_UVLO_ERR_MASK		BIT(2)
+#define BD96801_OVLO_ERR_MASK		BIT(3)
+#define BD96801_OSC_ERR_MASK		BIT(4)
+#define BD96801_PON_ERR_MASK		BIT(5)
+#define BD96801_POFF_ERR_MASK		BIT(6)
+#define BD96801_CMD_SHDN_ERR_MASK	BIT(7)
+#define BD96801_INT_PRSTB_WDT_ERR_MASK	BIT(0)
+#define BD96801_INT_CHIP_IF_ERR_MASK	BIT(3)
+#define BD96801_INT_SHDN_ERR_MASK	BIT(7)
+#define BD96801_OUT_PVIN_ERR_MASK	BIT(0)
+#define BD96801_OUT_OVP_ERR_MASK	BIT(1)
+#define BD96801_OUT_UVP_ERR_MASK	BIT(2)
+#define BD96801_OUT_SHDN_ERR_MASK	BIT(7)
+
+/* ERRB IRQs */
+enum {
+	/* Reg 0x52, 0x53, 0x54 - ERRB system IRQs */
+	BD96801_OTP_ERR_STAT,
+	BD96801_DBIST_ERR_STAT,
+	BD96801_EEP_ERR_STAT,
+	BD96801_ABIST_ERR_STAT,
+	BD96801_PRSTB_ERR_STAT,
+	BD96801_DRMOS1_ERR_STAT,
+	BD96801_DRMOS2_ERR_STAT,
+	BD96801_SLAVE_ERR_STAT,
+	BD96801_VREF_ERR_STAT,
+	BD96801_TSD_ERR_STAT,
+	BD96801_UVLO_ERR_STAT,
+	BD96801_OVLO_ERR_STAT,
+	BD96801_OSC_ERR_STAT,
+	BD96801_PON_ERR_STAT,
+	BD96801_POFF_ERR_STAT,
+	BD96801_CMD_SHDN_ERR_STAT,
+	BD96801_INT_PRSTB_WDT_ERR,
+	BD96801_INT_CHIP_IF_ERR,
+	BD96801_INT_SHDN_ERR_STAT,
+
+	/* Reg 0x55 BUCK1 ERR IRQs */
+	BD96801_BUCK1_PVIN_ERR_STAT,
+	BD96801_BUCK1_OVP_ERR_STAT,
+	BD96801_BUCK1_UVP_ERR_STAT,
+	BD96801_BUCK1_SHDN_ERR_STAT,
+
+	/* Reg 0x56 BUCK2 ERR IRQs */
+	BD96801_BUCK2_PVIN_ERR_STAT,
+	BD96801_BUCK2_OVP_ERR_STAT,
+	BD96801_BUCK2_UVP_ERR_STAT,
+	BD96801_BUCK2_SHDN_ERR_STAT,
+
+	/* Reg 0x57 BUCK3 ERR IRQs */
+	BD96801_BUCK3_PVIN_ERR_STAT,
+	BD96801_BUCK3_OVP_ERR_STAT,
+	BD96801_BUCK3_UVP_ERR_STAT,
+	BD96801_BUCK3_SHDN_ERR_STAT,
+
+	/* Reg 0x58 BUCK4 ERR IRQs */
+	BD96801_BUCK4_PVIN_ERR_STAT,
+	BD96801_BUCK4_OVP_ERR_STAT,
+	BD96801_BUCK4_UVP_ERR_STAT,
+	BD96801_BUCK4_SHDN_ERR_STAT,
+
+	/* Reg 0x59 LDO5 ERR IRQs */
+	BD96801_LDO5_PVIN_ERR_STAT,
+	BD96801_LDO5_OVP_ERR_STAT,
+	BD96801_LDO5_UVP_ERR_STAT,
+	BD96801_LDO5_SHDN_ERR_STAT,
+
+	/* Reg 0x5a LDO6 ERR IRQs */
+	BD96801_LDO6_PVIN_ERR_STAT,
+	BD96801_LDO6_OVP_ERR_STAT,
+	BD96801_LDO6_UVP_ERR_STAT,
+	BD96801_LDO6_SHDN_ERR_STAT,
+
+	/* Reg 0x5b LDO7 ERR IRQs */
+	BD96801_LDO7_PVIN_ERR_STAT,
+	BD96801_LDO7_OVP_ERR_STAT,
+	BD96801_LDO7_UVP_ERR_STAT,
+	BD96801_LDO7_SHDN_ERR_STAT,
+};
+
+/* INTB IRQs */
+enum {
+	/* Reg 0x5c (System INTB) */
+	BD96801_TW_STAT,
