diff options
Diffstat (limited to 'drivers/scsi/lpfc/lpfc_sli.c')
-rw-r--r-- | drivers/scsi/lpfc/lpfc_sli.c | 46 |
1 files changed, 12 insertions, 34 deletions
diff --git a/drivers/scsi/lpfc/lpfc_sli.c b/drivers/scsi/lpfc/lpfc_sli.c index 95caad764fb7..735fa1d484eb 100644 --- a/drivers/scsi/lpfc/lpfc_sli.c +++ b/drivers/scsi/lpfc/lpfc_sli.c @@ -4359,6 +4359,8 @@ lpfc_sli_brdready_s3(struct lpfc_hba *phba, uint32_t mask) if (lpfc_readl(phba->HSregaddr, &status)) return 1; + phba->hba_flag |= HBA_NEEDS_CFG_PORT; + /* * Check status register every 100ms for 5 retries, then every * 500ms for 5, then every 2.5 sec for 5, then reset board and @@ -4687,6 +4689,7 @@ lpfc_sli_brdreset(struct lpfc_hba *phba) /* perform board reset */ phba->fc_eventTag = 0; phba->link_events = 0; + phba->hba_flag |= HBA_NEEDS_CFG_PORT; if (phba->pport) { phba->pport->fc_myDID = 0; phba->pport->fc_prevDID = 0; @@ -5020,6 +5023,8 @@ lpfc_sli_chipset_init(struct lpfc_hba *phba) return -EIO; } + phba->hba_flag |= HBA_NEEDS_CFG_PORT; + /* Clear all interrupt enable conditions */ writel(0, phba->HCregaddr); readl(phba->HCregaddr); /* flush */ @@ -5316,45 +5321,18 @@ int lpfc_sli_hba_setup(struct lpfc_hba *phba) { uint32_t rc; - int mode = 3, i; + int i; int longs; - switch (phba->cfg_sli_mode) { - case 2: - if (phba->cfg_enable_npiv) { - lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT, - "1824 NPIV enabled: Override sli_mode " - "parameter (%d) to auto (0).\n", - phba->cfg_sli_mode); - break; - } - mode = 2; - break; - case 0: - case 3: - break; - default: - lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT, - "1819 Unrecognized sli_mode parameter: %d.\n", - phba->cfg_sli_mode); - - break; + /* Enable ISR already does config_port because of config_msi mbx */ + if (phba->hba_flag & HBA_NEEDS_CFG_PORT) { + rc = lpfc_sli_config_port(phba, LPFC_SLI_REV3); + if (rc) + return -EIO; + phba->hba_flag &= ~HBA_NEEDS_CFG_PORT; } phba->fcp_embed_io = 0; /* SLI4 FC support only */ - rc = lpfc_sli_config_port(phba, mode); - - if (rc && phba->cfg_sli_mode == 3) - lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT, - "1820 Unable to select SLI-3. " - "Not supported by adapter.\n"); - if (rc && mode != 2) - rc = lpfc_sli_config_port(phba, 2); - else if (rc && mode == 2) - rc = lpfc_sli_config_port(phba, 3); - if (rc) - goto lpfc_sli_hba_setup_error; - /* Enable PCIe device Advanced Error Reporting (AER) if configured */ if (phba->cfg_aer_support == 1 && !(phba->hba_flag & HBA_AER_ENABLED)) { rc = pci_enable_pcie_error_reporting(phba->pcidev); |