summaryrefslogtreecommitdiffstats
path: root/target/linux/mediatek/mt7622/base-files
Commit message (Collapse)AuthorAgeFilesLines
* mediatek: mt7622: add a second u-boot for redmi-ax6sChuanhong Guo2024-03-212-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The vendor u-boot knows nothing about UBI, and we used to have a fixed-size kernel partition for vendor u-boot and UBI for rootfs. However, that fixed partition becomes too small eventually, and expanding it requires complicated procedure. This commit changed the flash layout and added a second u-boot where the kernel supposed to be. Now the vendor u-boot chainloads our mainline u-boot, and our u-boot reads kernel+rootfs from UBI, verifies it, and boot into OpenWrt. There are two possible ways to convert from the old fw: Flash the factory image using mtd (provided by @rany2): mount -o remount,ro / mount -o remount,ro /overlay cd /tmp dd if=factory.bin bs=1M count=4 | mtd write - kernel dd if=factory.bin bs=1M skip=4 | mtd -r write - ubi Or, flash the 2nd u-boot via mtd and upload the firmware to the 2nd u-boot using tftp: 1. prepare a tftp server at 192.168.1.254 to serve the sysupgrade image: openwrt-mediatek-mt7622-xiaomi_redmi-router-ax6s-squashfs-sysupgrade.itb 2. upload the ubi-loader.itb to OpenWrt /tmp, and flash it to the old kernel partition: mtd -r write openwrt-mediatek-mt7622-xiaomi_redmi-router-ax6s-ubi-loader.itb 3. The router should reboot and flash the sysupgrade image via TFTP. Procedure for flashing from vendor firmware shouldn't change. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mediatek: mt7622: simplify 02_networkChukun Pan2024-03-161-15/+6
| | | | | | | | | Most mt7622 devices use the mt7531 switch, which have been switched to dsa driver for a long time. So use dsa as the default configuration and configure these rtl8367s devices separately. This reduces the amount of code. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: drop platform_get_bootdevDaniel Golle2024-02-261-17/+2
| | | | | | | Now that we got fitblk_get_bootdev in /lib/upgrade/common.sh we don't need platform_get_bootdev in each of the subtargets any longer. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI buildDaniel Golle2024-02-153-4/+8
| | | | | | | | | | | | | | | | | Move fip and factory into UBI static volumes. Use fitblk instead of partition parser. !! RUN INSTALLER FIRST !! Existing users of previous OpenWrt releases or snapshot builds will have to **re-run the updated installer** before upgrading to firmware after this commit. DO NOT flash or run even just the initramfs image unless you have run the updated installer which moves the content of the 'factory' partition into a UBI volume. tl;dr: DON'T USE YET! Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: convert unifi6lr-v{1,2,3}-ubootmod to fitblkDaniel Golle2024-02-151-1/+8
| | | | | | No bootloader changes needed in this case, smooth transition. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: convert BPi-R64 to all-UBI layout and fitblkDaniel Golle2024-02-153-13/+30
| | | | | | | Modernize bootloader and flash memory layout of the BPi-R64 similar to how it has also been done for the BPi-R3. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: Add support for D-Link EAGLE PRO AI R32Roland Reinl2024-01-024-9/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | R32 is like the M32 part of the EAGLE PRO AI series from D-Link. Specification: - MT7622BV SoC with 2.4GHz wifi - MT7975AN + MT7915AN for 5GHz - MT7531BE Switch - 512MB RAM - 128 MB flash - 2 LEDs (Status and Internet, both can be either orange or white) - 2 buttons (WPS and Reset) Compared to M32, the R32 has the following differences: - 4 LAN ports instead of 2 - The recory image starts with DLK6E6015001 instaed of DLK6E6010001 - Individual LEDs for power and internet - MAC address is stored at another offset in the ODM partition MAC addresses: - WAN MAC is stored in partition "Odm" at offset 0x81 - LAN (as printed on the device) is WAN MAC + 1 - WLAN MAC (2.4 GHz) is WAN MAC + 2 - WLAN MAC (5GHz) is WAN MAC + 3 Flashing via Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the internet LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin Flashing via uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin. - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface) - Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later - Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin - Reboot the device. OpenWrt should start from flash now Revert back to stock using the Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the internet LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below. Decrypting a D-Link firmware image: - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util - Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile> - Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin Revert back to stock using uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides the previously created backup of the Kernel1 partition. - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to FLASH will start. After a few seconds the stock firmware should start again There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP. It can be used if no backup of the Kernel1 partition is reuqired. Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment. The support for the M32/R32 already includes support for flashing from the OEM web interface: - The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line - The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface - OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap) Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
* mediatek: Add support for D-Link EAGLE PRO AI M32Roland Reinl2023-11-123-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - MT7622BV SoC with 2.4GHz wifi - MT7975AN + MT7915AN for 5GHz - MT7531BE Switch - 512MB RAM - 128 MB flash - 3 LEDs (red, orange, white) - 2 buttons (WPS and Reset) MAC addresses: - WAN MAC is stored in partition "Odm" at offset 0x83 - LAN (as printed on the device) is WAN MAC + 1 - WLAN MAC (2.4 GHz) is WAN MAC + 2 - WLAN MAC (5GHz) is WAN MAC + 3 Disassembly: Remove 4 screws in the bottom and 2 screws in the top (after removing the blue cover on the top), then the board can be pulled out. The pins for the serial console are already labeled on the board (VCC, TX, RX, GND). Serial settings: 3.3V, 115200,8n1 Flashing via Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.25 - Press the reset button while powering on the deivce - Keep the reset button pressed until the status LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-a1-squashfs-recovery.bin Flashing via uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-initramfs-kernel.bin. You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface) - Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later - Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-squashfs-sysupgrade.bin - Reboot the device. OpenWrt should start from flash now Revert back to stock using the Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.25 - Press the reset button while powering on the deivce - Keep the reset button pressed until the status LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below. Decrypting a D-Link firmware image: - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util - Run ./m32-firmware-util M32 --DecryptFactoryImage <OriginalFirmware> <OutputFile> - Example for firmware 1.03.01_HOTFIX: ./m32-firmware-util M32 --DecryptFactoryImage M32-REVA_1.03.01_HOTFIX.enc.bin M32-REVA_1.03.01_HOTFIX.decrypted.bin Revert back to stock using uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides the previously created backup of the Kernel1 partition. You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to FLASH will start. After a few seconds the stock firmware should start again There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP. It can be used if no backup of the Kernel1 partition is reuqired. Flahsing via OEM web interface is currently not possible, the OEM images are encrypted and require a specific memory layout which is not compatible to the partition layout of OpenWrt. Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
