brcm2708: add kernel 4.14 support

Patch generation process:
- rebase rpi/rpi-4.14.y on v4.14.89 from linux-stable
- git format-patch v4.14.89

Patches skipped during rebase:
- lan78xx: Read MAC address from DT if present
- lan78xx: Enable LEDs and auto-negotiation
- Revert "softirq: Let ksoftirqd do its job"
- sc16is7xx: Fix for multi-channel stall
- lan78xx: Ignore DT MAC address if already valid
- lan78xx: Simple patch to prevent some crashes
- tcp_write_queue_purge clears all the SKBs in the write queue
- Revert "lan78xx: Simple patch to prevent some crashes"
- lan78xx: Connect phy early
- Arm: mm: ftrace: Only set text back to ro after kernel has been marked ro
- Revert "Revert "softirq: Let ksoftirqd do its job""
- ASoC: cs4265: SOC_SINGLE register value error fix
- Revert "ASoC: cs4265: SOC_SINGLE register value error fix"
- Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"
- Revert "Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends""

Patches dropped after rebase:
- net: Add non-mainline source for rtl8192cu wlan
- net: Fix rtl8192cu build errors on other platforms
- brcm: adds support for BCM43341 wifi
- brcmfmac: Mute expected startup 'errors'
- ARM64: Fix build break for RTL8187/RTL8192CU wifi
- ARM64: Enable RTL8187/RTL8192CU wifi in build config
- This is the driver for Sony CXD2880 DVB-T2/T tuner + demodulator
- brcmfmac: add CLM download support
- brcmfmac: request_firmware_direct is quieter
- Sets the BCDC priority to constant 0
- brcmfmac: Disable ARP offloading when promiscuous
- brcmfmac: Avoid possible out-of-bounds read
- brcmfmac: Delete redundant length check
- net: rtl8192cu: Normalize indentation
- net: rtl8192cu: Fix implicit fallthrough warnings
- Revert "Sets the BCDC priority to constant 0"
- media: cxd2880: Bump to match 4.18.y version
- media: cxd2880-spi: Bump to match 4.18.y version
- Revert "mm: alloc_contig: re-allow CMA to compact FS pages"
- Revert "Revert "mm: alloc_contig: re-allow CMA to compact FS pages""
- cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with
  MEDIA_SUBDRV_AUTOSELECT
- 950-0421-HID-hid-bigbenff-driver-for-BigBen-Interactive-PS3OF.patch
- 950-0453-Add-hid-bigbenff-to-list-of-have_special_driver-for-.patch

Make I2C built-in instead of modular as in upstream defconfig; also the
easiest way to get MFD_ARIZONA enabled, which is required by
kmod-sound-soc-rpi-cirrus.
Add missing compatible strings from
4.9/960-add-rasbperrypi-compatible.patch, using upstream names for
compute modules.
Add extra patch to enable the LEDs on lan78xx.

Compile-tested: bcm2708, bcm2709, bcm2710 (with CONFIG_ALL_KMODS=y)
Runtime-tested: bcm2708, bcm2710

