Merge tag 'arm-soc/for-4.10/devicetree-arm64' of http://github.com/Broadcom/stblinux into next/dt64

Pull "Broadcom devicetree-arm64 changes for 4.10" from Florian Fainelli:

This pull request contains Broadcom ARM64 based SoC Device Tree changes for
4.10, please pull the following:

- Robin updates the Northstart 2 DTS to use the generic IOMMU binding

- Scott renames the Broadcom Northstar 2 binding document to use a standard name
  including the brcm vendor prefix

- Kamal adds the QSPI Device Tree node to the Northstar 2 SoC and updates the
  Northstar 2 SVK reference board DTS file with it enabled.

- Rob adds the Device Tree node for the Broadcom PDC (mailbox) hardware to the
  Northstar 2 SoC

- Jon enables the SDIO1 block and adds proper PCIe PHYs Device Tree nodes to the
  Northstar 2 SoC

- Ray adds required properties NAND controller properties to make NAND work on
  the Northstar 2 SVK board, this was submitted as a 4.9 fixes and is included
  here to resolve DTS file merges

- Andrea removes an incorrect power LED from the Raspberry Pi 3 DTS

- Andreas fixes the compatible string for the BCM2837 (Raspberry Pi 3)

- Eric defines standard pinctrl groups in the BCM2835 GPIO node

- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
  to use their appropriate pinctrl functions

- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet

- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block

- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
  Device Tree nodes he also uses the proper DTSI file to define the USB host mode
  for the USB Device Tree nodes

* tag 'arm-soc/for-4.10/devicetree-arm64' of http://github.com/Broadcom/stblinux: (23 commits)
  arm64: dts: NS2: Add PCI PHYs
  arm64: dts: NS2: enable sdio1
  ARM64: dts: bcm2837-rpi-3-b: remove incorrect pwr LED
  ARM64: bcm2835: dts: add thermal node to device-tree of bcm2837
  ARM: bcm2835: Add names for the Raspberry Pi GPIO lines
  ARM: bcm2835: dts: add thermal node to device-tree of bcm283x
  dt: bindings: add thermal device driver for bcm2835
  arm64: dts: Add Broadcom Northstar2 device tree entries for PDC driver.
  ARM: dts: bcm283x: fix typo in mailbox address
  DT: binding: bcm2835-mbox: fix address typo in example
  ARM64: dts: bcm2835: Fix bcm2837 compatible string
  arm64: dts: Update Broadcom NS2 to generic IOMMU binding
  arm64: dts: Updated NAND DT properties for NS2 SVK
  arm64: dts: rename ns2.txt to brcm,ns2.txt
  ARM64: dts: Add QSPI Device Tree node for NS2
  ARM64: dts: bcm283x: Use dtsi for USB host mode
  ARM: dts: bcm283x: drop alt3 from &gpio
  ARM: dts: bcm283x: add pinctrl group to &sdhci, drop pins from &gpio
  ARM: dts: bcm283x: add pinctrl group to &i2c1, drop pins from &gpio
  ARM: dts: bcm283x: add pinctrl group to &i2c0, drop pins from &gpio
  ...

21 files changed, 701 insertions, 30 deletions

diff --git a/Documentation/devicetree/bindings/arm/bcm/ns2.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,ns2.txt
index 35f056f4a1c3..35f056f4a1c3 100644
--- a/Documentation/devicetree/bindings/arm/bcm/ns2.txt
+++ b/Documentation/devicetree/bindings/arm/bcm/brcm,ns2.txt
diff --git a/Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt b/Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt
index e893615ef635..b48d7d30012c 100644
--- a/Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt
+++ b/Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt
@@ -12,7 +12,7 @@ Required properties:
 
 Example:
 
