Merge tag 'devicetree-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull Devicetree updates from Rob Herring:

 - DT binding schema examples are now validated against the schemas.
   Various examples are fixed due to that.

 - Sync dtc with upstream version v1.5.0-30-g702c1b6c0e73

 - Initial schemas for networking bindings. This includes ethernet, phy
   and mdio common bindings with several Allwinner and stmmac converted
   to the schema.

 - Conversion of more Arm top-level SoC/board bindings to DT schema

 - Conversion of PSCI binding to DT schema

 - Rework Arm CPU schema to coexist with other CPU schemas

 - Add a bunch of missing vendor prefixes and new ones for SoChip,
   Sipeed, Kontron, B&R Industrial Automation GmbH, and Espressif

 - Add Mediatek UART RX wakeup support to binding

 - Add reset to ST UART binding

 - Remove some Linuxisms from the endianness common-properties.txt
   binding

 - Make the flattened DT read-only after init

 - Ignore disabled reserved memory nodes

 - Clean-up some dead code in FDT functions

* tag 'devicetree-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (56 commits)
  dt-bindings: vendor-prefixes: add Sipeed
  dt-bindings: vendor-prefixes: add SoChip
  dt-bindings: 83xx-512x-pci: Drop cell-index property
  dt-bindings: serial: add documentation for Rx in-band wakeup support
  dt-bindings: arm: Convert RDA Micro board/soc bindings to json-schema
  of: unittest: simplify getting the adapter of a client
  of/fdt: pass early_init_dt_reserve_memory_arch() with bool type nomap
  of/platform: Drop superfluous cast in of_device_make_bus_id()
  dt-bindings: usb: ehci: Fix example warnings
  dt-bindings: net: Use phy-mode instead of phy-connection-type
  dt-bindings: simple-framebuffer: Add requirement for pipelines
  dt-bindings: display: Fix simple-framebuffer example
  dt-bindings: net: mdio: Add child nodes
  dt-bindings: net: mdio: Add address and size cells
  dt-bindings: net: mdio: Add a nodename pattern
  dt-bindings: mtd: sunxi-nand: Drop 'maxItems' from child 'reg' property
  dt-bindings: arm: Limit cpus schema to only check Arm 'cpu' nodes
  dt-bindings: backlight: lm3630a: correct schema validation
  dt-bindings: net: dwmac: Deprecate the PHY reset properties
  dt-bindings: net: sun8i-emac: Convert the binding to a schemas
  ...

1 files changed, 1 insertions, 79 deletions

diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt
index 9b9e5b1765dd..2399ee60caed 100644
--- a/Documentation/devicetree/bindings/net/phy.txt
+++ b/Documentation/devicetree/bindings/net/phy.txt
@@ -1,79 +1 @@
-PHY nodes
-
-Required properties:
-
- - interrupts : interrupt specifier for the sole interrupt.
- - reg : The ID number for the phy, usually a small integer
-
-Optional Properties:
-
-- compatible: Compatible list, may contain
-  "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for
-  PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45
-  specifications. If neither of these are specified, the default is to
-  assume clause 22.
-
-  If the PHY reports an incorrect ID (or none at all) then the
-  "compatible" list may contain an entry with the correct PHY ID in the
-  form: "ethernet-phy-idAAAA.BBBB" where
-     AAAA - The value of the 16 bit Phy Identifier 1 register as
-            4 hex digits. This is the chip vendor OUI bits 3:18
-     BBBB - The value of the 16 bit Phy Identifier 2 register as
-            4 hex digits. This is the chip vendor OUI bits 19:24,
-            followed by 10 bits of a vendor specific ID.
-
-  The compatible list should not contain other values than those
-  listed here.
-
-- max-speed: Maximum PHY supported speed (10, 100, 1000...)
-
-- broken-turn-around: If set, indicates the PHY device does not correctly
-  release the turn around line low at the end of a MDIO transaction.
-
-- enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to
-  compensate for the board being designed with the lanes swapped.
-
-- enet-phy-lane-no-swap: If set, indicates that PHY will disable swap of the
-  TX/RX lanes. This property allows the PHY to work correcly after e.g. wrong
-  bootstrap configuration caused by issues in PCB layout design.
-
-- eee-broken-100tx:
-- eee-broken-1000t:
-- eee-broken-10gt:
-- eee-broken-1000kx:
-- eee-broken-10gkx4:
-- eee-broken-10gkr:
-  Mark the corresponding energy efficient ethernet mode as broken and
-  request the ethernet to stop advertising it.
-
-- phy-is-integrated: If set, indicates that the PHY is integrated into the same
-  physical package as the Ethernet MAC. If needed, muxers should be configured
-  to ensure the integrated PHY is used. The absence of this property indicates
-  the muxers should be configured so that the external PHY is used.
-
-- resets: The reset-controller phandle and specifier for the PHY reset signal.
-
-- reset-names: Must be "phy" for the PHY reset signal.
-
-- reset-gpios: The GPIO phandle and specifier for the PHY reset signal.
-
-- reset-assert-us: Delay after the reset was asserted in microseconds.
-  If this property is missing the delay will be skipped.
-
-- reset-deassert-us: Delay after the reset was deasserted in microseconds.
-  If this property is missing the delay will be skipped.
-
-Example:
-
-ethernet-phy@0 {
-	compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c22";
-	interrupt-parent = <&PIC>;
-	interrupts = <35 IRQ_TYPE_EDGE_RISING>;
-	reg = <0>;
-
-	resets = <&rst 8>;
-	reset-names = "phy";
-	reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
-	reset-assert-us = <1000>;
-	reset-deassert-us = <2000>;
-};
+This file has moved to ethernet-phy.yaml.