diff options
| -rw-r--r-- | Documentation/devicetree/bindings/leds/common.yaml | 12 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/leds/leds-bcm63138.yaml | 4 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/leds/leds-bcm6328.yaml | 4 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/leds/leds-bcm6358.txt | 2 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/leds/leds-pwm-multicolor.yaml | 4 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/leds/leds-pwm.yaml | 5 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/net/qca,qca808x.yaml | 54 | ||||
| -rw-r--r-- | drivers/net/phy/at803x.c | 327 | ||||
| -rw-r--r-- | drivers/net/phy/phy_device.c | 16 | ||||
| -rw-r--r-- | include/linux/phy.h | 22 |
10 files changed, 431 insertions, 19 deletions
diff --git a/Documentation/devicetree/bindings/leds/common.yaml b/Documentation/devicetree/bindings/leds/common.yaml index 55a8d1385e21..8a3c2398b10c 100644 --- a/Documentation/devicetree/bindings/leds/common.yaml +++ b/Documentation/devicetree/bindings/leds/common.yaml @@ -200,6 +200,18 @@ properties: #trigger-source-cells property in the source node. $ref: /schemas/types.yaml#/definitions/phandle-array + active-low: + type: boolean + description: + Makes LED active low. To turn the LED ON, line needs to be + set to low voltage instead of high. + + inactive-high-impedance: + type: boolean + description: + Set LED to high-impedance mode to turn the LED OFF. LED might also + describe this mode as tristate. + # Required properties for flash LED child nodes: flash-max-microamp: description: diff --git a/Documentation/devicetree/bindings/leds/leds-bcm63138.yaml b/Documentation/devicetree/bindings/leds/leds-bcm63138.yaml index 52252fb6bb32..bb20394fca5c 100644 --- a/Documentation/devicetree/bindings/leds/leds-bcm63138.yaml +++ b/Documentation/devicetree/bindings/leds/leds-bcm63138.yaml @@ -52,10 +52,6 @@ patternProperties: maxItems: 1 description: LED pin number - active-low: - type: boolean - description: Makes LED active low - required: - reg diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6328.yaml b/Documentation/devicetree/bindings/leds/leds-bcm6328.yaml index 51cc0d82c12e..f3a3ef992929 100644 --- a/Documentation/devicetree/bindings/leds/leds-bcm6328.yaml +++ b/Documentation/devicetree/bindings/leds/leds-bcm6328.yaml @@ -78,10 +78,6 @@ patternProperties: - maximum: 23 description: LED pin number (only LEDs 0 to 23 are valid). - active-low: - type: boolean - description: Makes LED active low. - brcm,hardware-controlled: type: boolean description: Makes this LED hardware controlled. diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6358.txt b/Documentation/devicetree/bindings/leds/leds-bcm6358.txt index 6e51c6b91ee5..211ffc3c4a20 100644 --- a/Documentation/devicetree/bindings/leds/leds-bcm6358.txt +++ b/Documentation/devicetree/bindings/leds/leds-bcm6358.txt @@ -25,8 +25,6 @@ LED sub-node required properties: LED sub-node optional properties: - label : see Documentation/devicetree/bindings/leds/common.txt - - active-low : Boolean, makes LED active low. - Default : false - default-state : see Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : see diff --git a/Documentation/devicetree/bindings/leds/leds-pwm-multicolor.yaml b/Documentation/devicetree/bindings/leds/leds-pwm-multicolor.yaml index bd6ec04a8727..5edfbe347341 100644 --- a/Documentation/devicetree/bindings/leds/leds-pwm-multicolor.yaml +++ b/Documentation/devicetree/bindings/leds/leds-pwm-multicolor.yaml @@ -41,10 +41,6 @@ properties: pwm-names: true - active-low: - description: For PWMs where the LED is wired to supply rather than ground. - type: boolean - color: true required: diff --git a/Documentation/devicetree/bindings/leds/leds-pwm.yaml b/Documentation/devicetree/bindings/leds/leds-pwm.yaml index 7de6da58be3c..113b7c218303 100644 --- a/Documentation/devicetree/bindings/leds/leds-pwm.yaml +++ b/Documentation/devicetree/bindings/leds/leds-pwm.yaml @@ -34,11 +34,6 @@ patternProperties: Maximum brightness possible for the LED $ref: /schemas/types.yaml#/definitions/uint32 - active-low: - description: - For PWMs where the LED is wired to supply rather than ground. - type: boolean - required: - pwms - max-brightness diff --git a/Documentation/devicetree/bindings/net/qca,qca808x.yaml b/Documentation/devicetree/bindings/net/qca,qca808x.yaml new file mode 100644 index 000000000000..e2552655902a --- /dev/null +++ b/Documentation/devicetree/bindings/net/qca,qca808x.