-mailbox: mailbox@7e00b800 {
+mailbox: mailbox@7e00b880 {
 	compatible = "brcm,bcm2835-mbox";
 	reg = <0x7e00b880 0x40>;
 	interrupts = <0 1>;
diff --git a/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt b/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt
new file mode 100644
index 000000000000..474531d2b2c5
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt
@@ -0,0 +1,17 @@
+Binding for Thermal Sensor driver for BCM2835 SoCs.
+
+Required parameters:
+-------------------
+
+compatible: 	should be one of: "brcm,bcm2835-thermal",
+		"brcm,bcm2836-thermal" or "brcm,bcm2837-thermal"
+reg:		Address range of the thermal registers.
+clocks: 	Phandle of the clock used by the thermal sensor.
+
+Example:
+
+thermal: thermal@7e212000 {
+	compatible = "brcm,bcm2835-thermal";
+	reg = <0x7e212000 0x8>;
+	clocks = <&clocks BCM2835_CLOCK_TSENS>;
+};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
index f7f9db355d98..5a22c7965f34 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
@@ -22,7 +22,72 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+	/*
+	 * This is based on the unreleased schematic for the Model A+.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "NC", /* GPIO30 */
+			  "NC", /* GPIO31 */
+			  "NC", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "PWR_LOW_N", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "PWM0_OUT", /* GPIO40 */
+			  "CAM_GPIO0", /* GPIO41 */
+			  "NC", /* GPIO42 */
+			  "NC", /* GPIO43 */
+			  "NC", /* GPIO44 */
+			  "PWM1_OUT", /* GPIO45 */
+			  "HDMI_HPD_N",
+			  "STATUS_LED",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
 	i2s_alt0: i2s_alt0 {
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a.dts b/arch/arm/boot/dts/bcm2835-rpi-a.dts
index 8be102f5d826..54f98c59a75d 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a.dts
@@ -15,7 +15,74 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
+	/*
+	 * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf
+	 * RPI00021 sheet 02
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "CAM_CLK",
+			  "LAN_RUN",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "NC", /* GPIO12 */
+			  "NC", /* GPIO13 */
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "STATUS_LED_N",
+			  "GPIO17",
+			  "GPIO18",
+			  "NC", /* GPIO19 */
+			  "NC", /* GPIO20 */
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "NC", /* GPIO26 */
+			  "CAM_GPIO",
+			  /* Binary number representing build/revision */
+			  "CONFIG0",
+			  "CONFIG1",
+			  "CONFIG2",
+			  "CONFIG3",
+			  "NC", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "NC", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "PWM0_OUT",
+			  "NC", /* GPIO41 */
+			  "NC", /* GPIO42 */
+			  "NC", /* GPIO43 */
+			  "NC", /* GPIO44 */
+			  "PWM1_OUT",
+			  "HDMI_HPD_P",
+			  "SD_CARD_DET",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
 
 	/* I2S interface */
 	i2s_alt2: i2s_alt2 {
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
index 35cde65c975e..b67587e6cbef 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
@@ -23,7 +23,73 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+	/*
+	 * Taken from Raspberry-Pi-B-Plus-V1.2-Schematics.pdf
+	 * RPI-BPLUS sheet 1
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "NC", /* GPIO30 */
+			  "LAN_RUN", /* GPIO31 */
+			  "CAM_GPIO1", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "PWR_LOW_N", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "PWM0_OUT", /* GPIO40 */
+			  "CAM_GPIO0", /* GPIO41 */
+			  "NC", /* GPIO42 */
+			  "NC", /* GPIO43 */
+			  "ETHCLK", /* GPIO44 */
+			  "PWM1_OUT", /* GPIO45 */
+			  "HDMI_HPD_N",
+			  "STATUS_LED",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
 	i2s_alt0: i2s_alt0 {
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
index 84df85ea6296..4133bc2cd9be 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
@@ -16,7 +16,73 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
+	/*
+	 * Taken from Raspberry-Pi-Rev-2.0-Model-AB-Schematics.pdf
+	 * RPI00022 sheet 02
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "CAM_CLK",
+			  "LAN_RUN",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "NC", /* GPIO12 */
+			  "NC", /* GPIO13 */
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "STATUS_LED_N",
+			  "GPIO17",
+			  "GPIO18",
+			  "NC", /* GPIO19 */
+			  "NC", /* GPIO20 */
+			  "CAM_GPIO",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "NC", /* GPIO26 */
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "NC", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "NC", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "PWM0_OUT",
+			  "NC", /* GPIO41 */
+			  "NC", /* GPIO42 */
+			  "NC", /* GPIO43 */
+			  "NC", /* GPIO44 */
+			  "PWM1_OUT",
+			  "HDMI_HPD_P",
+			  "SD_CARD_DET",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
 
