blob: 5be11d1b7019ea07c59d6196a925cf93254750ff (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
|
/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* arch/arm/mach-pxa/include/mach/pcm990_baseboard.h
*
* (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de>
* (c) 2007 Juergen Beisert <j.beisert@pengutronix.de>
*/
#include "pcm027.h"
#include <mach/irqs.h> /* PXA_GPIO_TO_IRQ */
/*
* definitions relevant only when the PCM-990
* development base board is in use
*/
/* CPLD's interrupt controller is connected to PCM-027 GPIO 9 */
#define PCM990_CTRL_INT_IRQ_GPIO 9
#define PCM990_CTRL_INT_IRQ PXA_GPIO_TO_IRQ(PCM990_CTRL_INT_IRQ_GPIO)
#define PCM990_CTRL_INT_IRQ_EDGE IRQ_TYPE_EDGE_RISING
#define PCM990_CTRL_PHYS PXA_CS1_PHYS /* 16-Bit */
#define PCM990_CTRL_SIZE (1*1024*1024)
#define PCM990_CTRL_PWR_IRQ_GPIO 14
#define PCM990_CTRL_PWR_IRQ PXA_GPIO_TO_IRQ(PCM990_CTRL_PWR_IRQ_GPIO)
#define PCM990_CTRL_PWR_IRQ_EDGE IRQ_TYPE_EDGE_RISING
/* visible CPLD (U7) registers */
#define PCM990_CTRL_REG0 0x0000 /* RESET REGISTER */
#define PCM990_CTRL_SYSRES 0x0001 /* System RESET REGISTER */
#define PCM990_CTRL_RESOUT 0x0002 /* RESETOUT Enable REGISTER */
#define PCM990_CTRL_RESGPIO 0x0004 /* RESETGPIO Enable REGISTER */
#define PCM990_CTRL_REG1 0x0002 /* Power REGISTER */
#define PCM990_CTRL_5VOFF 0x0001 /* Disable 5V Regulators */
#define PCM990_CTRL_CANPWR 0x0004 /* Enable CANPWR ADUM */
#define PCM990_CTRL_PM_5V 0x0008 /* Read 5V OK */
#define PCM990_CTRL_REG2 0x0004 /* LED REGISTER */
#define PCM990_CTRL_LEDPWR 0x0001 /* POWER LED enable */
#define PCM990_CTRL_LEDBAS 0x0002 /* BASIS LED enable */
#define PCM990_CTRL_LEDUSR 0x0004 /* USER LED enable */
#define PCM990_CTRL_REG3 0x0006 /* LCD CTRL REGISTER 3 */
#define PCM990_CTRL_LCDPWR 0x0001 /* RW LCD Power on */
#define PCM990_CTRL_LCDON 0x0002 /* RW LCD Latch on */
#define PCM990_CTRL_LCDPOS1 0x0004 /* RW POS 1 */
#define PCM990_CTRL_LCDPOS2 0x0008 /* RW POS 2 */
#define PCM990_CTRL_REG4 0x0008 /* MMC1 CTRL REGISTER 4 */
#define PCM990_CTRL_MMC1PWR 0x0001 /* RW MMC1 Power on */
#define PCM990_CTRL_REG5 0x000A /* MMC2 CTRL REGISTER 5 */
#define PCM990_CTRL_MMC2PWR 0x0001 /* RW MMC2 Power on */
#define PCM990_CTRL_MMC2LED 0x0002 /* RW MMC2 LED */
#define PCM990_CTRL_MMC2DE 0x0004 /* R MMC2 Card detect */
#define PCM990_CTRL_MMC2WP 0x0008 /* R MMC2 Card write protect */
#define PCM990_CTRL_INTSETCLR 0x000C /* Interrupt Clear REGISTER */
#define PCM990_CTRL_INTC0 0x0001 /* Clear Reg BT Detect */
#define PCM990_CTRL_INTC1 0x0002 /* Clear Reg FR RI */
#define PCM990_CTRL_INTC2 0x0004 /* Clear Reg MMC1 Detect */
#define PCM990_CTRL_INTC3 0x0008 /* Clear Reg PM_5V off */
#define PCM990_CTRL_INTMSKENA 0x000E /* Interrupt Enable REGISTER */
