summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/imx6ull-dhcor-som.dtsi
blob: 32a6022625d979041eb038c70213e696eb81b3ed (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
/*
 * Copyright (C) 2023 DH electronics GmbH
 */

#include <dt-bindings/clock/imx6ul-clock.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pwm/pwm.h>
#include <dt-bindings/regulator/dlg,da9063-regulator.h>
#include "imx6ull.dtsi"

/ {
	memory@80000000 {
		/* Appropriate memory size will be filled by U-Boot */
		reg = <0x80000000 0>;
		device_type = "memory";
	};
};

&cpu0 {
	/*
	 * Due to the design as a solderable SOM, there are no capacitors
	 * below the SoC, therefore higher voltages are required.
	 */
	operating-points = <
		/* kHz	uV */
		900000	1275000
		792000	1250000 /* Voltage increased */
		528000	1175000
		396000	1025000
		198000	950000
	>;
	fsl,soc-operating-points = <
		/* KHz	uV */
		900000	1250000
		792000	1250000 /* Voltage increased */
		528000	1175000
		396000	1175000
		198000	1175000
	>;
};

&gpio1 {
	pinctrl-0 = <&pinctrl_spi1_switch>;
	pinctrl-names = "default";
	/*
	 * Pin SPI_BOOT_FLASH_EN (GPIO 1.9) is a switch for either using the
	 * DHCOM SPI1 interface or accessing the SPI bootflash. Both using
	 * ecspi1, but muxed to different pins. The DHCOM SPI1 interface uses
	 * the pins PAD_LCD_DATA21..23 and the SPI bootflash uses the pins
	 * PAD_CSI_DATA04..07. If the SPI bootflash is enabled the pins for
	 * DHCOM GPIOs N/O/P/Q/R/S/T/U aren't usable anymore, because they
	 * are used for the bus interface to the SPI bootflash. The GPIOs are
	 * disconnected by a buffer which is also controlled via the pin
	 * SPI_BOOT_FLASH_EN. Therefore the access to the bootflash is a
	 * special case and is disabled by setting GPIO 1.9 to high.
	 */
	spi1-switch-hog {
		gpio-hog;
		gpios = <9 0>;
		output-high;
		line-name = "spi1-switch";
	};
};

&i2c1 {
	clock-frequency = <100000>;
	pinctrl-0 = <&pinctrl_i2c1>;
	pinctrl-1 = <&pinctrl_i2c1_gpio>;
	pinctrl-names = "default", "gpio";
	scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
	sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
	status = "okay";

	pmic@58 {
		compatible = "dlg,da9061";
		reg = <0x58>;

		onkey {
			compatible = "dlg,da9061-onkey", "dlg,da9062-onkey";
			status = "disabled";
		};

		regulators {
			vdd_soc_in_1v4: buck1 {
				regulator-allowed-modes = <DA9063_BUCK_MODE_SLEEP>; /* PFM */
				regulator-always-on;
				regulator-boot-on;
				regulator-initial-mode = <DA9063_BUCK_MODE_SLEEP>;
				regulator-max-microvolt = <1400000>;
				regulator-min-microvolt = <1400000>;
				regulator-name = "vdd_soc_in_1v4";
			};

			vcc_3v3: buck2 {
				regulator-allowed-modes = <DA9063_BUCK_MODE_SYNC>; /* PWM */
				regulator-always-on;
				regulator-boot-on;
				regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
				regulator-max-microvolt = <3300000>;
				regulator-min-microvolt = <3300000>;
				regulator-name = "vcc_3v3";
			};