 	/* I2S interface */
 	i2s_alt2: i2s_alt2 {
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b.dts b/arch/arm/boot/dts/bcm2835-rpi-b.dts
index 8e626a80fe24..71f50e16c646 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts
@@ -16,7 +16,74 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &alt3>;
+	/*
+	 * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf
+	 * RPI00021 sheet 02
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "CAM_CLK",
+			  "LAN_RUN",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "NC", /* GPIO12 */
+			  "NC", /* GPIO13 */
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "STATUS_LED_N",
+			  "GPIO17",
+			  "GPIO18",
+			  "NC", /* GPIO19 */
+			  "NC", /* GPIO20 */
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "NC", /* GPIO26 */
+			  "CAM_GPIO",
+			  /* Binary number representing build/revision */
+			  "CONFIG0",
+			  "CONFIG1",
+			  "CONFIG2",
+			  "CONFIG3",
+			  "NC", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "NC", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "PWM0_OUT",
+			  "NC", /* GPIO41 */
+			  "NC", /* GPIO42 */
+			  "NC", /* GPIO43 */
+			  "NC", /* GPIO44 */
+			  "PWM1_OUT",
+			  "HDMI_HPD_P",
+			  "SD_CARD_DET",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0>;
 };
 
 &hdmi {
diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero.dts b/arch/arm/boot/dts/bcm2835-rpi-zero.dts
index 60e359fafc5b..7c1c18048948 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-zero.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-zero.dts
@@ -26,7 +26,7 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
 	i2s_alt0: i2s_alt0 {
diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index e9b47b2bbc33..6ddf7dfe3f72 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -39,22 +39,21 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 14 15 40 45>;
+		brcm,pins = <4 5 7 8 9 10 11 14 15>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
-
-	alt3: alt3 {
-		brcm,pins = <48 49 50 51 52 53>;
-		brcm,function = <BCM2835_FSEL_ALT3>;
-	};
 };
 
 &i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_gpio0>;
 	status = "okay";
 	clock-frequency = <100000>;
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_gpio2>;
 	status = "okay";
 	clock-frequency = <100000>;
 };
@@ -64,11 +63,15 @@
 };
 
 &sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio48>;
 	status = "okay";
 	bus-width = <4>;
 };
 
 &pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi
index a78759e73710..0890d97e674d 100644
--- a/arch/arm/boot/dts/bcm2835.dtsi
+++ b/arch/arm/boot/dts/bcm2835.dtsi
@@ -23,3 +23,9 @@
 		};
 	};
 };
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+	compatible = "brcm,bcm2835-thermal";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
index 39dccf62ac96..bf19e8cfb9e6 100644
--- a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
@@ -27,7 +27,7 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
 	i2s_alt0: i2s_alt0 {
diff --git a/arch/arm/boot/dts/bcm2836.dtsi b/arch/arm/boot/dts/bcm2836.dtsi
index 9d0651d8f373..519a44f5d25a 100644
--- a/arch/arm/boot/dts/bcm2836.dtsi
+++ b/arch/arm/boot/dts/bcm2836.dtsi
@@ -76,3 +76,9 @@
 	interrupt-parent = <&local_intc>;
 	interrupts = <8>;
 };
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+	compatible = "brcm,bcm2836-thermal";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 46d46d894a44..9a44da190897 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -104,7 +104,7 @@
 			reg = <0x7e104000 0x10>;
 		};
 