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qca,qca808x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Atheros QCA808X PHY + +maintainers: + - Christian Marangi <ansuelsmth@gmail.com> + +description: + QCA808X PHYs can have up to 3 LEDs attached. + All 3 LEDs are disabled by default. + 2 LEDs have dedicated pins with the 3rd LED having the + double function of Interrupt LEDs/GPIO or additional LED. + + By default this special PIN is set to LED function. + +allOf: + - $ref: ethernet-phy.yaml# + +properties: + compatible: + enum: + - ethernet-phy-id004d.d101 + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/leds/common.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-phy@0 { + compatible = "ethernet-phy-id004d.d101"; + reg = <0>; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_WAN; + default-state = "keep"; + }; + }; + }; + }; diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c index a62442a55774..9c07a6cc6e67 100644 --- a/drivers/net/phy/at803x.c +++ b/drivers/net/phy/at803x.c @@ -301,6 +301,87 @@ /* Added for reference of existence but should be handled by wait_for_completion already */ #define QCA808X_CDT_STATUS_STAT_BUSY (BIT(1) | BIT(3)) +#define QCA808X_MMD7_LED_GLOBAL 0x8073 +#define QCA808X_LED_BLINK_1 GENMASK(11, 6) +#define QCA808X_LED_BLINK_2 GENMASK(5, 0) +/* Values are the same for both BLINK_1 and BLINK_2 */ +#define QCA808X_LED_BLINK_FREQ_MASK GENMASK(5, 3) +#define QCA808X_LED_BLINK_FREQ_2HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x0) +#define QCA808X_LED_BLINK_FREQ_4HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x1) +#define QCA808X_LED_BLINK_FREQ_8HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x2) +#define QCA808X_LED_BLINK_FREQ_16HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x3) +#define QCA808X_LED_BLINK_FREQ_32HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x4) +#define QCA808X_LED_BLINK_FREQ_64HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x5) +#define QCA808X_LED_BLINK_FREQ_128HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x6) +#define QCA808X_LED_BLINK_FREQ_256HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x7) +#define QCA808X_LED_BLINK_DUTY_MASK GENMASK(2, 0) +#define QCA808X_LED_BLINK_DUTY_50_50 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x0) +#define QCA808X_LED_BLINK_DUTY_75_25 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x1) +#define QCA808X_LED_BLINK_DUTY_25_75 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x2) +#define QCA808X_LED_BLINK_DUTY_33_67 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x3) +#define QCA808X_LED_BLINK_DUTY_67_33 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x4) +#define QCA808X_LED_BLINK_DUTY_17_83 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x5) +#define QCA808X_LED_BLINK_DUTY_83_17 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x6) +#define QCA808X_LED_BLINK_DUTY_8_92 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x7) + +#define QCA808X_MMD7_LED2_CTRL 0x8074 +#define QCA808X_MMD7_LED2_FORCE_CTRL 0x8075 +#define QCA808X_MMD7_LED1_CTRL 0x8076 +#define QCA808X_MMD7_LED1_FORCE_CTRL 0x8077 +#define QCA808X_MMD7_LED0_CTRL 0x8078 +#define QCA808X_MMD7_LED_CTRL(x) (0x8078 - ((x) * 2)) + +/* LED hw control pattern is the same for every LED */ +#define QCA808X_LED_PATTERN_MASK GENMASK(15, 0) +#define QCA808X_LED_SPEED2500_ON BIT(15) +#define