#define PCM990_CTRL_ENAINT0 0x0001 /* Enable Int BT Detect */
#define PCM990_CTRL_ENAINT1 0x0002 /* Enable Int FR RI */
#define PCM990_CTRL_ENAINT2 0x0004 /* Enable Int MMC1 Detect */
#define PCM990_CTRL_ENAINT3 0x0008 /* Enable Int PM_5V off */
#define PCM990_CTRL_REG8 0x0014 /* Uart REGISTER */
#define PCM990_CTRL_FFSD 0x0001 /* BT Uart Enable */
#define PCM990_CTRL_BTSD 0x0002 /* FF Uart Enable */
#define PCM990_CTRL_FFRI 0x0004 /* FF Uart RI detect */
#define PCM990_CTRL_BTRX 0x0008 /* BT Uart Rx detect */
#define PCM990_CTRL_REG9 0x0010 /* AC97 Flash REGISTER */
#define PCM990_CTRL_FLWP 0x0001 /* pC Flash Write Protect */
#define PCM990_CTRL_FLDIS 0x0002 /* pC Flash Disable */
#define PCM990_CTRL_AC97ENA 0x0004 /* Enable AC97 Expansion */
#define PCM990_CTRL_REG10 0x0012 /* GPS-REGISTER */
#define PCM990_CTRL_GPSPWR 0x0004 /* GPS-Modul Power on */
#define PCM990_CTRL_GPSENA 0x0008 /* GPS-Modul Enable */
#define PCM990_CTRL_REG11 0x0014 /* Accu REGISTER */
#define PCM990_CTRL_ACENA 0x0001 /* Charge Enable */
#define PCM990_CTRL_ACSEL 0x0002 /* Charge Akku -> DC Enable */
#define PCM990_CTRL_ACPRES 0x0004 /* DC Present */
#define PCM990_CTRL_ACALARM 0x0008 /* Error Akku */
/*
* IDE
*/
#define PCM990_IDE_IRQ_GPIO 13
#define PCM990_IDE_IRQ PXA_GPIO_TO_IRQ(PCM990_IDE_IRQ_GPIO)
#define PCM990_IDE_IRQ_EDGE IRQ_TYPE_EDGE_RISING
#define PCM990_IDE_PLD_PHYS 0x20000000 /* 16 bit wide */
#define PCM990_IDE_PLD_BASE 0xee000000
#define PCM990_IDE_PLD_SIZE (1*1024*1024)
/* visible CPLD (U6) registers */
#define PCM990_IDE_PLD_REG0 0x1000 /* OFFSET IDE REGISTER 0 */
#define PCM990_IDE_PM5V 0x0004 /* R System VCC_5V */
#define PCM990_IDE_STBY 0x0008 /* R System StandBy */
#define PCM990_IDE_PLD_REG1 0x1002 /* OFFSET IDE REGISTER 1 */
#define PCM990_IDE_IDEMODE 0x0001 /* R TrueIDE Mode */
#define PCM990_IDE_DMAENA 0x0004 /* RW DMA Enable */
#define PCM990_IDE_DMA1_0 0x0008 /* RW 1=DREQ1 0=DREQ0 */
#define PCM990_IDE_PLD_REG2 0x1004 /* OFFSET IDE REGISTER 2 */
#define PCM990_IDE_RESENA 0x0001 /* RW IDE Reset Bit enable */
#define PCM990_IDE_RES 0x0002 /* RW IDE Reset Bit */
#define PCM990_IDE_RDY 0x0008 /* RDY */
#define PCM990_IDE_PLD_REG3 0x1006 /* OFFSET IDE REGISTER 3 */
#define PCM990_IDE_IDEOE 0x0001 /* RW Latch on Databus */
#define PCM990_IDE_IDEON 0x0002 /* RW Latch on Control Address */
#define PCM990_IDE_IDEIN 0x0004 /* RW Latch on Interrupt usw. */
#define PCM990_IDE_PLD_REG4 0x1008 /* OFFSET IDE REGISTER 4 */
#define PCM990_IDE_PWRENA 0x0001 /* RW IDE Power enable */
#define PCM990_IDE_5V 0x0002 /* R IDE Power 5V */
#define PCM990_IDE_PWG 0x0008 /* R IDE Power is on */
#define PCM990_IDE_PLD_P2V(x) ((x) - PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_BASE)
