1 files changed, 0 insertions, 94 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
deleted file mode 100644
index 8146193bd8ac..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
+++ /dev/null
@@ -1,94 +0,0 @@
-== Amlogic Meson pinmux controller ==
-
-Required properties for the root node:
- - compatible: one of "amlogic,meson8-cbus-pinctrl"
-		      "amlogic,meson8b-cbus-pinctrl"
-		      "amlogic,meson8m2-cbus-pinctrl"
-		      "amlogic,meson8-aobus-pinctrl"
-		      "amlogic,meson8b-aobus-pinctrl"
-		      "amlogic,meson8m2-aobus-pinctrl"
-		      "amlogic,meson-gxbb-periphs-pinctrl"
-		      "amlogic,meson-gxbb-aobus-pinctrl"
-		      "amlogic,meson-gxl-periphs-pinctrl"
-		      "amlogic,meson-gxl-aobus-pinctrl"
-		      "amlogic,meson-axg-periphs-pinctrl"
-		      "amlogic,meson-axg-aobus-pinctrl"
-		      "amlogic,meson-g12a-periphs-pinctrl"
-		      "amlogic,meson-g12a-aobus-pinctrl"
-		      "amlogic,meson-a1-periphs-pinctrl"
-		      "amlogic,meson-s4-periphs-pinctrl"
- - reg: address and size of registers controlling irq functionality
-
-=== GPIO sub-nodes ===
-
-The GPIO bank for the controller is represented as a sub-node and it acts as a
-GPIO controller.
-
-Required properties for sub-nodes are:
- - reg: should contain a list of address and size, one tuple for each entry
-   in reg-names.
- - reg-names: an array of strings describing the "reg" entries.
-   Must contain "mux" and "gpio".
-   May contain "pull", "pull-enable" and "ds" when appropriate.
- - gpio-controller: identifies the node as a gpio controller
- - #gpio-cells: must be 2
-
-=== Other sub-nodes ===
-
-Child nodes without the "gpio-controller" represent some desired
-configuration for a pin or a group. Those nodes can be pinmux nodes or
-configuration nodes.
-
-Required properties for pinmux nodes are:
- - groups: a list of pinmux groups. The list of all available groups
-   depends on the SoC and can be found in driver sources.
- - function: the name of a function to activate for the specified set
-   of groups. The list of all available functions depends on the SoC
-   and can be found in driver sources.
-
-Required properties for configuration nodes:
- - pins: a list of pin names
-
-Configuration nodes support the following generic properties, as
-described in file pinctrl-bindings.txt:
- - "bias-disable"
- - "bias-pull-up"
- - "bias-pull-down"
- - "output-enable"
- - "output-disable"
- - "output-low"
- - "output-high"
-
-Optional properties :
- - drive-strength-microamp: Drive strength for the specified pins in uA.
-			    This property is only valid for G12A and newer.
-
-=== Example ===
-
-	pinctrl: pinctrl@c1109880 {
-		compatible = "amlogic,meson8-cbus-pinctrl";
-		reg = <0xc1109880 0x10>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		gpio: banks@c11080b0 {
-			reg = <0xc11080b0 0x28>,
-			      <0xc11080e8 0x18>,
-			      <0xc1108120 0x18>,
-			      <0xc1108030 0x30>;
-			reg-names = "mux", "pull", "pull-enable", "gpio";
-			gpio-controller;
-			#gpio-cells = <2>;
-               };
-
-		nand {
-			mux {
-				groups = "nand_io", "nand_io_ce0", "nand_io_ce1",
-					 "nand_io_rb0", "nand_ale", "nand_cle",
-					 "nand_wen_clk", "nand_ren_clk", "nand_dqs",
-					 "nand_ce2", "nand_ce3";
-				function = "nand";
-			};
-		};
-	};