summaryrefslogtreecommitdiffstats
path: root/include/net/switchdev.h
Commit message (Collapse)AuthorAgeFilesLines
* net: bridge: switchdev: Skip MDB replays of deferred events on offloadTobias Waldekranz2024-02-161-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Before this change, generation of the list of MDB events to replay would race against the creation of new group memberships, either from the IGMP/MLD snooping logic or from user configuration. While new memberships are immediately visible to walkers of br->mdb_list, the notification of their existence to switchdev event subscribers is deferred until a later point in time. So if a replay list was generated during a time that overlapped with such a window, it would also contain a replay of the not-yet-delivered event. The driver would thus receive two copies of what the bridge internally considered to be one single event. On destruction of the bridge, only a single membership deletion event was therefore sent. As a consequence of this, drivers which reference count memberships (at least DSA), would be left with orphan groups in their hardware database when the bridge was destroyed. This is only an issue when replaying additions. While deletion events may still be pending on the deferred queue, they will already have been removed from br->mdb_list, so no duplicates can be generated in that scenario. To a user this meant that old group memberships, from a bridge in which a port was previously attached, could be reanimated (in hardware) when the port joined a new bridge, without the new bridge's knowledge. For example, on an mv88e6xxx system, create a snooping bridge and immediately add a port to it: root@infix-06-0b-00:~$ ip link add dev br0 up type bridge mcast_snooping 1 && \ > ip link set dev x3 up master br0 And then destroy the bridge: root@infix-06-0b-00:~$ ip link del dev br0 root@infix-06-0b-00:~$ mvls atu ADDRESS FID STATE Q F 0 1 2 3 4 5 6 7 8 9 a DEV:0 Marvell 88E6393X 33:33:00:00:00:6a 1 static - - 0 . . . . . . . . . . 33:33:ff:87:e4:3f 1 static - - 0 . . . . . . . . . . ff:ff:ff:ff:ff:ff 1 static - - 0 1 2 3 4 5 6 7 8 9 a root@infix-06-0b-00:~$ The two IPv6 groups remain in the hardware database because the port (x3) is notified of the host's membership twice: once via the original event and once via a replay. Since only a single delete notification is sent, the count remains at 1 when the bridge is destroyed. Then add the same port (or another port belonging to the same hardware domain) to a new bridge, this time with snooping disabled: root@infix-06-0b-00:~$ ip link add dev br1 up type bridge mcast_snooping 0 && \ > ip link set dev x3 up master br1 All multicast, including the two IPv6 groups from br0, should now be flooded, according to the policy of br1. But instead the old memberships are still active in the hardware database, causing the switch to only forward traffic to those groups towards the CPU (port 0). Eliminate the race in two steps: 1. Grab the write-side lock of the MDB while generating the replay list. This prevents new memberships from showing up while we are generating the replay list. But it leaves the scenario in which a deferred event was already generated, but not delivered, before we grabbed the lock. Therefore: 2. Make sure that no deferred version of a replay event is already enqueued to the switchdev deferred queue, before adding it to the replay list, when replaying additions. Fixes: 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries") Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: switchdev: Remove unused declaration switchdev_port_fwd_mark_set()Yue Haibing2023-08-091-4/+0
| | | | | | | | | | | Commit 6bc506b4fb06 ("bridge: switchdev: Add forward mark support for stacked devices") removed the implementation but leave declaration. Signed-off-by: Yue Haibing <yuehaibing@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Petr Machata <petrm@nvidia.com> Link: https://lore.kernel.org/r/20230808145955.2176-1-yuehaibing@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: switchdev: Remove unused typedef switchdev_obj_dump_cb_t()Yue Haibing2023-08-021-2/+0
| | | | | | | | | | Commit 29ab586c3d83 ("net: switchdev: Remove bridge bypass support from switchdev") leave this unused. Signed-off-by: Yue Haibing <yuehaibing@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230801144209.27512-1-yuehaibing@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: switchdev: Add a helper to replay objects on a bridge portPetr Machata2023-07-211-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | When a front panel joins a bridge via another netdevice (typically a LAG), the driver needs to learn about the objects configured on the bridge port. When the bridge port is offloaded by the driver for the first time, this can be achieved by passing a notifier to switchdev_bridge_port_offload(). The notifier is then invoked for the individual objects (such as VLANs) configured on the bridge, and can look for the interesting ones. Calling switchdev_bridge_port_offload() when the second port joins the bridge lower is unnecessary, but the replay is still needed. To that end, add a new function, switchdev_bridge_port_replay(), which does only the replay part of the _offload() function in exactly the same way as that function. Cc: Jiri Pirko <jiri@resnulli.us> Cc: Ivan Vecera <ivecera@redhat.com> Cc: Roopa Prabhu <roopa@nvidia.com> Cc: Nikolay Aleksandrov <razor@blackwall.org> Cc: bridge@lists.linux-foundation.org Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: switchdev: Allow device drivers to install locked FDB entriesHans J. Schultz2022-11-091-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the bridge is offloaded to hardware, FDB entries are learned and aged-out by the hardware. Some device drivers synchronize the hardware and software FDBs by generating switchdev events towards the bridge. When a port is locked, the hardware must not learn autonomously, as otherwise any host will blindly gain authorization. Instead, the hardware should generate events regarding hosts that are trying to gain authorization and their MAC addresses should be notified by the device driver as locked FDB entries towards the bridge driver. Allow device drivers to notify the bridge driver about such entries by extending the 'switchdev_notifier_fdb_info' structure with the 'locked' bit. The bit can only be set by device drivers and not by the bridge driver. Prevent a locked entry from being installed if MAB is not enabled on the bridge port. If an entry already exists in the bridge driver, reject the locked entry if the current entry does not have the "locked" flag set or if it points to a different port. The same semantics are implemented in the software data path. Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: switchdev: add reminder near struct switchdev_notifier_fdb_infoVladimir Oltean2022-06-291-0/+3
