1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
|
/dts-v1/;
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "xiaomi,mir3g", "mediatek,mt7621-soc";
model = "Xiaomi Mi Router 3G";
aliases {
led-boot = &led_status_yellow;
led-failsafe = &led_status_red;
led-running = &led_status_blue;
led-upgrade = &led_status_yellow;
};
chosen {
bootargs = "console=ttyS0,115200n8";
};
leds {
compatible = "gpio-leds";
led_status_red: status_red {
label = "mir3g:red:status";
gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
};
led_status_blue: status_blue {
label = "mir3g:blue:status";
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
};
led_status_yellow: status_yellow {
label = "mir3g:yellow:status";
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
};
wan_amber {
label = "mir3g:amber:wan";
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
};
lan1_amber {
label = "mir3g:amber:lan1";
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
};
lan2_amber {
label = "mir3g:amber:lan2";
gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
};
};
button {
compatible = "gpio-keys-polled";
poll-interval = <20>;
reset {
label = "reset";
gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
reg_usb_vbus: regulator {
compatible = "regulator-fixed";
regulator-name = "usb_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
&xhci {
vbus-supply = <®_usb_vbus>;
};
&nand {
status = "okay";
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "Bootloader";
reg = <0x0 0x80000>;
read-only;
};
partition@80000 {
label = "Config";
reg = <0x80000 0x40000>;
};
partition@c0000 {
label = "Bdata";
reg = <0xc0000 0x40000>;
read-only;
};
factory: partition@100000 {
label = "Factory";
reg = <0x100000 0x40000>;
read-only;
};
partition@140000 {
label = "crash";
reg = <0x140000 0x40000>;
};
partition@180000 {
label = "crash_syslog";
reg = <0x180000 0x40000>;
};
partition@1c0000 {
label = "reserved0";
reg = <0x1c0000 0x40000>;
read-only;
};
/* uboot expects to find kernels at 0x200000 & 0x600000
* referred to as system 1 & system 2 respectively.
* a kernel is considered suitable for handing control over
* if its linux magic number exists & uImage CRC are correct.
* If either of those conditions fail, a matching sys'n'_fail flag
* is set in uboot env & a restart performed in the hope that the
* alternate kernel is okay.
* if neither kernel checksums ok and both are marked failed, system 2
* is booted anyway.
*
* Note uboot's tftp flash install writes the transferred
* image to both kernel partitions.
*/
partition@200000 {
label = "kernel_stock";
reg = <0x200000 0x400000>;
};
partition@600000 {
label = "kernel";
reg = <0x600000 0x400000>;
};
/* ubi partition is the result of squashing
* next consecutive stock partitions:
* - rootfs0 (rootfs partition for stock kernel0),
* - rootfs1 (rootfs partition for stock failsafe kernel1),
* - overlay (used as ubi overlay in stock fw)
* resulting 117,5MiB space for packages.
*/
partition@a00000 {
label = "ubi";
reg = <0xa00000 0x7580000>;
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
compatible = "pci14c3,7603";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x0000>;
ieee80211-freq-limit = <2400000 2500000>;
};
};
&pcie1 {
wifi@0,0 {
compatible = "pci14c3,7662";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
ðernet {
mtd-mac-address = <&factory 0xe000>;
mediatek,portmap = "lwlll";
};
&pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "jtag", "uart2", "uart3", "wdt";
ralink,function = "gpio";
};
};
};
|
