summaryrefslogtreecommitdiffstats
path: root/arch/x86/xen/setup.c
Commit message (Collapse)AuthorAgeFilesLines
* xen: tolerate ACPI NVS memory overlapping with Xen allocated memoryJuergen Gross2024-09-121-1/+91
| | | | | | | | | | | | | | | | | | | | | | | | | | | In order to minimize required special handling for running as Xen PV dom0, the memory layout is modified to match that of the host. This requires to have only RAM at the locations where Xen allocated memory is living. Unfortunately there seem to be some machines, where ACPI NVS is located at 64 MB, resulting in a conflict with the loaded kernel or the initial page tables built by Xen. Avoid this conflict by swapping the ACPI NVS area in the memory map with unused RAM. This is possible via modification of the dom0 P2M map. Accesses to the ACPI NVS area are done either for saving and restoring it across suspend operations (this will work the same way as before), or by ACPI code when NVS memory is referenced from other ACPI tables. The latter case is handled by a Xen specific indirection of acpi_os_ioremap(). While the E820 map can (and should) be modified right away, the P2M map can be updated only after memory allocation is working, as the P2M map might need to be extended. Fixes: 808fdb71936c ("xen: check for kernel memory conflicting with memory layout") Signed-off-by: Juergen Gross <jgross@suse.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* xen: allow mapping ACPI data using a different physical addressJuergen Gross2024-09-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | When running as a Xen PV dom0 the system needs to map ACPI data of the host using host physical addresses, while those addresses can conflict with the guest physical addresses of the loaded linux kernel. The same problem might apply in case a PV guest is configured to use the host memory map. This conflict can be solved by mapping the ACPI data to a different guest physical address, but mapping the data via acpi_os_ioremap() must still be possible using the host physical address, as this address might be generated by AML when referencing some of the ACPI data. When configured to support running as a Xen PV domain, have an implementation of acpi_os_ioremap() being aware of the possibility to need above mentioned translation of a host physical address to the guest physical address. This modification requires to #include linux/acpi.h in some sources which need to include asm/acpi.h directly. Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* xen: move max_pfn in xen_memory_setup() out of function scopeJuergen Gross2024-09-101-26/+26
| | | | | | | | | | | | | | Instead of having max_pfn as a local variable of xen_memory_setup(), make it a static variable in setup.c instead. This avoids having to pass it to subfunctions, which will be needed in more cases in future. Rename it to ini_nr_pages, as the value denotes the currently usable number of memory pages as passed from the hypervisor at boot time. Signed-off-by: Juergen Gross <jgross@suse.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* xen: move checks for e820 conflicts further upJuergen Gross2024-09-101-22/+22
| | | | | | | | | | | | Move the checks for e820 memory map conflicts using the xen_chk_is_e820_usable() helper further up in order to prepare resolving some of the possible conflicts by doing some e820 map modifications, which must happen before evaluating the RAM layout. Signed-off-by: Juergen Gross <jgross@suse.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* xen: introduce generic helper checking for memory map conflictsJuergen Gross2024-09-101-6/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | When booting as a Xen PV dom0 the memory layout of the dom0 is modified to match that of the host, as this requires less changes in the kernel for supporting Xen. There are some cases, though, which are problematic, as it is the Xen hypervisor selecting the kernel's load address plus some other data, which might conflict with the host's memory map. These conflicts are detected at boot time and result in a boot error. In order to support handling at least some of these conflicts in future, introduce a generic helper function which will later gain the ability to adapt the memory layout when possible. Add the missing check for the xen_start_info area. Note that possible p2m map and initrd memory conflicts are handled already by copying the data to memory areas not conflicting with the memory map. The initial stack allocated by Xen doesn't need to be checked, as early boot code is switching to the statically allocated initial kernel stack. Initial page tables and the kernel itself will be handled later. Signed-off-by: Juergen Gross <jgross@suse.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* xen: use correct end address of kernel for conflict checkingJuergen Gross2024-09-101-1/+1