| | | | | | | | | | | | | | | | | | | | | br_switchdev_fdb_notify() creates an on-stack FDB info variable, and initializes it member by member. As such, newly added fields which are not initialized by br_switchdev_fdb_notify() will contain junk bytes from the stack. Other uses of struct switchdev_notifier_fdb_info have a struct initializer which should put zeroes in the uninitialized fields. Add a reminder above the structure for future developers. Recently discussed during review. Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220524152144.40527-2-schultz.hans+netdev@gmail.com/#24877698 Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220524152144.40527-3-schultz.hans+netdev@gmail.com/#24912269 Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20220628100831.2899434-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: bridge: mst: Notify switchdev drivers of MST state changesTobias Waldekranz2022-03-171-0/+7
| | | | | | | | | | Generate a switchdev notification whenever an MST state changes. This notification is keyed by the VLANs MSTI rather than the VID, since multiple VLANs may share the same MST instance. Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: bridge: mst: Notify switchdev drivers of VLAN MSTI migrationsTobias Waldekranz2022-03-171-0/+7
| | | | | | | | | Whenever a VLAN moves to a new MSTI, send a switchdev notification so that switchdevs can track a bridge's VID to MSTI mappings. Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: bridge: mst: Notify switchdev drivers of MST mode changesTobias Waldekranz2022-03-171-0/+2
| | | | | | | | | | Trigger a switchdev event whenever the bridge's MST mode is enabled/disabled. This allows constituent ports to either perform any required hardware config, or refuse the change if it not supported. Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: switchdev: remove lag_mod_cb from switchdev_handle_fdb_event_to_deviceVladimir Oltean2022-02-241-8/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the switchdev_handle_fdb_event_to_device() event replication helper was created, my original thought was that FDB events on LAG interfaces should most likely be special-cased, not just replicated towards all switchdev ports beneath that LAG. So this replication helper currently does not recurse through switchdev lower interfaces of LAG bridge ports, but rather calls the lag_mod_cb() if that was provided. No switchdev driver uses this helper for FDB events on LAG interfaces yet, so that was an assumption which was yet to be tested. It is certainly usable for that purpose, as my RFC series shows: https://patchwork.kernel.org/project/netdevbpf/cover/20220210125201.2859463-1-vladimir.oltean@nxp.com/ however this approach is slightly convoluted because: - the switchdev driver gets a "dev" that isn't its own net device, but rather the LAG net device. It must call switchdev_lower_dev_find(dev) in order to get a handle of any of its own net devices (the ones that pass check_cb). - in order for FDB entries on LAG ports to be correctly refcounted per the number of switchdev ports beneath that LAG, we haven't escaped the need to iterate through the LAG's lower interfaces. Except that is now the responsibility of the switchdev driver, because the replication helper just stopped half-way. So, even though yes, FDB events on LAG bridge ports must be special-cased, in the end it's simpler to let switchdev_handle_fdb_* just iterate through the LAG port's switchdev lowers, and let the switchdev driver figure out that those physical ports are under a LAG. The switchdev_handle_fdb_event_to_device() helper takes a "foreign_dev_check" callback so it can figure out whether @dev can autonomously forward to @foreign_dev. DSA fills this method properly: if the LAG is offloaded by another port in the same tree as @dev, then it isn't foreign. If it is a software LAG, it is foreign - forwarding happens in software. Whether an interface is foreign or not decides whether the replication helper will go through the LAG's switchdev lowers or not. Since the lan966x doesn't properly fill this out, FDB events on software LAG uppers will get called. By changing lan966x_foreign_dev_check(), we can suppress them. Whereas DSA will now start receiving FDB events for its offloaded LAG uppers, so we need to return -EOPNOTSUPP, since we currently don't do the right thing for them. Cc: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: switchdev: introduce switchdev_handle_port_obj_{add,del} for foreign ↵Vladimir Oltean2022-02-161-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | interfaces The switchdev_handle_port_obj_add() helper is good for replicating a port object on the lower interfaces of @dev, if that object was emitted on a bridge, or on a bridge port that is a LAG. However, drivers that use this helper limit themselves to a box from which they can no longer intercept port objects notified on neighbor ports ("foreign interfaces"). One such driver is DSA, where software bridging with foreign interfaces such as standalone NICs or Wi-Fi APs is an important use case. There, a VLAN installed on a neighbor bridge port roughly corresponds to a forwarding VLAN installed on the DSA switch's CPU port. To support this use case while also making use of the benefits of the switchdev_handle_* replication helper for port objects, introduce a new variant of these functions that crawls through the neighbor ports of @dev, in search of potentially compatible switchdev ports that are interested in the event. The strategy is identical to switchdev_handle_fdb_event_to_device(): if @dev wasn't a switchdev interface, then go one step upper, and recursively call this function on the bridge that this port belongs to. At the next recursion step, __switchdev_handle_port_obj_add() will iterate through the bridge's lower interfaces. Among those, some will be switchdev interfaces, and one will be the original @dev that we came from. To prevent infinite recursion, we must suppress reentry into the original @dev, and just call the @add_cb for the switchdev_interfaces. It looks like this: br0 / | \ / | \ / | \ swp0 swp1 eth0 1. __switchdev_handle_port_obj_add(eth0) -> check_cb(eth0) returns false -> eth0 has no lower interfaces -> eth0's bridge is br0 -> switchdev_lower_dev_find(br0, check_cb, foreign_dev_check_cb)) finds br0 2. __switchdev_handle_port_obj_add(br0) -> check_cb(br0) returns false -> netdev_for_each_lower_dev -> check_cb(swp0) returns true, so we don't skip this interface 3. __switchdev_handle_port_obj_add(swp0) -> check_cb(swp0) returns