* mediatek: add support for Buffalo WSR-3200AX4SINAGAKI Hiroshi2023-09-244-2/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WSR-3200AX4S is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on MT7622B. Specification: - SoC : MediaTek MT7622B - RAM : DDR3 512 MiB - Flash : SPI-NAND 128 MiB (Winbond W25N01GVZEIG) - WLAN : 2.4/5 GHz 4T4R - 2.4 GHz : MediaTek MT7622B (SoC) - 5 GHz : MediaTek MT7915 - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7531 - LEDs/Keys : 6x/5x (2x: buttons, 3x: slide-switches) - UART : through-hole on PCB (J4) - assignment: 3.3V, GND, TX, RX from tri-angle marking - settings : 115200n8 - Power : 12 VDC, 1.5 A Flash instruction using factory.bin image: 1. Boot WSR-3200AX4S with "Router" mode 2. Access to "http://192.168.11.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory.bin image and click update ("更新実行") button 4. Wait ~120 seconds to complete flashing Note: - This device has 2x OS images on flash. The first one will always be used for booting and the secondary is for backup. - This support generates multiple factory*.bin image: - factory.bin : for flashing from OEM WebUI - factory-uboot.bin: for flashing from U-Boot or clean installation via sysupgrade (don't use for normal sysupgrade) Known issues: - Wi-Fi MAC addresses won't be applied to each adapter. MAC Addresses: LAN : C4:3C:EA:xx:xx:60 (board_data, mac (text)) WAN : C4:3C:EA:xx:xx:60 (board_data, mac (text)) 2.4 GHz: C4:3C:EA:xx:xx:61 5 GHz : C4:3C:EA:xx:xx:68 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: expand kernel size to 6MiB for WSR-2533DHP2INAGAKI Hiroshi2023-09-241-1/+2
| | | | | | | | | | Expand kernel partition size on WSR-2533DHP2 for the kernel larger than 4 MiB. To prevent upgrading from old firmware before this commit, bump the compat version to 1.1 and add a message for forced sysupgrade using factory-uboot.bin image. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: set new compat version if booted on R64 and R3Daniel Golle2023-06-061-0/+10
| | | | | | | | | | | | | | | | | If the board comes up with OpenWrt that means that the bootloader is recent enough and knows about the new device tree overlays. Using /etc/board.d/ is not enough in this case because it doesn't overwrite existing configuration which may exist (and is fine to exist) if the user updated with 'sysupgrade -F *.itb' and has kept configuration. They would still need to manually set compat_version even though the fact that the bootloader env has been updated can be implied by the fact that the system has started. Hence we can always set compat_version=1.1 for those two boards using uci-defaults. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: use updated device tree overlay mechanism for BPi-R64Daniel Golle2023-06-051-0/+15
| | | | | | Use new device tree overlay mechanism for the BananaPi BPi-R64 board. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for Netgear WAX206Marcel Ziswiler2023-02-183-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MediaTek MT7622BV * RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK) * Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ) * Wi-Fi 2.4/5 GHz 4T4R: * 2.4 GHz: MediaTek MT7622BV * 5 GHz: MediaTek MT7915AN/MT7975AN * Ethernet: 4x 10/100/1000 Mbps LAN, 1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY) * Switch: MediaTek MT7531AE * LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4, Wifin and Wifia dual-colour LEDs + Reset pin) * UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v, 115200n8 * Power: 12 VDC, 2.5 A Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. * U-Boot allows booting an initramfs image via TFTP as follows: setenv ipaddr 192.168.1.1 setenv serverip 192.168.1.100 tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb bootm Known Limitations: * The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the moment. If connected to a multi-gig port the speed has to be manually set to 1G/full either for the switch port or in OpenWrt. For example add the following to /etc/rc.local to set it on boot: /usr/sbin/ethtool -s wan speed 1000 duplex full Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References to WAX206 GPL source: https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar * openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts DTS file for this device. * openwrt/target/linux/mediatek/image/mt7622.mk Image creation code for this device Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> [fix WAN port (1G only), adjust partition layout, adjust image creation] Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
* mediatek: fix wrong return code in platform_check_image()Chen Minqiang2023-01-291-0/+1
| | | | | | Ensure that the platform_check_image() function returns an error code. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* mediatek: mt7622: fix sysupgrade on MMC on BPi-R64Daniel Golle2023-01-161-0/+1