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

1 files changed, 94 insertions, 0 deletions

diff --git a/target/linux/brcm2708/patches-4.14/950-0326-tc358743-fix-connected-active-CSI-2-lane-reporting.patch b/target/linux/brcm2708/patches-4.14/950-0326-tc358743-fix-connected-active-CSI-2-lane-reporting.patch
new file mode 100644
index 0000000000..cd27a17ce0
--- /dev/null
+++ b/target/linux/brcm2708/patches-4.14/950-0326-tc358743-fix-connected-active-CSI-2-lane-reporting.patch
@@ -0,0 +1,94 @@
+From 39770203c368829b4ddb8b01a68870cc336abc41 Mon Sep 17 00:00:00 2001
+From: Philipp Zabel <p.zabel@pengutronix.de>
+Date: Thu, 21 Sep 2017 17:30:24 +0200
+Subject: [PATCH 326/454] tc358743: fix connected/active CSI-2 lane reporting
+
+g_mbus_config was supposed to indicate all supported lane numbers, not
+only the number of those currently in active use. Since the TC358743
+can dynamically reduce the number of active lanes if the required
+bandwidth allows for it, report all lane numbers up to the connected
+number of lanes as supported in pdata mode.
+In device tree mode, do not report lane count and clock mode at all, as
+the receiver driver can determine these from the device tree.
+
+To allow communicating the number of currently active lanes, add a new
+bitfield to the v4l2_mbus_config flags. This is a temporary fix, to be
+used only until a better solution is found.
+
+Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
+---
+ drivers/media/i2c/tc358743.c  | 30 ++++++++++++++++--------------
+ include/media/v4l2-mediabus.h |  8 ++++++++
+ 2 files changed, 24 insertions(+), 14 deletions(-)
+
+--- a/drivers/media/i2c/tc358743.c
++++ b/drivers/media/i2c/tc358743.c
+@@ -1458,28 +1458,29 @@ static int tc358743_g_mbus_config(struct
+ 			     struct v4l2_mbus_config *cfg)
+ {
+ 	struct tc358743_state *state = to_state(sd);
++	const u32 mask = V4L2_MBUS_CSI2_LANE_MASK;
++
++	if (state->csi_lanes_in_use > state->bus.num_data_lanes)
++		return -EINVAL;
+ 
+ 	cfg->type = V4L2_MBUS_CSI2;
++	cfg->flags = (state->csi_lanes_in_use << __ffs(mask)) & mask;
++
++	/* In DT mode, only report the number of active lanes */
++	if (sd->dev->of_node)
++		return 0;
+ 
+-	/* Support for non-continuous CSI-2 clock is missing in the driver */
+-	cfg->flags = V4L2_MBUS_CSI2_CONTINUOUS_CLOCK;
++	/* Support for non-continuous CSI-2 clock is missing in pdata mode */
++	cfg->flags |= V4L2_MBUS_CSI2_CONTINUOUS_CLOCK;
+ 
+-	switch (state->csi_lanes_in_use) {
+-	case 1:
++	if (state->bus.num_data_lanes > 0)
+ 		cfg->flags |= V4L2_MBUS_CSI2_1_LANE;
+-		break;
+-	case 2:
++	if (state->bus.num_data_lanes > 1)
+ 		cfg->flags |= V4L2_MBUS_CSI2_2_LANE;
+-		break;
+-	case 3:
++	if (state->bus.num_data_lanes > 2)
+ 		cfg->flags |= V4L2_MBUS_CSI2_3_LANE;
+-		break;
+-	case 4:
++	if (state->bus.num_data_lanes > 3)
+ 		cfg->flags |= V4L2_MBUS_CSI2_4_LANE;
+-		break;
+-	default:
+-		return -EINVAL;
+-	}
+ 
+ 	return 0;
+ }
+@@ -1885,6 +1886,7 @@ static int tc358743_probe(struct i2c_cli
+ 	if (pdata) {
+ 		state->pdata = *pdata;
+ 		state->bus.flags = V4L2_MBUS_CSI2_CONTINUOUS_CLOCK;
++		state->bus.num_data_lanes = 4;
+ 	} else {
+ 		err = tc358743_probe_of(state);
+ 		if (err == -ENODEV)
+--- a/include/media/v4l2-mediabus.h
++++ b/include/media/v4l2-mediabus.h
+@@ -63,6 +63,14 @@
+ 					 V4L2_MBUS_CSI2_3_LANE | V4L2_MBUS_CSI2_4_LANE)
+ #define V4L2_MBUS_CSI2_CHANNELS		(V4L2_MBUS_CSI2_CHANNEL_0 | V4L2_MBUS_CSI2_CHANNEL_1 | \
+ 					 V4L2_MBUS_CSI2_CHANNEL_2 | V4L2_MBUS_CSI2_CHANNEL_3)
++/*
++ * Number of lanes in use, 0 == use all available lanes (default)
++ *
++ * This is a temporary fix for devices that need to reduce the number of active
++ * lanes for certain modes, until g_mbus_config() can be replaced with a better
++ * solution.
++ */
++#define V4L2_MBUS_CSI2_LANE_MASK                (0xf << 10)
+ 
+ /**
+  * enum v4l2_mbus_type - media bus type