diff options
Diffstat (limited to 'package/boot/uboot-oxnas/src/include/configs/ox820.h')
| -rw-r--r-- | package/boot/uboot-oxnas/src/include/configs/ox820.h | 384 |
1 files changed, 0 insertions, 384 deletions
diff --git a/package/boot/uboot-oxnas/src/include/configs/ox820.h b/package/boot/uboot-oxnas/src/include/configs/ox820.h deleted file mode 100644 index 9b6522bbe4..0000000000 --- a/package/boot/uboot-oxnas/src/include/configs/ox820.h +++ /dev/null @@ -1,384 +0,0 @@ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* High Level Configuration Options */ -#define CONFIG_ARM1136 -#define CONFIG_OX820 -#define CONFIG_SYS_GENERIC_BOARD -#define CONFIG_BOARD_EARLY_INIT_F - -#include <asm/arch/cpu.h> /* get chip and board defs */ - -/* make cmd_ide.c quiet when compile */ -#define __io - -/*#define CONFIG_ARCH_CPU_INIT*/ -/*#define CONFIG_DISPLAY_CPUINFO*/ -/*#define CONFIG_DISPLAY_BOARDINFO*/ -/*#define CONFIG_BOARD_EARLY_INIT_F*/ -/*#define CONFIG_SKIP_LOWLEVEL_INIT*/ - -/* mem */ -#define CONFIG_SYS_SDRAM_BASE 0x60000000 -#define CONFIG_NR_DRAM_BANKS 1 -#define CONFIG_MIN_SDRAM_SIZE (128 * 1024 * 1024) /* 128 MB */ -#define CONFIG_MAX_SDRAM_SIZE (512 * 1024 * 1024) /* 512 MB */ -#define CONFIG_SRAM_BASE 0x50000000 -#define CONFIG_SRAM_SIZE (64 * 1024) - -/* need do dma so better keep dcache off */ -#define CONFIG_SYS_DCACHE_OFF - -/* clock */ -#define CONFIG_PLLA_FREQ_MHZ 800 -#define CONFIG_RPSCLK 6250000 -#define CONFIG_SYS_HZ 1000 -#define CONFIG_SYS_CLK_FREQ CONFIG_RPSCLK -#define CONFIG_SYS_TIMERBASE TIMER1_BASE -#define CONFIG_TIMER_PRESCALE TIMER_PRESCALE_16 - -/* serial */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_CLK CONFIG_RPSCLK -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_NS16550_COM1 UART_1_BASE -#define CONFIG_CONS_INDEX 1 - -/* ide */ -#define CONFIG_SYS_ATA_BASE_ADDR 0 -#define CONFIG_SYS_ATA_DATA_OFFSET 0 -#define CONFIG_SYS_ATA_REG_OFFSET 0 -#define CONFIG_SYS_ATA_ALT_OFFSET 0 -#define CONFIG_IDE_PLX -#define CONFIG_SYS_IDE_MAXDEVICE 2 -#define CONFIG_SYS_IDE_MAXBUS 1 -#define CONFIG_IDE_PREINIT -#define CONFIG_LBA48 - -/* nand */ -#define CONFIG_NAND -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE STATIC_CS0_BASE -#define NAND_CLE_ADDR_PIN 19 -#define NAND_ALE_ADDR_PIN 18 -#define MTDPARTS_DEFAULT "mtdparts=41000000.nand:" \ - "14m(boot)," \ - "-(ubi)" -#define MTDIDS_DEFAULT "nand0=41000000.nand" -#define UBIPART_DEFAULT "ubi" - -/* net */ -#define CONFIG_DESIGNWARE_ETH -#define CONFIG_DW_ALTDESCRIPTOR -#define CONFIG_MII -#define CONFIG_CMD_MII -#define CONFIG_PHYLIB -#define CONFIG_PHY_REALTEK -#define CONFIG_PHY_ICPLUS - -/* spl */ -#ifdef CONFIG_SPL_BUILD -#define USE_DL_PREFIX /* rename malloc free etc, so we can override them */ -#endif - -#if defined(CONFIG_BOOT_FROM_NAND) || defined(CONFIG_BOOT_FROM_SATA) -#define CONFIG_SPL -#define CONFIG_SPL_FRAMEWORK -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_SERIAL_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_TEXT_BASE 0x50000000 -#define CONFIG_SPL_STACK (CONFIG_SRAM_BASE + (48 * 1024)) -#define CONFIG_SPL_DISPLAY_PRINT -#define CONFIG_SPL_BSS_DRAM_START 0x65000000 -#define CONFIG_SPL_BSS_DRAM_SIZE 0x01000000 -#define CONFIG_SPL_MALLOC_START 0x66000000 -#endif - -#if defined(CONFIG_BOOT_FROM_NAND) -#define CONFIG_SPL_NAND_SUPPORT -#define BOOT_DEVICE_TYPE "NAND" -#define BOOT_DEVICE_NAND 0xfeedbacc -#define CONFIG_SPL_BOOT_DEVICE BOOT_DEVICE_NAND -#define CONFIG_SPL_NAND_SIMPLE -#define CONFIG_SPL_NAND_ECC -#define CONFIG_SPL_NAND_SOFTECC -#define CONFIG_SYS_NAND_ECCSIZE 512 -#define CONFIG_SYS_NAND_ECCBYTES 6 -#define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47, \ - 48, 49, 50, 51, 52, 53, 54, 55, \ - 56, 57, 58, 59, 60, 61, 62, 63} -#define CONFIG_SYS_NAND_PAGE_SIZE 2048 -#define CONFIG_SYS_NAND_OOBSIZE 64 -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) -#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 -/* pages per erase block */ -#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE) -/* nand spl use 1 erase block, and use bit to byte encode for reliability */ -#define CONFIG_SPL_MAX_SIZE (128 * 1024 / 8) -#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x00040000 -/* spl kernel load is not enabled */ -#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000 -#define CONFIG_CMD_SPL_NAND_OFS 0 -#define CONFIG_CMD_SPL_WRITE_SIZE 1024 -#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100) -/* CONFIG_BOOT_FROM_NAND end */ - -#elif defined(CONFIG_BOOT_FROM_SATA) -#define CONFIG_SPL_BLOCK_SUPPORT -#define BOOT_DEVICE_TYPE "SATA" -#define BOOT_DEVICE_BLOCK 860202 -#define CONFIG_SPL_BOOT_DEVICE BOOT_DEVICE_BLOCK -#define CONFIG_SPL_MAX_SIZE (36 * 1024) -#define CONFIG_SPL_LIBDISK_SUPPORT -#define CONFIG_SPL_BLOCKDEV_INTERFACE "ide" -#define CONFIG_SPL_BLOCKDEV_ID 0 - -#ifdef CONFIG_BOOT_FROM_FAT /* u-boot in fat partition */ - -#define CONFIG_SPL_FAT_SUPPORT - -#define CONFIG_BLOCKDEV_FAT_BOOT_PARTITION 1 /* first partition */ -#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" /* u-boot file name */ -/* enable U-Boot Falcon Mode */ -#define CONFIG_CMD_SPL -#define CONFIG_SPL_OS_BOOT -#define CONFIG_SPL_FAT_LOAD_ARGS_NAME "bootargs.bin" /* boot parameters */ -#define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "falcon.img" /* kernel */ -#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100) - -#elif CONFIG_BOOT_FROM_EXT4 - -#define CONFIG_SPL_EXT4_SUPPORT -#define CONFIG_BLOCKDEV_EXT4_BOOT_PARTITION 1 /* first partition */ -#define CONFIG_SPL_EXT4_LOAD_PAYLOAD_NAME "/boot/u-boot.img" /* u-boot file name */ -/* enable U-Boot Falcon Mode */ -#define CONFIG_CMD_SPL -#define CONFIG_SPL_OS_BOOT -#define CONFIG_SPL_EXT4_LOAD_ARGS_NAME "/boot/bootargs.bin" /* boot parameters */ -#define CONFIG_SPL_EXT4_LOAD_KERNEL_NAME "/boot/falcon.img" /* kernel */ -#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100) - -#else /* u-boot in raw sectors */ - -#define CONFIG_SYS_BLOCK_RAW_MODE_U_BOOT_SECTOR 1024 -/* spl kernel load is not enabled */ -#define CONFIG_SYS_BLOCK_RAW_MODE_KERNEL_SECTOR 4096 -#define CONFIG_SYS_BLOCK_RAW_MODE_ARGS_SECTOR 0 -#define CONFIG_SYS_BLOCK_RAW_MODE_ARGS_SECTORS (1024 / 512) -#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100) - -#endif /* CONFIG_BOOT_FROM_FAT */ -/* CONFIG_BOOT_FROM_SATA end */ - -#else -/* generic, no spl support */ -#endif - -/* boot */ -#define