diff options
Diffstat (limited to 'target/linux/bcm27xx/patches-5.15/950-0170-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch')
-rw-r--r-- | target/linux/bcm27xx/patches-5.15/950-0170-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch | 77 |
1 files changed, 0 insertions, 77 deletions
diff --git a/target/linux/bcm27xx/patches-5.15/950-0170-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch b/target/linux/bcm27xx/patches-5.15/950-0170-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch deleted file mode 100644 index 49efff3874..0000000000 --- a/target/linux/bcm27xx/patches-5.15/950-0170-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch +++ /dev/null @@ -1,77 +0,0 @@ -From 3c54a4cdc8c65248c347a02b36ac378fe81379ba Mon Sep 17 00:00:00 2001 -From: Dave Stevenson <dave.stevenson@raspberrypi.org> -Date: Wed, 28 Aug 2019 13:34:30 +0100 -Subject: [PATCH] media: dt-bindings: Add binding for the Sony IMX219 - sensor - -The IMX219 is an 8MPix CSI2 sensor, supporting 2 or 4 data lanes. -Document the binding for this device. - -Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org> ---- - .../devicetree/bindings/media/i2c/imx219.txt | 59 +++++++++++++++++++ - 1 file changed, 59 insertions(+) - create mode 100644 Documentation/devicetree/bindings/media/i2c/imx219.txt - ---- /dev/null -+++ b/Documentation/devicetree/bindings/media/i2c/imx219.txt -@@ -0,0 +1,59 @@ -+* Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor -+ -+The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor with -+an active array size of 3280H x 2464V. It is programmable through I2C -+interface. The I2C address is fixed to 0x10 as per sensor data sheet. -+Image data is sent through MIPI CSI-2, which is configured as either 2 or 4 -+data lanes. -+ -+Required Properties: -+- compatible: value should be "sony,imx219" for imx219 sensor -+- reg: I2C bus address of the device -+- clocks: reference to the xclk input clock. -+- clock-names: should be "xclk". -+- DOVDD-supply: Digital I/O voltage supply, 1.8 volts -+- AVDD-supply: Analog voltage supply, 2.8 volts -+- DVDD-supply: Digital core voltage supply, 1.2 volts -+ -+Optional Properties: -+- xclr-gpios: reference to the GPIO connected to the xclr pin, if any. Must be -+ released after all supplies are applied. -+ This is an active high signal to the imx219. -+ -+The imx219 device node should contain one 'port' child node with -+an 'endpoint' subnode. For further reading on port node refer to -+Documentation/devicetree/bindings/media/video-interfaces.txt. -+ -+Endpoint node required properties for CSI-2 connection are: -+- remote-endpoint: a phandle to the bus receiver's endpoint node. -+- clock-lanes: should be set to <0> (clock lane on hardware lane 0) -+- data-lanes: should be set to <1 2>, or <1 2 3 4> (two or four lane CSI-2 -+ supported) -+ -+Example: -+ sensor@10 { -+ compatible = "sony,imx219"; -+ reg = <0x10>; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ clocks = <&imx219_clk>; -+ clock-names = "xclk"; -+ xclr-gpios = <&gpio_sensor 0 0>; -+ DOVDD-supply = <&vgen4_reg>; /* 1.8v */ -+ AVDD-supply = <&vgen3_reg>; /* 2.8v */ -+ DVDD-supply = <&vgen2_reg>; /* 1.2v */ -+ -+ imx219_clk: camera-clk { -+ compatible = "fixed-clock"; -+ #clock-cells = <0>; -+ clock-frequency = <24000000>; -+ }; -+ -+ port { -+ sensor_out: endpoint { -+ remote-endpoint = <&csiss_in>; -+ clock-lanes = <0>; -+ data-lanes = <1 2>; -+ }; -+ }; -+ }; |