diff options
| -rw-r--r-- | drivers/regulator/mc13892-regulator.c | 72 |
1 files changed, 56 insertions, 16 deletions
diff --git a/drivers/regulator/mc13892-regulator.c b/drivers/regulator/mc13892-regulator.c index 0d84b1f33199..5dd8aaa5cfb8 100644 --- a/drivers/regulator/mc13892-regulator.c +++ b/drivers/regulator/mc13892-regulator.c @@ -164,6 +164,14 @@ static const unsigned int mc13892_sw1[] = { 1350000, 1375000 }; +/* + * Note: this table is used to derive SWxVSEL by index into + * the array. Offset the values by the index of 1100000uV + * to get the actual register value for that voltage selector + * if the HI bit is to be set as well. + */ +#define MC13892_SWxHI_SEL_OFFSET 20 + static const unsigned int mc13892_sw[] = { 600000, 625000, 650000, 675000, 700000, 725000, 750000, 775000, 800000, 825000, 850000, 875000, @@ -239,7 +247,6 @@ static const unsigned int mc13892_pwgtdrv[] = { }; static struct regulator_ops mc13892_gpo_regulator_ops; -/* sw regulators need special care due to the "hi bit" */ static struct regulator_ops mc13892_sw_regulator_ops; @@ -396,7 +403,7 @@ static int mc13892_sw_regulator_get_voltage_sel(struct regulator_dev *rdev) { struct mc13xxx_regulator_priv *priv = rdev_get_drvdata(rdev); int ret, id = rdev_get_id(rdev); - unsigned int val; + unsigned int val, selector; dev_dbg(rdev_get_dev(rdev), "%s id: %d\n", __func__, id); @@ -407,12 +414,28 @@ static int mc13892_sw_regulator_get_voltage_sel(struct regulator_dev *rdev) if (ret) return ret; - val = (val & mc13892_regulators[id].vsel_mask) - >> mc13892_regulators[id].vsel_shift; + /* + * Figure out if the HI bit is set inside the switcher mode register + * since this means the selector value we return is at a different + * offset into the selector table. + * + * According to the MC13892 documentation note 59 (Table 47) the SW1 + * buck switcher does not support output range programming therefore + * the HI bit must always remain 0. So do not do anything strange if + * our register is MC13892_SWITCHERS0. + */ + + selector = val & mc13892_regulators[id].vsel_mask; + + if ((mc13892_regulators[id].vsel_reg != MC13892_SWITCHERS0) && + (val & MC13892_SWITCHERS0_SWxHI)) { + selector += MC13892_SWxHI_SEL_OFFSET; + } - dev_dbg(rdev_get_dev(rdev), "%s id: %d val: %d\n", __func__, id, val); + dev_dbg(rdev_get_dev(rdev), "%s id: %d val: 0x%08x selector: %d\n", + __func__, id, val, selector); - return val; + return selector; } static int mc13892_sw_regulator_set_voltage_sel(struct regulator_dev *rdev, @@ -425,18 +448,35 @@ static int mc13892_sw_regulator_set_voltage_sel(struct regulator_dev *rdev, volt = rdev->desc->volt_table[selector]; mask = mc13892_regulators[id].vsel_mask; - reg_value = selector << mc13892_regulators[id].vsel_shift; - - if (volt > 1375000) { - mask |= MC13892_SWITCHERS0_SWxHI; - reg_value |= MC13892_SWITCHERS0_SWxHI; - } else if (volt < 1100000) { - mask |= MC13892_SWITCHERS0_SWxHI; - reg_value &= ~MC13892_SWITCHERS0_SWxHI; + reg_value = selector; + + /* + * Don't mess with the HI bit or support HI voltage offsets for SW1. + * + * Since the get_voltage_sel callback has given a fudged value for + * the selector offset, we need to back out that offset if HI is + * to be set so we write the correct value to the register. + * + * The HI bit addition and selector offset handling COULD be more + * complicated by shifting and masking off the voltage selector part + * of the register then logical OR it back in, but since the selector + * is at bits 4:0 there is very little point. This makes the whole + * thing more readable and we do far less work. + */ + + if (mc13892_regulators[id].vsel_reg != MC13892_SWITCHERS0) { + if (volt > 1375000) { + reg_value -= MC13892_SWxHI_SEL_OFFSET; + reg_value |= MC13892_SWITCHERS0_SWxHI; + mask |= MC13892_SWITCHERS0_SWxHI; + } else if (volt < 1100000) { + reg_value &= ~MC13892_SWITCHERS0_SWxHI; + mask |= MC13892_SWITCHERS0_SWxHI; + } } mc13xxx_lock(priv->mc13xxx); - ret = mc13xxx_reg_rmw(priv->mc13xxx, mc13892_regulators[id].reg, mask, + ret = mc13xxx_reg_rmw(priv->mc13xxx, mc13892_regulators[id].vsel_reg, mask, reg_value); mc13xxx_unlock(priv->mc13xxx); @@ -520,7 +560,7 @@ static int mc13892_regulator_probe(struct platform_device *pdev) if (ret) goto err_unlock; - /* enable switch auto mode */ + /* enable switch auto mode (on 2.0A silicon only) */ if ((val & 0x0000FFFF) == 0x45d0) { ret = mc13xxx_reg_rmw(mc13892, MC13892_SWITCHERS4, MC13892_SWITCHERS4_SW1MODE_M | |