| | | | | | | | A previous attempt to simplify things went wrong and now sysupgrade is broken on this device. Fix that. Fixes: d640cbac0e ("mediatek: mt7622: don't rely on existing image for sysupgrade") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for reyee AX3200-E5Alex Hansen2022-12-062-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is yet another model of the Ruijie RG-EW3200GX PRO with a slightly different flash layout, install process is the same. Specifications: SoC: MT7622B RAM: 256MB Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR Ethernet: 5x1GbE Switch: MT7531BE WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red) 2Keys: Mesh button + Reset button UART: Marked J19 on board. 3.3v, 115200n1 Power: 12V 2.5A Flash instruction: 1. Serve the initramfs.img using a TFTP server with address 10.10.10.3. 2. Interrupt the uboot startup process via UART. 3. Select "System Load Linux to SDRAM via TFTP" item. 4. (important) Back up firmware(mtd7) partitions with: dd if=/dev/mtd7 of=/tmp/firmware.bin and then download the firmware.bin image via SCP. 5. Flash the OpenWrt sysupgrade firmware. Recovery stock firmware: 1. Transfer the firmware.bin image to the device. 2. Flash the image with: mtd write firmware.bin firmware Signed-off-by: Alex Hansen <mralexh123@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: set persistent wifi mac for bpi-r64 and bpi-r3Daniel Golle2022-11-241-0/+3
| | | | | | | Use persistent MAC address for the built-in wireless interfaces of the BPi-R64 and BPi-R3 development boards. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: don't rely on existing image for sysupgradeDaniel Golle2022-10-191-2/+2
| | | | | | | | Don't reply on mapped rootfs partition but rather just take what ever has been set to the kernel cmdline root= parameter as a hint to decide which media to install sysupgrade to on the BananaPi BPi-R64. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: fill wlan device entries in board.json on mt7622Felix Fietkau2022-10-141-0/+12
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: fix Unifi 6LR network configStijn Tintel2022-09-201-2/+1
| | | | | | | | | | | | | | | | When the v1 and v2 variants of the U6LR were introduced, the board network config was not adapted to the new device names. Due to this, the wrong network config is applied during initial boot. The resulting config has lan, wan and a switch, while this device only has a single ethernet interface without a switch. Fix this by using a wildcard that matches all the variants. Fixes: 15a02471bb85 ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1") Fixes: 5c8d3893a78f ("mediatek: new target ubnt_unifi-6-lr-v1-ubootmod") Fixes: 31d86a1a1192 ("mediatek: add Ubiquiti UniFi 6 LR v2 targets") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: add support for ELECOM WRC-X3200GST3INAGAKI Hiroshi2022-05-212-5/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-X3200GST3 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on MT7622B. Specifications: - SoC : MediaTek MT7622B - RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK) - Flash : SPI-NAND 128 MiB (Winbond W25N01GVZEIG) - WLAN : 2.4/5 GHz 4T4R - 2.4 GHz : MediaTek MT7622B (SoC) - 5 GHz : MediaTek MT7915A - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7531 - LEDs/Keys : 6x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J19: 3.3V, GND, TX, RX from power jack side - 115200n8 - Power : 12 VDC, 1.5 A Flash instruction using factory image: 1. Boot WRC-X3200GST3 normally with "Router" mode 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~120 seconds to complete flashing MAC Addresses: LAN : 04:AB:18:xx:xx:77 (Factory, 0x7FFF4 (hex)) WAN : 04:AB:18:xx:xx:78 (Factory, 0x7FFFA (hex)) 2.4 GHz: 04:AB:18:xx:xx:79 (Factory, 0x4 (hex)) 5 GHz : 04:AB:18:xx:xx:7A (none) Note: - currently, there is no "phy1tpt" trigger for 5 GHz wlan (MT7915) in "trigger" file of LEDs, use "phy1radio" trigger instead Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: Add support for Xiaomi Redmi Router AX6SRichard Huynh2022-03-203-2/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Also known as the "Xiaomi Router AX3200" in western markets, but only the AX6S is widely installation-capable at this time. SoC: MediaTek MT7622B RAM: DDR3 256 MiB (ESMT M15T2G16128A) Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG) WLAN: 2.4/5 GHz 4T4R 2.4 GHz: MediaTek MT7622B 5 GHz: MediaTek MT7915E Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531B LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin) UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8 