#define PCM990_IDE_PLD_V2P(x) ((x) - PCM990_IDE_PLD_BASE + PCM990_IDE_PLD_PHYS)
/*
* Compact Flash
*/
#define PCM990_CF_IRQ_GPIO 11
#define PCM990_CF_IRQ PXA_GPIO_TO_IRQ(PCM990_CF_IRQ_GPIO)
#define PCM990_CF_IRQ_EDGE IRQ_TYPE_EDGE_RISING
#define PCM990_CF_CD_GPIO 12
#define PCM990_CF_CD PXA_GPIO_TO_IRQ(PCM990_CF_CD_GPIO)
#define PCM990_CF_CD_EDGE IRQ_TYPE_EDGE_RISING
#define PCM990_CF_PLD_PHYS 0x30000000 /* 16 bit wide */
/* visible CPLD (U6) registers */
#define PCM990_CF_PLD_REG0 0x1000 /* OFFSET CF REGISTER 0 */
#define PCM990_CF_REG0_LED 0x0001 /* RW LED on */
#define PCM990_CF_REG0_BLK 0x0002 /* RW LED flash when access */
#define PCM990_CF_REG0_PM5V 0x0004 /* R System VCC_5V enable */
#define PCM990_CF_REG0_STBY 0x0008 /* R System StandBy */
#define PCM990_CF_PLD_REG1 0x1002 /* OFFSET CF REGISTER 1 */
#define PCM990_CF_REG1_IDEMODE 0x0001 /* RW CF card run as TrueIDE */
#define PCM990_CF_REG1_CF0 0x0002 /* RW CF card at ADDR 0x28000000 */
#define PCM990_CF_PLD_REG2 0x1004 /* OFFSET CF REGISTER 2 */
#define PCM990_CF_REG2_RES 0x0002 /* RW CF RESET BIT */
#define PCM990_CF_REG2_RDYENA 0x0004 /* RW Enable CF_RDY */
#define PCM990_CF_REG2_RDY 0x0008 /* R CF_RDY auf PWAIT */
#define PCM990_CF_PLD_REG3 0x1006 /* OFFSET CF REGISTER 3 */
#define PCM990_CF_REG3_CFOE 0x0001 /* RW Latch on Databus */
#define PCM990_CF_REG3_CFON 0x0002 /* RW Latch on Control Address */
#define PCM990_CF_REG3_CFIN 0x0004 /* RW Latch on Interrupt usw. */
#define PCM990_CF_REG3_CFCD 0x0008 /* RW Latch on CD1/2 VS1/2 usw */
#define PCM990_CF_PLD_REG4 0x1008 /* OFFSET CF REGISTER 4 */
#define PCM990_CF_REG4_PWRENA 0x0001 /* RW CF Power on (CD1/2 = "00") */
#define PCM990_CF_REG4_5_3V 0x0002 /* RW 1 = 5V CF_VCC 0 = 3 V CF_VCC */
#define PCM990_CF_REG4_3B 0x0004 /* RW 3.0V Backup from VCC (5_3V=0) */
#define PCM990_CF_REG4_PWG 0x0008 /* R CF-Power is on */
#define PCM990_CF_PLD_REG5 0x100A /* OFFSET CF REGISTER 5 */
#define PCM990_CF_REG5_BVD1 0x0001 /* R CF /BVD1 */
#define PCM990_CF_REG5_BVD2 0x0002 /* R CF /BVD2 */
#define PCM990_CF_REG5_VS1 0x0004 /* R CF /VS1 */
#define PCM990_CF_REG5_VS2 0x0008 /* R CF /VS2 */
#define PCM990_CF_PLD_REG6 0x100C /* OFFSET CF REGISTER 6 */
#define PCM990_CF_REG6_CD1 0x0001 /* R CF Card_Detect1 */
#define PCM990_CF_REG6_CD2 0x0002 /* R CF Card_Detect2 */
/*
* Wolfson AC97 Touch
*/
#define PCM990_AC97_IRQ_GPIO 10
#define PCM990_AC97_IRQ PXA_GPIO_TO_IRQ(PCM990_AC97_IRQ_GPIO)
#define PCM990_AC97_IRQ_EDGE IRQ_TYPE_EDGE_RISING
/*
* MMC phyCORE
*/
#define PCM990_MMC0_IRQ_GPIO 9
#define PCM990_MMC0_IRQ PXA_GPIO_TO_IRQ(PCM990_MMC0_IRQ_GPIO)
#define PCM990_MMC0_IRQ_EDGE IRQ_TYPE_EDGE_FALLING
/*
* USB phyCore
*/
#define PCM990_USB_OVERCURRENT (88 | GPIO_ALT_FN_1_IN)
#define PCM990_USB_PWR_EN (89 | GPIO_ALT_FN_2_OUT)
|
