diff options
Diffstat (limited to 'drivers/net/dsa/b53/b53_common.c')
| -rw-r--r-- | drivers/net/dsa/b53/b53_common.c | 87 |
1 files changed, 48 insertions, 39 deletions
diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c index 3867f3d4545f..77501f9c5915 100644 --- a/drivers/net/dsa/b53/b53_common.c +++ b/drivers/net/dsa/b53/b53_common.c @@ -1309,46 +1309,50 @@ void b53_port_event(struct dsa_switch *ds, int port) } EXPORT_SYMBOL(b53_port_event); -void b53_phylink_validate(struct dsa_switch *ds, int port, - unsigned long *supported, - struct phylink_link_state *state) +static void b53_phylink_get_caps(struct dsa_switch *ds, int port, + struct phylink_config *config) { struct b53_device *dev = ds->priv; - __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, }; - if (dev->ops->serdes_phylink_validate) - dev->ops->serdes_phylink_validate(dev, port, mask, state); + /* Internal ports need GMII for PHYLIB */ + __set_bit(PHY_INTERFACE_MODE_GMII, config->supported_interfaces); + + /* These switches appear to support MII and RevMII too, but beyond + * this, the code gives very few clues. FIXME: We probably need more + * interface modes here. + * + * According to b53_srab_mux_init(), ports 3..5 can support: + * SGMII, MII, GMII, RGMII or INTERNAL depending on the MUX setting. + * However, the interface mode read from the MUX configuration is + * not passed back to DSA, so phylink uses NA. + * DT can specify RGMII for ports 0, 1. + * For MDIO, port 8 can be RGMII_TXID. + */ + __set_bit(PHY_INTERFACE_MODE_MII, config->supported_interfaces); + __set_bit(PHY_INTERFACE_MODE_REVMII, config->supported_interfaces); - /* Allow all the expected bits */ - phylink_set(mask, Autoneg); - phylink_set_port_modes(mask); - phylink_set(mask, Pause); - phylink_set(mask, Asym_Pause); + config->mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | + MAC_10 | MAC_100; - /* With the exclusion of 5325/5365, MII, Reverse MII and 802.3z, we - * support Gigabit, including Half duplex. + /* 5325/5365 are not capable of gigabit speeds, everything else is. + * Note: the original code also exclulded Gigagbit for MII, RevMII + * and 802.3z modes. MII and RevMII are not able to work above 100M, + * so will be excluded by the generic validator implementation. + * However, the exclusion of Gigabit for 802.3z just seems wrong. */ - if (state->interface != PHY_INTERFACE_MODE_MII && - state->interface != PHY_INTERFACE_MODE_REVMII && - !phy_interface_mode_is_8023z(state->interface) && - !(is5325(dev) || is5365(dev))) { - phylink_set(mask, 1000baseT_Full); - phylink_set(mask, 1000baseT_Half); - } + if (!(is5325(dev) || is5365(dev))) + config->mac_capabilities |= MAC_1000; - if (!phy_interface_mode_is_8023z(state->interface)) { - phylink_set(mask, 10baseT_Half); - phylink_set(mask, 10baseT_Full); - phylink_set(mask, 100baseT_Half); - phylink_set(mask, 100baseT_Full); - } + /* Get the implementation specific capabilities */ + if (dev->ops->phylink_get_caps) + dev->ops->phylink_get_caps(dev, port, config); - linkmode_and(supported, supported, mask); - linkmode_and(state->advertising, state->advertising, mask); - - phylink_helper_basex_speed(state); + /* This driver does not make use of the speed, duplex, pause or the + * advertisement in its mac_config, so it is safe to mark this driver + * as non-legacy. + */ + config->legacy_pre_march2020 = false; } -EXPORT_SYMBOL(b53_phylink_validate); int b53_phylink_mac_link_state(struct dsa_switch *ds, int port, struct phylink_link_state *state) @@ -1704,7 +1708,8 @@ static int b53_arl_op(struct b53_device *dev, int op, int port, } int b53_fdb_add(struct dsa_switch *ds, int port, - const unsigned char *addr, u16 vid) + const unsigned char *addr, u16 vid, + struct dsa_db db) { struct b53_device *priv = ds->priv; int ret; @@ -1724,7 +1729,8 @@ int b53_fdb_add(struct dsa_switch *ds, int port, EXPORT_SYMBOL(b53_fdb_add); int b53_fdb_del(struct dsa_switch *ds, int port, - const unsigned char *addr, u16 vid) + const unsigned char *addr, u16 vid, + struct dsa_db db) { struct b53_device *priv = ds->priv; int ret; @@ -1825,7 +1831,8 @@ int b53_fdb_dump(struct dsa_switch *ds, int port, EXPORT_SYMBOL(b53_fdb_dump); int b53_mdb_add(struct dsa_switch *ds, int port, - const struct switchdev_obj_port_mdb *mdb) + const struct switchdev_obj_port_mdb *mdb, + struct dsa_db db) { struct b53_device *priv = ds->priv; int ret; @@ -1845,7 +1852,8 @@ int b53_mdb_add(struct dsa_switch *ds, int port, EXPORT_SYMBOL(b53_mdb_add); int b53_mdb_del(struct dsa_switch *ds, int port, - const struct switchdev_obj_port_mdb *mdb) + const struct switchdev_obj_port_mdb *mdb, + struct dsa_db db) { struct b53_device *priv = ds->priv; int ret; @@ -1861,7 +1869,7 @@ int b53_mdb_del(struct dsa_switch *ds, int port, EXPORT_SYMBOL(b53_mdb_del); int b53_br_join(struct dsa_switch *ds, int port, struct dsa_bridge bridge, - bool *tx_fwd_offload) + bool *tx_fwd_offload, struct netlink_ext_ack *extack) { struct b53_device *dev = ds->priv; s8 cpu_port = dsa_to_port(ds, port)->cpu_dp->index; @@ -2102,7 +2110,8 @@ out: EXPORT_SYMBOL(b53_get_tag_protocol); int b53_mirror_add(struct dsa_switch *ds, int port, - struct dsa_mall_mirror_tc_entry *mirror, bool ingress) + struct dsa_mall_mirror_tc_entry *mirror, bool ingress, + struct netlink_ext_ack *extack) { struct b53_device *dev = ds->priv; u16 reg, loc; @@ -2186,7 +2195,7 @@ int b53_eee_init(struct dsa_switch *ds, int port, struct phy_device *phy) { int ret; - ret = phy_init_eee(phy, 0); + ret = phy_init_eee(phy, false); if (ret) return 0; @@ -2259,7 +2268,7 @@ static const struct dsa_switch_ops b53_switch_ops = { .phy_read = b53_phy_read16, .phy_write = b53_phy_write16, .adjust_link = b53_adjust_link, - .phylink_validate = b53_phylink_validate, + .phylink_get_caps = b53_phylink_get_caps, .phylink_mac_link_state = b53_phylink_mac_link_state, .phylink_mac_config = b53_phylink_mac_config, .phylink_mac_an_restart = b53_phylink_mac_an_restart, |