true, so we call add_cb(swp0) (back to netdev_for_each_lower_dev from 2) -> check_cb(swp1) returns true, so we don't skip this interface 4. __switchdev_handle_port_obj_add(swp1) -> check_cb(swp1) returns true, so we call add_cb(swp1) (back to netdev_for_each_lower_dev from 2) -> check_cb(eth0) returns false, so we skip this interface to avoid infinite recursion Note: eth0 could have been a LAG, and we don't want to suppress the recursion through its lowers if those exist, so when check_cb() returns false, we still call switchdev_lower_dev_find() to estimate whether there's anything worth a recursion beneath that LAG. Using check_cb() and foreign_dev_check_cb(), switchdev_lower_dev_find() not only figures out whether the lowers of the LAG are switchdev, but also whether they actively offload the LAG or not (whether the LAG is "foreign" to the switchdev interface or not). The port_obj_info->orig_dev is preserved across recursive calls, so switchdev drivers still know on which device was this notification originally emitted. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: switchdev: differentiate new VLANs from changed onesVladimir Oltean2022-02-161-0/+7
| | | | | | | | | | | | | | | | | | | br_switchdev_port_vlan_add() currently emits a SWITCHDEV_PORT_OBJ_ADD event with a SWITCHDEV_OBJ_ID_PORT_VLAN for 2 distinct cases: - a struct net_bridge_vlan got created - an existing struct net_bridge_vlan was modified This makes it impossible for switchdev drivers to properly balance PORT_OBJ_ADD with PORT_OBJ_DEL events, so if we want to allow that to happen, we must provide a way for drivers to distinguish between a VLAN with changed flags and a new one. Annotate struct switchdev_obj_port_vlan with a "bool changed" that distinguishes the 2 cases above. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: switchdev: merge switchdev_handle_fdb_{add,del}_to_deviceVladimir Oltean2021-10-271-38/+10
| | | | | | | | | | | | | | | | | | | To reduce code churn, the same patch makes multiple changes, since they all touch the same lines: 1. The implementations for these two are identical, just with different function pointers. Reduce duplications and name the function pointers "mod_cb" instead of "add_cb" and "del_cb". Pass the event as argument. 2. Drop the "const" attribute from "orig_dev". If the driver needs to check whether orig_dev belongs to itself and then call_switchdev_notifiers(orig_dev, SWITCHDEV_FDB_OFFLOADED), it can't, because call_switchdev_notifiers takes a non-const struct net_device *. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: make switchdev_bridge_port_{,unoffload} loosely coupled with the bridgeVladimir Oltean2021-08-041-0/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With the introduction of explicit offloading API in switchdev in commit 2f5dc00f7a3e ("net: bridge: switchdev: let drivers inform which bridge ports are offloaded"), we started having Ethernet switch drivers calling directly into a function exported by net/bridge/br_switchdev.c, which is a function exported by the bridge driver. This means that drivers that did not have an explicit dependency on the bridge before, like cpsw and am65-cpsw, now do - otherwise it is not possible to call a symbol exported by a driver that can be built as module unless you are a module too. There was an attempt to solve the dependency issue in the form of commit b0e81817629a ("net: build all switchdev drivers as modules when the bridge is a module"). Grygorii Strashko, however, says about it: | In my opinion, the problem is a bit bigger here than just fixing the | build :( | | In case, of ^cpsw the switchdev mode is kinda optional and in many | cases (especially for testing purposes, NFS) the multi-mac mode is | still preferable mode. | | There were no such tight dependency between switchdev drivers and | bridge core before and switchdev serviced as independent, notification | based layer between them, so ^cpsw still can be "Y" and bridge can be | "M". Now for mostly every kernel build configuration the CONFIG_BRIDGE | will need to be set as "Y", or we will have to update drivers to | support build with BRIDGE=n and maintain separate builds for | networking vs non-networking testing. But is this enough? Wouldn't | it cause 'chain reaction' required to add more and more "Y" options | (like CONFIG_VLAN_8021Q)? | | PS. Just to be sure we on the same page - ARM builds will be forced | (with this patch) to have CONFIG_TI_CPSW_SWITCHDEV=m and so all our | automation testing will just fail with omap2plus_defconfig. In the light of this, it would be desirable for some configurations to avoid dependencies between switchdev drivers and the bridge, and have the switchdev mode as completely optional within the driver. Arnd Bergmann also tried to write a patch which better expressed the build time dependency for Ethernet switch drivers where the switchdev support is optional, like cpsw/am65-cpsw, and this made the drivers follow the bridge (compile as module if the bridge is a module) only if the optional switchdev support in the driver was enabled in the first place: https://patchwork.kernel.org/project/netdevbpf/patch/20210802144813.1152762-1-arnd@kernel.org/ but this still did not solve the fact that cpsw and am65-cpsw now must be built as modules when the bridge is a module - it just expressed correctly that optional dependency. But the new behavior is an apparent regression from Grygorii's perspective. So to support the use case where the Ethernet driver is built-in, NET_SWITCHDEV (a bool option) is enabled, and the bridge is a module, we need a framework that can handle the possible absence of the bridge from the running system, i.e. runtime bloatware as opposed to build-time bloatware. Luckily we already have this framework, since switchdev has been using it extensively. Events from the bridge side are transmitted to the driver side using notifier chains - this was originally done so that unrelated drivers could snoop for events emitted by the bridge towards ports that are implemented by other drivers (think of a switch driver with LAG offload that listens for switchdev events on a bonding/team interface that it offloads). There are also events which are transmitted from the driver side to the bridge side, which again are modeled using notifiers. SWITCHDEV_FDB_ADD_TO_BRIDGE is an example of this, and deals with notifying the bridge that a MAC address has been dynamically learned. So there is a precedent we can use for modeling the new framework. The difference compared to SWITCHDEV_FDB_ADD_TO_BRIDGE is that the work that the bridge needs to do when a port becomes offloaded is blocking in its nature: replay VLANs, MDBs