summaryrefslogtreecommitdiffstats
path: root/Documentation/hwmon/ltc4261
diff options
context:
space:
mode:
authorGuenter Roeck <guenter.roeck@ericsson.com>2010-06-25 11:59:54 -0700
committerGuenter Roeck <guenter.roeck@ericsson.com>2010-10-25 14:11:20 -0700
commite5f5c99a39375ce533aacfdfb269978070121e1c (patch)
tree0abf39b045d772cf11bc401bcb1a36985ad3d99a /Documentation/hwmon/ltc4261
parent2ee321440e3a594dcdd9981e68e5e302447047a2 (diff)
downloadlinux-stable-e5f5c99a39375ce533aacfdfb269978070121e1c.tar.gz
linux-stable-e5f5c99a39375ce533aacfdfb269978070121e1c.tar.bz2
linux-stable-e5f5c99a39375ce533aacfdfb269978070121e1c.zip
hwmon: LTC4261 Hardware monitoring driver
This driver adds support for Linear Technology LTC4261 I2C Negative Voltage Hot Swap Controller. Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu> Reviewed-by: Tom Grennan <tom.grennan@ericsson.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Diffstat (limited to 'Documentation/hwmon/ltc4261')
-rw-r--r--Documentation/hwmon/ltc426163
1 files changed, 63 insertions, 0 deletions
diff --git a/Documentation/hwmon/ltc4261 b/Documentation/hwmon/ltc4261
new file mode 100644
index 000000000000..eba2e2c4b94d
--- /dev/null
+++ b/Documentation/hwmon/ltc4261
@@ -0,0 +1,63 @@
+Kernel driver ltc4261
+=====================
+
+Supported chips:
+ * Linear Technology LTC4261
+ Prefix: 'ltc4261'
+ Addresses scanned: -
+ Datasheet:
+ http://cds.linear.com/docs/Datasheet/42612fb.pdf
+
+Author: Guenter Roeck <guenter.roeck@ericsson.com>
+
+
+Description
+-----------
+
+The LTC4261/LTC4261-2 negative voltage Hot Swap controllers allow a board
+to be safely inserted and removed from a live backplane.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for LTC4261 devices, since there is no register
+which can be safely used to identify the chip. You will have to instantiate
+the devices explicitly.
+
+Example: the following will load the driver for an LTC4261 at address 0x10
+on I2C bus #1:
+$ modprobe ltc4261
+$ echo ltc4261 0x10 > /sys/bus/i2c/devices/i2c-1/new_device
+
+
+Sysfs entries
+-------------
+
+Voltage readings provided by this driver are reported as obtained from the ADC
+registers. If a set of voltage divider resistors is installed, calculate the
+real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the
+value of the divider resistor against the measured voltage and R2 is the value
+of the divider resistor against Ground.
+
+Current reading provided by this driver is reported as obtained from the ADC
+Current Sense register. The reported value assumes that a 1 mOhm sense resistor
+is installed. If a different sense resistor is installed, calculate the real
+current by dividing the reported value by the sense resistor value in mOhm.
+
+The chip has two voltage sensors, but only one set of voltage alarm status bits.
+In many many designs, those alarms are associated with the ADIN2 sensor, due to
+the proximity of the ADIN2 pin to the OV pin. ADIN2 is, however, not available
+on all chip variants. To ensure that the alarm condition is reported to the user,
+report it with both voltage sensors.
+
+in1_input ADIN2 voltage (mV)
+in1_min_alarm ADIN/ADIN2 Undervoltage alarm
+in1_max_alarm ADIN/ADIN2 Overvoltage alarm
+
+in2_input ADIN voltage (mV)
+in2_min_alarm ADIN/ADIN2 Undervoltage alarm
+in2_max_alarm ADIN/ADIN2 Overvoltage alarm
+
+curr1_input SENSE current (mA)
+curr1_alarm SENSE overcurrent alarm