Power: 12 VDC, 1.5 A Notes: U-Boot passes through the ethaddr from uboot-env partition, but also has been known to reset it to a generic mac address hardcoded in the bootloader. However, bdata is also populated with the ethernet mac addresses, but is also typically never written to. Thus this is used instead. Installation: 1. Flash stock Xiaomi "closed beta" image labelled 'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'. (MD5: 5eedf1632ac97bb5a6bb072c08603ed7) 2. Calculate telnet password from serial number and login 3. Execute commands to prepare device nvram set ssh_en=1 nvram set uart_en=1 nvram set boot_wait=on nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit 4. Download and flash image On computer: python -m http.server On router: cd /tmp wget http://<IP>:8000/factory.bin mtd -r write factory.bin firmware Device should reboot at this point. Reverting to stock: Stock Xiaomi recovery tftp that accepts their signed images, with default ips of 192.168.31.1 + 192.168.31.100. Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img) Triggered by holding reset pin on powerup. A simple implementation of this would be via dnsmasq's dhcp-boot option or using the vendor's (Windows only) recovery tool available on their website. Signed-off-by: Richard Huynh <voxlympha@gmail.com>
* mediatek: add support for Ruijie RG-EW3200GX PROLanghua Ye2022-03-052-1/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | X32 Pro is another product name for it in the Chinese market. Specifications: - SoC: MT7622B - RAM: 256MB - Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR - Ethernet: 5x1GbE - Switch: MT7531BE - WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN - 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red) - 2Keys: Mesh button + Reset button - UART: Marked J19 on board. 3.3v, 115200n1 - Power: 12V 2.5A MAC addresses as verified by OEM firmware: use address source WAN *:F4 ethaddr@product_info LAN *:F5 5g *:F6 2g *:F7 Flash instruction: 1. Serve the initramfs.img using a TFTP server with address 10.10.10.3. 2. Interrupt the uboot startup process via UART. 3. Select "System Load Linux to SDRAM via TFTP" item. 4. (important) Back up firmware(mtd7) partitions with: dd if=/dev/mtd7 of=/tmp/firmware.bin and then download the firmware.bin image via SCP. 5. Flash the OpenWrt sysupgrade firmware. Recovery stock firmware: 1. Transfer the firmware.bin image to the device. 2. Flash the image with: mtd write firmware.bin firmware Signed-off-by: Langhua Ye <y1248289414@outlook.com>
* mediatek: mt7622: drop RAMFS_COPY_BIN and RAMFS_COPY_DATADaniel Golle2022-02-221-2/+0
| | | | | | | | | Now that both, fw_printenv/fw_setenv and fwtool are always present during stage2 sysupgrade, we no longer need to list them in RAMFS_COPY_BIN and RAMFS_COPY_DATA in platform.sh. Drop both variables as they are now unneeded. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: rework and fix mt7622-rfb1-ubi supportFelix Fietkau2022-01-132-3/+5
| | | | | | | | Limit bmt remapping range to cover everything up to and including the kernel image, use the rest of the flash area for ubi. Fix partition table and sysupgrade support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: mt7622: switch to generic eMMC sysupgradeDaniel Golle2021-12-021-17/+4
| | | | | | | Use functions in newly introduced emmc.sh for sysupgrade of the BananaPi BPi-R64. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek/mt7622: unifi-6-lr: fix ucidef network configuration typoMark Mentovai2021-11-191-1/+1
| | | | | | | | There's no such thing as ucidef_set_interfaces_lan. It's ucidef_set_interface_lan. Cc: David Bauer <mail@david-bauer.net> Signed-off-by: Mark Mentovai <mark@moxienet.com>
* mediatek: mt7622: bpi-r64: rewrite MMC uImage.FIT sysupgradeDaniel Golle2021-11-121-16/+13
| | | | | | | | | | Similar to mt7623, also no longer use 'blockdev' and stop relying on in-kernel partition parsers. Instead, strip off all metadata using 'fwtool' while writing the firmware image and scrape the number of blocks written from 'dd', then use that block offset to stash the configuration backup. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: make use of find_mmc_partDaniel Golle2021-11-011-6/+6
| | | | | | | Use find_mmc_part instead of previously introduced get_partition_by_name which requires a custom kernel patch. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: make sure MMC is not busy before commencing sysupgradeDaniel Golle2021-10-281-0/+1