etc. The calling context is indeed blocking (we are under rtnl_mutex), but the existing switchdev notification chain that the bridge is subscribed to is only the atomic one. So we need to subscribe the bridge to the blocking switchdev notification chain too. This patch: - keeps the driver-side perception of the switchdev_bridge_port_{,un}offload unchanged - moves the implementation of switchdev_bridge_port_{,un}offload from the bridge module into the switchdev module. - makes everybody that is subscribed to the switchdev blocking notifier chain "hear" offload & unoffload events - makes the bridge driver subscribe and handle those events - moves the bridge driver's handling of those events into 2 new functions called br_switchdev_port_{,un}offload. These functions contain in fact the core of the logic that was previously in switchdev_bridge_port_{,un}offload, just that now we go through an extra indirection layer to reach them. Unlike all the other switchdev notification structures, the structure used to carry the bridge port information, struct switchdev_notifier_brport_info, does not contain a "bool handled". This is because in the current usage pattern, we always know that a switchdev bridge port offloading event will be handled by the bridge, because the switchdev_bridge_port_offload() call was initiated by a NETDEV_CHANGEUPPER event in the first place, where info->upper_dev is a bridge. So if the bridge wasn't loaded, then the CHANGEUPPER event couldn't have happened. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: switchdev: remove stray semicolon in switchdev_handle_fdb_del_to_device ↵Vladimir Oltean2021-07-211-1/+1
| | | | | | | | | | | | | | | shim With the semicolon at the end, the compiler sees the shim function as a declaration and not as a definition, and warns: 'switchdev_handle_fdb_del_to_device' declared 'static' but never defined Reported-by: kernel test robot <lkp@intel.com> Fixes: 8ca07176ab00 ("net: switchdev: introduce a fanout helper for SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: switchdev: introduce a fanout helper for SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICEVladimir Oltean2021-07-201-0/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently DSA has an issue with FDB entries pointing towards the bridge in the presence of br_fdb_replay() being called at port join and leave time. In particular, each bridge port will ask for a replay for the FDB entries pointing towards the bridge when it joins, and for another replay when it leaves. This means that for example, a bridge with 4 switch ports will notify DSA 4 times of the bridge MAC address. But if the MAC address of the bridge changes during the normal runtime of the system, the bridge notifies switchdev [ once ] of the deletion of the old MAC address as a local FDB towards the bridge, and of the insertion [ again once ] of the new MAC address as a local FDB. This is a problem, because DSA keeps the old MAC address as a host FDB entry with refcount 4 (4 ports asked for it using br_fdb_replay). So the old MAC address will not be deleted. Additionally, the new MAC address will only be installed with refcount 1, and when the first switch port leaves the bridge (leaving 3 others as still members), it will delete with it the new MAC address of the bridge from the local FDB entries kept by DSA (because the br_fdb_replay call on deletion will bring the entry's refcount from 1 to 0). So the problem, really, is that the number of br_fdb_replay() calls is not matched with the refcount that a host FDB is offloaded to DSA during normal runtime. An elegant way to solve the problem would be to make the switchdev notification emitted by br_fdb_change_mac_address() result in a host FDB kept by DSA which has a refcount exactly equal to the number of ports under that bridge. Then, no matter how many DSA ports join or leave that bridge, the host FDB entry will always be deleted when there are exactly zero remaining DSA switch ports members of the bridge. To implement the proposed solution, we remember that the switchdev objects and port attributes have some helpers provided by switchdev, which can be optionally called by drivers: switchdev_handle_port_obj_{add,del} and switchdev_handle_port_attr_set. These helpers: - fan out a switchdev object/attribute emitted for the bridge towards all the lower interfaces that pass the check_cb(). - fan out a switchdev object/attribute emitted for a bridge port that is a LAG towards all the lower interfaces that pass the check_cb(). In other words, this is the model we need for the FDB events too: something that will keep an FDB entry emitted towards a physical port as it is, but translate an FDB entry emitted towards the bridge into N FDB entries, one per physical port. Of course, there are many differences between fanning out a switchdev object (VLAN) on 3 lower interfaces of a LAG and fanning out an FDB entry on 3 lower interfaces of a LAG. Intuitively, an FDB entry towards a LAG should be treated specially, because FDB entries are unicast, we can't just install the same address towards 3 destinations. It is imaginable that drivers might want to treat this case specifically, so create some methods for this case and do not recurse into the LAG lower ports, just the bridge ports. DSA also listens for FDB entries on "foreign" interfaces, aka interfaces bridged with us which are not part of our hardware domain: think an Ethernet switch bridged with a Wi-Fi AP. For those addresses, DSA installs host FDB entries. However, there we have the same problem (those host FDB entries are installed with a refcount of only 1) and an even bigger one which we did not have with FDB entries towards the bridge: br_fdb_replay() is currently not called for FDB entries on foreign interfaces, just for the physical port and for the bridge itself. So when DSA sniffs an address learned by the software bridge towards a foreign interface like an e1000 port, and then that e1000 leaves the bridge, DSA remains with the dangling host FDB address. That will be fixed separately by replaying all FDB entries and not just the ones towards the port and the bridge. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: switchdev: introduce helper for checking dynamically learned FDB entriesVladimir Oltean2021-07-201-0/+6
