1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
|
// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 2014-15 Synopsys, Inc. (www.synopsys.com)
*/
/*
* Device tree for AXC003 CPU card: HS38x UP configuration
*/
/include/ "skeleton_hs.dtsi"
/ {
compatible = "snps,arc";
#address-cells = <2>;
#size-cells = <2>;
cpu_card {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x00000000 0x0 0xf0000000 0x10000000>;
input_clk: input-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <33333333>;
};
core_clk: core-clk@80 {
compatible = "snps,axs10x-arc-pll-clock";
reg = <0x80 0x10>, <0x100 0x10>;
#clock-cells = <0>;
clocks = <&input_clk>;
/*
* Set initial core pll output frequency to 90MHz.
* It will be applied at the core pll driver probing
* on early boot.
*/
assigned-clocks = <&core_clk>;
assigned-clock-rates = <90000000>;
};
core_intc: archs-intc@cpu {
compatible = "snps,archs-intc";
interrupt-controller;
#interrupt-cells = <1>;
};
/*
* this GPIO block ORs all interrupts on CPU card (creg,..)
* to uplink only 1 IRQ to ARC core intc
*/
dw-apb-gpio@2000 {
compatible = "snps,dw-apb-gpio";
reg = < 0x2000 0x80 >;
#address-cells = <1>;
#size-cells = <0>;
ictl_intc: gpio-controller@0 {
compatible = "snps,dw-apb-gpio-port";
gpio-controller;
#gpio-cells = <2>;
snps,nr-gpios = <30>;
reg = <0>;
interrupt-controller;
#interrupt-cells = <2>;
interrupt-parent = <&core_intc>;
interrupts = <25>;
};
};
debug_uart: dw-apb-uart@5000 {
compatible = "snps,dw-apb-uart";
reg = <0x5000 0x100>;
clock-frequency = <33333000>;
interrupt-parent = <&ictl_intc>;
interrupts = <2 4>;
baud = <115200>;
reg-shift = <2>;
reg-io-width = <4>;
};
arcpct0: pct {
compatible = "snps,archs-pct";
#interrupt-cells = <1>;
interrupt-parent = <&core_intc>;
interrupts = <20>;
};
};
/*
* Mark DMA peripherals connected via IOC port as dma-coherent. We do
* it via overlay because peripherals defined in axs10x_mb.dtsi are
* used for both AXS101 and AXS103 boards and only AXS103 has IOC (so
* only AXS103 board has HW-coherent DMA peripherals)
* We don't need to mark pgu@17000 as dma-coherent because it uses
* external DMA buffer located outside of IOC aperture.
*/
axs10x_mb {
ethernet@18000 {
dma-coherent;
};
ehci@40000 {
dma-coherent;
};
ohci@60000 {
dma-coherent;
};
mmc@15000 {
dma-coherent;
};
};
/*
* The DW APB ICTL intc on MB is connected to CPU intc via a
* DT "invisible" DW APB GPIO block, configured to simply pass thru
* interrupts - setup accordinly in platform init (plat-axs10x/ax10x.c)
*
* So here we mimic a direct connection betwen them, ignoring the
* ABPG GPIO. Thus set "interrupts = <24>" (DW APB GPIO to core)
* instead of "interrupts = <12>" (DW APB ICTL to DW APB GPIO)
*
* This intc actually resides on MB, but we move it here to
* avoid duplicating the MB dtsi file given that IRQ from
* this intc to cpu intc are different for axs101 and axs103
*/
mb_intc: dw-apb-ictl@e0012000 {
#interrupt-cells = <1>;
compatible = "snps,dw-apb-ictl";
reg = < 0x0 0xe0012000 0x0 0x200 >;
interrupt-controller;
interrupt-parent = <&core_intc>;
interrupts = < 24 >;
};
memory {
device_type = "memory";
/* CONFIG_LINUX_RAM_BASE needs to match low mem start */
reg = <0x0 0x80000000 0x0 0x20000000 /* 512 MiB low mem */
0x1 0xc0000000 0x0 0x40000000>; /* 1 GiB highmem */
};
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
/*
* Move frame buffer out of IOC aperture (0x8z-0xaz).
*/
frame_buffer: frame_buffer@be000000 {
compatible = "shared-dma-pool";
reg = <0x0 0xbe000000 0x0 0x2000000>;
no-map;
};
};
};
|