-		mailbox: mailbox@7e00b800 {
+		mailbox: mailbox@7e00b880 {
 			compatible = "brcm,bcm2835-mbox";
 			reg = <0x7e00b880 0x40>;
 			interrupts = <0 1>;
@@ -132,6 +132,209 @@
 
 			interrupt-controller;
 			#interrupt-cells = <2>;
+
+			/* Defines pin muxing groups according to
+			 * BCM2835-ARM-Peripherals.pdf page 102.
+			 *
+			 * While each pin can have its mux selected
+			 * for various functions individually, some
+			 * groups only make sense to switch to a
+			 * particular function together.
+			 */
+			dpi_gpio0: dpi_gpio0 {
+				brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
+					     12 13 14 15 16 17 18 19
+					     20 21 22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			emmc_gpio22: emmc_gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			emmc_gpio34: emmc_gpio34 {
+				brcm,pins = <34 35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+				brcm,pull = <BCM2835_PUD_OFF
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP>;
+			};
+			emmc_gpio48: emmc_gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+
+			gpclk0_gpio4: gpclk0_gpio4 {
+				brcm,pins = <4>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio5: gpclk1_gpio5 {
+				brcm,pins = <5>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio42: gpclk1_gpio42 {
+				brcm,pins = <42>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio44: gpclk1_gpio44 {
+				brcm,pins = <44>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio6: gpclk2_gpio6 {
+				brcm,pins = <6>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio43: gpclk2_gpio43 {
+				brcm,pins = <43>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+
+			i2c0_gpio0: i2c0_gpio0 {
+				brcm,pins = <0 1>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio32: i2c0_gpio32 {
+				brcm,pins = <32 34>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio44: i2c0_gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT1>;
+			};
+			i2c1_gpio2: i2c1_gpio2 {
+				brcm,pins = <2 3>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c1_gpio44: i2c1_gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			i2c_slave_gpio18: i2c_slave_gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+
+			jtag_gpio4: jtag_gpio4 {
+				brcm,pins = <4 5 6 12 13>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			jtag_gpio22: jtag_gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+
+			pcm_gpio18: pcm_gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pcm_gpio28: pcm_gpio28 {
+				brcm,pins = <28 29 30 31>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+
+			pwm0_gpio12: pwm0_gpio12 {
+				brcm,pins = <12>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm0_gpio18: pwm0_gpio18 {
+				brcm,pins = <18>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			pwm0_gpio40: pwm0_gpio40 {
+				brcm,pins = <40>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio13: pwm1_gpio13 {
+				brcm,pins = <13>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio19: pwm1_gpio19 {
+				brcm,pins = <19>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			pwm1_gpio41: pwm1_gpio41 {
+				brcm,pins = <41>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio45: pwm1_gpio45 {
+				brcm,pins = <45>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+
+			sdhost_gpio48: sdhost_gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+
+			spi0_gpio7: spi0_gpio7 {
+				brcm,pins = <7 8 9 10 11>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spi0_gpio35: spi0_gpio35 {
+				brcm,pins = <35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spi1_gpio16: spi1_gpio16 {
+				brcm,pins = <16 17 18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			spi2_gpio40: spi2_gpio40 {
+				brcm,pins = <40 41 42 43 44 45>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+
+			uart0_gpio14: uart0_gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			/* Separate from the uart0_gpio14 group
+			 * because it conflicts with spi1_gpio16, and
+			 * people often run uart0 on the two pins
+			 * without flow contrl.
+			 */
+			uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_gpio30: uart0_gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_ctsrts_gpio32: uart0_ctsrts_gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+
+			uart1_gpio14: uart1_gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio32: uart1_gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio36: uart1_gpio36 {
+				brcm,pins = <36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			uart1_gpio40: uart1_gpio40 {
+				brcm,pins = <40 41>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
+				brcm,pins = <42 43>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
 		};
 
 		uart0: serial@7e201000 {
@@ -187,6 +390,13 @@
 			interrupts = <2 14>; /* pwa1 */
 		};
 