| | | | | | | | | In case of the block device still being in use, re-reading the partition table fails. In that case, abort sysupgrade to avoid corrupting the just-written image because of wrong offsets caused by failure to re-read the partition table. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for TOTOLINK A8000RUChuanhong Guo2021-09-031-0/+6
| | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7622 - RAM: 512MB - Flash: MX35LF1GE4AB 128MB SPI NAND - Ethernet: RTL8367S 5x1GbE - WiFi: 2.4G: MT7622 5G: MT7615N x2 - Other ports: USB3.0 x1 Flash instruction: *important*: upgrade vendor firmware to at least V7.1cu.643_B20200521 1. hold the reset button and power on the device. wait for about 10s before releasing the reset button. 2. upload sysupgrade.bin via u-boot recovery page on http://192.168.1.1 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mediatek: mt7622: add spi-nand support for bananapi bpi-r64Oskari Lemmela2021-04-111-11/+23
| | | | | | | | | | Some of bpi-r64 boards have serial NAND attached to SPI bus. Add SD card image support for installing openwrt to it. Default to nand upgrade if root device is not mmc block device. Separate preloader and uboot images for snand are generated. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* mediatek: add alternative bootchain variant for UniFi 6 LRDaniel Golle2021-04-091-1/+2
| | | | | | | | Builds images for the Ubiquiti Network UniFi 6 LR device running the U-Boot build added by the previous commits. Everything but MTD partitions is moved to dtsi. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: improve sysupgrade on MMCDaniel Golle2021-03-311-49/+12
| | | | | | | Use generic functions to acquire rootdev. Make sure to wipe rootfs_data in case of '-n'. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for Buffalo WSR-2533DHP2INAGAKI Hiroshi2021-03-154-0/+155
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Buffalo WSR-2533DHP2. The device uses the Broadcom TRX image format with a special magic. To be able to boot the images or load them they have to be wrapped with different headers depending how it is loaded. There are multiple ways to install OpenWrt on this device. Boot ramdisk from U-Boot ---------------------------- This will load the image and not write it into the flash. 1. Stop boot menu with "space" key 2. Select "System Load Linux to SDRAM via TFTP." 3. Load this image: openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-initramfs-kernel.bin 4. The system boots the image Write to flash from U-Boot ----------------------------- This will load the image over tftp and directly write it into the flash. 1. Stop boot menu with "space" key 2. Select "System Load Linux Kernel then write to Flash via TFTP." 3. Load this image: openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory-uboot.bin 4. The system writes this image into the flash and boots into it. Write to flash from Web UI ----------------------------- This will load the image over over the Web UI and write it into the flash 1. Open the Web UI 2. Go to "管理" -> "ファームウェア更新" 3. Select "ローカルファイル指定" and click "更新実行" 4. Load this image: openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory.bin 5. The system writes this image into the flash and boots into it. Specifications ------------------- * SoC: MT7622 (4x4 2.4 GHz Wifi) * Wifi: MT7615 (4x4 5 GHz Wifi) * Flash: Winbond W29N01HZ 128MB SLC NAND * RAM 256MB * Ethernet: Realtek RTL8367S (5 x 1GBit/s, SoC via 2.5GBit/s) Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: remove no longer needed sysupgrade hackDaniel Golle2021-03-071-18/+0
| | | | | | | Keeping configuration is now handled in fstools like for other types of flash as well. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: remove execute bit and shebang from 01_ledsAdrian Schmutzler2021-03-061-2/+0
| | | | | | | This was added recently and thus overlooked in 85b1f4d8ca2d ("treewide: remove execute bit and shebang from board.d files"). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-061-1/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: mt7622: check firmware metadataDaniel Golle2021-03-041-0/+1
