diff options
| -rw-r--r-- | drivers/crypto/caam/error.c | 77 |
1 files changed, 18 insertions, 59 deletions
diff --git a/drivers/crypto/caam/error.c b/drivers/crypto/caam/error.c index 0f4725cc8039..6531054a44c8 100644 --- a/drivers/crypto/caam/error.c +++ b/drivers/crypto/caam/error.c @@ -16,13 +16,10 @@ static const struct { const char *error_text; } desc_error_list[] = { { 0x00, "No error." }, - { 0x01, "SGT Length Error. The descriptor is trying to read " - "more data than is contained in the SGT table." }, + { 0x01, "SGT Length Error. The descriptor is trying to read more data than is contained in the SGT table." }, { 0x02, "SGT Null Entry Error." }, - { 0x03, "Job Ring Control Error. There is a bad value in the " - "Job Ring Control register." }, - { 0x04, "Invalid Descriptor Command. The Descriptor Command " - "field is invalid." }, + { 0x03, "Job Ring Control Error. There is a bad value in the Job Ring Control register." }, + { 0x04, "Invalid Descriptor Command. The Descriptor Command field is invalid." }, { 0x05, "Reserved." }, { 0x06, "Invalid KEY Command" }, { 0x07, "Invalid LOAD Command" }, @@ -31,55 +28,26 @@ static const struct { { 0x0A, "Invalid FIFO LOAD Command" }, { 0x0B, "Invalid FIFO STORE Command" }, { 0x0C, "Invalid MOVE/MOVE_LEN Command" }, - { 0x0D, "Invalid JUMP Command. A nonlocal JUMP Command is " - "invalid because the target is not a Job Header " - "Command, or the jump is from a Trusted Descriptor to " - "a Job Descriptor, or because the target Descriptor " - "contains a Shared Descriptor." }, + { 0x0D, "Invalid JUMP Command. A nonlocal JUMP Command is invalid because the target is not a Job Header Command, or the jump is from a Trusted Descriptor to a Job Descriptor, or because the target Descriptor contains a Shared Descriptor." }, { 0x0E, "Invalid MATH Command" }, { 0x0F, "Invalid SIGNATURE Command" }, - { 0x10, "Invalid Sequence Command. A SEQ IN PTR OR SEQ OUT PTR " - "Command is invalid or a SEQ KEY, SEQ LOAD, SEQ FIFO " - "LOAD, or SEQ FIFO STORE decremented the input or " - "output sequence length below 0. This error may result " - "if a built-in PROTOCOL Command has encountered a " - "malformed PDU." }, + { 0x10, "Invalid Sequence Command. A SEQ IN PTR OR SEQ OUT PTR Command is invalid or a SEQ KEY, SEQ LOAD, SEQ FIFO LOAD, or SEQ FIFO STORE decremented the input or output sequence length below 0. This error may result if a built-in PROTOCOL Command has encountered a malformed PDU." }, { 0x11, "Skip data type invalid. The type must be 0xE or 0xF."}, { 0x12, "Shared Descriptor Header Error" }, - { 0x13, "Header Error. Invalid length or parity, or certain " - "other problems." }, - { 0x14, "Burster Error. Burster has gotten to an illegal " - "state" }, - { 0x15, "Context Register Length Error. The descriptor is " - "trying to read or write past the end of the Context " - "Register. A SEQ LOAD or SEQ STORE with the VLF bit " - "set was executed with too large a length in the " - "variable length register (VSOL for SEQ STORE or VSIL " - "for SEQ LOAD)." }, + { 0x13, "Header Error. Invalid length or parity, or certain other problems." }, + { 0x14, "Burster Error. Burster has gotten to an illegal state" }, + { 0x15, "Context Register Length Error. The descriptor is trying to read or write past the end of the Context Register. A SEQ LOAD or SEQ STORE with the VLF bit set was executed with too large a length in the variable length register (VSOL for SEQ STORE or VSIL for SEQ LOAD)." }, { 0x16, "DMA Error" }, { 0x17, "Reserved." }, { 0x1A, "Job failed due to JR reset" }, { 0x1B, "Job failed due to Fail Mode" }, { 0x1C, "DECO Watchdog timer timeout error" }, - { 0x1D, "DECO