CONFIG_IDENT_STRING " for OXNAS" -#define CONFIG_MACH_TYPE MACH_TYPE_OXNAS -#ifndef CONFIG_SPL_BUILD -/* Enable devicetree support */ -#define CONFIG_OF_LIBFDT -#endif -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_CMDLINE_TAG -#define CONFIG_INITRD_TAG -#define CONFIG_BOOTDELAY 1 -#define CONFIG_ZERO_BOOTDELAY_CHECK -#define CONFIG_DEFAULT_CONSOLE_PARM "console=ttyS0,115200n8 earlyprintk=serial" -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE -/* memtest works on */ -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE) -#define CONFIG_SYS_AUTOLOAD "no" - -#define CONFIG_DEFAULT_CONSOLE CONFIG_DEFAULT_CONSOLE_PARM "\0" -#define CONFIG_BOOTARGS CONFIG_DEFAULT_CONSOLE_PARM -#define CONFIG_BOOTCOMMAND "run nandboot" -#define CONFIG_BOOT_RETRY_TIME -1 -#define CONFIG_RESET_TO_RETRY 60 - -#define CONFIG_NETCONSOLE -#define CONFIG_IPADDR 192.168.50.100 -#define CONFIG_SERVERIP 192.168.50.59 - -/* A sane default configuration... - * When booting without a valid environment in ubi, first to loading and booting - * the kernel image directly above U-Boot, maybe both were loaded there by - * another bootloader. - * Also use that same offset (0x90000) to load the rescue image later on (by - * adding it onto the flash address where U-Boot is supposed to be stored by - * the legacy loader, 0x440000, resulting in offset 0x4d0000 on the flash). - * When coming up with a valid environment in ubi, first try to load the - * kernel from a ubi volume kernel, if that fails, fallback to the rescue - * image stored in boot partition. As a last resort try booting via - * DHCP/TFTP. - * In case there is no valid environment, first probe for a uimage in ram left - * behind by the first bootloader on a tftp boot. - * If that fails, switch to normal boot order and save environment. - * The loader is supposed to be written to flash at offset 0x440000 and loaded to - * RAM at 0x64000000 - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - "load_kernel_ubi=ubi readvol 0x62000000 kernel;\0" \ - "load_kernel_rescue=nand read 0x62000000 0x4e0000 0x400000;\0" \ - "load_kernel_dhcp=dhcp 0x62000000 oxnas-rescue.bin;\0" \ - "boot_kernel=bootm 0x62000000;\0" \ - "boot_ubi=run load_kernel_ubi && run boot_kernel;\0" \ - "boot_rescue=run load_kernel_rescue && run boot_kernel;\0" \ - "boot_dhcp=run load_kernel_dhcp && run boot_kernel;\0" \ - "normalboot=run boot_ubi; run boot_rescue; run boot_dhcp;\0" \ - "firstboot=bootm 0x640a0000; setenv bootcmd run normalboot; " \ - "setenv firstboot; saveenv; run bootcmd; \0" \ - "bootcmd=run firstboot; \0" \ - "console=" CONFIG_DEFAULT_CONSOLE \ - "bootargs=" CONFIG_BOOTARGS "\0" \ - "mtdids=" MTDIDS_DEFAULT "\0" \ - "mtdparts=" MTDPARTS_DEFAULT "\0" \ - -/* env */ -#if defined(CONFIG_BOOT_FROM_NAND) -#define CONFIG_ENV_IS_IN_NAND -#define CONFIG_ENV_OFFSET 0x000C0000 -#define CONFIG_ENV_SIZE 0x00020000 -#define CONFIG_ENV_OFFSET_REDUND 0x00100000 -#define CONFIG_ENV_SIZE_REDUND 0x00020000 -#define CONFIG_ENV_RANGE (CONFIG_ENV_SIZE * 2) -/* CONFIG_BOOT_FROM_NAND end */ - -#elif defined(CONFIG_BOOT_FROM_SATA) -#ifdef CONFIG_BOOT_FROM_EXT4 -#define CONFIG_ENV_IS_IN_EXT4 -#define CONFIG_START_IDE -#define EXT4_ENV_INTERFACE "ide" -#define EXT4_ENV_DEVICE 0 -#define EXT4_ENV_PART 1 -#define EXT4_ENV_FILE "/boot/u-boot.env" -#define CONFIG_ENV_SIZE (16 * 1024) -#else -#define CONFIG_ENV_IS_IN_FAT -#define CONFIG_START_IDE -#define FAT_ENV_INTERFACE "ide" -#define FAT_ENV_DEVICE 0 -#define FAT_ENV_PART 1 -#define FAT_ENV_FILE "u-boot.env" -#define CONFIG_ENV_SIZE (16 * 1024) -#endif -/* CONFIG_BOOT_FROM_SATA end */ -#elif defined(CONFIG_BOOT_FROM_SATA) - -#else -/* generic */ -#define CONFIG_ENV_IS_IN_UBI 1 -#define CONFIG_ENV_UBI_PART UBIPART_DEFAULT -#define CONFIG_ENV_UBI_VOLUME "ubootenv" -#define CONFIG_ENV_UBI_VOLUME_REDUND "ubootenv2" -#define CONFIG_ENV_SIZE (16 * 1024) -#endif - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) -#define CONFIG_SYS_TEXT_BASE 0x64000000 -#define CONFIG_SYS_INIT_SP_ADDR 0x65000000 -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (1 * 1024 * 1024) - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ -#define CONFIG_SYS_PROMPT "OX820 # " -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size*/ -#define CONFIG_SYS_PBSIZE 1024 /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ -#define CONFIG_CMDLINE_EDITING -#define CONFIG_AUTO_COMPLETE - -/* usb */ -#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_USB_EHCI -#define CONFIG_EHCI_IS_TDI -/* #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x3F */ -#define CONFIG_USB_PLLB_CLK -#define CONFIG_USB_EHCI_OXNAS -#ifndef CONFIG_SPL_BUILD -#define CONFIG_USB_STORAGE -#endif -#define CONFIG_CMD_USB - -/* cmds */ -#define CONFIG_SYS_NO_FLASH -#include <config_cmd_default.h> - -#define CONFIG_CMD_SAVEENV -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_GREPENV -#define CONFIG_CMD_ENV_FLAGS - -#define CONFIG_CMD_NET -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PING -#define CONFIG_CMD_PXE - -#define CONFIG_CMD_NAND -#define CONFIG_CMD_MTDPARTS -#define CONFIG_CMD_UBI -#define CONFIG_CMD_UBIFS - -#define CONFIG_CMD_IDE -#define CONFIG_CMD_FAT -#define CONFIG_FAT_WRITE -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_EXT4 -#ifndef CONFIG_SPL_BUILD -#define CONFIG_CMD_EXT4_WRITE -#endif - -#define CONFIG_CMD_ZIP -#define CONFIG_CMD_UNZIP -#define CONFIG_CMD_TIME -#define CONFIG_CMD_SETEXPR -#define CONFIG_CMD_MD5SUM -#define CONFIG_CMD_HASH -#define CONFIG_CMD_INI -#define CONFIG_CMD_GETTIME -#define CONFIG_CMD_BOOTMENU -#define CONFIG_CMD_ELF -#define CONFIG_CMD_BOOTZ - -#define CONFIG_DOS_PARTITION -#define CONFIG_EFI_PARTITION - -/* for CONFIG_CMD_MTDPARTS */ -#define CONFIG_MTD_DEVICE -/* for CONFIG_CMD_UBI */ -#define CONFIG_MTD_PARTITIONS -/* for CONFIG_CMD_UBI */ -#define CONFIG_RBTREE - -/* optional, for CONFIG_CMD_BOOTM & required by CONFIG_CMD_UBIFS */ -#define CONFIG_LZO -#define CONFIG_LZMA -#define CONFIG_BZIP2 - -/* for CONFIG_CMD_ZIP */ -#define CONFIG_GZIP_COMPRESSED -/* for CONFIG_CMD_MD5SUM */ -#define CONFIG_MD5 -#define CONFIG_MD5SUM_VERIFY -/* enable CONFIG_CMD_HASH's verification feature */ -#define CONFIG_HASH_VERIFY -#define CONFIG_REGEX -/* for CONFIG_CMD_BOOTMENU & CONFIG_CMD_PXE */ -#define CONFIG_MENU - -/* for new FIT uImage format generated in OpenWrt */ -#define CONFIG_FIT - -#endif /* __CONFIG_H */ |