| | | | | | | | | | All mt7622 devices except for the UBI-variant of the mt7622-rfb1 carry metadata appended to the sysupgrade image. Add it for the mt7622-rfb1-ubi as well and check it on sysupgrade to avoid accidentally flashing firmware for the wrong device (or variant or future DEVICE_COMPAT_VERSION). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: bpi-r64: fix sysupgrade on empty diskDaniel Golle2021-03-011-1/+8
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: rework support for BananaPi BPi-R64Daniel Golle2021-02-282-13/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **What's new** * Bring support for the Bananapi BPi-R64 to the level desirable for a nice hackable routerboard. * Use ARM Trusted Firmware A from source. (goodbye binary preloader) * Use Das U-Boot from source. (see previous commit) * Assemble SD-card image using OpenWrt image-commands. (no gen_sd_cruz_foo.sh added, this is not Raspbian) * Updated kernel options to support root filesystem. * Updated DTS to match OpenWrt LAN ports, known LEDs, buttons, ... * Detect root device, handle sysupgrade, config restore, ... * Wire up (known) LEDs and buttons in OpenWrt-fashion. * Build one set of images from SD-card and eMMC. * Hopefully provide a good example of how things can be done right from scratch. **Installation and images** * Have an empty SD-card at hand * Write stuff to the card, as root (card device is /dev/mmcblkX) - write header, gpt, bl2, atf, u-boot and recovery kernel: `cat *bpi-r64-boot-sdcard.img *bpi-r64-initramfs-recovery.fit > /dev/mmcblkX` - rescan partitions: `blockdev --rereadpt /dev/mmcblkX` - write main system to production partition: `cat *bpi-r64-squashfs-sysupgrade.fit > /dev/mmcblkXp5` * Installation to eMMC works using SD-card bootloader via TFTP When running OpenWrt of SD-card, issue this to trigger installation to eMMC: `fw_setenv bootcmd run emmc_init` Be prepared to serve the content of bin/targets/mediatek/mt7622 on TFTP server address 192.168.1.254. **What's missing** * The red LED is always on, probably a hardware bug. * AHCI (probably needs DTS changes) * Ship SD-card image ready with every needed for eMMC install. * The eMMC has a second, currently unused boot partition. This would be ideal to store the WiFi EEPROM and Ethernet MAC address(es). @sinovoip ideas? Thanks to Thomas Hühn @thuehn for providing the hardware! Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add alternative UBI NAND layout for Linksys E8450Daniel Golle2021-02-283-18/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The vendor flash layout of the Linksys E8450 is problematic as it uses the SPI-NAND chip without any wear-leveling while at the same time wasting a lot of space for padding. Use an all-UBI layout instead, storing the kernel+dtb+squashfs in uImage.FIT standard format in UBI volume 'fit', the read-write overlay in UBI volume 'rootfs_data' as well as reduntant U-Boot environments 'ubootenv' and 'ubootenv2', and a 'recovery' kernel+dtb+initramfs uImage.FIT for dual-boot. ** WARNING ** THIS PROCEDURE CAN EASILY BRICK YOUR DEVICE PERMANENTLY IF NOT CARRIED OUT VERY CAREFULLY AND EXACTLY AS DESCRIBED! Step 0 * Configure your PC to have the static IPv4 address 192.168.1.254/24 * Provide bin/targets/mediatek/mt7622 via TFTP Now continue EITHER with step 1A or 1B, depending on your preference (and on having serial console wired up or not). Step 1A (Using the vendor web interface (or non-UBI OpenWrt install)) In order to update to the new bootloader and UBI-based firmware, use the web browser of your choice to open the routers web-interface accessible on http://192.168.1.1 * Navigate to 'Configuration' -> 'Administration' -> 'Firmware Upgrade' * Upload the file openwrt-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery.itb and proceed with the upgrade. * Once OpenWrt comes up, use SCP to upload the new bootloader files to /tmp on the router: *-mt7622-linksys_e8450-ubi-preloader.bin *-mt7622-linksys_e8450-ubi-bl31-uboot.fip * Connect via SSH as you will now need to replace the bootloader in the Flash. ssh root@192.168.1.1 (the usual warnings) * First of all, backup all the flash now: for mtd in /dev/mtdblock*; do dd if=$mtd of=/tmp/$(basename $mtd); done * Then use SCP to copy /tmp/mtdblock* from the router and keep them safe. You will need them should you ever want to return to the factory firmware! * Now flow the uploaded files: mtd -e /dev/mtd0 write /tmp/*linksys_e8450-ubi-preloader.bin /dev/mtd0 mtd -e /dev/mtd1 write /tmp/*linksys_e8450-ubi-bl31-uboot.fip /dev/mtd1 If and only if both writes look like the completed