tried to copy a key from another DECO but the " - "other DECO's Key Registers were locked" }, - { 0x1E, "DECO attempted to copy data from a DECO that had an " - "unmasked Descriptor error" }, - { 0x1F, "LIODN error. DECO was trying to share from itself or " - "from another DECO but the two Non-SEQ LIODN values " - "didn't match or the 'shared from' DECO's Descriptor " - "required that the SEQ LIODNs be the same and they " - "aren't." }, - { 0x20, "DECO has completed a reset initiated via the DRR " - "register" }, - { 0x21, "Nonce error. When using EKT (CCM) key encryption " - "option in the FIFO STORE Command, the Nonce counter " - "reached its maximum value and this encryption mode " - "can no longer be used." }, - { 0x22, "Meta data is too large (> 511 bytes) for TLS decap " - "(input frame; block ciphers) and IPsec decap (output " - "frame, when doing the next header byte update) and " - "DCRC (output frame)." }, + { 0x1D, "DECO tried to copy a key from another DECO but the other DECO's Key Registers were locked" }, + { 0x1E, "DECO attempted to copy data from a DECO that had an unmasked Descriptor error" }, + { 0x1F, "LIODN error. DECO was trying to share from itself or from another DECO but the two Non-SEQ LIODN values didn't match or the 'shared from' DECO's Descriptor required that the SEQ LIODNs be the same and they aren't." }, + { 0x20, "DECO has completed a reset initiated via the DRR register" }, + { 0x21, "Nonce error. When using EKT (CCM) key encryption option in the FIFO STORE Command, the Nonce counter reached its maximum value and this encryption mode can no longer be used." }, + { 0x22, "Meta data is too large (> 511 bytes) for TLS decap (input frame; block ciphers) and IPsec decap (output frame, when doing the next header byte update) and DCRC (output frame)." }, { 0x23, "Read Input Frame error" }, { 0x24, "JDKEK, TDKEK or TDSK not loaded error" }, { 0x80, "DNR (do not run) error" }, @@ -90,23 +58,14 @@ static const struct { { 0x85, "Sequence number overflow" }, { 0x86, "Sigver invalid signature" }, { 0x87, "DSA Sign Illegal test descriptor" }, - { 0x88, "Protocol Format Error - A protocol has seen an error " - "in the format of data received. When running RSA, " - "this means that formatting with random padding was " - "used, and did not follow the form: 0x00, 0x02, 8-to-N " - "bytes of non-zero pad, 0x00, F data." }, - { 0x89, "Protocol Size Error - A protocol has seen an error in " - "size. When running RSA, pdb size N < (size of F) when " - "no formatting is used; or pdb size N < (F + 11) when " - "formatting is used." }, + { 0x88, "Protocol Format Error - A protocol has seen an error in the format of data received. When running RSA, this means that formatting with random padding was used, and did not follow the form: 0x00, 0x02, 8-to-N bytes of non-zero pad, 0x00, F data." }, + { 0x89, "Protocol Size Error - A protocol has seen an error in size. When running RSA, pdb size N < (size of F) when no formatting is used; or pdb size N < (F + 11) when formatting is used." }, { 0xC1, "Blob Command error: Undefined mode" }, { 0xC2, "Blob Command error: Secure Memory Blob mode error" }, - { 0xC4, "Blob Command error: Black Blob key or input size " - "error" }, + { 0xC4, "Blob Command error: Black Blob key or input size error" }, { 0xC5, "Blob Command error: Invalid key destination" }, { 0xC8, "Blob Command error: Trusted/Secure mode error" }, - { 0xF0, "IPsec TTL or hop limit field either came in as 0, " - "or was decremented to 0" }, + { 0xF0, "IPsec TTL or hop limit field either came in as 0, or was decremented to 0" }, { 0xF1, "3GPP HFN matches or exceeds the Threshold" }, }; |