| | | | | | | | | | | | | | | | | | | | | When running as a Xen PV dom0 the kernel is loaded by the hypervisor using a different memory map than that of the host. In order to minimize the required changes in the kernel, the kernel adapts its memory map to that of the host. In order to do that it is checking for conflicts of its load address with the host memory map. Unfortunately the tested memory range does not include the .brk area, which might result in crashes or memory corruption when this area does conflict with the memory map of the host. Fix the test by using the _end label instead of __bss_stop. Fixes: 808fdb71936c ("xen: check for kernel memory conflicting with memory layout") Signed-off-by: Juergen Gross <jgross@suse.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* minmax: avoid overly complex min()/max() macro arguments in xenLinus Torvalds2024-07-261-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have some very fancy min/max macros that have tons of sanity checking to warn about mixed signedness etc. This is all things that a sane compiler should warn about, but there are no sane compiler interfaces for this, and '-Wsign-compare' is broken [1] and not useful. So then we compensate (some would say over-compensate) by doing the checks manually with some truly horrid macro games. And no, we can't just use __builtin_types_compatible_p(), because the whole question of "does it make sense to compare these two values" is a lot more complicated than that. For example, it makes a ton of sense to compare unsigned values with simple constants like "5", even if that is indeed a signed type. So we have these very strange macros to try to make sensible type checking decisions on the arguments to 'min()' and 'max()'. But that can cause enormous code expansion if the min()/max() macros are used with complicated expressions, and particularly if you nest these things so that you get the first big expansion then expanded again. The xen setup.c file ended up ballooning to over 50MB of preprocessed noise that takes 15s to compile (obviously depending on the build host), largely due to one single line. So let's split that one single line to just be simpler. I think it ends up being more legible to humans too at the same time. Now that single file compiles in under a second. Reported-and-reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Link: https://lore.kernel.org/all/c83c17bb-be75-4c67-979d-54eee38774c6@lucifer.local/ Link: https://staticthinking.wordpress.com/2023/07/25/wsign-compare-is-garbage/ [1] Cc: David Laight <David.Laight@aculab.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* x86/xen: eliminate some private header filesJuergen Gross2024-07-111-1/+0
| | | | | | | | | | | | | | | | | Under arch/x86/xen there is one large private header file xen-ops.h containing most of the Xen-private x86 related declarations, and then there are several small headers with a handful of declarations each. Merge the small headers into xen-ops.h. While doing that, move the declaration of xen_fifo_events from xen-ops.h into include/xen/events.h where it should have been from the beginning. Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Message-ID: <20240710093718.14552-3-jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* x86/xen: attempt to inflate the memory balloon on PVHRoger Pau Monne2024-03-131-44/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When running as PVH or HVM Linux will use holes in the memory map as scratch space to map grants, foreign domain pages and possibly miscellaneous other stuff. However the usage of such memory map holes for Xen purposes can be problematic. The request of holesby Xen happen quite early in the kernel boot process (grant table setup already uses scratch map space), and it's possible that by then not all devices have reclaimed their MMIO space. It's not unlikely for chunks of Xen scratch map space to end up using PCI bridge MMIO window memory, which (as expected) causes quite a lot of issues in the system. At least for PVH dom0 we have the possibility of using regions marked as UNUSABLE in the e820 memory map. Either if the region is UNUSABLE in the native memory map, or it has been converted into UNUSABLE in order to hide RAM regions from dom0, the second stage translation page-tables can populate those areas without issues. PV already has this kind of logic, where the balloon driver is inflated at boot. Re-use the current logic in order to also inflate it when running as PVH. onvert UNUSABLE regions up to the ratio specified in EXTRA_MEM_RATIO to RAM, while reserving them using xen_add_extra_mem() (which is also moved so it's no longer tied to CONFIG_PV). [jgross: fixed build for CONFIG_PVH without CONFIG_XEN_PVH] Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20240220174341.56131-1-roger.pau@citrix.com Signed-off-by: Juergen Gross <jgross@suse.com>
* Merge tag 'dma-mapping-6.6-2023-08-29' of ↵Linus Torvalds2023-08-291-0/+6
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.infradead.org/users/hch/dma-mapping Pull dma-maping updates from Christoph Hellwig: - allow dynamic sizing of the swiotlb buffer, to cater for secure virtualization workloads that require all I/O to be bounce buffered (Petr Tesarik) - move a declaration to a header (Arnd Bergmann) - check for memory region overlap in dma-contiguous (Binglei Wang) - remove the somewhat dangerous runtime swiotlb-xen enablement and unexport is_swiotlb_active (Christoph Hellwig, Juergen Gross) - per-node CMA improvements (Yajun Deng) * tag 'dma-mapping-6.6-2023-08-29' of git://git.infradead.org/users/hch/dma-mapping: swiotlb: optimize get_max_slots() swiotlb: move slot allocation explanation comment where it belongs swiotlb: search the software IO TLB only if the