| | | | | | | | | | It is a bit difficult to understand what DSA checks when it tries to avoid installing dynamically learned addresses on foreign interfaces as local host addresses, so create a generic switchdev helper that can be reused and is generally more readable. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: switchdev: add a context void pointer to struct switchdev_notifier_infoVladimir Oltean2021-06-281-6/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | In the case where the driver asks for a replay of a certain type of event (port object or attribute) for a bridge port that is a LAG, it may do so because this port has just joined the LAG. But there might already be other switchdev ports in that LAG, and it is preferable that those preexisting switchdev ports do not act upon the replayed event. The solution is to add a context to switchdev events, which is NULL most of the time (when the bridge layer initiates the call) but which can be set to a value controlled by the switchdev driver when a replay is requested. The driver can then check the context to figure out if all ports within the LAG should act upon the switchdev event, or just the ones that match the context. We have to modify all switchdev_handle_* helper functions as well as the prototypes in the drivers that use these helpers too, because these helpers hide the underlying struct switchdev_notifier_info from us and there is no way to retrieve the context otherwise. The context structure will be populated and used in later patches. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: switchdev: include local flag in FDB notificationsVladimir Oltean2021-04-161-0/+1
| | | | | | | | | | | | | | | | | | | | | As explained in bugfix commit 6ab4c3117aec ("net: bridge: don't notify switchdev for local FDB addresses") as well as in this discussion: https://lore.kernel.org/netdev/20210117193009.io3nungdwuzmo5f7@skbuf/ the switchdev notifiers for FDB entries managed to have a zero-day bug, which was that drivers would not know what to do with local FDB entries, because they were not told that they are local. The bug fix was to simply not notify them of those addresses. Let us now add the 'is_local' bit to bridge FDB entries, and make all drivers ignore these entries by their own choice. Co-developed-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add helper to replay port and host-joined mdb entriesVladimir Oltean2021-03-231-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I have a system with DSA ports, and udhcpcd is configured to bring interfaces up as soon as they are created. I create a bridge as follows: ip link add br0 type bridge As soon as I create the bridge and udhcpcd brings it up, I also have avahi which automatically starts sending IPv6 packets to advertise some local services, and because of that, the br0 bridge joins the following IPv6 groups due to the code path detailed below: 33:33:ff:6d:c1:9c vid 0 33:33:00:00:00:6a vid 0 33:33:00:00:00:fb vid 0 br_dev_xmit -> br_multicast_rcv -> br_ip6_multicast_add_group -> __br_multicast_add_group -> br_multicast_host_join -> br_mdb_notify This is all fine, but inside br_mdb_notify we have br_mdb_switchdev_host hooked up, and switchdev will attempt to offload the host joined groups to an empty list of ports. Of course nobody offloads them. Then when we add a port to br0: ip link set swp0 master br0 the bridge doesn't replay the host-joined MDB entries from br_add_if, and eventually the host joined addresses expire, and a switchdev notification for deleting it is emitted, but surprise, the original addition was already completely missed. The strategy to address this problem is to replay the MDB entries (both the port ones and the host joined ones) when the new port joins the bridge, similar to what vxlan_fdb_replay does (in that case, its FDB can be populated and only then attached to a bridge that you offload). However there are 2 possibilities: the addresses can be 'pushed' by the bridge into the port, or the port can 'pull' them from the bridge. Considering that in the general case, the new port can be really late to the party, and there may have been many other switchdev ports that already received the initial notification, we would like to avoid delivering duplicate events to them, since they might misbehave. And currently, the bridge calls the entire switchdev notifier chain, whereas for replaying it should just call the notifier block of the new guy. But the bridge doesn't know what is the new guy's notifier block, it just knows where the switchdev notifier chain is. So for simplification, we make this a driver-initiated pull for now, and the notifier block is passed as an argument. To emulate the calling context for mdb objects (deferred and put on the blocking notifier chain), we must iterate under RCU protection through the bridge's mdb entries, queue them, and only call them once we're out of the RCU read-side critical section. There was some opportunity for reuse between br_mdb_switchdev_host_port, br_mdb_notify and the newly added br_mdb_queue_one in how the switchdev mdb object is created, so a helper was created. Suggested-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* switchdev: mrp: Extend ring_role_mrp and in_role_mrpHoratiu Vultur2021-02-161-0/+2
| | | | | | | | | | | | | | | | | Add the member sw_backup to the structures switchdev_obj_ring_role_mrp and switchdev_obj_in_role_mrp. In this way the SW can call the driver in 2 ways, once when sw_backup is set to false, meaning that the driver should implement this completely in HW. And if that is not supported the SW will call again but with sw_backup set to true, meaning that the HW should help or allow the SW to run the protocol. For example when role is MRM, if the HW can't detect when it stops receiving MRP Test frames but it can trap these frames to CPU, then it needs to return -EOPNOTSUPP when sw_backup is false and return 0 when sw_backup is true. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* switchdev: mrp: Remove CONFIG_BRIDGE_MRPHoratiu Vultur2021-02-161-10/+0
| | | | | | | | | Remove #IS_ENABLED(CONFIG_BRIDGE_MRP) from switchdev.h. This will simplify the code implements MRP callbacks and will be similar with the vlan filtering. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: fix switchdev_port_attr_set stub when CONFIG_SWITCHDEV=nVladimir Oltean2021-02-151-1/+2
| | | | | | | | | | | The switchdev_port_attr_set function prototype was updated only for the case where CONFIG_SWITCHDEV=y|m, leaving a prototype mismatch with the stub definition for the disabled case. This results in a build error, so update that function too. Fixes: dcbdf1350e33 ("net: bridge: propagate extack through switchdev_port_attr_set") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: propagate extack through switchdev_port_attr_setVladimir Oltean2021-02-141-1/+2