			/*
			 * The current DRR3 memory can be supplied with a
			 * voltage of either 1.35V or 1.5V. For reasons of
			 * backward compatibility to only 1.5V DDR3 memory,
			 * the voltage is set to 1.5V.
			 */
			vcc_ddr_1v35: buck3 {
				regulator-allowed-modes = <DA9063_BUCK_MODE_SYNC>; /* PWM */
				regulator-always-on;
				regulator-boot-on;
				regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
				regulator-max-microvolt = <1500000>;
				regulator-min-microvolt = <1500000>;
				regulator-name = "vcc_ddr_1v35";
			};

			vcc_2v5: ldo1 {
				regulator-always-on;
				regulator-boot-on;
				regulator-max-microvolt = <2500000>;
				regulator-min-microvolt = <2500000>;
				regulator-name = "vcc_2v5";
			};

			vdd_snvs_in_3v3: ldo2 {
				regulator-always-on;
				regulator-boot-on;
				regulator-max-microvolt = <3300000>;
				regulator-min-microvolt = <3300000>;
				regulator-name = "vdd_snvs_in_3v3";
			};

			vcc_1v8: ldo3 {
				regulator-always-on;
				regulator-boot-on;
				regulator-max-microvolt = <1800000>;
				regulator-min-microvolt = <1800000>;
				regulator-name = "vcc_1v8";
			};

			vcc_1v2: ldo4 {
				regulator-always-on;
				regulator-boot-on;
				regulator-max-microvolt = <1200000>;
				regulator-min-microvolt = <1200000>;
				regulator-name = "vcc_1v2";
			};
		};

		thermal {
			compatible = "dlg,da9061-thermal", "dlg,da9062-thermal";
			status = "disabled";
		};

		watchdog {
			compatible = "dlg,da9061-watchdog", "dlg,da9062-watchdog";
			status = "disabled";
		};
	};
};

&ocotp {
	/* Don't get write access by default */
	read-only;
};

&reg_arm {
	vin-supply = <&vdd_soc_in_1v4>;
};

&reg_soc {
	vin-supply = <&vdd_soc_in_1v4>;
};

/* BT on LGA (BT_REG_ON is connected to LGA pin E1) */
&uart2 {
	pinctrl-0 = <&pinctrl_uart2>;
	pinctrl-names = "default";
	uart-has-rtscts;
	status = "okay";

	/*
	 * Actually, the maximum speed of the chip is 4MBdps, but there are
	 * limitations that prevent this speed. It hasn't yet been figured out
	 * what the reason for this is. Currently, the maximum speed of 3MBdps
	 * can be used without any problems. If the limitation can be overcome,
	 * the speed can be increased accordingly.
	 */
	bluetooth: bluetooth {
		compatible = "brcm,bcm43430a1-bt"; /* muRata 1DX */
		max-speed = <3000000>;
		vbat-supply = <&vcc_3v3>;
		vddio-supply = <&vcc_3v3>;
	};
};

/* WiFi on LGA (WL_REG_ON is connected to LGA pin E3) */
&usdhc1 {
	#address-cells = <1>;
	#size-cells = <0>;
	bus-width = <4>;
	no-1-8-v;
	non-removable;
	keep-power-in-suspend;
	pinctrl-0 = <&pinctrl_usdhc1_wifi>;
	pinctrl-names = "default";
	wakeup-source;
	status = "okay";

	brcmf: wifi@1 {
		compatible = "brcm,bcm43430a1-fmac", "brcm,bcm4329-fmac"; /* muRata 1DX */
		reg = <1>;
	};
};

&iomuxc {
	pinctrl_i2c1: i2c1-grp {
		fsl,pins = <
			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL	0x4001b8b0
			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA	0x4001b8b0
		>;
	};

	pinctrl_i2c1_gpio: i2c1-gpio-grp {
		fsl,pins = <
			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28	0x4001b8b0
			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29	0x4001b8b0
		>;
	};

	pinctrl_spi1_switch: spi1-switch-grp {
		fsl,pins = <
			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09	0x120b0 /* SPI_BOOT_FLASH_EN */
		>;
	};

	pinctrl_uart2: uart2-grp {
		fsl,pins = <
			MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX	0x1b0b1
			MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX	0x1b0b1
			MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS	0x1b0b1
			MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS	0x1b0b1
		>;
	};

	pinctrl_usdhc1_wifi: usdhc1-wifi-grp {
		fsl,pins = <
			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x1b0b0
			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10010
			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x1b0b0
			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x1b0b0
			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x1b0b0
			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x1b0b0
		>;
	};
};