device makes use of it swiotlb: allocate a new memory pool when existing pools are full swiotlb: determine potential physical address limit swiotlb: if swiotlb is full, fall back to a transient memory pool swiotlb: add a flag whether SWIOTLB is allowed to grow swiotlb: separate memory pool data from other allocator data swiotlb: add documentation and rename swiotlb_do_find_slots() swiotlb: make io_tlb_default_mem local to swiotlb.c swiotlb: bail out of swiotlb_init_late() if swiotlb is already allocated dma-contiguous: check for memory region overlap dma-contiguous: support numa CMA for specified node dma-contiguous: support per-numa CMA for all architectures dma-mapping: move arch_dma_set_mask() declaration to header swiotlb: unexport is_swiotlb_active x86: always initialize xen-swiotlb when xen-pcifront is enabling xen/pci: add flag for PCI passthrough being possible
| * xen/pci: add flag for PCI passthrough being possibleJuergen Gross2023-07-311-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | When running as a Xen PV guests passed through PCI devices only have a chance to work if the Xen supplied memory map has some PCI space reserved. Add a flag xen_pv_pci_possible which will be set in early boot in case the memory map has at least one area with the type E820_TYPE_RESERVED. Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
* | x86/xen: Make virt_to_pfn() a static inlineLinus Walleij2023-08-211-2/+2
|/ | | | | | | | | | | | | | | | | | | Making virt_to_pfn() a static inline taking a strongly typed (const void *) makes the contract of a passing a pointer of that type to the function explicit and exposes any misuse of the macro virt_to_pfn() acting polymorphic and accepting many types such as (void *), (unitptr_t) or (unsigned long) as arguments without warnings. Also fix all offending call sites to pass a (void *) rather than an unsigned long. Since virt_to_mfn() is wrapping virt_to_pfn() this function has become polymorphic as well so the usage need to be fixed up. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20230810-virt-to-phys-x86-xen-v1-1-9e966d333e7a@linaro.org Signed-off-by: Juergen Gross <jgross@suse.com>
* iscsi_ibft: Fix finding the iBFT under Xen Dom 0Ross Lagerwall2023-06-261-9/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To facilitate diskless iSCSI boot, the firmware can place a table of configuration details in memory called the iBFT. The presence of this table is not specified, nor is the precise location (and it's not in the E820) so the kernel has to search for a magic marker to find it. When running under Xen, Dom 0 does not have access to the entire host's memory, only certain regions which are identity-mapped which means that the pseudo-physical address in Dom0 == real host physical address. Add the iBFT search bounds as a reserved region which causes it to be identity-mapped in xen_set_identity_and_remap_chunk() which allows Dom0 access to the specific physical memory to correctly search for the iBFT magic marker (and later access the full table). This necessitates moving the call to reserve_ibft_region() somewhat later so that it is called after e820__memory_setup() which is when the Xen identity mapping adjustments are applied. The precise location of the call is not too important so I've put it alongside dmi_setup() which does similar scanning of memory for configuration tables. Finally in the iBFT find code, instead of using isa_bus_to_virt() which doesn't do the right thing under Xen, use early_memremap() like the dmi_setup() code does. The result of these changes is that it is possible to boot a diskless Xen + Dom0 running off an iSCSI disk whereas previously it would fail to find the iBFT and consequently, the iSCSI root disk. Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Juergen Gross <jgross@suse.com> Acked-by: Konrad Rzeszutek Wilk <konrad@darnok.org> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> # for x86 Link: https://lore.kernel.org/r/20230605102840.1521549-1-ross.lagerwall@citrix.com Signed-off-by: Juergen Gross <jgross@suse.com>
* x86/Xen: drop leftover VM-assist usesJan Beulich2023-02-181-4/+0
| | | | | | | | | | | | Both the 4Gb-segments and the PAE-extended-CR3 one are applicable to 32-bit guests only. The PAE-extended-CR3 use, furthermore, was redundant with the PAE_MODE ELF note anyway. Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/215515af-cfb9-3237-03ba-3312e3fa0d34@suse.com Signed-off-by: Juergen Gross <jgross@suse.com>
* x86/xen: Use kstrtobool() instead of strtobool()Christophe JAILLET2022-11-141-1/+2
| | | | | | | | | | | | | | | strtobool() is the same as kstrtobool(). However, the latter is more used within the kernel. In order to remove strtobool() and slightly simplify kstrtox.h, switch to the other function name. While at it, include the corresponding header file (<linux/kstrtox.h>) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/e91af3c8708af38b1c57e0a2d7eb9765dda0e963.1667336095.git.christophe.jaillet@wanadoo.fr Signed-off-by: Juergen Gross <jgross@suse.com>
* x86/xen: simplify sysenter and syscall setupJuergen Gross2022-11-031-17/+6
| | | | | | | | | xen_enable_sysenter() and xen_enable_syscall() can be simplified a lot. While at it, switch to use cpu_feature_enabled() instead of boot_cpu_has(). Signed-off-by: Juergen Gross <jgross@suse.com>