| | | | | | | | | | The benefit is the ability to propagate errors from switchdev drivers for the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING and SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL attributes. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: switchdev: pass flags and mask to both {PRE_,}BRIDGE_FLAGS attributesVladimir Oltean2021-02-121-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | This switchdev attribute offers a counterproductive API for a driver writer, because although br_switchdev_set_port_flag gets passed a "flags" and a "mask", those are passed piecemeal to the driver, so while the PRE_BRIDGE_FLAGS listener knows what changed because it has the "mask", the BRIDGE_FLAGS listener doesn't, because it only has the final value. But certain drivers can offload only certain combinations of settings, like for example they cannot change unicast flooding independently of multicast flooding - they must be both on or both off. The way the information is passed to switchdev makes drivers not expressive enough, and unable to reject this request ahead of time, in the PRE_BRIDGE_FLAGS notifier, so they are forced to reject it during the deferred BRIDGE_FLAGS attribute, where the rejection is currently ignored. This patch also changes drivers to make use of the "mask" field for edge detection when possible. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: switchdev: propagate extack to port attributesVladimir Oltean2021-02-121-2/+4
| | | | | | | | | | | | When a struct switchdev_attr is notified through switchdev, there is no way to report informational messages, unlike for struct switchdev_obj. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Nikolay Aleksandrov <nikolay@nvidia.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2021-02-101-2/+0
|\
| * switchdev: mrp: Remove SWITCHDEV_ATTR_ID_MRP_PORT_STATHoratiu Vultur2021-02-081-2/+0
| | | | | | | | | | | | | | | | | | | | Now that MRP started to use also SWITCHDEV_ATTR_ID_PORT_STP_STATE to notify HW, then SWITCHDEV_ATTR_ID_MRP_PORT_STAT is not used anywhere else, therefore we can remove it. Fixes: c284b545900830 ("switchdev: mrp: Extend switchdev API to offload MRP") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: switchdev: delete the transaction objectVladimir Oltean2021-01-111-14/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | Now that all users of struct switchdev_trans have been modified to do without it, we can remove this structure and the two helpers to determine the phase. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: switchdev: remove the transaction structure from port attributesVladimir Oltean2021-01-111-5/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the introduction of the switchdev API, port attributes were transmitted to drivers for offloading using a two-step transactional model, with a prepare phase that was supposed to catch all errors, and a commit phase that was supposed to never fail. Some classes of failures can never be avoided, like hardware access, or memory allocation. In the latter case, merely attempting to move the memory allocation to the preparation phase makes it impossible to avoid memory leaks, since commit 91cf8eceffc1 ("switchdev: Remove unused transaction item queue") which has removed the unused mechanism of passing on the allocated memory between one phase and another. It is time we admit that separating the preparation from the commit phase is something that is best left for the driver to decide, and not something that should be baked into the API, especially since there are no switchdev callers that depend on this. This patch removes the struct switchdev_trans member from switchdev port attribute notifier structures, and converts drivers to not look at this member. In part, this patch contains a revert of my previous commit 2e554a7a5d8a ("net: dsa: propagate switchdev vlan_filtering prepare phase to drivers"). For the most part, the conversion was trivial except for: - Rocker's world implementation based on Broadcom OF-DPA had an odd implementation of ofdpa_port_attr_bridge_flags_set. The conversion was done mechanically, by pasting the implementation twice, then only keeping the code that would get executed during prepare phase on top, then only keeping the code that gets executed during the commit phase on bottom, then simplifying the resulting code until this was obtained. - DSA's offloading of STP state, bridge flags, VLAN filtering and multicast router could be converted right away. But the ageing time could not, so a shim was introduced and this was left for a further commit. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: switchdev: remove the transaction structure from port object notifiersVladimir Oltean2021-01-111-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the introduction of the switchdev API, port objects were transmitted to drivers for offloading using a two-step transactional model, with a prepare phase that was supposed to catch all errors, and a commit phase that was supposed to never fail. Some classes of failures can never be avoided, like hardware access, or memory allocation. In the latter case, merely attempting to move the memory allocation to the preparation phase makes it impossible to avoid memory leaks, since commit 91cf8eceffc1 ("switchdev: Remove unused transaction item queue") which has removed the unused mechanism of passing on the allocated memory between one phase and another. It is time we admit that separating the preparation from the commit phase is something that is best left for the driver to decide, and not something that should be baked into the API, especially since there are no switchdev callers that depend on this. This patch removes the struct switchdev_trans member from switchdev port object notifier structures, and converts drivers to not look at this member. Where driver conversion is trivial (like in the case of the Marvell Prestera driver, NXP DPAA2 switch, TI CPSW, and Rocker drivers), it is done in this patch. Where driver conversion needs more attention (DSA, Mellanox Spectrum), the conversion is left for subsequent patches and here we only fake the prepare/commit phases at a lower level, just not in the switchdev notifier itself. Where the code has a natural structure that is best left alone as a preparation and a commit phase (as in the case of the Ocelot switch), that structure is left in place, just made to not depend upon the switchdev transactional model. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: switchdev: remove vid_begin -> vid_end range from VLAN objectsVladimir Oltean2021-01-111-2/+1