+		thermal: thermal@7e212000 {
+			compatible = "brcm,bcm2835-thermal";
+			reg = <0x7e212000 0x8>;
+			clocks = <&clocks BCM2835_CLOCK_TSENS>;
+			status = "disabled";
+		};
+
 		aux: aux@0x7e215000 {
 			compatible = "brcm,bcm2835-aux";
 			#clock-cells = <1>;
diff --git a/arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dts b/arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dts
index 7841b724e340..c309633a1e87 100644
--- a/arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dts
+++ b/arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dts
@@ -2,6 +2,7 @@
 #include "bcm2837.dtsi"
 #include "bcm2835-rpi.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
 
 / {
 	compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
@@ -15,13 +16,6 @@
 		act {
 			gpios = <&gpio 47 0>;
 		};
-
-		pwr {
-			label = "PWR";
-			gpios = <&gpio 35 0>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
 	};
 };
 
diff --git a/arch/arm64/boot/dts/broadcom/bcm2837.dtsi b/arch/arm64/boot/dts/broadcom/bcm2837.dtsi
index 8216bbb29fe0..19f2fe620a21 100644
--- a/arch/arm64/boot/dts/broadcom/bcm2837.dtsi
+++ b/arch/arm64/boot/dts/broadcom/bcm2837.dtsi
@@ -1,7 +1,7 @@
 #include "bcm283x.dtsi"
 
 / {
-	compatible = "brcm,bcm2836";
+	compatible = "brcm,bcm2837";
 
 	soc {
 		ranges = <0x7e000000 0x3f000000 0x1000000>,
@@ -74,3 +74,9 @@
 	interrupt-parent = <&local_intc>;
 	interrupts = <8>;
 };
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+	compatible = "brcm,bcm2837-thermal";
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcm283x-rpi-usb-host.dtsi b/arch/arm64/boot/dts/broadcom/bcm283x-rpi-usb-host.dtsi
new file mode 120000
index 000000000000..cbeebe312ff8
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcm283x-rpi-usb-host.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/bcm283x-rpi-usb-host.dtsi
\ No newline at end of file
diff --git a/arch/arm64/boot/dts/broadcom/ns2-svk.dts b/arch/arm64/boot/dts/broadcom/ns2-svk.dts
index b09f3bc5c6c1..34619079a6c6 100644
--- a/arch/arm64/boot/dts/broadcom/ns2-svk.dts
+++ b/arch/arm64/boot/dts/broadcom/ns2-svk.dts
@@ -157,6 +157,10 @@
 	status = "ok";
 };
 
+&sdio1 {
+	status = "ok";
+};
+
 &nand {
 	nandcs@0 {
 		compatible = "brcm,nandcs";
@@ -187,3 +191,37 @@
 		groups = "nand_grp";
 	};
 };
+
+&qspi {
+	bspi-sel = <0>;
+	flash: m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		reg = <0x0>;
+		spi-max-frequency = <12500000>;
+		m25p,fast-read;
+		spi-cpol;
+		spi-cpha;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x000a0000>;
+		};
+
+		partition@a0000 {
+			label = "env";
+			reg = <0x000a0000 0x00060000>;
+		};
+
+		partition@100000 {
+			label = "system";
+			reg = <0x00100000 0x00600000>;
+		};
+
+		partition@700000 {
+			label = "rootfs";
+			reg = <0x00700000 0x01900000>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/broadcom/ns2.dtsi b/arch/arm64/boot/dts/broadcom/ns2.dtsi
index d95dc408629a..863503d78f57 100644
--- a/arch/arm64/boot/dts/broadcom/ns2.dtsi
+++ b/arch/arm64/boot/dts/broadcom/ns2.dtsi
@@ -133,6 +133,9 @@
 
 		status = "disabled";
 
+		phys = <&pci_phy0>;
+		phy-names = "pcie-phy";
+
 		msi-parent = <&msi0>;
 		msi0: msi@20020000 {
 			compatible = "brcm,iproc-msi";
@@ -171,6 +174,9 @@
 
 		status = "disabled";
 