* x86/xen: Rename SYS* entry pointsPeter Zijlstra2022-06-271-3/+3
| | | | | | | | | | | Native SYS{CALL,ENTER} entry points are called entry_SYS{CALL,ENTER}_{64,compat}, make sure the Xen versions are named consistently. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org> Signed-off-by: Borislav Petkov <bp@suse.de>
* x86/xen: Fix kerneldoc warningJiapeng Chong2022-03-101-1/+1
| | | | | | | | | | | | | | Fix the following W=1 kernel warnings: arch/x86/xen/setup.c:725: warning: expecting prototype for machine_specific_memory_setup(). Prototype was for xen_memory_setup() instead. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/20220307062554.8334-1-jiapeng.chong@linux.alibaba.com Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
* Merge tag 'for-linus-5.16b-rc1-tag' of ↵Linus Torvalds2021-11-101-7/+3
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen updates from Juergen Gross: - a series to speed up the boot of Xen PV guests - some cleanups in Xen related code - replacement of license texts with the appropriate SPDX headers and fixing of wrong SPDX headers in Xen header files - a small series making paravirtualized interrupt masking much simpler and at the same time removing complaints of objtool - a fix for Xen ballooning hogging workqueues for too long - enablement of the Xen pciback driver for Arm - some further small fixes/enhancements * tag 'for-linus-5.16b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (22 commits) xen/balloon: fix unused-variable warning xen/balloon: rename alloc/free_xenballooned_pages xen/balloon: add late_initcall_sync() for initial ballooning done x86/xen: remove 32-bit awareness from startup_xen xen: remove highmem remnants xen: allow pv-only hypercalls only with CONFIG_XEN_PV x86/xen: remove 32-bit pv leftovers xen-pciback: allow compiling on other archs than x86 x86/xen: switch initial pvops IRQ functions to dummy ones x86/xen: remove xen_have_vcpu_info_placement flag x86/pvh: add prototype for xen_pvh_init() xen: Fix implicit type conversion xen: fix wrong SPDX headers of Xen related headers xen/pvcalls-back: Remove redundant 'flush_workqueue()' calls x86/xen: Remove redundant irq_enter/exit() invocations xen-pciback: Fix return in pm_ctrl_init() xen/x86: restrict PV Dom0 identity mapping xen/x86: there's no highmem anymore in PV mode xen/x86: adjust handling of the L3 user vsyscall special page table xen/x86: adjust xen_set_fixmap() ...
| * xen/x86: restrict PV Dom0 identity mappingJan Beulich2021-11-021-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When moving away RAM pages, there having been a mapping of those is not a proper indication that instead MMIO should be mapped there. At the point in time this effectively covers the low megabyte only. Mapping of that is, however, the job of init_mem_mapping(). Comparing the two one can also spot that we've been wrongly (or at least inconsistently) using PAGE_KERNEL_IO here. Simply zap any such mappings instead. Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/038b8c02-3621-d66a-63ae-982ccf67ae88@suse.com Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
| * xen/x86: there's no highmem anymore in PV modeJan Beulich2021-11-021-4/+0
| | | | | | | | | | | | | | | | | | | | Considerations for it are a leftover from when 32-bit was still supported. Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/ba6e0779-18f4-ae64-b216-73205b4eec3c@suse.com Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
* | memblock: rename memblock_free to memblock_phys_freeMike Rapoport2021-11-061-3/+3
|/ | | | | | | | | | | | | | | | | | | | | | | Since memblock_free() operates on a physical range, make its name reflect it and rename it to memblock_phys_free(), so it will be a logical counterpart to memblock_phys_alloc(). The callers are updated with the below semantic patch: @@ expression addr; expression size; @@ - memblock_free(addr, size); + memblock_phys_free(addr, size); Link: https://lkml.kernel.org/r/20210930185031.18648-6-rppt@kernel.org Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Juergen Gross <jgross@suse.com> Cc: Shahab Vahedi <Shahab.Vahedi@synopsys.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Revert "xen: fix p2m size in dom0 for disabled memory hotplug case"Roger Pau Monne2021-03-241-2/+14
| | | | | | | | | | | | | | | | | | | | | | | This partially reverts commit 882213990d32 ("xen: fix p2m size in dom0 for disabled memory hotplug case") There's no need to special case XEN_UNPOPULATED_ALLOC anymore in order to correctly size the p2m. The generic memory hotplug option has already been tied together with the Xen hotplug limit, so enabling memory hotplug should already trigger a properly sized p2m on Xen PV. Note that XEN_UNPOPULATED_ALLOC depends on ZONE_DEVICE which pulls in MEMORY_HOTPLUG. Leave the check added to __set_phys_to_machine and the adjusted comment about EXTRA_MEM_RATIO. Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/20210324122424.58685-3-roger.pau@citrix.com [boris: fixed formatting issues] Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