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The call path of a switchdev VLAN addition to the bridge looks something like this today: nbp_vlan_init | __br_vlan_set_default_pvid | | | | | br_afspec | | | | | | | v | | | br_process_vlan_info | | | | | | | v | | | br_vlan_info | | | / \ / | | / \ / | | / \ / | | / \ / v v v v v nbp_vlan_add br_vlan_add ------+ | ^ ^ | | | / | | | | / / / | \ br_vlan_get_master/ / v \ ^ / / br_vlan_add_existing \ | / / | \ | / / / \ | / / / \ | / / / \ | / / / v | | v / __vlan_add / / | / / | / v | / __vlan_vid_add | / \ | / v v v br_switchdev_port_vlan_add The ranges UAPI was introduced to the bridge in commit bdced7ef7838 ("bridge: support for multiple vlans and vlan ranges in setlink and dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec) have always been passed one by one, through struct bridge_vlan_info tmp_vinfo, to br_vlan_info. So the range never went too far in depth. Then Scott Feldman introduced the switchdev_port_bridge_setlink function in commit 47f8328bb1a4 ("switchdev: add new switchdev bridge setlink"). That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made full use of the range. But switchdev_port_bridge_setlink was called like this: br_setlink -> br_afspec -> switchdev_port_bridge_setlink Basically, the switchdev and the bridge code were not tightly integrated. Then commit 41c498b9359e ("bridge: restore br_setlink back to original") came, and switchdev drivers were required to implement .ndo_bridge_setlink = switchdev_port_bridge_setlink for a while. In the meantime, commits such as 0944d6b5a2fa ("bridge: try switchdev op first in __vlan_vid_add/del") finally made switchdev penetrate the br_vlan_info() barrier and start to develop the call path we have today. But remember, br_vlan_info() still receives VLANs one by one. Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit 29ab586c3d83 ("net: switchdev: Remove bridge bypass support from switchdev") so that drivers would not implement .ndo_bridge_setlink any longer. The switchdev_port_bridge_setlink also got deleted. This refactoring removed the parallel bridge_setlink implementation from switchdev, and left the only switchdev VLAN objects to be the ones offloaded from __vlan_vid_add (basically RX filtering) and __vlan_add (the latter coming from commit 9c86ce2c1ae3 ("net: bridge: Notify about bridge VLANs")). That is to say, today the switchdev VLAN object ranges are not used in the kernel. Refactoring the above call path is a bit complicated, when the bridge VLAN call path is already a bit complicated. Let's go off and finish the job of commit 29ab586c3d83 by deleting the bogus iteration through the VLAN ranges from the drivers. Some aspects of this feature never made too much sense in the first place. For example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID flag supposed to mean, when a port can obviously have a single pvid? This particular configuration _is_ denied as of commit 6623c60dc28e ("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API perspective, the driver still has to play pretend, and only offload the vlan->vid_end as pvid. And the addition of a switchdev VLAN object can modify the flags of another, completely unrelated, switchdev VLAN object! (a VLAN that is PVID will invalidate the PVID flag from whatever other VLAN had previously been offloaded with switchdev and had that flag. Yet switchdev never notifies about that change, drivers are supposed to guess). Nonetheless, having a VLAN range in the API makes error handling look scarier than it really is - unwinding on errors and all of that. When in reality, no one really calls this API with more than one VLAN. It is all unnecessary complexity. And despite appearing pretentious (two-phase transactional model and all), the switchdev API is really sloppy because the VLAN addition and removal operations are not paired with one another (you can add a VLAN 100 times and delete it just once). The bridge notifies through switchdev of a VLAN addition not only when the flags of an existing VLAN change, but also when nothing changes. There are switchdev drivers out there who don't like adding a VLAN that has already been added, and those checks don't really belong at driver level. But the fact that the API contains ranges is yet another factor that prevents this from being addressed in the future. Of the existing switchdev pieces of hardware, it appears that only Mellanox Spectrum supports offloading more than one VLAN at a time, through mlxsw_sp_port_vlan_set. I have kept that code internal to the driver, because there is some more bookkeeping that makes use of it, but I deleted it from the switchdev API. But since the switchdev support for ranges has already been de facto deleted by a Mellanox employee and nobody noticed for 4 years, I'm going to assume it's not a biggie. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* bridge: switchdev: Notify about VLAN protocol changesDanielle Ratson2020-12-011-0/+2
| | | | | | | | | | | | | | | Drivers that support bridge offload need to be notified about changes to the bridge's VLAN protocol so that they could react accordingly and potentially veto the change. Add a new switchdev attribute to communicate the change to drivers. Signed-off-by: Danielle Ratson <danieller@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* bridge: Add SWITCHDEV_FDB_FLUSH_TO_BRIDGE notifierAlexandra Winter2020-09-151-0/+1
| | | | | | | | | | | | | | | | | | so the switchdev can notifiy the bridge to flush non-permanent fdb entries for this port. This is useful whenever the hardware fdb of the switchdev is reset, but the netdev and the bridgeport are not deleted. Note that this has the same effect as the IFLA_BRPORT_FLUSH attribute. CC: Jiri Pirko <jiri@resnulli.us> CC: Ivan Vecera <ivecera@redhat.com> CC: Roopa Prabhu <roopa@nvidia.com> CC: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Acked-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* switchdev: mrp: Extend switchdev API for MRP InterconnectHoratiu Vultur2020-07-141-0/+38
| | | | | | | | | | | | | | | | | | | Extend switchdev API to add support for MRP interconnect. The HW is notified in the following cases: SWITCHDEV_OBJ_ID_IN_ROLE_MRP: This is used when the interconnect role of the node changes. The supported roles are MIM and MIC. SWITCHDEV_OBJ_ID_IN_STATE_MRP: This is used when the interconnect ring changes it states to open or closed. SWITCHDEV_OBJ_ID_IN_TEST_MRP: This is used to start/stop sending MRP_InTest frames on all MRP ports. This is called only on nodes that have the interconnect role MIM. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: mrp: Add support for role MRAHoratiu Vultur2020-06-011-0/+1
