ramips: use full names for Xiaomi Mi Router devices

This aligns the device/image names of the older Xiaomi Mi Router
devices with their "friendly" model and DEVICE_MODEL properties.

This also reintroduces consistency with the newer devices already
following that scheme.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

1 files changed, 0 insertions, 220 deletions

diff --git a/target/linux/ramips/dts/mt7621_xiaomi_mir3g.dts b/target/linux/ramips/dts/mt7621_xiaomi_mir3g.dts
deleted file mode 100644
index 51f4842255..0000000000
--- a/target/linux/ramips/dts/mt7621_xiaomi_mir3g.dts
+++ /dev/null
@@ -1,220 +0,0 @@
-#include "mt7621.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
-	compatible = "xiaomi,mir3g", "mediatek,mt7621-soc";
-	model = "Xiaomi Mi Router 3G";
-
-	aliases {
-		led-boot = &led_status_yellow;
-		led-failsafe = &led_status_red;
-		led-running = &led_status_blue;
-		led-upgrade = &led_status_yellow;
-		label-mac-device = &gmac0;
-	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8";
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led_status_red: status_red {
-			label = "red:status";
-			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
-		};
-
-		led_status_blue: status_blue {
-			label = "blue:status";
-			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
-		};
-
-		led_status_yellow: status_yellow {
-			label = "yellow:status";
-			gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
-		};
-
-		wan_amber {
-			label = "amber:wan";
-			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "dsa-0.0:01:1Gbps";
-		};
-
-		lan1_amber {
-			label = "amber:lan1";
-			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "dsa-0.0:03:1Gbps";
-		};
-
-		lan2_amber {
-			label = "amber:lan2";
-			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "dsa-0.0:02:1Gbps";
-		};
-	};
-
-	keys {
-		compatible = "gpio-keys";
-
-		reset {
-			label = "reset";
-			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_RESTART>;
-		};
-	};
-
-	reg_usb_vbus: regulator {
-		compatible = "regulator-fixed";
-		regulator-name = "usb_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio 12 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-};
-
-&xhci {
-	vbus-supply = <&reg_usb_vbus>;
-};
-
-&nand {
-	status = "okay";
-
-	partitions {
-		compatible = "fixed-partitions";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		partition@0 {
-			label = "Bootloader";
-			reg = <0x0 0x80000>;
-			read-only;
-		};
-
-		partition@80000 {
-			label = "Config";
-			reg = <0x80000 0x40000>;
-		};
-
-		partition@c0000 {
-			label = "Bdata";
-			reg = <0xc0000 0x40000>;
-			read-only;
-		};
-
-		factory: partition@100000 {
-			label = "factory";
-			reg = <0x100000 0x40000>;
-			read-only;
-		};
-
-		partition@140000 {
-			label = "crash";
-			reg = <0x140000 0x40000>;
-		};
-
-		partition@180000 {
-			label = "crash_syslog";
-			reg = <0x180000 0x40000>;
-		};
-
-		partition@1c0000 {
-			label = "reserved0";
-			reg = <0x1c0000 0x40000>;
-			read-only;
-		};
-
-		/* uboot expects to find kernels at 0x200000 & 0x600000
-		 * referred to as system 1 & system 2 respectively.
-		 * a kernel is considered suitable for handing control over
-		 * if its linux magic number exists & uImage CRC are correct.
-		 * If either of those conditions fail, a matching sys'n'_fail flag
-		 * is set in uboot env & a restart performed in the hope that the
-		 * alternate kernel is okay.
-		 * if neither kernel checksums ok and both are marked failed, system 2
-		 * is booted anyway.
-		 *
-		 * Note uboot's tftp flash install writes the transferred
-		 * image to both kernel partitions.
-		 */
-
-		partition@200000 {
-			label = "kernel_stock";
-			reg = <0x200000 0x400000>;
-		};
-
-		partition@600000 {
-			label = "kernel";
-			reg = <0x600000 0x400000>;
-		};
-
-		/* ubi partition is the result of squashing
-		 * next consecutive stock partitions:
-		 * - rootfs0 (rootfs partition for stock kernel0),
-		 * - rootfs1 (rootfs partition for stock failsafe kernel1),
-		 * - overlay (used as ubi overlay in stock fw)
-		 * resulting 117,5MiB space for packages.
-		 */
-
-		partition@a00000 {
-			label = "ubi";
-			reg = <0xa00000 0x7580000>;
-		};
-	};
-};
-
-&pcie {
-	status = "okay";
-};
-
-&pcie0 {
-	wifi@0,0 {
-		compatible = "pci14c3,7603";
-		reg = <0x0000 0 0 0 0>;
-		mediatek,mtd-eeprom = <&factory 0x0000>;
-		ieee80211-freq-limit = <2400000 2500000>;
-	};
-};
-
-&pcie1 {
-	wifi@0,0 {
-		compatible = "pci14c3,7662";
-		reg = <0x0000 0 0 0 0>;
-		mediatek,mtd-eeprom = <&factory 0x8000>;
-		ieee80211-freq-limit = <5000000 6000000>;
-	};
-};
-
-&gmac0 {
-	mtd-mac-address = <&factory 0xe006>;
-};
-
-&switch0 {
-	ports {
-		port@1 {
-			status = "okay";
-			label = "wan";
-			mtd-mac-address = <&factory 0xe000>;
-		};
-
-		port@2 {
-			status = "okay";
-			label = "lan2";
-		};
-
-		port@3 {
-			status = "okay";
-			label = "lan1";
-		};
-	};
-};
-
-&state_default {
-	gpio {
-		groups = "jtag", "uart2", "uart3", "wdt";
-		function = "gpio";
-	};
-};