* xen: fix p2m size in dom0 for disabled memory hotplug caseJuergen Gross2021-03-031-22/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 9e2369c06c8a18 ("xen: add helpers to allocate unpopulated memory") foreign mappings are using guest physical addresses allocated via ZONE_DEVICE functionality. This will result in problems for the case of no balloon memory hotplug being configured, as the p2m list will only cover the initial memory size of the domain. Any ZONE_DEVICE allocated address will be outside the p2m range and thus a mapping can't be established with that memory address. Fix that by extending the p2m size for that case. At the same time add a check for a to be created mapping to be within the p2m limits in order to detect errors early. While changing a comment, remove some 32-bit leftovers. This is XSA-369. Fixes: 9e2369c06c8a18 ("xen: add helpers to allocate unpopulated memory") Cc: <stable@vger.kernel.org> # 5.9 Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* x86/xen: remove 32-bit Xen PV guest supportJuergen Gross2020-08-111-35/+1
| | | | | | | | | | | | | Xen is requiring 64-bit machines today and since Xen 4.14 it can be built without 32-bit PV guest support. There is no need to carry the burden of 32-bit PV guest support in the kernel any longer, as new guests can be either HVM or PVH, or they can use a 64 bit kernel. Remove the 32-bit Xen PV support from the kernel. Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* x86/entry: Switch XEN/PV hypercall entry to IDTENTRYThomas Gleixner2020-06-111-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Convert the XEN/PV hypercall to IDTENTRY: - Emit the ASM stub with DECLARE_IDTENTRY - Remove the ASM idtentry in 64-bit - Remove the open coded ASM entry code in 32-bit - Remove the old prototypes The handler stubs need to stay in ASM code as they need corner case handling and adjustment of the stack pointer. Provide a new C function which invokes the entry/exit handling and calls into the XEN handler on the interrupt stack if required. The exit code is slightly different from the regular idtentry_exit() on non-preemptible kernels. If the hypercall is preemptible and need_resched() is set then XEN provides a preempt hypercall scheduling function. Move this functionality into the entry code so it can use the existing idtentry functionality. [ mingo: Build fixes. ] Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Andy Lutomirski <luto@kernel.org> Acked-by: Juergen Gross <jgross@suse.com> Tested-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20200521202118.055270078@linutronix.de
* x86/xen: make xen_pvmmu_arch_setup() staticJason Yan2020-04-081-1/+1
| | | | | | | | | | | | | Fix the following sparse warning: arch/x86/xen/setup.c:998:12: warning: symbol 'xen_pvmmu_arch_setup' was not declared. Should it be static? Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20200408024605.42394-1-yanaijie@huawei.com Signed-off-by: Juergen Gross <jgross@suse.com>
* x86: Use pr_warn instead of pr_warningKefeng Wang2019-10-181-1/+1
| | | | | | | | | | | | | | | | | | As said in commit f2c2cbcc35d4 ("powerpc: Use pr_warn instead of pr_warning"), removing pr_warning so all logging messages use a consistent <prefix>_warn style. Let's do it. Link: http://lkml.kernel.org/r/20191018031850.48498-7-wangkefeng.wang@huawei.com To: linux-kernel@vger.kernel.org Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Robert Richter <rric@kernel.org> Cc: Darren Hart <dvhart@infradead.org> Cc: Andy Shevchenko <andy@infradead.org> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: Petr Mladek <pmladek@suse.com>
* x86/xen: dont add memory above max allowed allocationJuergen Gross2019-02-181-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Don't allow memory to be added above the allowed maximum allocation limit set by Xen. Trying to do so would result in cases like the following: [ 584.559652] ------------[ cut here ]------------ [ 584.564897] WARNING: CPU: 2 PID: 1 at ../arch/x86/xen/multicalls.c:129 xen_alloc_pte+0x1c7/0x390() [ 584.575151] Modules linked in: [ 584.578643] Supported: Yes [ 584.581750] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.4.120-92.70-default #1 [ 584.590000] Hardware name: Cisco Systems Inc UCSC-C460-M4/UCSC-C460-M4, BIOS C460M4.4.0.1b.0.0629181419 06/29/2018 [ 584.601862] 0000000000000000 ffffffff813175a0 0000000000000000 ffffffff8184777c [ 584.610200] ffffffff8107f4e1 ffff880487eb7000 ffff8801862b79c0 ffff88048608d290 [ 584.618537] 0000000000487eb7 ffffea0000000201 ffffffff81009de7 ffffffff81068561 [ 584.626876] Call Trace: [ 584.629699] [<ffffffff81019ad9>] dump_trace+0x59/0x340 [ 584.635645] [<ffffffff81019eaa>] show_stack_log_lvl+0xea/0x170 [ 584.642391] [<ffffffff8101ac51>] show_stack+0x21/0x40 [ 584.648238] [<ffffffff813175a0>] dump_stack+0x5c/0x7c [ 584.654085] [<ffffffff8107f4e1>] warn_slowpath_common+0x81/0xb0 [ 584.660932] [<ffffffff81009de7>] xen_alloc_pte+0x1c7/0x390 [ 584.667289] [<ffffffff810647f0>] pmd_populate_kernel.constprop.6+0x40/0x80 [ 584.675241] [<ffffffff815ecfe8>] phys_pmd_init+0x210/0x255 [ 584.681587] [<ffffffff815ed207>] phys_pud_init+0x1da/0x247 [ 584.687931] [<ffffffff815edb3b>] kernel_physical_mapping_init+0xf5/0x1d4 [ 584.695682] [<ffffffff815e9bdd>] init_memory_mapping+0x18d/0x380 [ 584.702631] [<ffffffff81064699>] arch_add_memory+0x59/0xf0 Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* x86: Fix various typos in commentsIngo Molnar2018-12-031-1/+1
