diff options
Diffstat (limited to 'Documentation/hwmon')
| -rw-r--r-- | Documentation/hwmon/adt7475 | 87 | ||||
| -rw-r--r-- | Documentation/hwmon/lis3lv02d | 30 |
2 files changed, 104 insertions, 13 deletions
diff --git a/Documentation/hwmon/adt7475 b/Documentation/hwmon/adt7475 new file mode 100644 index 000000000000..a2b1abec850e --- /dev/null +++ b/Documentation/hwmon/adt7475 @@ -0,0 +1,87 @@ +This describes the interface for the ADT7475 driver: + +(there are 4 fans, numbered fan1 to fan4): + +fanX_input Read the current speed of the fan (in RPMs) +fanX_min Read/write the minimum speed of the fan. Dropping + below this sets an alarm. + +(there are three PWMs, numbered pwm1 to pwm3): + +pwmX Read/write the current duty cycle of the PWM. Writes + only have effect when auto mode is turned off (see + below). Range is 0 - 255. + +pwmX_enable Fan speed control method: + + 0 - No control (fan at full speed) + 1 - Manual fan speed control (using pwm[1-*]) + 2 - Automatic fan speed control + +pwmX_auto_channels_temp Select which channels affect this PWM + + 1 - TEMP1 controls PWM + 2 - TEMP2 controls PWM + 4 - TEMP3 controls PWM + 6 - TEMP2 and TEMP3 control PWM + 7 - All three inputs control PWM + +pwmX_freq Read/write the PWM frequency in Hz. The number + should be one of the following: + + 11 Hz + 14 Hz + 22 Hz + 29 Hz + 35 Hz + 44 Hz + 58 Hz + 88 Hz + +pwmX_auto_point1_pwm Read/write the minimum PWM duty cycle in automatic mode + +pwmX_auto_point2_pwm Read/write the maximum PWM duty cycle in automatic mode + +(there are three temperature settings numbered temp1 to temp3): + +tempX_input Read the current temperature. The value is in milli + degrees of Celsius. + +tempX_max Read/write the upper temperature limit - exceeding this + will cause an alarm. + +tempX_min Read/write the lower temperature limit - exceeding this + will cause an alarm. + +tempX_offset Read/write the temperature adjustment offset + +tempX_crit Read/write the THERM limit for remote1. + +tempX_crit_hyst Set the temperature value below crit where the + fans will stay on - this helps drive the temperature + low enough so it doesn't stay near the edge and + cause THERM to keep tripping. + +tempX_auto_point1_temp Read/write the minimum temperature where the fans will + turn on in automatic mode. + +tempX_auto_point2_temp Read/write the maximum temperature over which the fans + will run in automatic mode. tempX_auto_point1_temp + and tempX_auto_point2_temp together define the + range of automatic control. + +tempX_alarm Read a 1 if the max/min alarm is set +tempX_fault Read a 1 if either temp1 or temp3 diode has a fault + +(There are two voltage settings, in1 and in2): + +inX_input Read the current voltage on VCC. Value is in + millivolts. + +inX_min read/write the minimum voltage limit. + Dropping below this causes an alarm. + +inX_max read/write the maximum voltage limit. + Exceeding this causes an alarm. + +inX_alarm Read a 1 if the max/min alarm is set. diff --git a/Documentation/hwmon/lis3lv02d b/Documentation/hwmon/lis3lv02d index 65dfb0c0fd67..0fcfc4a7ccdc 100644 --- a/Documentation/hwmon/lis3lv02d +++ b/Documentation/hwmon/lis3lv02d @@ -13,18 +13,21 @@ Author: Description ----------- -This driver provides support for the accelerometer found in various HP laptops -sporting the feature officially called "HP Mobile Data Protection System 3D" or -"HP 3D DriveGuard". It detect automatically laptops with this sensor. Known models -(for now the HP 2133, nc6420, nc2510, nc8510, nc84x0, nw9440 and nx9420) will -have their axis automatically oriented on standard way (eg: you can directly -play neverball). The accelerometer data is readable via +This driver provides support for the accelerometer found in various HP +laptops sporting the feature officially called "HP Mobile Data +Protection System 3D" or "HP 3D DriveGuard". It detect automatically +laptops with this sensor. Known models (for now the HP 2133, nc6420, +nc2510, nc8510, nc84x0, nw9440 and nx9420) will have their axis +automatically oriented on standard way (eg: you can directly play +neverball). The accelerometer data is readable via /sys/devices/platform/lis3lv02d. Sysfs attributes under /sys/devices/platform/lis3lv02d/: position - 3D position that the accelerometer reports. Format: "(x,y,z)" -calibrate - read: values (x, y, z) that are used as the base for input class device operation. - write: forces the base to be recalibrated with the current position. +calibrate - read: values (x, y, z) that are used as the base for input + class device operation. + write: forces the base to be recalibrated with the current + position. rate - reports the sampling rate of the accelerometer device in HZ This driver also provides an absolute input class device, allowing @@ -39,11 +42,12 @@ the accelerometer are converted into a "standard" organisation of the axes * When the laptop is horizontal the position reported is about 0 for X and Y and a positive value for Z * If the left side is elevated, X increases (becomes positive) - * If the front side (where the touchpad is) is elevated, Y decreases (becomes negative) + * If the front side (where the touchpad is) is elevated, Y decreases + (becomes negative) * If the laptop is put upside-down, Z becomes negative -If your laptop model is not recognized (cf "dmesg"), you can send an email to the -authors to add it to the database. When reporting a new laptop, please include -the output of "dmidecode" plus the value of /sys/devices/platform/lis3lv02d/position -in these four cases. +If your laptop model is not recognized (cf "dmesg"), you can send an +email to the authors to add it to the database. When reporting a new +laptop, please include the output of "dmidecode" plus the value of +/sys/devices/platform/lis3lv02d/position in these four cases. |