dt-bindings: consolidate various misc bindings

Move various bindings in misc to appropriate subsystem directories.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>

3 files changed, 0 insertions, 163 deletions

diff --git a/Documentation/devicetree/bindings/misc/bmp085.txt b/Documentation/devicetree/bindings/misc/bmp085.txt
deleted file mode 100644
index d7a6deb6b21e..000000000000
--- a/Documentation/devicetree/bindings/misc/bmp085.txt
+++ /dev/null
@@ -1,24 +0,0 @@
-BMP085/BMP18x digital pressure sensors
-
-Required properties:
-- compatible: bosch,bmp085
-
-Optional properties:
-- chip-id: configurable chip id for non-default chip revisions
-- temp-measurement-period: temperature measurement period (milliseconds)
-- default-oversampling: default oversampling value to be used at startup,
-  value range is 0-3 with rising sensitivity.
-- interrupt-parent: should be the phandle for the interrupt controller
-- interrupts: interrupt mapping for IRQ
-
-Example:
-
-pressure@77 {
-	compatible = "bosch,bmp085";
-	reg = <0x77>;
-	chip-id = <10>;
-	temp-measurement-period = <100>;
-	default-oversampling = <2>;
-	interrupt-parent = <&gpio0>;
-	interrupts = <25 IRQ_TYPE_EDGE_RISING>;
-};
diff --git a/Documentation/devicetree/bindings/misc/lis302.txt b/Documentation/devicetree/bindings/misc/lis302.txt
deleted file mode 100644
index 2a19bff9693f..000000000000
--- a/Documentation/devicetree/bindings/misc/lis302.txt
+++ /dev/null
@@ -1,119 +0,0 @@
-LIS302 accelerometer devicetree bindings
-
-This device is matched via its bus drivers, and has a number of properties
-that apply in on the generic device (independent from the bus).
-
-
-Required properties for the SPI bindings:
- - compatible: 		should be set to "st,lis3lv02d_spi"
- - reg:			the chipselect index
- - spi-max-frequency:	maximal bus speed, should be set to 1000000 unless
-			constrained by external circuitry
- - interrupts:		the interrupt generated by the device
-
-Required properties for the I2C bindings:
- - compatible:		should be set to "st,lis3lv02d"
- - reg:			i2c slave address
- - Vdd-supply:		The input supply for Vdd
- - Vdd_IO-supply:	The input supply for Vdd_IO
-
-
-Optional properties for all bus drivers:
-
- - st,click-single-{x,y,z}:	if present, tells the device to issue an
-				interrupt on single click events on the
-				x/y/z axis.
- - st,click-double-{x,y,z}:	if present, tells the device to issue an
-				interrupt on double click events on the
-				x/y/z axis.
- - st,click-thresh-{x,y,z}:	set the x/y/z axis threshold
- - st,click-click-time-limit:	click time limit, from 0 to 127.5msec
-				with step of 0.5 msec
- - st,click-latency:		click latency, from 0 to 255 msec with
-				step of 1 msec.
- - st,click-window:		click window, from 0 to 255 msec with
-				step of 1 msec.
- - st,irq{1,2}-disable:		disable IRQ 1/2
- - st,irq{1,2}-ff-wu-1:		raise IRQ 1/2 on FF_WU_1 condition
- - st,irq{1,2}-ff-wu-2:		raise IRQ 1/2 on FF_WU_2 condition
- - st,irq{1,2}-data-ready:	raise IRQ 1/2 on data ready contition
- - st,irq{1,2}-click:		raise IRQ 1/2 on click condition
- - st,irq-open-drain:		consider IRQ lines open-drain
- - st,irq-active-low:		make IRQ lines active low
- - st,wu-duration-1:		duration register for Free-Fall/Wake-Up
-				interrupt 1
- - st,wu-duration-2:		duration register for Free-Fall/Wake-Up
-				interrupt 2
- - st,wakeup-{x,y,z}-{lo,hi}:	set wakeup condition on x/y/z axis for
-				upper/lower limit
- - st,wakeup-threshold:		set wakeup threshold
- - st,wakeup2-{x,y,z}-{lo,hi}:	set wakeup condition on x/y/z axis for
-				upper/lower limit for second wakeup
-				engine.
- - st,wakeup2-threshold:	set wakeup threshold for second wakeup
-				engine.
- - st,highpass-cutoff-hz=:	1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of
-				highpass cut-off frequency
- - st,hipass{1,2}-disable:	disable highpass 1/2.
- - st,default-rate=:		set the default rate
- - st,axis-{x,y,z}=:		set the axis to map to the three coordinates.
-				Negative values can be used for inverted axis.
- - st,{min,max}-limit-{x,y,z}	set the min/max limits for x/y/z axis
-				(used by self-test)
-
-
-Example for a SPI device node:
-
-	lis302@0 {
-		compatible = "st,lis302dl-spi";
-		reg = <0>;
-		spi-max-frequency = <1000000>;
-		interrupt-parent = <&gpio>;
-		interrupts = <104 0>;
-
-		st,click-single-x;
-		st,click-single-y;
-		st,click-single-z;
-		st,click-thresh-x = <10>;
-		st,click-thresh-y = <10>;
-		st,click-thresh-z = <10>;
-		st,irq1-click;
-		st,irq2-click;
-		st,wakeup-x-lo;
-		st,wakeup-x-hi;
-		st,wakeup-y-lo;
-		st,wakeup-y-hi;
-		st,wakeup-z-lo;
-		st,wakeup-z-hi;
-	};
-
-Example for a I2C device node:
-
-	lis331dlh: lis331dlh@18 {
-		compatible = "st,lis331dlh", "st,lis3lv02d";
-		reg = <0x18>;
-		Vdd-supply = <&lis3_reg>;
-		Vdd_IO-supply = <&lis3_reg>;
-
-		st,click-single-x;
-		st,click-single-y;
-		st,click-single-z;
-		st,click-thresh-x = <10>;
-		st,click-thresh-y = <10>;
-		st,click-thresh-z = <10>;
-		st,irq1-click;
-		st,irq2-click;
-		st,wakeup-x-lo;
-		st,wakeup-x-hi;
-		st,wakeup-y-lo;
-		st,wakeup-y-hi;
-		st,wakeup-z-lo;
-		st,wakeup-z-hi;
-		st,min-limit-x = <120>;
-		st,min-limit-y = <120>;
-		st,min-limit-z = <140>;
-		st,max-limit-x = <550>;
-		st,max-limit-y = <550>;
-		st,max-limit-z = <750>;
-	};
-
diff --git a/Documentation/devicetree/bindings/misc/ti,dac7512.txt b/Documentation/devicetree/bindings/misc/ti,dac7512.txt
deleted file mode 100644
index 1db45939dac9..000000000000
--- a/Documentation/devicetree/bindings/misc/ti,dac7512.txt
+++ /dev/null
@@ -1,20 +0,0 @@
-TI DAC7512 DEVICETREE BINDINGS
-
-Required properties:
-
-	- "compatible"		Must be set to "ti,dac7512"
-
-Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt
-apply. In particular, "reg" and "spi-max-frequency" properties must be given.
-
-
-Example:
-
-	spi_master {
-		dac7512: dac7512@0 {
-			compatible = "ti,dac7512";
-			reg = <0>; /* CS0 */
-			spi-max-frequency = <1000000>;
-		};
-	};
-