| | | | | | | | | | | | | | Go over arch/x86/ and fix common typos in comments, and a typo in an actual function argument name. No change in functionality intended. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* Revert "xen/balloon: Mark unallocated host memory as UNUSABLE"Igor Druzhinin2018-11-291-2/+4
| | | | | | | | | | | | | | | | | | | | This reverts commit b3cf8528bb21febb650a7ecbf080d0647be40b9f. That commit unintentionally broke Xen balloon memory hotplug with "hotplug_unpopulated" set to 1. As long as "System RAM" resource got assigned under a new "Unusable memory" resource in IO/Mem tree any attempt to online this memory would fail due to general kernel restrictions on having "System RAM" resources as 1st level only. The original issue that commit has tried to workaround fa564ad96366 ("x86/PCI: Enable a 64bit BAR on AMD Family 15h (Models 00-1f, 30-3f, 60-7f)") also got amended by the following 03a551734 ("x86/PCI: Move and shrink AMD 64-bit window to avoid conflict") which made the original fix to Xen ballooning unnecessary. Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* x86/xen: remove unused function xen_auto_xlated_memory_setup()Juergen Gross2018-08-201-31/+0
| | | | | | | xen_auto_xlated_memory_setup() is a leftover from PVH V1. Remove it. Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
* Merge tag 'for-linus-4.15-rc5-tag' of ↵Linus Torvalds2017-12-221-4/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fixes from Juergen Gross: "This contains two fixes for running under Xen: - a fix avoiding resource conflicts between adding mmio areas and memory hotplug - a fix setting NX bits in page table entries copied from Xen when running a PV guest" * tag 'for-linus-4.15-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen/balloon: Mark unallocated host memory as UNUSABLE x86-64/Xen: eliminate W+X mappings
| * xen/balloon: Mark unallocated host memory as UNUSABLEBoris Ostrovsky2017-12-201-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit f5775e0b6116 ("x86/xen: discard RAM regions above the maximum reservation") left host memory not assigned to dom0 as available for memory hotplug. Unfortunately this also meant that those regions could be used by others. Specifically, commit fa564ad96366 ("x86/PCI: Enable a 64bit BAR on AMD Family 15h (Models 00-1f, 30-3f, 60-7f)") may try to map those addresses as MMIO. To prevent this mark unallocated host memory as E820_TYPE_UNUSABLE (thus effectively reverting f5775e0b6116) and keep track of that region as a hostmem resource that can be used for the hotplug. Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Juergen Gross <jgross@suse.com>
* | License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman2017-11-021-0/+1
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* xen: remove tests for pvh mode in pure pv pathsJuergen Gross2017-08-311-4/+1
| | | | | | | | | | Remove the last tests for XENFEAT_auto_translated_physmap in pure PV-domain specific paths. PVH V1 is gone and the feature will always be "false" in PV guests. Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
* x86: xen: remove unnecessary variable in xen_foreach_remap_area()Gustavo A. R. Silva2017-07-031-5/+2
| | | | | | | | | | | | | | | | | Remove unnecessary variable mfn in function xen_foreach_remap_area() and, refactor the code. Variable mfn at line 518:mfn = xen_remap_buf.mfns[i]; is only being used to store a value to be passed as an argument to the xen_update_mem_tables() function. This value can be passed directly, which makes variable mfn unnecessary. Also, value assigned to variable mfn at line 534:mfn = xen_remap_mfn; is never used. Addresses-Coverity-ID: 1260110 Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* x86/boot/e820: Simplify the e820__update_table() interfaceIngo Molnar2017-01-281-5/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The e820__update_table() parameters are pretty complex: arch/x86/include/asm/e820/api.h:extern int e820__update_table(struct e820_entry *biosmap, int max_nr_map, u32 *pnr_map); But 90% of the usage is trivial: arch/x86/kernel/e820.c: if (e820__update_table(e820_table->entries, ARRAY_SIZE(e820_table->entries), &e820_table->nr_entries)) arch/x86/kernel/e820.c: e820__update_table(e820_table->entries, ARRAY_SIZE(e820_table->entries), &e820_table->nr_entries); arch/x86/kernel/e820.c: e820__update_table(e820_table->entries, ARRAY_SIZE(e820_table->entries), &e820_table->nr_entries); arch/x86/kernel/e820.c: if (e820__update_table(e820_table->entries, ARRAY_SIZE(e820_table->entries), &e820_table->nr_entries) < 0) arch/x86/kernel/e820.c: e820__update_table(boot_params.e820_table, ARRAY_SIZE(boot_params.e820_table), &new_nr); arch/x86/kernel/early-quirks.c: e820__update_table(e820_table->entries, ARRAY_SIZE(e820_table->entries), &e820_table->nr_entries); arch/x86/kernel/setup.c: e820__update_table(e820_table->entries, ARRAY_SIZE(e820_table->entries), &e820_table->nr_entries); arch/x86/kernel/setup.c: e820__update_table(e820_table->entries, ARRAY_SIZE(e820_table->entries), &e820_table->nr_entries); arch/x86/platform/efi/efi.c: e820__update_table(e820_table->entries, ARRAY_SIZE(e820_table->entries), &e820_table->nr_entries); arch/x86/xen/setup.c: e820__update_table(xen_e820_table.entries, ARRAY_SIZE(xen_e820_table.entries), arch/x86/xen/setup.c: e820__update_table(e820_table->entries, ARRAY_SIZE(e820_table->entries), &e820_table->nr_entries); arch/x86/xen/setup.c: e820__update_table(xen_e820_table.entries, ARRAY_SIZE(xen_e820_table.entries), as it only uses an exiting struct e820_table's entries array, its size and its current number of entries as input and output arguments. Only one use is non-trivial: arch/x86/kernel/e820.c: e820__update_table(boot_params.e820_table, ARRAY_SIZE(boot_params.e820_table), &new_nr); ... which call updates the E820 table in the zeropage in-situ, and the layout there does not match that of 'struct e820_table' (in particular nr_entries is at a different offset, hardcoded by the boot protocol). Simplify all this by introducing a low level __e820__update_table() API that the zeropage update call can use, and simplifying the main e820__update_table() call signature down to: int e820__update_table(struct e820_table *table); This visibly simplifies all the call sites: arch/x86/include/asm/e820/api.h:extern int e820__update_table(struct e820_table *table); arch/x86/include/asm/e820/types.h: * call to e820__update_table() to remove duplicates. The allowance arch/x86/kernel/e820.c: * The return value from e820__update_table() is zero if it arch/x86/kernel/e820.c:int __init e820__update_table(struct e820_table *table) arch/x86/kernel/e820.c: if (e820__update_table(e820_table)) arch/x86/kernel/e820.c: e820__update_table(e820_table_firmware); arch/x86/kernel/e820.c: e820__update_table(e820_table); arch/x86/kernel/e820.c: e820__update_table(e820_table); arch/x86/kernel/e820.c: if (e820__update_table(e820_table) < 0) arch/x86/kernel/early-quirks.c: e820__update_table(e820_table); arch/x86/kernel/setup.c: e820__update_table(e820_table); arch/x86/kernel/setup.c: e820__update_table(e820_table); arch/x86/platform/efi/efi.c: e820__update_table(e820_table); arch/x86/xen/setup.c: e820__update_table(&xen_e820_table); arch/x86/xen/setup.c: e820__update_table(e820_table); arch/x86/xen/setup.c: e820__update_table(&xen_e820_table); No change in functionality. Cc: Alex Thorlton <athorlton@sgi.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* xen, x86/boot/e820: Simplify Xen's xen_e820_table constructIngo Molnar2017-01-281-37/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Xen guest memory setup code has: static struct e820_entry xen_e820_table[E820_MAX_ENTRIES] __initdata; static u32 xen_e820_table_entries __initdata; ... which is really a 'struct e820_table', open-coded. Convert the Xen code over to use a single struct e820_table, as this will allow the simplification of the e820__update_table() API. No intended change in functionality, but not runtime tested. Cc: Alex Thorlton <athorlton@sgi.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/boot/e820: Clean up the E820 table size define namesIngo Molnar2017-01-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We've got a number of defines related to the E820 table and its size: E820MAP E820NR E820_X_MAX E820MAX The first two denote byte offsets into the zeropage (struct boot_params), and can are not used in the kernel and can be removed. The E820_*_MAX values have an inconsistent structure and it's unclear in any case what they mean. 'X' presuably goes for extended - but it's not very expressive altogether. Change these over to: E820_MAX_ENTRIES_ZEROPAGE E820_MAX_ENTRIES ... which are self-explanatory names. No change in functionality. Cc: Alex Thorlton <athorlton@sgi.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/boot/e820: Prefix the E820_* type names with "E820_TYPE_"Ingo Molnar2017-01-281-11/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So there's a number of constants that start with "E820" but which are not types - these create a confusing mixture when seen together with 'enum e820_type' values: E820MAP E820NR E820_X_MAX E820MAX To better differentiate the 'enum e820_type' values prefix them with E820_TYPE_. No change in functionality. Cc: Alex Thorlton <athorlton@sgi.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/boot/e820: Create coherent API function names for E820 range operationsIngo Molnar2017-01-281-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have these three related functions: extern void e820_add_region(u64 start, u64 size, int type); extern u64 e820_update_range(u64 start, u64 size, unsigned old_type, unsigned new_type); extern u64 e820_remove_range(u64 start, u64 size, unsigned old_type, int checktype); But it's not clear from the naming that they are 3 operations based around the same 'memory range' concept. Rename them to better signal this, and move the prototypes next to each other: extern void e820__range_add (u64 start, u64 size, int type); extern u64 e820__range_update(u64 start, u64 size, unsigned old_type, unsigned new_type); extern u64 e820__range_remove(u64 start, u64 size, unsigned old_type, int checktype); Note that this improved organization of the functions shows another problem that was easy to miss before: sometimes the E820 entry type is 'int', sometimes 'unsigned int' - but this will be fixed in a separate patch. No change in functionality. Cc: Alex Thorlton <athorlton@sgi.