+		phys = <&pci_phy1>;
+		phy-names = "pcie-phy";
+
 		msi-parent = <&msi4>;
 		msi4: msi@50020000 {
 			compatible = "brcm,iproc-msi";
@@ -191,6 +197,42 @@
 
 		#include "ns2-clock.dtsi"
 
+		pdc0: iproc-pdc0@612c0000 {
+			compatible = "brcm,iproc-pdc-mbox";
+			reg = <0x612c0000 0x445>;  /* PDC FS0 regs */
+			interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <1>;
+			brcm,rx-status-len = <32>;
+			brcm,use-bcm-hdr;
+		};
+
+		pdc1: iproc-pdc1@612e0000 {
+			compatible = "brcm,iproc-pdc-mbox";
+			reg = <0x612e0000 0x445>;  /* PDC FS1 regs */
+			interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <1>;
+			brcm,rx-status-len = <32>;
+			brcm,use-bcm-hdr;
+		};
+
+		pdc2: iproc-pdc2@61300000 {
+			compatible = "brcm,iproc-pdc-mbox";
+			reg = <0x61300000 0x445>;  /* PDC FS2 regs */
+			interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <1>;
+			brcm,rx-status-len = <32>;
+			brcm,use-bcm-hdr;
+		};
+
+		pdc3: iproc-pdc3@61320000 {
+			compatible = "brcm,iproc-pdc-mbox";
+			reg = <0x61320000 0x445>;  /* PDC FS3 regs */
+			interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <1>;
+			brcm,rx-status-len = <32>;
+			brcm,use-bcm-hdr;
+		};
+
 		dma0: dma@61360000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x61360000 0x1000>;
@@ -248,7 +290,7 @@
 				     <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>;
-			mmu-masters;
+			#iommu-cells = <1>;
 		};
 
 		pinctrl: pinctrl@6501d130 {
@@ -565,5 +607,23 @@
 
 			brcm,nand-has-wp;
 		};
+
+		qspi: spi@66470200 {
+			compatible = "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi";
+			reg = <0x66470200 0x184>,
+				<0x66470000 0x124>,
+				<0x67017408 0x004>,
+				<0x664703a0 0x01c>;
+			reg-names = "mspi", "bspi", "intr_regs",
+				"intr_status_reg";
+			interrupts = <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "spi_l1_intr";
+			clocks = <&iprocmed>;
+			clock-names = "iprocmed";
+			num-cs = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 	};
 };
diff --git a/drivers/pinctrl/bcm/pinctrl-bcm2835.c b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
index fa77165fab2c..4cf612bcfdfa 100644
--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
@@ -76,12 +76,6 @@ enum bcm2835_pinconf_param {
 	BCM2835_PINCONF_PARAM_PULL,
 };
 
-enum bcm2835_pinconf_pull {
-	BCM2835_PINCONFIG_PULL_NONE,
-	BCM2835_PINCONFIG_PULL_DOWN,
-	BCM2835_PINCONFIG_PULL_UP,
-};
-
 #define BCM2835_PINCONF_PACK(_param_, _arg_) ((_param_) << 16 | (_arg_))
 #define BCM2835_PINCONF_UNPACK_PARAM(_conf_) ((_conf_) >> 16)
 #define BCM2835_PINCONF_UNPACK_ARG(_conf_) ((_conf_) & 0xffff)
diff --git a/include/dt-bindings/pinctrl/bcm2835.h b/include/dt-bindings/pinctrl/bcm2835.h
index 6f0bc37af39c..e4e4fdf5d38f 100644
--- a/include/dt-bindings/pinctrl/bcm2835.h
+++ b/include/dt-bindings/pinctrl/bcm2835.h
@@ -24,4 +24,9 @@
 #define BCM2835_FSEL_ALT2	6
 #define BCM2835_FSEL_ALT3	7
 
+/* brcm,pull property */
+#define BCM2835_PUD_OFF		0
+#define BCM2835_PUD_DOWN	1
+#define BCM2835_PUD_UP		2
+
 #endif /* __DT_BINDINGS_PINCTRL_BCM2835_H__ */