| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The help text should be indented by at least two spaces after the
'help' separator. This is both good practice and the media_build system
for building media drivers makes this assumption.
I went through all Kconfigs under drivers/media and fixed any bad help
sections. This makes it conform to the common practice and should fix
problems with 'make menuconfig' when using media_build. This is due to
a "WARNING" message that media_build can insert in the Kconfig and that
assumes the help text is indented by at least two spaces. If not, then the
Kconfig becomes invalid and 'make menuconfig' fails.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Thomas Kaiser <linux-dvb@kaiser-linux.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
As reported by Randy:
> flexcop-pci.c:(.text+0x19af63): undefined reference to `flexcop_device_exit'
> flexcop-pci.c:(.text+0x19af77): undefined reference to `flexcop_device_kfree'
> flexcop-pci.c:(.text+0x19b10f): undefined reference to `flexcop_pass_dmx_packets'
> flexcop-pci.c:(.text+0x19b182): undefined reference to `flexcop_pass_dmx_data'
> flexcop-pci.c:(.text+0x19b1ae): undefined reference to `flexcop_pass_dmx_data'
> flexcop-pci.c:(.text+0x19b1f8): undefined reference to `flexcop_device_kmalloc'
> flexcop-pci.c:(.text+0x19b256): undefined reference to `flexcop_i2c_request'
> flexcop-pci.c:(.text+0x19b261): undefined reference to `flexcop_eeprom_check_mac_addr'
> flexcop-pci.c:(.text+0x19b2c6): undefined reference to `flexcop_device_initialize'
> flexcop-pci.c:(.text+0x19b332): undefined reference to `flexcop_sram_set_dest'
> flexcop-pci.c:(.text+0x19b348): undefined reference to `flexcop_sram_set_dest'
> flexcop-pci.c:(.text+0x19b3f8): undefined reference to `flexcop_device_exit'
> flexcop-pci.c:(.text+0x19b408): undefined reference to `flexcop_device_kfree'
> flexcop-pci.c:(.text+0x19b4a2): undefined reference to `flexcop_pid_feed_control'
> flexcop-pci.c:(.text+0x19b4d7): undefined reference to `flexcop_pid_feed_control'
>
> since it is possible to enable DVB_B2C2_FLEXCOP_PCI
> when CONFIG_I2C is not enabled, but then DVB_B2C2_FLEXCOP
> is not enabled because I2C is not enabled.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
| |
|
|
|
|
|
| |
Instead of showing the option to show debug at the end, show
it after each driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
|
b2c2 is, in fact, 2 drivers: one for PCI and one for USB, plus
a common bus-independent code. Break it accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
