blob: d0af4d338e7f201510f169a762d7a5ea56a1b702 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
|
#ifndef _ASM_X86_VISWS_PIIX4_H
#define _ASM_X86_VISWS_PIIX4_H
/*
* PIIX4 as used on SGI Visual Workstations
*/
#define PIIX_PM_START 0x0F80
#define SIO_GPIO_START 0x0FC0
#define SIO_PM_START 0x0FC8
#define PMBASE PIIX_PM_START
#define GPIREG0 (PMBASE+0x30)
#define GPIREG(x) (GPIREG0+((x)/8))
#define GPIBIT(x) (1 << ((x)%8))
#define PIIX_GPI_BD_ID1 18
#define PIIX_GPI_BD_ID2 19
#define PIIX_GPI_BD_ID3 20
#define PIIX_GPI_BD_ID4 21
#define PIIX_GPI_BD_REG GPIREG(PIIX_GPI_BD_ID1)
#define PIIX_GPI_BD_MASK (GPIBIT(PIIX_GPI_BD_ID1) | \
GPIBIT(PIIX_GPI_BD_ID2) | \
GPIBIT(PIIX_GPI_BD_ID3) | \
GPIBIT(PIIX_GPI_BD_ID4) )
#define PIIX_GPI_BD_SHIFT (PIIX_GPI_BD_ID1 % 8)
#define SIO_INDEX 0x2e
#define SIO_DATA 0x2f
#define SIO_DEV_SEL 0x7
#define SIO_DEV_ENB 0x30
#define SIO_DEV_MSB 0x60
#define SIO_DEV_LSB 0x61
#define SIO_GP_DEV 0x7
#define SIO_GP_BASE SIO_GPIO_START
#define SIO_GP_MSB (SIO_GP_BASE>>8)
#define SIO_GP_LSB (SIO_GP_BASE&0xff)
#define SIO_GP_DATA1 (SIO_GP_BASE+0)
#define SIO_PM_DEV 0x8
#define SIO_PM_BASE SIO_PM_START
#define SIO_PM_MSB (SIO_PM_BASE>>8)
#define SIO_PM_LSB (SIO_PM_BASE&0xff)
#define SIO_PM_INDEX (SIO_PM_BASE+0)
#define SIO_PM_DATA (SIO_PM_BASE+1)
#define SIO_PM_FER2 0x1
#define SIO_PM_GP_EN 0x80
/*
* This is the dev/reg where generating a config cycle will
* result in a PCI special cycle.
*/
#define SPECIAL_DEV 0xff
#define SPECIAL_REG 0x00
/*
* PIIX4 needs to see a special cycle with the following data
* to be convinced the processor has gone into the stop grant
* state. PIIX4 insists on seeing this before it will power
* down a system.
*/
#define PIIX_SPECIAL_STOP 0x00120002
#define PIIX4_RESET_PORT 0xcf9
#define PIIX4_RESET_VAL 0x6
#define PMSTS_PORT 0xf80 // 2 bytes PM Status
#define PMEN_PORT 0xf82 // 2 bytes PM Enable
#define PMCNTRL_PORT 0xf84 // 2 bytes PM Control
#define PM_SUSPEND_ENABLE 0x2000 // start sequence to suspend state
/*
* PMSTS and PMEN I/O bit definitions.
* (Bits are the same in both registers)
*/
#define PM_STS_RSM (1<<15) // Resume Status
#define PM_STS_PWRBTNOR (1<<11) // Power Button Override
#define PM_STS_RTC (1<<10) // RTC status
#define PM_STS_PWRBTN (1<<8) // Power Button Pressed?
#define PM_STS_GBL (1<<5) // Global Status
#define PM_STS_BM (1<<4) // Bus Master Status
#define PM_STS_TMROF (1<<0) // Timer Overflow Status.
/*
* Stop clock GPI register
*/
#define PIIX_GPIREG0 (0xf80 + 0x30)
/*
* Stop clock GPI bit in GPIREG0
*/
#define PIIX_GPI_STPCLK 0x4 // STPCLK signal routed back in
#endif /* _ASM_X86_VISWS_PIIX4_H */
|
