1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
menu "CAN Device Drivers"
depends on CAN
config CAN_VCAN
tristate "Virtual Local CAN Interface (vcan)"
depends on CAN
default N
---help---
Similar to the network loopback devices, vcan offers a
virtual local CAN interface.
This driver can also be built as a module. If so, the module
will be called vcan.
config CAN_SLCAN
tristate "Serial / USB serial CAN Adaptors (slcan)"
depends on CAN
default N
---help---
CAN driver for several 'low cost' CAN interfaces that are attached
via serial lines or via USB-to-serial adapters using the LAWICEL
ASCII protocol. The driver implements the tty linediscipline N_SLCAN.
As only the sending and receiving of CAN frames is implemented, this
driver should work with the (serial/USB) CAN hardware from:
www.canusb.com / www.can232.com / www.mictronic.com / www.canhack.de
Userspace tools to attach the SLCAN line discipline (slcan_attach,
slcand) can be found in the can-utils at the SocketCAN SVN, see
http://developer.berlios.de/projects/socketcan for details.
The slcan driver supports up to 10 CAN netdevices by default which
can be changed by the 'maxdev=xx' module option. This driver can
also be built as a module. If so, the module will be called slcan.
config CAN_DEV
tristate "Platform CAN drivers with Netlink support"
depends on CAN
default Y
---help---
Enables the common framework for platform CAN drivers with Netlink
support. This is the standard library for CAN drivers.
If unsure, say Y.
config CAN_CALC_BITTIMING
bool "CAN bit-timing calculation"
depends on CAN_DEV
default Y
---help---
If enabled, CAN bit-timing parameters will be calculated for the
bit-rate specified via Netlink argument "bitrate" when the device
get started. This works fine for the most common CAN controllers
with standard bit-rates but may fail for exotic bit-rates or CAN
source clock frequencies. Disabling saves some space, but then the
bit-timing parameters must be specified directly using the Netlink
arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw".
If unsure, say Y.
config CAN_AT91
tristate "Atmel AT91 onchip CAN controller"
depends on CAN_DEV && ARCH_AT91SAM9263
---help---
This is a driver for the SoC CAN controller in Atmel's AT91SAM9263.
config CAN_TI_HECC
depends on CAN_DEV && ARCH_OMAP3
tristate "TI High End CAN Controller"
---help---
Driver for TI HECC (High End CAN Controller) module found on many
TI devices. The device specifications are available from www.ti.com
config CAN_MCP251X
tristate "Microchip MCP251x SPI CAN controllers"
depends on CAN_DEV && SPI && HAS_DMA
---help---
Driver for the Microchip MCP251x SPI CAN controllers.
config CAN_BFIN
depends on CAN_DEV && (BF534 || BF536 || BF537 || BF538 || BF539 || BF54x)
tristate "Analog Devices Blackfin on-chip CAN"
---help---
Driver for the Analog Devices Blackfin on-chip CAN controllers
To compile this driver as a module, choose M here: the
module will be called bfin_can.
config CAN_JANZ_ICAN3
tristate "Janz VMOD-ICAN3 Intelligent CAN controller"
depends on CAN_DEV && MFD_JANZ_CMODIO
---help---
Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which
connects to a MODULbus carrier board.
This driver can also be built as a module. If so, the module will be
called janz-ican3.ko.
config HAVE_CAN_FLEXCAN
bool
config CAN_FLEXCAN
tristate "Support for Freescale FLEXCAN based chips"
depends on CAN_DEV && HAVE_CAN_FLEXCAN
---help---
Say Y here if you want to support for Freescale FlexCAN.
config PCH_CAN
tristate "PCH CAN"
depends on CAN_DEV && PCI
---help---
This driver is for PCH CAN of Topcliff which is an IOH for x86
embedded processor.
This driver can access CAN bus.
source "drivers/net/can/mscan/Kconfig"
source "drivers/net/can/sja1000/Kconfig"
source "drivers/net/can/usb/Kconfig"
config CAN_DEBUG_DEVICES
bool "CAN devices debugging messages"
depends on CAN
default N
---help---
Say Y here if you want the CAN device drivers to produce a bunch of
debug messages to the system log. Select this if you are having
a problem with CAN support and want to see more of what is going
on.
endmenu
|