| | | | | | | | | | | | | | | | | | A node that has the MRA role, it can behave as MRM or MRC. Initially it starts as MRM and sends MRP_Test frames on both ring ports. If it detects that there are MRP_Test send by another MRM, then it checks if these frames have a lower priority than itself. In this case it would send MRP_Nack frames to notify the other node that it needs to stop sending MRP_Test frames. If it receives a MRP_Nack frame then it stops sending MRP_Test frames and starts to behave as a MRC but it would continue to monitor the MRP_Test frames send by MRM. If at a point the MRM stops to send MRP_Test frames it would get the MRM role and start to send MRP_Test frames. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: mrp: Set the priority of MRP instanceHoratiu Vultur2020-06-011-0/+1
| | | | | | | | | Each MRP instance has a priority, a lower value means a higher priority. The priority of MRP instance is stored in MRP_Test frame in this way all the MRP nodes in the ring can see other nodes priority. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* switchdev: mrp: Remove the variable mrp_ring_stateHoratiu Vultur2020-05-221-1/+0
| | | | | | | | | | | Remove the variable mrp_ring_state from switchdev_attr because is not used anywhere. The ring state is set using SWITCHDEV_OBJ_ID_RING_STATE_MRP. Fixes: c284b5459008 ("switchdev: mrp: Extend switchdev API to offload MRP") Acked-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* switchdev: mrp: Extend switchdev API to offload MRPHoratiu Vultur2020-04-271-0/+62
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extend switchdev API to add support for MRP. The HW is notified in following cases: SWITCHDEV_OBJ_ID_MRP: This is used when a MRP instance is added/removed from the MRP ring. SWITCHDEV_OBJ_ID_RING_ROLE_MRP: This is used when the role of the node changes. The current supported roles are MRM and MRC. SWITCHDEV_OBJ_ID_RING_TEST_MRP: This is used when to start/stop sending MRP_Test frames on the mrp ring ports. This is called only on nodes that have the role MRM. In case this fails then the SW will generate the frames. SWITCHDEV_OBJ_ID_RING_STATE_STATE: This is used when the ring changes it states to open or closed. This is required to notify HW because the MRP_Test frame contains the field MRP_InState which contains this information. SWITCHDEV_ATTR_ID_MRP_PORT_STATE: This is used when the port's state is changed. It can be in blocking/forwarding mode. SWITCHDEV_ATTR_ID_MRP_PORT_ROLE: This is used when port's role changes. The roles of the port can be primary/secondary. This is required to notify HW because the MRP_Test frame contains the field MRP_PortRole that contains this information. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152Thomas Gleixner2019-05-301-5/+1
| | | | | | | | | | | | | | | | | | | | | Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* switchdev: Remove unused transaction item queueFlorian Fainelli2019-03-011-12/+0
| | | | | | | | | | | | | There are no more in tree users of the switchdev_trans_item_{dequeue,enqueue} or switchdev_trans_item structure in the kernel since commit 00fc0c51e35b ("rocker: Change world_ops API and implementation to be switchdev independant"). Remove this unused code and update the documentation accordingly since. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Remove switchdev_opsFlorian Fainelli2019-02-271-17/+0
| | | | | | | | | | | Now that we have converted all possible callers to using a switchdev notifier for attributes we do not have a need for implementing switchdev_ops anymore, and this can be removed from all drivers the net_device structure. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* switchdev: Add SWITCHDEV_PORT_ATTR_SETFlorian Fainelli2019-02-271-0/+27
| | | | | | | | | | | In preparation for allowing switchdev enabled drivers to veto specific attribute settings from within the context of the caller, introduce a new switchdev notifier type for port attributes. Suggested-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* switchdev: Complete removal of switchdev_port_attr_get()Florian Fainelli2019-02-241-4/+0
| | | | | | | | | We have no more in tree users of switchdev_port_attr_get() after d0e698d57a94 ("Merge branch 'net-Get-rid-of-switchdev_port_attr_get'") so completely remove the function signature and body. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Get rid of switchdev_port_attr_get()Florian Fainelli2019-02-211-8/+0
| | | | | | | | | | | | | | With the bridge no longer calling switchdev_port_attr_get() to obtain the supported bridge port flags from a driver but instead trying to set the bridge port flags directly and relying on driver to reject unsupported configurations, we can effectively get rid of switchdev_port_attr_get() entirely since this was the only place where it was called. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Remove SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORTFlorian Fainelli2019-02-211-2/+0
| | | | | | | | | | | | Now that we have converted the bridge code and the drivers to check for bridge port(s) flags at the time we try to set them, there is no need for a get() -> set() sequence anymore and SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT therefore becomes unused. Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: switchdev: Add PORT_PRE_BRIDGE_FLAGSFlorian Fainelli2019-02-211-1/+2
| | | | | | | | | | | | | | | | In preparation for removing switchdev_port_attr_get(), introduce PORT_PRE_BRIDGE_FLAGS which will be called through switchdev_port_attr_set(), in the caller's context (possibly atomic) and which must be checked by the switchdev driver in order to return whether the operation is supported or not. This is entirely analoguous to how the BRIDGE_FLAGS_SUPPORT works, except it goes through a set() instead of get(). Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_IDFlorian Fainelli2019-02-061-11/+0
| | | | | | | | | | | Now that we have a dedicated NDO for getting a port's parent ID, get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID and convert all callers to use the NDO exclusively. This is a preliminary change to getting rid of switchdev_ops eventually. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* switchdev: Add extack argument to call_switchdev_notifiers()Petr Machata2019-01-171-2/+4
| | | | | | | | | A follow-up patch will enable vetoing of FDB entries. Make it possible to communicate details of why an FDB entry is not acceptable back to the user. Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: switchdev: Add extack to switchdev_handle_port_obj_add() callbackPetr Machata2018-12-121-2/+4
| | | | | | | | | | | | | | | Drivers use switchdev_handle_port_obj_add() to handle recursive descent through lower devices. Change this function prototype to take add_cb that itself takes an extack argument. Decode extack from switchdev_notifier_port_obj_info and pass it to add_cb. Update mlxsw and ocelot drivers which use this helper. Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>