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/boot/e820: Rename sanitize_e820_table() to e820__update_table()Ingo Molnar2017-01-281-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | sanitize_e820_table() is a minor misnomer in that it suggests that the E820 table requires sanitizing - which implies that it will only do anything if the E820 table is irregular (not sane). That is wrong, because sanitize_e820_table() also does a very regular sorting of the E820 table, which is a necessity in the basic append-only flow of E820 updates the kernel is allowed to perform to it. So rename it to e820__update_table() to include that purpose as well. This also lines up all the table-update functions into a coherent naming family: int e820__update_table(struct e820_entry *biosmap, int max_nr_map, u32 *pnr_map); void e820__update_table_print(void); void e820__update_table_firmware(void); No change in functionality. Cc: Alex Thorlton <athorlton@sgi.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/boot/e820: Harmonize the 'struct e820_table' fieldsIngo Molnar2017-01-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So the e820_table->map and e820_table->nr_map names are a bit confusing, because it's not clear what a 'map' really means (it could be a bitmap, or some other data structure), nor is it clear what nr_map means (is it a current index, or some other count). Rename the fields from: e820_table->map => e820_table->entries e820_table->nr_map => e820_table->nr_entries which makes it abundantly clear that these are entries of the table, and that the size of the table is ->nr_entries. Propagate the changes to all affected files. Where necessary, adjust local variable names to better reflect the new field names. No change in functionality. Cc: Alex Thorlton <athorlton@sgi.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/boot/e820: Rename everything to e820_tableIngo Molnar2017-01-281-38/+38
| | | | | | | | | | | | | | | | | | | | | | | | | No change in functionality. Cc: Alex Thorlton <athorlton@sgi.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/boot/e820: Rename 'e820_map' variables to 'e820_array'Ingo Molnar2017-01-281-38/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In line with the rename to 'struct e820_array', harmonize the naming of common e820 table variable names as well: e820 => e820_array e820_saved => e820_array_saved e820_map => e820_array initial_e820 => e820_array_init This makes the variable names more consistent and easier to grep for. No change in functionality. Cc: Alex Thorlton <athorlton@sgi.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/boot/e820: Rename the basic e820 data types to 'struct e820_entry' and ↵Ingo Molnar2017-01-281-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 'struct e820_array' The 'e820entry' and 'e820map' names have various annoyances: - the missing underscore departs from the usual kernel style and makes the code look weird, - in the past I kept confusing the 'map' with the 'entry', because a 'map' is ambiguous in that regard, - it's not really clear from the 'e820map' that this is a regular C array. Rename them to 'struct e820_entry' and 'struct e820_array' accordingly. ( Leave the legacy UAPI header alone but do the rename in the bootparam.h and e820/types.h file - outside tools relying on these defines should either adjust their code, or should use the legacy header, or should create their private copies for the definitions. ) No change in functionality. Cc: Alex Thorlton <athorlton@sgi.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* x86/boot/e820: Move asm/e820.h to asm/e820/api.hIngo Molnar2017-01-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In line with asm/e820/types.h, move the e820 API declarations to asm/e820/api.h and update all usage sites. This is just a mechanical, obviously correct move & replace patch, there will be subsequent changes to clean up the code and to make better use of the new header organization. Cc: Alex Thorlton <athorlton@sgi.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
* xen/setup: Don't relocate p2m over existing oneRoss Lagerwall2016-12-221-3/+3
| | | | | | | | | | | | | | When relocating the p2m, take special care not to relocate it so that is overlaps with the current location of the p2m/initrd. This is needed since the full extent of the current location is not marked as a reserved region in the e820. This was seen to happen to a dom0 with a large initial p2m and a small reserved region in the middle of the initial p2m. Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
* xen/x86: Increase xen_e820_map to E820_X_MAX possible entriesAlex Thorlton2016-12-091-3/+3
| | | | | | | | | | | | | | | | | | | | On systems with sufficiently large e820 tables, and several IOAPICs, it is possible for the XENMEM_machine_memory_map callback (and its counterpart, XENMEM_memory_map) to attempt to return an e820 table with more than 128 entries. This callback adds entries to the BIOS-provided e820 table to account for IOAPIC registers, which, on sufficiently large systems, can result in an e820 table that is too large to copy back into xen_e820_map. This change simply increases the size of xen_e820_map to E820_X_MAX to ensure that there is enough room to store the entire e820 map returned from this callback. Signed-off-by: Alex Thorlton <athorlton@sgi.com> Suggested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Juergen Gross <jgross@suse.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Juergen Gross <jgross@suse.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-21 09:56:52 +0000