QCA808X_LED_SPEED2500_BLINK BIT(14) +/* Follow blink trigger even if duplex or speed condition doesn't match */ +#define QCA808X_LED_BLINK_CHECK_BYPASS BIT(13) +#define QCA808X_LED_FULL_DUPLEX_ON BIT(12) +#define QCA808X_LED_HALF_DUPLEX_ON BIT(11) +#define QCA808X_LED_TX_BLINK BIT(10) +#define QCA808X_LED_RX_BLINK BIT(9) +#define QCA808X_LED_TX_ON_10MS BIT(8) +#define QCA808X_LED_RX_ON_10MS BIT(7) +#define QCA808X_LED_SPEED1000_ON BIT(6) +#define QCA808X_LED_SPEED100_ON BIT(5) +#define QCA808X_LED_SPEED10_ON BIT(4) +#define QCA808X_LED_COLLISION_BLINK BIT(3) +#define QCA808X_LED_SPEED1000_BLINK BIT(2) +#define QCA808X_LED_SPEED100_BLINK BIT(1) +#define QCA808X_LED_SPEED10_BLINK BIT(0) + +#define QCA808X_MMD7_LED0_FORCE_CTRL 0x8079 +#define QCA808X_MMD7_LED_FORCE_CTRL(x) (0x8079 - ((x) * 2)) + +/* LED force ctrl is the same for every LED + * No documentation exist for this, not even internal one + * with NDA as QCOM gives only info about configuring + * hw control pattern rules and doesn't indicate any way + * to force the LED to specific mode. + * These define comes from reverse and testing and maybe + * lack of some info or some info are not entirely correct. + * For the basic LED control and hw control these finding + * are enough to support LED control in all the required APIs. + * + * On doing some comparison with implementation with qca807x, + * it was found that it's 1:1 equal to it and confirms all the + * reverse done. It was also found further specification with the + * force mode and the blink modes. + */ +#define QCA808X_LED_FORCE_EN BIT(15) +#define QCA808X_LED_FORCE_MODE_MASK GENMASK(14, 13) +#define QCA808X_LED_FORCE_BLINK_1 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x3) +#define QCA808X_LED_FORCE_BLINK_2 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x2) +#define QCA808X_LED_FORCE_ON FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x1) +#define QCA808X_LED_FORCE_OFF FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x0) + +#define QCA808X_MMD7_LED_POLARITY_CTRL 0x901a +/* QSDK sets by default 0x46 to this reg that sets BIT 6 for + * LED to active high. It's not clear what BIT 3 and BIT 4 does. + */ +#define QCA808X_LED_ACTIVE_HIGH BIT(6) + /* QCA808X 1G chip type */ #define QCA808X_PHY_MMD7_CHIP_TYPE 0x901d #define QCA808X_PHY_CHIP_TYPE_1G BIT(0) @@ -346,6 +427,7 @@ struct at803x_priv { struct regulator_dev *vddio_rdev; struct regulator_dev *vddh_rdev; u64 stats[ARRAY_SIZE(qca83xx_hw_stats)]; + int led_polarity_mode; }; struct at803x_context { @@ -706,6 +788,9 @@ static int at803x_probe(struct phy_device *phydev) if (!priv) return -ENOMEM; + /* Init LED polarity mode to -1 */ + priv->led_polarity_mode = -1; + phydev->priv = priv; ret = at803x_parse_dt(phydev); @@ -2235,6 +2320,242 @@ static void qca808x_link_change_notify(struct phy_device *phydev) phydev->link ? QCA8081_PHY_FIFO_RSTN : 0); } +static int qca808x_led_parse_netdev(struct phy_device *phydev, unsigned long rules, + u16 *offload_trigger) +{ + /* Parsing specific to netdev trigger */ + if (test_bit(TRIGGER_NETDEV_TX, &rules)) + *offload_trigger |= QCA808X_LED_TX_BLINK; + if (test_bit(TRIGGER_NETDEV_RX, &rules)) + *offload_trigger |= QCA808X_LED_RX_BLINK; + if (test_bit(TRIGGER_NETDEV_LINK_10, &rules)) + *offload_trigger |= QCA808X_LED_SPEED10_ON; + if (test_bit(TRIGGER_NETDEV_LINK_100, &rules)) + *offload_trigger |= QCA808X_LED_SPEED100_ON; + if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules)) + *offload_trigger |= QCA808X_LED_SPEED1000_ON; + if (test_bit(TRIGGER_NETDEV_LINK_2500, &rules)) + *offload_trigger |= QCA808X_LED_SPEED2500_ON; + if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules)) + *offload_trigger |= QCA808X_LED_HALF_DUPLEX_ON; + if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules)) + *offload_trigger |= QCA808X_LED_FULL_DUPLEX_ON; + + if (rules && !