+	BD96801_WDT_ERR_STAT,
+	BD96801_I2C_ERR_STAT,
+	BD96801_CHIP_IF_ERR_STAT,
+
+	/* Reg 0x5d (BUCK1 INTB) */
+	BD96801_BUCK1_OCPH_STAT,
+	BD96801_BUCK1_OCPL_STAT,
+	BD96801_BUCK1_OCPN_STAT,
+	BD96801_BUCK1_OVD_STAT,
+	BD96801_BUCK1_UVD_STAT,
+	BD96801_BUCK1_TW_CH_STAT,
+
+	/* Reg 0x5e (BUCK2 INTB) */
+	BD96801_BUCK2_OCPH_STAT,
+	BD96801_BUCK2_OCPL_STAT,
+	BD96801_BUCK2_OCPN_STAT,
+	BD96801_BUCK2_OVD_STAT,
+	BD96801_BUCK2_UVD_STAT,
+	BD96801_BUCK2_TW_CH_STAT,
+
+	/* Reg 0x5f (BUCK3 INTB)*/
+	BD96801_BUCK3_OCPH_STAT,
+	BD96801_BUCK3_OCPL_STAT,
+	BD96801_BUCK3_OCPN_STAT,
+	BD96801_BUCK3_OVD_STAT,
+	BD96801_BUCK3_UVD_STAT,
+	BD96801_BUCK3_TW_CH_STAT,
+
+	/* Reg 0x60 (BUCK4 INTB)*/
+	BD96801_BUCK4_OCPH_STAT,
+	BD96801_BUCK4_OCPL_STAT,
+	BD96801_BUCK4_OCPN_STAT,
+	BD96801_BUCK4_OVD_STAT,
+	BD96801_BUCK4_UVD_STAT,
+	BD96801_BUCK4_TW_CH_STAT,
+
+	/* Reg 0x61 (LDO5 INTB) */
+	BD96801_LDO5_OCPH_STAT, /* bit [0] */
+	BD96801_LDO5_OVD_STAT,	/* bit [3] */
+	BD96801_LDO5_UVD_STAT,  /* bit [4] */
+
+	/* Reg 0x62 (LDO6 INTB) */
+	BD96801_LDO6_OCPH_STAT, /* bit [0] */
+	BD96801_LDO6_OVD_STAT,	/* bit [3] */
+	BD96801_LDO6_UVD_STAT,  /* bit [4] */
+
+	/* Reg 0x63 (LDO7 INTB) */
+	BD96801_LDO7_OCPH_STAT, /* bit [0] */
+	BD96801_LDO7_OVD_STAT,	/* bit [3] */
+	BD96801_LDO7_UVD_STAT,  /* bit [4] */
+};
+
+/* IRQ MASKs */
+#define BD96801_TW_STAT_MASK		BIT(0)
+#define BD96801_WDT_ERR_STAT_MASK	BIT(1)
+#define BD96801_I2C_ERR_STAT_MASK	BIT(2)
+#define BD96801_CHIP_IF_ERR_STAT_MASK	BIT(3)
+
+#define BD96801_BUCK_OCPH_STAT_MASK	BIT(0)
+#define BD96801_BUCK_OCPL_STAT_MASK	BIT(1)
+#define BD96801_BUCK_OCPN_STAT_MASK	BIT(2)
+#define BD96801_BUCK_OVD_STAT_MASK	BIT(3)
+#define BD96801_BUCK_UVD_STAT_MASK	BIT(4)
+#define BD96801_BUCK_TW_CH_STAT_MASK	BIT(5)
+
+#define BD96801_LDO_OCPH_STAT_MASK	BIT(0)
+#define BD96801_LDO_OVD_STAT_MASK	BIT(3)
+#define BD96801_LDO_UVD_STAT_MASK	BIT(4)
+
+#endif
diff --git a/include/linux/mfd/rohm-generic.h b/include/linux/mfd/rohm-generic.h
index 4eeb22876bad..e7d4e6afe388 100644
--- a/include/linux/mfd/rohm-generic.h
+++ b/include/linux/mfd/rohm-generic.h
@@ -16,6 +16,7 @@ enum rohm_chip_type {
 	ROHM_CHIP_TYPE_BD71828,
 	ROHM_CHIP_TYPE_BD71837,
 	ROHM_CHIP_TYPE_BD71847,
+	ROHM_CHIP_TYPE_BD96801,
 	ROHM_CHIP_TYPE_AMOUNT
 };