successfully reboot the router. Now continue with step 2. Step 1B (Using the vendor bootloader serial console) * Use the serial to backup all /dev/mtd* devices before using the stock firmware (you got root shell when connected to serial). * Then reboot and select 'U-Boot Console' in the boot menu. * Copy the following lines, one by one: tftpboot 0x40080000 openwrt-mediatek-mt7622-linksys_e8450-ubi-preloader.bin tftpboot 0x40100000 openwrt-mediatek-mt7622-linksys_e8450-ubi-bl31-uboot.fip nand erase 0x0 0x180000 nand write 0x40080000 0x0 0x180000 reset Now continue with step 2 Step 2 Once the new bootchain comes up, the loader will initialize UBI and the ubootenv volumes. It will then of course fail to find any bootable volume and hence resort to load kernel via TFTP from server 192.168.1.254 while giving itself the address 192.168.1.1 The requested file is called openwrt-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery.itb and your TFTP server should provide exactly that :) It will be written to UBI as recovery image and booted. You can then continue and flash the production OS image, either by using sysupgrade in the booted initramfs recovery OS, or by using the bootloader menu and TFTP. That's it. Go ahead and mess around with a bootchain built almost completely from source (only DRAM calibration blobs are fitted in bl2, and the irreplacable on-chip ROM loader remains, of course). And enjoy U-Boot built with many great features out-of-the-box. You can access the bootloader environment from within OpenWrt using the 'fw_printenv' and 'fw_setenv' commands. Don't be afraid, once you got the new bootchain installed the device should be fairly unbrickable (holding reset button before and during power-on resets things and allows reflashing recovery image via TFTP) Special thanks to @dvn0 (Devan Carpenter) for providing amazingly fast infra for test-builds, allowing for `make clean ; make -j$(nproc)` in less than two minutes :) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add Linksys E8450 supportJohn Crispin2021-02-284-3/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys E8450, also known as Belkin RT3200, is a dual-band IEEE 802.11bgn/ac/ax router based on MediaTek MT7622BV and MediaTek MT7915AN chips. FCC: K7S-03571 and K7S-03572 Hardware highlights: - CPU: MediaTek MT7622BV (2x ARM Cortex-A53 @ 1350 MHz max.) - RAM: 512MB DDR3 - Flash: 128MB SPI-NAND (2k+64) - Ethernet: MT7531BE switch with 5 1000Base-T ports CPU port connected with 2500Base-X - WiFi 2.4 GHz: 802.11bgn 4T4R built-in antennas MT7622VB built-in - WiFi 5 GHz: 802.11ac/ax 4T4R built-in antennas MT7915AN chip on-board via PCIe MT7975AN front-end - Buttons: Reset and WPS - LEDS: 3 user controllable LEDs, 4 wired to switch - USB: USB2.0, single port - no Bluetooth (supported by SoC, not wired on board) - Serial: JST PH 2.0MM 6 Pin connector inside device ----_____________---- [ GND RX - TX - - ] --------------------- - JTAG: unpopulated ARM JTAG 20-pin connector (works) This commit adds support for the device in a way that is compatible with the vendor firmware's bootloader and dual-boot flash layout, the resulting image can directly be flashed using the vendor firmware. Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: add support for Ubiquiti UniFi 6 LRDavid Bauer2021-02-181-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: drop shebang from non-executable lib filesAdrian Schmutzler2021-01-291-2/+0
| | | | | | | | | | | | This drops the shebang from another bunch of files in various /lib folders, as these are sourced and the shebang is useless. Fix execute bit in one case, too. This should cover almost all trivial cases now, i.e. where /lib is actually used for library files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: fix mt7622-rfb1 board supportFelix Fietkau2020-08-061-0/+3
| | | | | | | Make GPIO keys active-low. Add DSA support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: generate UBI images for the rev boardJohn Crispin2020-07-161-0/+3
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: add mt7531 DSA supportJohn Crispin2020-06-071-0/+4
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: add bpi-r64 emmc supportJohn Crispin2020-06-073-7/+43
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: consolidate partition names and settingsJohn Crispin2020-04-061-1/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-26 20:23:12 +0000