*offload_trigger) + return -EOPNOTSUPP; + + /* Enable BLINK_CHECK_BYPASS by default to make the LED + * blink even with duplex or speed mode not enabled. + */ + *offload_trigger |= QCA808X_LED_BLINK_CHECK_BYPASS; + + return 0; +} + +static int qca808x_led_hw_control_enable(struct phy_device *phydev, u8 index) +{ + u16 reg; + + if (index > 2) + return -EINVAL; + + reg = QCA808X_MMD7_LED_FORCE_CTRL(index); + + return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg, + QCA808X_LED_FORCE_EN); +} + +static int qca808x_led_hw_is_supported(struct phy_device *phydev, u8 index, + unsigned long rules) +{ + u16 offload_trigger = 0; + + if (index > 2) + return -EINVAL; + + return qca808x_led_parse_netdev(phydev, rules, &offload_trigger); +} + +static int qca808x_led_hw_control_set(struct phy_device *phydev, u8 index, + unsigned long rules) +{ + u16 reg, offload_trigger = 0; + int ret; + + if (index > 2) + return -EINVAL; + + reg = QCA808X_MMD7_LED_CTRL(index); + + ret = qca808x_led_parse_netdev(phydev, rules, &offload_trigger); + if (ret) + return ret; + + ret = qca808x_led_hw_control_enable(phydev, index); + if (ret) + return ret; + + return phy_modify_mmd(phydev, MDIO_MMD_AN, reg, + QCA808X_LED_PATTERN_MASK, + offload_trigger); +} + +static bool qca808x_led_hw_control_status(struct phy_device *phydev, u8 index) +{ + u16 reg; + int val; + + if (index > 2) + return false; + + reg = QCA808X_MMD7_LED_FORCE_CTRL(index); + + val = phy_read_mmd(phydev, MDIO_MMD_AN, reg); + + return !(val & QCA808X_LED_FORCE_EN); +} + +static int qca808x_led_hw_control_get(struct phy_device *phydev, u8 index, + unsigned long *rules) +{ + u16 reg; + int val; + + if (index > 2) + return -EINVAL; + + /* Check if we have hw control enabled */ + if (qca808x_led_hw_control_status(phydev, index)) + return -EINVAL; + + reg = QCA808X_MMD7_LED_CTRL(index); + + val = phy_read_mmd(phydev, MDIO_MMD_AN, reg); + if (val & QCA808X_LED_TX_BLINK) + set_bit(TRIGGER_NETDEV_TX, rules); + if (val & QCA808X_LED_RX_BLINK) + set_bit(TRIGGER_NETDEV_RX, rules); + if (val & QCA808X_LED_SPEED10_ON) + set_bit(TRIGGER_NETDEV_LINK_10, rules); + if (val & QCA808X_LED_SPEED100_ON) + set_bit(TRIGGER_NETDEV_LINK_100, rules); + if (val & QCA808X_LED_SPEED1000_ON) + set_bit(TRIGGER_NETDEV_LINK_1000, rules); + if (val & QCA808X_LED_SPEED2500_ON) + set_bit(TRIGGER_NETDEV_LINK_2500, rules); + if (val & QCA808X_LED_HALF_DUPLEX_ON) + set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules); + if (val & QCA808X_LED_FULL_DUPLEX_ON) + set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules); + + return 0; +} + +static int qca808x_led_hw_control_reset(struct phy_device *phydev, u8 index) +{ + u16 reg; + + if (index > 2) + return -EINVAL; + + reg = QCA808X_MMD7_LED_CTRL(index); + + return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg, + QCA808X_LED_PATTERN_MASK); +} + +static int qca808x_led_brightness_set(struct phy_device *phydev, + u8 index, enum led_brightness value) +{ + u16 reg; + int ret; + + if (index > 2) + return -EINVAL; + + if (!value) { + ret = qca808x_led_hw_control_reset(phydev, index); + if (ret) + return ret; + } + + reg = QCA808X_MMD7_LED_FORCE_CTRL(index); + + return phy_modify_mmd(phydev, MDIO_MMD_AN, reg, + QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK, + QCA808X_LED_FORCE_EN | value ? QCA808X_LED_FORCE_ON : + QCA808X_LED_FORCE_OFF); +} + +static int qca808x_led_blink_set(struct phy_device *phydev, u8 index, + unsigned long *delay_on, + unsigned long *delay_off) +{ + int ret; + u16 reg; + + if (index > 2) + return -EINVAL; + + reg = QCA808X_MMD7_LED_FORCE_CTRL(index); + + /* Set blink to 50% off, 50% on at 4Hz by default */ + ret = phy_modify_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_LED_GLOBAL, + QCA808X_LED_BLINK_FREQ_MASK | QCA808X_LED_BLINK_DUTY_MASK, + QCA808X_LED_BLINK_FREQ_4HZ | QCA808X_LED_BLINK_DUTY_50_50); + if (ret) + return ret; + + /* We use BLINK_1 for normal blinking */ + ret = phy_modify_mmd(phydev, MDIO_MMD_AN, reg, + QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK, + QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_BLINK_1); + if (ret) + return ret; + + /* We set blink to 4Hz, aka 250ms */ + *delay_on = 250 / 2; + *delay_off = 250 / 2; + + return 0; +} + +static int qca808x_led_polarity_set(struct phy_device *phydev, int index, + unsigned long modes) +{ + struct at803x_priv *priv = phydev->priv; + bool active_low = false; + u32 mode; + + for_each_set_bit(mode, &modes, __PHY_LED_MODES_NUM) { + switch (mode) { + case PHY_LED_ACTIVE_LOW: + active_low = true; + break; + default: + return -EINVAL; + } + } + + /* PHY polarity is global and can't be set per LED. + * To detect this, check if last requested polarity mode + * match the new one. + */ + if (priv->led_polarity_mode >= 0 && + priv->led_polarity_mode != active_low) { + phydev_err(phydev, "PHY polarity is global. Mismatched polarity on different LED\n"); + return -EINVAL; + } + + /* Save the last PHY polarity mode */ + priv->led_polarity_mode = active_low; + + return phy_modify_mmd(phydev, MDIO_MMD_AN, + QCA808X_MMD7_LED_POLARITY_CTRL, + QCA808X_LED_ACTIVE_HIGH, + active_low ? 0 : QCA808X_LED_ACTIVE_HIGH); +} + static struct phy_driver at803x_driver[] = { { /* Qualcomm Atheros AR8035 */ @@ -2411,6 +2732,12 @@ static struct phy_driver at803x_driver[] = { .cable_test_start = qca808x_cable_test_start, .cable_test_get_status = qca808x_cable_test_get_status, .link_change_notify = qca808x_link_change_notify, + .led_brightness_set = qca808x_led_brightness_set, + .led_blink_set = qca808x_led_blink_set, + .led_hw_is_supported = qca808x_led_hw_is_supported, + .led_hw_control_set = qca808x_led_hw_control_set, + .led_hw_control_get = qca808x_led_hw_control_get, + .led_polarity_set = qca808x_led_polarity_set, }, }; module_phy_driver(at803x_driver); diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c index 3611ea64875e..dd778c7fde1d 100644 --- a/drivers/net/phy/phy_device.c +++ b/drivers/net/phy/phy_device.c @@ -3097,6 +3097,7 @@ static int of_phy_led(struct phy_device *phydev, struct device *dev = &phydev->mdio.dev; struct led_init_data init_data = {}; struct led_classdev *cdev; + unsigned long modes = 0; struct phy_led *phyled; u32 index; int err; @@ -3114,6 +3115,21 @@ static int of_phy_led(struct phy_device *phydev, if (index > U8_MAX) return -EINVAL; + if (of_property_read_bool(led, "active-low")) + set_bit(PHY_LED_ACTIVE_LOW, &modes); + if (of_property_read_bool(led, "inactive-high-impedance")) + set_bit(PHY_LED_INACTIVE_HIGH_IMPEDANCE, &modes); + + if (modes) { + /* Return error if asked to set polarity modes but not supported */ + if (!phydev->drv->led_polarity_set) + return -EINVAL; + + err = phydev->drv->led_polarity_set(phydev, index, modes); + if (err) + return err; + } + phyled->index = index; if (phydev->drv->led_brightness_set) cdev->brightness_set_blocking = phy_led_set_brightness; diff --git a/include/linux/phy.h b/include/linux/phy.h index 684efaeca07c..c9994a59ca2e 100644 --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -852,6 +852,15 @@ struct phy_plca_status { bool pst; }; +/* Modes for PHY LED configuration */ +enum phy_led_modes { + PHY_LED_ACTIVE_LOW = 0, + PHY_LED_INACTIVE_HIGH_IMPEDANCE = 1, + + /* keep it last */ + __PHY_LED_MODES_NUM, +}; + /** * struct phy_led: An LED driven by the PHY * @@ -1145,6 +1154,19 @@ struct phy_driver { int (*led_hw_control_get)(struct phy_device *dev, u8 index, unsigned long *rules); + /** + * @led_polarity_set: Set the LED polarity modes + * @dev: PHY device which has the LED + * @index: Which LED of the PHY device + * @modes: bitmap of LED polarity modes + * + * Configure LED with all the required polarity modes in @modes + * to make it correctly turn ON or OFF. + * + * Returns 0, or an error code. + */ + int (*led_polarity_set)(struct phy_device *dev, int index, + unsigned long modes); }; #define to_phy_driver(d) container_of(to_mdio_common_driver(d), \ struct phy_driver, mdiodrv) |